Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STRESS AND LOAD”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

Neutron Diffraction Residual Strain Tensor Measurements Within The Phase IA Weld Mock-up Plate P-5

Oak Ridge National Laboratory (ORNL) has worked with NRC and EPRI to apply neutron and X-ray diffraction methods to characterize the residual stresses in a number of dissimilar metal weld mockups and samples. The design of the Phase IA specimens aimed to enable stress measurements by several methods and computational modeling of the weld residual stresses. The partial groove in the 304L stainless steel plate was filled with weld beads of Alloy 82. A summary of the weld conditions for each plate is provided in Table 1. The plates were constrained along the long edges during and after welding by bolts with spring-loaded washers attached to the 1-inch thick Al backing plate. The purpose was to avoid stress relief due to bending of the welded stainless steel plate. The neutron diffraction method was one of the methods selected by EPRI for non-destructive through thickness strain and stress measurement. Four different plates (P-3 to P-6) were studied by neutron diffraction strain mapping, representing four different welding conditions. Through thickness neutron diffraction strain mappings at NRSF2 for the four plates and associated strain-free d-zero specimens involved measurement along seven lines across the weld and at six to seven depths. The mountings of each plate for neutron diffraction measurements were such that the diffraction vector was parallel to each of the three primary orthogonal directions of the plate: two in-plane directions, longitudinal and transverse, and the direction normal to the plate (shown in left figure within Table 1). From the three orthogonal strains for each location, the residual stresses along the three plate directions were calculated. The principal axes of the strain and stress tensors, however, need not necessarily align with the plate coordinate system. To explore this, plate P-5 was selected for examination of the possibility that the principal axes of strain are not along the sample coordinate system axes. If adequate data could be collected the goal would be to determine the strain tensor's orientation and magnitude of strain along each principle axis direction.

36 MATERIALS SCIENCE↗

Effect of residual stresses on the onset of yielding in a Zr-based metallic glass

Indentation experiments were performed on as-cast and elastically-bent-and-constrained Zr-based metallic glass samples to investigate the effect of strain rate and residual stresses on the onset of yielding in the material. The critical shear stress for the onset of yielding in the as-cast sample was found to be insensitive to the applied strain rate. By contrast, in the elastically-stressed sample, the maximum contact pressure from the Hertzian stress field at the onset of yielding was found to largely decrease under tensile residual stress, but only slightly increase under compressive residual stress. Despite the different residual stresses, the effective shear stress, i.e. the superimposition of residual and Hertzian stress fields, for the onset of yielding in the Zr-based metallic glass was essentially a constant. The constancy of the effective stress for the onset of yielding was discussed in light of a critical excess volume associated with the atomic structure upon loading.

99 GENERAL AND MISCELLANEOUS↗

Damage of Elastomeric Matrix Composites (EMC-rubbers) Under Static Loading Conditions: Experimental and Numerical Study

Elastomeric matrix composites (EMC-rubbers) are considered as isotropic hyper elastic incompressible materials under static loading conditions. As a rubber material element cannot be extended to an infinite stretch ratio, a damage mechanism at large strain is considered. The phenomenon of cavitation plays an important role in the damage of EMCs and influences the toughening mechanism of rubber-modified plastics. Indeed, cavitation in elastomers is thought to be initiated from flaws, which grow primarily due to a hydrostatic tensile stress and ahead of the crack; there will not only be a high stress perpendicular to the plane of the crack but also significant stress components in the other direction. However, there exists historically much discussion on the evolution of the cavitation in elastomers under monotonic and/or static solicitation. Mainly, cavitation instability occurs when the stress levels are sufficiently high so that the void expansion rate becomes infinitely large. Many research works have been performed to understand the effects of rubber cavitation on toughening of plastics. In fact, the cavitation phenomenon is not well known in detail. The most popular idea states that the cavitation is related to the existence of the gas bubbles trapped in the material during the production stage and the growing of the cavities would then be the result of the growing gas bubbles. Further, instable failure mechanism at the end of the cavitation is not well known too.

36 MATERIALS SCIENCE↗

PERFORMANCE EVALUATION OF A SUSTAINABLE AND ENERGY EFFICIENT RE-ROOFING TECHNOLOGY USING FIELD-TEST DATA

Three test attics were constructed to evaluate a new sustainable method of re-roofing utilizing photo-voltaic (PV) laminates, metal roofing panels, and PCM heat sink in the Envelope Systems Research Apparatus (ESRA) facility in the ORNL campus. Figure 1 is a picture of the three attic roofs located adjacent to each other. The leftmost roof is the conventional shingle roof, followed by the metal panel roof incorporating the cool-roof coating, and third from left is the roof with the PCM. On the PCM roof, the PV panels are seen as well; they're labelled from left-to-right as panels 5, 6 and 7. The metal panel roof consists of three metal panels with the cool-roof coating; in further discussion this is referred to as the infrared reflective (IRR) metal roof. The IRR metal panels reflect the incoming solar radiation and then quickly re-emit the remaining absorbed portion, thereby reducing the solar heat gain of the attic. Surface reflectance of the panels were measured using a Solar Spectrum Reflectometer. In the 0.35-2.0 {mu}m wavelength interval, which accounts for more than 94% of the solar energy, the IRR panels have an average reflectance of 0.303. In the infrared portion of the spectrum, the IRR panel reflectance is 0.633. The PCM roof consists of a layer of macro-encapsulated bio-based PCM at the bottom, followed by a 2-cm thick layer of dense fiberglass insulation with a reflective surface on top, and metal panels with pre-installed PV laminates on top. The PCM has a melting point of 29 C (84.2 F) and total enthalpy between 180 and 190 J/g. The PCM was macro-packaged in between two layers of heavy-duty plastic foil forming arrays of PCM cells. Two air cavities, between PCM cells and above the fiberglass insulation, helped the over-the-deck natural air ventilation. It is anticipated that during summer, this extra ventilation will help in reducing the attic-generated cooling loads. The extra ventilation, in conjunction with the PCM heat sink, are used to minimize thermal stresses due to the PV laminates on sunny days. In PV laminates sunlight is converted into electricity and heat simultaneous. In case of building integrated applications, a relatively high solar absorption of amorphous silicon laminates can be utilized during the winter for solar heating purposes with PCM providing necessary heat storage capacity. However, PV laminates may also generate increased building cooling loads during the summer months. Therefore, in this project, the PCM heat sink was to minimize summer heat gains as well. The PCM-fibreglass-PV assembly and the IRR metal panels are capable of being installed directly on top of existing shingle roofs during re-roofing, precluding the need for recycling or disposal of waste materials. The PV laminates installed on the PCM attic are PVL-144 models from Uni-Solar. Each laminate contains 22 triple junction amorphous silicon solar cells connected in series. The silicon cells are of dimensions 356 mm x 239 mm (14-in. x 9.4-in.). The PVL-144 laminate is encapsulated in durable ETFE (poly-ethylene-co-tetrafluoroethylene) high light-transmissive polymer. Table 1 lists the power, voltage and current ratings of the PVL-144 panel.

14 SOLAR ENERGY↗

Determining Individual Phase Properties in a Multi-phase Q&P Steel using Multi-scale Indentation Tests

A new inverse method was developed to predict the stress-strain behaviors of constituent phases in a multi-phase steel using the load-depth curves measured in nanoindentation tests combined with microhardness measurements. A power law hardening response was assumed for each phase, and an empirical relationship between hardness and yield strength was assumed. Adjustment was made to eliminate the indentation size effect and indenter bluntness effect. With the newly developed inverse method and statistical analysis of the hardness histogram for each phase, the average stress-strain curves of individual phases in a quench and partitioning (Q&P) steel, including austenite, tempered martensite and untempered martensite, were calculated and the results were compared with the phase properties obtained by in-situ high energy X-ray diffraction (HEXRD) test. It is demonstrated that multi-scale instrumented indentation tests together with the new inverse method are capable of determining the individual phase flow properties in multi-phase alloys.

Cheng, Guang↗

Progress Report on Alloy 617 Time Dependent Allowables

Time dependent allowable stresses are required in the ASME Boiler and Pressure Vessel Code for design of components in the temperature range where time dependent deformation (i.e., creep) is expected to become significant. There are time dependent allowable stresses in Section IID of the Code for use in the non-nuclear construction codes, however, there are additional criteria that must be considered in developing time dependent allowables for nuclear components. These criteria are specified in Section III NH. St is defined as the lesser of three quantities: 100% of the average stress required to obtain a total (elastic, plastic, primary and secondary creep) strain of 1%; 67% of the minimum stress to cause rupture; and 80% of the minimum stress to cause the initiation of tertiary creep. The values are reported for a range of temperatures and for time increments up to 100,000 hours. These values are determined from uniaxial creep tests, which involve the elevated temperature application of a constant load which is relatively small, resulting in deformation over a long time period prior to rupture. The stress which is the minimum resulting from these criteria is the time dependent allowable stress St. In this report data from a large number of creep and creep-rupture tests on Alloy 617 are analyzed using the ASME Section III NH criteria. Data which are used in the analysis are from the ongoing DOE sponsored high temperature materials program, form Korea Atomic Energy Institute through the Generation IV VHTR Materials Program and historical data from previous HTR research and vendor data generated in developing the alloy. It is found that the tertiary creep criterion determines St at highest temperatures, while the stress to cause 1% total strain controls at low temperatures. The ASME Section III Working Group on Allowable Stress Criteria has recommended that the uncertainties associated with determining the onset of tertiary creep and the lack of significant cavitation associated with early tertiary creep strain suggest that the tertiary creep criteria is not appropriate for this material. If the tertiary creep criterion is dropped from consideration, the stress to rupture criteria determines St at all but the lowest temperatures.

36 MATERIALS SCIENCE↗

Stability of dislocation structures in copper towards stress relaxation investigated by high angular resolution 3D x-ray diffraction.

300 {micro}m thick tensile specimen of OFHC copper is subjected to a tensile loading sequence and deformed to a maximal strain of 3.11%. Using the novel three-dimensional X-ray diffraction method High angular resolution 3DXRD', the evolution of the microstructure within a deeply embedded grain is characterized in-situ by the behavior of individual subgrains. The loading sequence consists of three continuous deformation stages with strain rates of 1.1 x 10{sup -6} s{sup -1} and 3 x 10{sup -2} s{sup -1}, in each case followed by a period of extended stress relaxation at fixed motor positions, as well as an unloading step. In contrast to the deformation stages, during each stress relaxation stage, number, size and orientation of subgrains are found to be constant, while a minor amount of clean-up of the microstructure is observed as narrowing of the radial X-ray diffraction line profile. The associated decrease in the width of the strain distribution indicates homogenization of the elastic strains present in the deformation structure. During reloading, the subgrain structure seemingly starts to develop further when the entire dislocation structure is deforming plastically. Upon unloading of the sample, the average backward strain of the subgrains increases.

36 MATERIALS SCIENCE↗

Atomistic simulations of the mechanical properties of silicon carbide nanowires

Molecular dynamics methods using the Tersoff bond-order potential are performed to study the nanomechanical behavior of [111]-oriented β-SiC nanowires under tension, compression, torsion, combined tension-torsion and combined compression-torsion. Under axial tensile strain, the bonds of the nanowires are just stretched before the failure of nanowires by bond breakage. The failure behavior is found to depend on size and temperatures. Under axial compressive strain, the collapse of the SiC nanowires by yielding or column buckling mode depends on the length and diameters of the nanowires, and the latter is consistent with the analysis of equivalent continuum structures using Euler buckling theory. The nanowires collapse through a phase transformation from crystal to amorphous structure in several atomic layers under torsion strain. Under combined loading the failure and buckling modes are not affected by the torsion with a small torsion rate, but the critical stress decreases with increasing the torsion rate. Torsion buckling occurs before the failure and buckling with a big torsion rate. Plastic deformation appears in the buckling zone with further increasing the combined loading.

36 MATERIALS SCIENCE↗

X-ray scattering from a material under an external load

The differential X-ray scattering cross section of a polycrystalline sample placed in a high-pressure chamber under an arbitrary load has been calculated. It is shown that the broadening and displacement of most diffraction lines under shear load are, generally speaking, of the same order of magnitude, except for the reflections on the vectors parallel to threefold and higher order axes (these reflections do not undergo broad-ening). The scattering line shape contains information about the components of the compressibility tensor; to derive it, one needs a diffractometer resolution satisfying the condition {delta}{theta}/{theta} < {tau}/G ({tau} is the shear stress and G is the typical shear modulus of the material studied). An experiment under hydrostatic load is analyzed, and it is shown that the differential bulk compressibility modulus of a polycrystal under pressure, which are derived from X-ray data, coincides with the value given by the natural strain theory.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Deformation of Granular Material under Continuous Rotation of Stress Principal Axes

The mechanical response of granular material to the rotation of stress principal axes is an issue of both practical and theoretical importance in soil mechanics. This study used a two-dimensional (2D) discrete-element method (DEM) simulation to investigate the deformation of granular material under the continuous rotation of stress principal axes while maintaining fixed principal stress values. The results show that under such rotation, the deformation can exceed that caused by fixed principal stress axes cyclic biaxial compression with a maximum deviatoric stress ratio that equals the fixed stress ratio during rotation. The volumetric strain was found to be contractive overall while oscillating within each load cycle for specimens with significant fabric anisotropy. Here, the initial fabric-anisotropy orientation was found to have little influence on the overall evolution of volumetric strain, although it was found to affect the development of shear strain. During the cycles of rotation of initial stress principal axes, the dilatancy of granular material, in the contractive direction, was found to be dominated by the evolving orientation of the major principal stress axis in reference to the initial major principal stress axis during anisotropic consolidation, and the influence of the initial fabric-anisotropy orientation was found to be trivial. As stress rotation continued, the influence of the relative orientation between stress and fabric became prominent, causing the material to dilate when the major principal stress axis rotated from the normal of the bedding plane to being perpendicular to it and causing contraction during the other half of the cycle.

58 GEOSCIENCES↗

Analysis of Nonclassical Fracture Problems for Prestressed Bodies with Interacting Cracks

We consider two types of nonclassical fracture mechanisms, namely, the fracture of cracked bodies with initial (residual) stresses acting along the crack planes and the fracture of solids under compression along parallel cracks. To investigate nonaxisymmetric and axisymmetric problems for infinite solids containing two parallel coaxial cracks or a periodic set of coaxial parallel cracks, we use a combined analytic-numerical method within the framework of the three-dimensional linearized mechanics of solids. The analysis involves the representation of stresses and displacements in the linearized theory via harmonic potential functions. With the use of the integral Fourier–Hankel transformations, the problems are reduced to the solution of Fredholm integral equations of the second kind. This approach allows us to investigate problems in a unified general form for compressible and noncompressible homogeneous isotropic or transversely isotropic elastic bodies with an arbitrary structure of the elastic potential, and the material specification of the model is carried out only in the stage of numerical analysis of the resolving equations obtained in the general form. The effects of initial stresses on the stress intensity factors are analyzed for highly elastic materials and layered composites (modeled as transversely isotropic elastic bodies). The “resonance-like” effects are revealed when compressive initial stresses reach the values corresponding to the local loss of stability of the material in the vicinity of cracks, which, according to the indicated combined method, allows one to determine the critical (limiting) load parameters under the conditions of compression of the body along the cracks. The conclusions concerning the dependences of the stress intensity factors and critical (limiting) parameters of compression on the geometric parameters of the problems are formulated as well as concerning the dependences on physical and mechanical characteristics of the materials.

42 ENGINEERING↗

Creep and microstructural processes in a low-alloy 2.25%Cr1.6%W steel (ASTM Grade 23)

A low-alloy 2.25%Cr1%Mo steel (ASTM Grade 22) has been greatly improved by the substitution of almost all of the 1%Mo by 1.6%W. The improved material has been standardized as P/T23 steel (Fe–2.25Cr–1.6W–0.25V–0.05Nb–0.07C). The present investigation was conducted on T23 steel in an effort to obtain a more complete description and understanding of the role of the microstructural evolution and deformation processes in high-temperature creep. Constant load tensile creep tests were carried out in an argon atmosphere in the temperature range 500–650 °C at stresses ranging from 50 to 400 MPa. It was found that the diffusion in the matrix lattice is the creep-rate controlling process. The results of an extensive transmission electron microscopy (TEM) analysis programme to investigate microstructure evolution as a function of temperature are described and compared with the thermodynamic calculations using the software package Thermo-Calc. The significant creep-strength drop of T23 steel after long-term creep exposures can be explained by the decrease in dislocation hardening, precipitation hardening and solid solution hardening due to the instability of the microstructure at high temperature. - Highlights: • The constant load creep tests of T23 steel were carried out at 500–650 °C. • The stress exponents of the creep rate correspond to power law (dislocation) creep. • Diffusion in the matrix lattice is the creep-rate controlling process. • The microstructure instability is the main creep degradation process in T23 steel.

36 MATERIALS SCIENCE↗

Accelerated Stress Testing Results on Single-Channel and Multichannel Drivers (Final Report)

Drivers used to operate light-emitting diode (LED) loads form an integral part of the solid-state lighting (SSL) system. While understanding of LED failure modes such as luminous flux depreciation and chromaticity shifts has increased greatly over the past five years, there is still much uncertainty about general failure modes in SSL drivers due to the almost infinite variety of driver typologies. This report, which is the third in a series of three reports on driver robustness, summarizes overall findings from up to 7,500 hours of accelerated stress testing (AST) on two-stage SSL drivers that could be used to operate troffers and similar fixtures. The earlier reports in this series provided initial AST results for both single-channel and multichannel drivers and an interim update on the performance of multichannel drivers in AST.

42 ENGINEERING↗

DEVELOPMENT OF THE LARGE-BORE POWDER GUN FOR THE NEVADA TEST SITE

Plate-impact experiments on single stage guns provide very planar loading conditions suitable for studying complex phenomena such as phase transitions and material strength, and provide important data useful for constraining and validating predictive models. The objective of the current work was to develop a large-bore (3.5'' or greater) powder gun capable of accelerating projectiles to moderately high velocities (greater than 2.25 km/s) for impact experiments at Nevada Test Site. This gun will span a performance gap between existing gun facilities and provide a means of examining phenomena over a wide range of stresses and time-scales. Advantages of the large-bore gun include the capability to load multiple samples simultaneously, the use of large diameter samples that significantly extend the time duration of the experiment, and minimal tilt (no bow). This new capability required the development of a disposable confinement system that used an explosively driven closure method to prevent contamination from moving up into the gun system. Experimental results for both the gun system and the explosive valve are presented.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Zr-doped ceria additives for enhanced PEM fuel cell durability and radical scavenger stability

Doped ceria compounds demonstrate excellent radical scavenging abilities and are promising additives to improve the chemical durability of polymer electrolyte membrane (PEM) fuel cells. Here in this paper, Ce 0.85 Zr 0.15 O 2 (CZO) nanoparticles were incorporated into the cathode catalyst layers (CLs) of PEM fuel cells (based on Nafion XL membranes containing 6.0 μg cm -2 ion-exchanged Ce) at loadings of 10 and 55 μg cm -2 . When compared to a CZO-free baseline, CZO-containing membrane electrode assemblies (MEAs) demonstrated extended lifetimes during PEM chemical stability accelerated stress tests (ASTs), exhibiting reduced electrochemical gas crossover, open circuit voltage decay, and fluoride emission rates. The MEA with high CZO loading (55 μg cm -2 ) demonstrated performance losses, which are attributed to Ce poisoning of the PEM and CL ionomer regions, which is supported by X-ray fluorescence (XRF) analysis. In the MEA with the low CZO loading (10 μg cm -2 ), both the beginning of life (BOL) performance and the performance after 500 hours of ASTs were nearly identical to the BOL performance of the CZO-free baseline MEA. XRF analysis of the MEA with low CZO loading reveals that the BOL PEM Ce concentrations are preserved after 1408 hours of ASTs and that Ce contents in the cathode CL are not significant enough to reduce performance. Therefore, employing a highly effective radical scavenger such as CZO, at a loading of 10 μg cm -2 in the cathode CL, dramatically mitigates degradation effects, which improves MEA chemical durability and minimizes performance losses.

36 MATERIALS SCIENCE↗

The deformation and failure response of closed-cell PMDI foams subjected to dynamic impact loading

The present work aims to investigate the bulk deformation and failure response of closed-cell Polymeric Methylene Diphenyl Diisocyanate (PMDI) foams subjected to dynamic impact loading. First, foam specimens of different initial densities are examined and characterized in quasi-static loading conditions, where the deformation behavior of the samples is quantified in terms of the compressive elastic modulus and effective plastic Poisson's ratio. Then, the deformation response of the foam specimens subjected to direct impact loading is examined by taking into account the effects of material compressibility and inertia stresses developed during deformation, using high speed imaging in conjunction with 3D digital image correlation. The stress-strain response and the energy absorption as a function of strain rate and initial density are presented and the bulk failure mechanisms are discussed. As a result, it is observed that the initial density of the foam and the applied strain rates have a substantial influence on the strength, bulk failure mechanism and the energy dissipation characteristics of the foam specimens.

36 MATERIALS SCIENCE↗

Unified Stress-Strain Model for Plasticity to the Structural Instability

A unified model for the work hardening Θσ Θ(σ) and stress-strain σε σ(ε) behavior is presented that accounts for deformation under tensile loading, from the onset of yielding at the proportional limit up to the ultimate strength as defined at the structural instability. The origin of this approach is based on a negative exponential formulation for an asymptotic-curvilinear work-hardening model that accounts for the rapid strengthening of metals as well as the continuation of steady-state deformation to the instability.

36 MATERIALS SCIENCE↗

Assessment of structural, thermal, and mechanical properties of portlandite through molecular dynamics simulations

The structural, thermal, and mechanical properties of portlandite, the primary solid phase of ordinary hydrated cement paste, are investigated using the molecular dynamics method. To understand the effects of temperature on the structural properties of portlandite, the coefficients of thermal expansion of portlandite are determined in the current study and validated with what reported from the experimental tests. The atomic structure of portlandite equilibrated at various temperatures is then subjected to uniaxial tensile strains in the three orthogonal directions and the stress-strain curves are developed. Based on the obtained results, the effect of the direction of straining on the mechanical properties of portlandite is investigated in detail. Structural damage analysis is performed to reveal the failure mechanisms in different directions. The energies of the fractured surfaces are calculated in different directions and compared to those of the ideal surfaces available in the literature. The key mechanical properties, including tensile strength, Young's modulus, and fracture strain, are extracted from the stress-strain curves. The sensitivity of the obtained mechanical properties to temperature and strain rate is then explored in a systematic way. This leads to valuable information on how the structural and mechanical properties of portlandite are affected under various exposure conditions and loading rates. - Graphical abstract: Fracture mechanism of portlandite under uniaxial strain in the z-direction. - Highlights: • The structural, thermal, and mechanical properties of portlandite are investigated. • The coefficients of thermal expansion are determined. • The stress-strain relationships are studied in three orthogonal directions. • The effects of temperature and strain rate on mechanical properties are examined. • The plastic energy required for fracture in the crystalline structure is reported.

36 MATERIALS SCIENCE↗