Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “VELOCITY DISTRIBUTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

High-Subsonic Performance Characteristics and Boundary-Layer Investigations of a 12 10-Inch-Inlet-Diameter Conical Diffuser

Performance and boundary-layer data were taken in a 12 degree 10-inch inlet-diameter conical diffuser of 2:1 exit- to inlet-area ratio. These data were taken for two inlet-boundary-layer conditions. The first condition was that of a thinner inlet boundary later (boundary-layer displacement thickness, delta* approximately equal to 0.034) produced by an inlet section approximately 1 inlet diameter in length between the entrance bell and the diffuser. The second condition was a thicker inlet boundary layer (delta* approximately equal to 0.120) produced by an additional inlet section length of approximately 6 diameters. Longitudinal static-pressure distributions were measured fro wall static orifices. Transverse total- and static-pressure surveys were made at the inlet and exit stations. Boundary-layer velocity distributions were measured at seven stations between the inlet and exit. These data were obtained for a Reynolds number (based on inlet diameter) range of 1 x 10(exp 6) to 3.9 x 10(exp 6). The corresponding Mach number range was from M = 0.2 to choking. At the maximum-power-available condition supersonic flow was obtained as far as 4.5 inches downstream from the diffuser inlet with a maximum Mach number of M approximately equal to 1.5. The total-pressure loss through the diffuser in percentage of inlet dynamic pressure was approximately 2.5 percent for the thinner inlet boundary later and 5.5 percent for the thicker inlet boundary later over the lower subsonic range. These valued increased with increasing flow rate- the values for the thicker inlet boundary later more than those for the thinner inlet boundary layer. The diffuser effectiveness, expressed as the ratio of the actual static-pressure rise to the ideal static-pressure rise, was about 85 percent for the thinner inlet boundary layer and about 67 percent for the thicker inlet boundary later in the lower subsonic range. These values decrease with increasing flow rate. Separated flow was observed for both inlet-boundary-layer conditions in the region of adverse pressure gradient just downstream of the transition curvature from inlet section to diffuser. The flow for the thinner-inlet-boundary-layer condition did not fully re-establish itself along the diffuser walls. The thicker inlet-boundary-layer flow, while not completely re-establishing the normal flow pattern downstream of the separated region, did re-establish more successfully than the thinner inlet boundary layer.

Little, B. H., Jr.↗

The Two-Particle Correlation Function for Systems with Long-Range Interactions

In this paper, we study the truncated two-particle correlation function in particle systems with long range interactions. For Coulombian and soft potentials, we define and give well-posedness results for the equilibrium correlations. In the Coulombian case, we prove the onset of the Debye screening length in the equilibrium correlations, for suitable velocity distributions. Additionally, we give precise estimates on the effective range of interaction between particles. In the case of soft potential interaction the equilibrium correlations and their fluxes in the space of velocities are shown to be linearly stable.

97 MATHEMATICS AND COMPUTING↗

Dispersion relation for pure dust Bernstein waves in a non-Maxwellian magnetized dusty plasma

Pure dust Bernstein waves are investigated using non-Maxwellian kappa and (r,q) distribution functions in a collisionless, uniform magnetized dusty plasma. Dispersion relations for both the distributions are derived by considering waves whose frequency is of the order of dust cyclotron frequency, and dispersion curves are plotted. It is observed that the propagation band for dust Bernstein waves is rather narrow as compared with that of the electron Bernstein waves. However, the band width increases for higher harmonics, for both kappa and (r,q) distributions. Effect of dust charge on dispersion curves is also studied, and one observes that with increasing dust charge, the dispersion curves shift toward the lower frequencies. Increasing the dust to ion density ratio ((n{sub d0}/n{sub i0})) causes the dispersion curve to shift toward the higher frequencies. It is also found that for large values of spectral index kappa ({kappa}), the dispersion curves approach to the Maxwellian curves. The (r,q) distribution approaches the kappa distribution for r = 0, whereas for r > 0, the dispersion curves show deviation from the Maxwellian curves as expected. Relevance of this work can be found in astrophysical plasmas, where non-Maxwellian velocity distributions as well as dust particles are commonly observed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Nonlinear kinetic simulation study of the ion–ion streaming instability in single- and multi-ion species plasmas

The nonlinear evolution of the ion–ion streaming instability (IISI) is studied using numerical techniques novel to this problem that afford direct insight into the evolution of the particle distributions of each species. Here, during the linear phase of the instability, we demonstrate quantitative agreement with linear kinetic theory. Subsequently, the electrostatic field generated by the IISI causes ring-like velocity distributions of ions to form that are both heated and slowed to varying degrees relative to their initial flows. Due to variation in the trapping conditions for ion species of differing charge-to-mass ratio, when flows of multiple species interact, the nonlinear evolution of each species can be starkly different: we show a case where a lighter ion species is completely stopped by a heavier ion species via the IISI alone (i.e., without collisions) and, for the first time, demonstrate how the IISI can introduce a relative flow between ion species that initially have the same flow velocities, thereby separating them.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DEEP HUBBLE SPACE TELESCOPE IMAGING IN NGC 6397: STELLAR DYNAMICS

Multi-epoch observations with the Advanced Camera for Surveys on the Hubble Space Telescope provide a unique and comprehensive probe of stellar dynamics within NGC 6397. We are able to confront analytic models of the globular cluster with the observed stellar proper motions. The measured proper motions probe well along the main sequence from 0.8 to below 0.1 M{sub Sun} as well as white dwarfs younger than 1 Gyr. The observed field lies just beyond the half-light radius where standard models of globular cluster dynamics (e.g., based on a lowered Maxwellian phase-space distribution) make very robust predictions for the stellar proper motions as a function of mass. The observed proper motions show no evidence for anisotropy in the velocity distribution; furthermore, the observations agree in detail with a straightforward model of the stellar distribution function. We do not find any evidence that the young white dwarfs have received a natal kick in contradiction with earlier results. Using the observed proper motions of the main-sequence stars, we obtain a kinematic estimate of the distance to NGC 6397 of 2.2{sup +0.5}{sub -0.7} kpc and a mass of the cluster of 1.1 {+-} 0.1 Multiplication-Sign 10{sup 5} M{sub Sun} at the photometric distance of 2.53 kpc. One of the main-sequence stars appears to travel on a trajectory that will escape the cluster, yielding an estimate of the evaporation timescale, over which the number of stars in the cluster decreases by a factor of e, of about 3 Gyr. The proper motions of the youngest white dwarfs appear to resemble those of the most massive main-sequence stars, providing the first direct constraint on the relaxation time of the stars in a globular cluster of greater than or about 0.7 Gyr.

79 ASTRONOMY AND ASTROPHYSICS↗

Simulated Milky Way analogues: implications for dark matter direct searches

We study the implications of galaxy formation on dark matter direct detection using high resolution hydrodynamic simulations of Milky Way-like galaxies simulated within the EAGLE and APOSTLE projects. We identify Milky Way analogues that satisfy observational constraints on the Milky Way rotation curve and total stellar mass. We then extract the dark matter density and velocity distribution in the Solar neighbourhood for this set of Milky Way analogues, and use them to analyse the results of current direct detection experiments. For most Milky Way analogues, the event rates in direct detection experiments obtained from the best fit Maxwellian distribution (with peak speed of 223–289 km/s) are similar to those obtained directly from the simulations. As a consequence, the allowed regions and exclusion limits set by direct detection experiments in the dark matter mass and spin-independent cross section plane shift by a few GeV compared to the Standard Halo Model, at low dark matter masses. For each dark matter mass, the halo-to-halo variation of the local dark matter density results in an overall shift of the allowed regions and exclusion limits for the cross section. However, the compatibility of the possible hints for a dark matter signal from DAMA and CDMS-Si and null results from LUX and SuperCDMS is not improved.

79 ASTRONOMY AND ASTROPHYSICS↗

Cusps in the center of galaxies: a real conflict with observations or a numerical artefact of cosmological simulations?

Galaxy observations and N-body cosmological simulations produce conflicting dark matter halo density profiles for galaxy central regions. While simulations suggest a cuspy and universal density profile (UDP) of this region, the majority of observations favor variable profiles with a core in the center. In this paper, we investigate the convergency of standard N-body simulations, especially in the cusp region, following the approach proposed by [1]. We simulate the well known Hernquist model using the SPH code Gadget-3 and consider the full array of dynamical parameters of the particles. We find that, although the cuspy profile is stable, all integrals of motion characterizing individual particles suffer strong unphysical variations along the whole halo, revealing an effective interaction between the test bodies. This result casts doubts on the reliability of the velocity distribution function obtained in the simulations. Moreover, we find unphysical Fokker-Planck streams of particles in the cusp region. The same streams should appear in cosmological N-body simulations, being strong enough to change the shape of the cusp or even to create it. Our analysis, based on the Hernquist model and the standard SPH code, strongly suggests that the UDPs generally found by the cosmological N-body simulations may be a consequence of numerical effects. A much better understanding of the N-body simulation convergency is necessary before a 'core-cusp problem' can properly be used to question the validity of the CDM model.

79 ASTRONOMY AND ASTROPHYSICS↗

Physical properties of a polar coronal hole from 2 to 5 solar radii

Observations with a white-light coronagraph aboard Skylab are used to determine the boundaries of a coronal hole in the northern polar region and the three-dimensional density structure within the hole between heights of 2 and 5 solar radii. The boundary of the hole is found to be essentially axisymmetric about the polar axis, nearly radial from 3 to 6 solar radii, and located near 25 deg latitude at these heights. The radiances arising from the hole are interpreted as resulting from an axisymmetric density distribution whose logarithmic radial gradient is independent of position within the hole and whose magnitude increases with angular distance away from the hole's axis. The velocity distribution within the hole is obtained from the continuity equation by assuming that the particle flux flowing outward in the hole is similar to that measured for high-speed solar-wind streams at 1 AU, and it is shown that the transition from subsonic to supersonic flow occurs between 2.2 and 3 solar radii.

Munro, R. H.↗

Variation in ejecta size with ejection velocity

The sizes and ranges of over 25,000 secondary craters around twelve large primaries on three different planets were measured and used to infer the size-velocity distribution of that portion of the primary crater ejecta that produced the secondaries. The ballistic equation for spherical bodies was used to convert the ranges to velocities, and the velocities and crater sizes were used in the appropriate Schmidt-Holsapple scaling relation of estimate ejecta sizes, and the velocity exponent was determined. The latter are generally between -1 and -13, with an average value of about -1.9. Problems with data collection made it impossible to determine a simple, unique relation between size and velocity.

Vickery, Ann M.↗

New frictional resistance law for smooth plates

From measurements in the free boundary layer of a plate the laws governing the velocity distribution and a new resistance law are derived which, by increasing Reynolds number Re(sub x) afford lower resistance values than the logarithmic law. The transverse velocities, the shearing stress, and the mixing path profiles were also defined.

Schultz-Grunow, F↗

Control of Cell Migration in Two and Three Dimensions Using Substrate Morphology

We have shown that en masse cell migration of fibroblasts on the planar surface results in a radial outward trajectory, and a spatially dependent velocity distribution that decreases exponentially in time towards the single cell value. If the cells are plated on the surface of aligned electropsun fibers above 1 {mu}m in diameter, they become polarized along the fiber, expressing integrin receptors which follow closely the contours of the fibers. The velocity of the cells on the fibrous scaffold is lower than that on the planar surface, and does not depend on the degree of orientation. Cells on fiber smaller than 1 {mu}m migrate more slowly than on the planar surface, since they appear to have a large concentration of receptors. True three-dimensional migration can be observed when plating the droplet on a scaffold comprises of at least three layers. The cells still continue to migrate on the fibers surfaces, as they diffuse into the lower layers of the fibrous scaffold.

36 MATERIALS SCIENCE↗

The dynamical state of RXCJ1230.7+3439: A multi-substructured merging galaxy cluster

We analyse the kinematical and dynamical state of the galaxy cluster RXCJ1230.7+3439 (RXCJ1230), at $z$ = 0.332 using 93 new spectroscopic redshifts of galaxies acquired at the Telescopio Nazionale Galileo and from SDSS DR16 public data. We study the density galaxy distribution retrieved from photometric SDSS multiband data and find that RXCJ1230 appears as a clearly isolated peak in the redshift space, with a global line-of-sight (LOS) velocity dispersion of $σ$ v = 1004 -122 +147 km s -1 . Several tests applied to the spatial and velocity distributions reveal that RXCJ1230 is a complex system with the presence of three subclusters, located to the southwest, east, and south with respect to the main body of the cluster, containing several bright galaxies (BGs) in their respective cores. Our analyses confirm that the three substructures are in a pre-merger phase, where the main interaction takes place with the southwest subclump, almost in the plane of the sky. We compute a velocity dispersion of $σ$ v ~ 1000 and $σ$ v ~ 800 km s -1 for the main cluster and the southwest substructure, respectively. The central main body and southwest substructure differ by ~870 km s -1 in the LOS velocity. From these data, we estimate a dynamical mass of $M$ 200 = 9.0 ± 1.5 × 1014 $M$ ⊙ and 4.4 ± 3.3 × 1014 $M$ ⊙ for the RXCJ1230 main body and southwest clump, respectively, which reveals that the cluster will undergo a merger characterised by a 2:1 mass ratio impact. We solve a two-body problem for this interaction and find that the most likely solution suggests that the merging axis lies ~17° from the plane of the sky and the subcluster will fully interact in ~0.3 Gyr. However, a slight excess in the X-ray temperature observed in the southwest clump confirms a certain degree of interaction already. The comparison between the dynamical masses and those derived from X-ray data reveals good agreement within errors (differences ~15%), which suggests that the innermost regions (< r 500 ) of the galaxy clumps are almost in hydrostatical equilibrium. In summary, RXCJ1230 is a young but also massive cluster in a pre-merging phase accreting other galaxy systems from its environment.

79 ASTRONOMY AND ASTROPHYSICS↗

Global properties of M31's stellar halo from the splash survey. II. Metallicity profile

We present the metallicity distribution of red giant branch (RGB) stars in M31's stellar halo, derived from photometric metallicity estimates for over 1500 spectroscopically confirmed RGB halo stars. The stellar sample comes from 38 halo fields observed with the Keck/DEIMOS spectrograph, ranging from 9 to 175 kpc in projected distance from M31's center, and includes 52 confirmed M31 halo stars beyond 100 kpc. While a wide range of metallicities is seen throughout the halo, the metal-rich peak of the metallicity distribution function becomes significantly less prominent with increasing radius. The metallicity profile of M31's stellar halo shows a continuous gradient from 9 to ∼100 kpc, with a magnitude of ∼ – 0.01 dex kpc{sup –1}. The stellar velocity distributions in each field are used to identify stars that are likely associated with tidal debris features. The removal of tidal debris features does not significantly alter the metallicity gradient in M31's halo: a gradient is maintained in fields spanning 10-90 kpc. We analyze the halo metallicity profile, as well as the relative metallicities of stars associated with tidal debris features and the underlying halo population, in the context of current simulations of stellar halo formation. We argue that the large-scale gradient in M31's halo implies M31 accreted at least one relatively massive progenitor in the past, while the field to field variation seen in the metallicity profile indicates that multiple smaller progenitors are likely to have contributed substantially to M31's outer halo.

79 ASTRONOMY AND ASTROPHYSICS↗

Undamped electrostatic plasma waves

Electrostatic waves in a collision-free unmagnetized plasma of electrons with fixed ions are investigated for electron equilibrium velocity distribution functions that deviate slightly from Maxwellian. Of interest are undamped waves that are the small amplitude limit of nonlinear excitations, such as electron acoustic waves (EAWs). A deviation consisting of a small plateau, a region with zero velocity derivative over a width that is a very small fraction of the electron thermal speed, is shown to give rise to new undamped modes, which here are named corner modes. The presence of the plateau turns off Landau damping and allows oscillations with phase speeds within the plateau. These undamped waves are obtained in a wide region of the (k,{omega}{sub R}) plane ({omega}{sub R} being the real part of the wave frequency and k the wavenumber), away from the well-known 'thumb curve' for Langmuir waves and EAWs based on the Maxwellian. Results of nonlinear Vlasov-Poisson simulations that corroborate the existence of these modes are described. It is also shown that deviations caused by fattening the tail of the distribution shift roots off of the thumb curve toward lower k-values and chopping the tail shifts them toward higher k-values. In addition, a rule of thumb is obtained for assessing how the existence of a plateau shifts roots off of the thumb curve. Suggestions are made for interpreting experimental observations of electrostatic waves, such as recent ones in nonneutral plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Analysis of in-flight boundary-layer state measurements on a subsonic transport wing in high-lift configuration

Flight experiments on NASA Langley's B737-100 (TSRV) airplane have been conducted to document flow characteristics in order to further the understanding of high-lift flow physics, and to correlate and validate computational predictions and wind-tunnel measurements. The project is a cooperative effort involving NASA, industry, and universities. In addition to focusing on in-flight measurements, the project includes extensive application of various computational techniques, and correlation of flight data with computational results and wind-tunnel measurements. Results obtained in the most recent phase of flight experiments are analyzed and presented in this paper. In-flight measurements include surface pressure distributions, measured using flush pressure taps and pressure belts on the slats, main element, and flap elements; surface shear stresses, measured using Preston tubes; off-surface velocity distributions, measured using shear-layer rakes; aeroelastic deformations of the flap elements, measured using an optical positioning system; and boundary-layer transition phenomena, measured using hot-film anemometers and an infrared imaging system. The analysis in this paper primarily focuses on changes in the boundary-layer state that occurred on the slats, main element, and fore flap as a result of changes in flap setting and/or flight condition. Following a detailed description of the experiment, the boundary-layer state phenomenon will be discussed based on data measured during these recent flight experiments.

vanDam, C. P.↗

An inverse inviscid method for the design of quasi-three dimensional rotating turbomachinery cascades

A new inverse inviscid method suitable for the design of rotating blade sections lying on an arbitrary axisymmetric stream-surface with varying streamtube width is presented. The geometry of the axisymmetric stream-surface and the streamtube width variation with meridional distance, the number of blades, the inlet flow conditions, the rotational speed and the suction and pressure side velocity distributions as functions of the normalized arc-length are given. The flow is considered irrotational in the absolute frame of reference and compressible. The output of the computation is the blade section that satisfies the above data. The method solves the flow equations on a (phi 1, psi) potential function-streamfunction plane for the velocity modulus, W and the flow angle beta; the blade section shape can then be obtained as part of the physical plane geometry by integrating the flow angle distribution along streamlines. The (phi 1, psi) plane is defined so that the monotonic behavior of the potential function is guaranteed, even in cases with high peripheral velocities. The method is validated on a rotating turbine case and used to design new blades. To obtain a closed blade, a set of closure conditions were developed and referred.

Bonataki, E.↗

Computation of two-dimensional electric field from the ion laser induced fluorescence measurements

This paper presents a method of computing two-dimensional electric field from ion laser induced fluorescence (LIF) measurements in a plasma flow. The expression for the field is derived by taking velocity moments of the Boltzmann equation for ions. It was found that the pressure tensor, related to the width of the ion velocity distribution, plays a critical role in the computation of the electric field. Even with the assumption of cold ion flow, the pressure tensor contribution may be significant when velocity spread is caused by other forces. Such a situation occurs in the flow of a Hall thruster, where velocity spread is caused by the ions born at different potentials. LIF measurements of the cylindrical hall thruster plume were used to demonstrate practical application of the derived method. Whenever the pressure tensor components are small as compared to the mean ion drift velocity, the electric field calculations reduce to a simple expression given in terms of mean ion drift velocity and its divergence.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Collisional relaxation of bi-Maxwellian plasma temperatures in magnetized plasmas

In the literature, collisional processes are customarily discussed within the context of the Boltzmann-Balescu-Lenard-Landau type of collision integral, but such an equation is strictly valid for unmagnetized plasmas. For plasmas immersed in the ambient magnetic field, the foundational equation that describes binary collisions must be generalized to include the effects of magnetic field. The present paper makes use of such an equation in order to describe the collisional relaxation of temperatures under the assumption of bi-Maxwellian velocity distribution function. The formalism derived in the present paper may be useful for studying the effects of binary collisions on the isotropization of temperatures in the solar wind plasma, among possible applications.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗