Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STEELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

Understanding Microstructural Evolution During Rapid Heat Treatment of Microalloyed Steels Through Computational Modeling, Advanced Physical Simulation, and Multiscale Characterization Techniques

An AISI 1045 steel modified with vanadium (V) and niobium (Nb) was studied to evaluate microstructural conditioning prior to and throughout a rapid heat treat process. In order to accomplish this, both computational and physical simulation techniques have been employed with the goal of assessing the microstructural evolution in a medium-carbon bar steel during the rapid austenitization and quenching procedures involved in an induction hardening process. The appropriate thermal profiles for induction hardening were obtained through finite element modeling using Flux 2D software. Physical simulations of the induction hardening process were carried out using a Gleeble{sup ®} 3500. Analysis of prior austenite grain size is complemented by observation of nanoscale carbonitride precipitation via transmission electron microscopy, scanning transmission electron microscopy, and high-energy synchrotron small-angle x-ray scattering. Through a combination of characterization techniques, this study presents a deeper understanding of nano- and microstructural changes occurring in a microalloyed steel during an induction hardening process.

36 MATERIALS SCIENCE↗

Effect of Heat Input on M-A Constituent and Toughness of Coarse Grain Heat-Affected Zone in an X100 Pipeline Steel

The joining of 14.8 mm thick pipeline steels was achieved with developments in high-power fiber laser by laser welding or hybrid laser arc welding. However, there were few studies on the effects of single-pass welding heat input on the M-A component and impact toughness of the heat-affected zone. In this study, single-pass welding thermal cycle was performed on Gleeble 3800 thermal simulation tester; the effect of heat input on microstructure, M-A constituent, hardness, toughness and corrosion resistance of coarse-grained heat-affected zone of X100 pipeline steel was studied. The results showed: The microstructure was lath martensite with a heat input of less than 8 kJ/cm. When the heat input was 26-36 kJ/cm, the microstructure was granular bainite. The heat input had not obvious effect on hardness (only 16% hardness reduction in this heat input arrange). However, the impact toughness was strongly influenced by heat input, with an 88% hardness reduction compared to base metal, due to M-A constituent and prior austenite grain size. Few finer M-A constituent dispersing in austenite was obtained instead of necklace-like M-A constituent at the prior austenite grain boundary when the welding heat input was less than 15 kJ/cm, which was beneficial to improve the impact toughness and corrosion resistance of welded joints of X100 pipeline steels.

36 MATERIALS SCIENCE↗

Corrosion of 907 Steel Influenced by Sulfate-Reducing Bacteria

The effect of sulfate-reducing bacteria (SRB) on the corrosion of 907 steel was investigated. Results demonstrated that the chemical composition of corrosion products, the corrosion rate, and corrosion type were altered due to the adherence of SRB and the subsequent formation of biofilm on the 907 steel surface. Different from the case in sterile medium that ferrous oxides predominated in the corrosion products, ferrous sulfide was an important component in SRB-containing medium. Meanwhile, corrosion of 907 steel was enhanced by SRB, and the corrosion rate was dependent on their metabolic activity, which increased, stabilized, and decreased in the exponential growth, death, and residual phases, respectively. Furthermore, the corrosion type was changed from uniform corrosion to localized corrosion with the introduction of SRB, and the development process was analyzed based on the current distribution map of wire beam electrodes. In sterile medium, the maximum current density decreased with the immersion time extended, and there were no significant anodic current peaks in the late period, while in SRB-containing medium, the ratio between cathodic areas and anodic areas was high in the exponential growth phase, and stable anodic sites formed gradually in death and residual phases, which facilitated the development of localized corrosion.

36 MATERIALS SCIENCE↗

Evolution of Crystallographic Structure of M{sub 23}C{sub 6} Carbide Under Thermal Aging of P91 Steel

The structural changes of P91 steel after different heat treatment and M{sub 23}C{sub 6} lattice expansion are well described by JMA kinetics law; however, the role of molybdenum on the M{sub 23}C{sub 6} lattice expansion is not clearly revealed. The aim of the present work is to investigate the solubility of molybdenum in M{sub 23}C{sub 6} lattice when iron or chromium atoms are replaced by molybdenum and to examine the effect of crystallographic structure changes on the mechanical properties of thermal aged P91 steel. Rietveld analysis of electrochemically extracted residues from the as-received and thermally aged at 600, 650 and 700 °C steel revealed that it is possible to measure and evaluate quantitatively the fraction of 8c crystallographic site occupation by molybdenum atoms of the M{sub 23}C{sub 6} lattice. It was shown that the value of the site occupation factor plotted in natural logarithmic scale increases linearly and obeys Johnson–Mehl–Avrami kinetic law, giving Avrami exponent n{sub avg} = 0.3356 and activation energy E = 272 kJ/mol. Hardness measurements of the aged samples indicate that the deterioration of properties is closely coherent to the growth of crystallite size.

36 MATERIALS SCIENCE↗

Corrosion Behavior of Laser-Brazed Surface Made by Joining of AA6082 and Galvanized Steel

In the present study, a galvanized steel and a AA6082 aluminum alloy sheet of 2 mm thick were weld-brazed by applying laser and using 2-mm-diameter solid Al-12% Si filler wire at 2.5 m/min wire feed rate and 2 m/min laser scan speed at varying laser power (4.0, 3.5, 3.0 kW) in flange configuration. The microstructural investigation of the laser weld-brazed joints revealed the presence of two-layered intermetallic compound at steel/braze seam interface. The corresponding x-ray diffraction analysis of the steel/braze seam interface showed the presence of Al-Fe-Si-based ternary intermetallic phases. SEM and EDS analysis of the braze seam revealed the presence of α-Al grains surrounded by Mg{sub 2}Si phase in the grain boundary region. Fine intermetallic layer was observed at lower heat-input condition. The corrosion performance of the brazed joints was studied with the help of immersion, salt spray, and electrochemical polarization tests in different electrolytes containing NaCl salt. Brazed joints experienced galvanic corrosion during immersed in corrosive media. From the salt spray test, it was revealed that galvanized steel was highly susceptible to corrosion compared to Al-rich phase. The polarization results showed a substantial change in corrosion resistance from steel interface to the brazed region due to the variation in microstructure. The samples brazed with low heat-input showed better corrosion resistance as compared to the joints made with high heat-input. Post-corrosion microstructure revealed intergranular corrosion at the brazed joint along with pit formation.

36 MATERIALS SCIENCE↗

Effect of Solution pH on Layered Double Hydroxide Formation on Electrogalvanized Steel Sheets

The effect of solution pH on layered double hydroxide (LDH) formation on electrogalvanized steel sheets (EG steel) was investigated in this study. EG steel with a Zn coating weight of 64 g/m{sup 2} was used as a substrate and was immersed in a 0.25 M Na{sub 2}Al{sub 2}O{sub 4}-based solution having several pH values to form a Zn-Al-based LDH conversion coating. After rinsing and drying, corrosion resistance was evaluated by EIS. It was found that corrosion resistance increased with increasing pH up to pH 12.6. However, above this pH, corrosion resistance tended to display a sharp decrease. To understand this trend, the conversion coating was characterized by FT-IR, XRD and GDOES. The conversion coating was found to consist mainly of Zn{sub 2}Al(OH){sub 6}(CO{sub 3}){sub 0.5}·xH{sub 2}O crystals (an LDH). The thickness of the conversion coating layer increased with increasing pH up to pH 12.4, but above this pH, its thickness tended to decrease due to the formation of ZnO. The reason for the dependence of corrosion resistance on solution pH is discussed from the viewpoints of the thickness and changes in the microstructure of the conversion coating layer, including its crystal size, density and uniformity, which could vary during the initial formation of ZnO at pH values above 12.6.

36 MATERIALS SCIENCE↗

A Study of Microstructure Evolution During Creep of 9Cr-1Mo Steel Using Ultrasonic and Hardness Measurements

In this work, microstructural changes during creep of 9Cr-1Mo steel were characterized using ultrasonic and hardness measurements. The creep testing of this steel was firstly performed at 873 K under the initial stresses of 160 and 175 MPa, respectively. Then, eight specimens under each stress level were prepared by the interrupted tests to simulate various creep states. Subsequently, two parameters of ultrasonic attenuation and velocity were introduced by the ultrasonic testing. Experiment results showed that regardless of the stresses, the ultrasonic attenuation experiences a peak at about 20% of the creep rupture time and a minimum value at about 50%, showing a strong correlation between ultrasonic attenuation and the creep life fraction. In addition to a slight increase during the primary creep, the ultrasonic velocity exhibits a significant change during the tertiary creep. Based on the analysis of microstructure changes, it indicated that the ultrasonic attenuation is significantly sensitive to the dynamic changes of the dislocation. In contrast, the velocity is mainly related to the evolution of precipitates. The Vickers hardness decreases monotonously during the creep process and presents a linear relation with the inverse of average diameter of M{sub 23}C{sub 6} carbides during the secondary and tertiary creep. Accordingly, it suggested that the present ultrasonic and hardness measurements provided a convenient tool to evaluate the microstructure evolution during creep degradation of heat-resistant steels.

36 MATERIALS SCIENCE↗

Effects of Multiple Laser Peening impacts on Mechanical Properties and Microstructure Evolution of 40CrNiMo Steel

The effects of multiple laser peening impacts on mechanical properties and microstructure of 40CrNiMo steel were investigated. The surface residual stress and microhardness of the samples with different treatments were measured. The surface morphologies, tensile behavior and microstructure of the samples before and after laser peening were compared and analyzed. The experimental results showed that laser peening, especially multiple laser peening impacts has significant effects on the microhardness, residual stress and microstructure of 40CrNiMo steel. The surface roughness and the depth of the pit increased with increasing the impact times. After 3 laser peening impacts, the surface microhardness, compressive residual stress, the strength and ductility were significantly improved. Meanwhile, some microstructures, such as sub-grains, the precipitation of carbide and dislocations were also induced in the surface layer. Additionally, the microscopic strengthening mechanism of multiple laser peening impacts on the mechanical properties of 40CrNiMo steel was analyzed in detail.

36 MATERIALS SCIENCE↗

Wear and Corrosion Resistances of Active Screen Plasma-Nitrided Duplex Stainless Steels

Two grades of duplex stainless steel, SAF 2205 and SAF 2507, were nitrided using an active screen plasma process carried out at 380 °C for 10 h and were characterized in terms of microstructure and hardness. Wear resistance was assessed by means of linear scratch tests, using loads below and above the critical load. Potentiodynamic polarization was used to analyze corrosion behavior in 0.6 M NaCl solution. X-ray diffractometry showed expanded austenite formation in all nitrided samples. The super duplex steel SAF 2507 showed much better scratch resistance, with low friction coefficient and greater toughness, as judged by the pattern of superficial cracks when it was tested above the critical load. The corrosion behavior of steels was also different, mainly in the active region, and nitriding had a more beneficial effect upon SAF 2507. The potential relative to the transpassive region was practically unaffected by the nitriding.

36 MATERIALS SCIENCE↗

High-Cycle Fatigue Behavior of Vacuum-Carburized 20Cr2Ni4 Steel with Different Case Depths

High-cycle fatigue behavior of vacuum-carburized 20Cr2Ni4 steel with three different case depths was studied by using rotating bending fatigue test. The results show that fatigue strength exhibits an increase–decrease pattern with increasing effective case dept, which is regarded to be mainly due to the unavoidable change in other parameters such as residual stress and grain size in case layer besides case depth. The present data and data in the available literature suggest that a dimensionless parameter of relative case depth is more appropriate to reflect the influence of case depth on fatigue strength. Further fracture surface analysis revealed that the fatigue failure was dominated by surface crack initiation mainly due to the extremely high cleanness of the tested steel with inclusion control. It is thus concluded that both relative case depth and other parameters should be comprehensively considered in obtaining optimized fatigue performance of vacuum-carburized steel.

36 MATERIALS SCIENCE↗

Microstructure Optimization and Cracking Control of Additive Manufactured Bainite Steel by Gas Metal Arc Welding Technology

In this work, bainite steel thin wall was prepared by additive manufacturing (AM) with an in situ isothermal transformation at 300 °C. The microstructures were analyzed by scanning electron microscopy (SEM), x-ray diffraction (XRD) and transmission electron microscopy (TEM). The mechanical properties of the AM samples were measured by microhardness testing and tensile testing. The results show that the bainite steel thin wall is free from cracks and each layer has a good bond with preceding one. The bainite steel thin wall displays consistent mechanical properties. The formation of the bainite microstructure improves the toughness of the thin wall and reduces the embrittlement caused by dendritic segregation.

36 MATERIALS SCIENCE↗

Influence of Austenitizing Temperature on the Microstructure and Mechanical Properties of an Fe-Cr-Ni-Mo-Ti Maraging Stainless Steel

The influence of austenitizing temperature on the microstructure and mechanical properties of an Fe-Cr-Ni-Mo-Ti maraging stainless steel was investigated. The grain size, Laves phase, and retained austenite in steels given different solution treatments were observed using optical microscopy, scanning electron microscopy, and x-ray diffraction. Relationships with mechanical properties were measured by tensile testing. The grain growth rate was relatively slow at temperatures of 800-1000 °C then rapidly increased at higher temperatures. Low-temperature austenitization augmented the retention of austenite, the fraction of which decreased with an increase in austenitizing temperature. The Laves phases, which precipitated in austenite during austenitization at 800-900 °C, were preserved after quenching. The solution treatment had a significant effect on the final tensile properties of the steel after aging, due to the presence of retained austenite and Laves phase reducing its strength.

36 MATERIALS SCIENCE↗

Very High-Cycle Fatigue Properties and Residual Stress Relaxation of Micro-shot-Peened EA4T Axle Steel

In this paper, EA4T alloy railway axle steel was shot peened with steel balls and ceramic balls with a diameter of 50 μm, and 10{sup 9}-cycle fatigue tests of unpeened and peened specimens were carried out. The fatigue properties and the surface compression residual stress relaxation processes were investigated. The results of surface fracture observation indicated that all the cracks initiated from the surface, and both peened and unpeened specimens have conventional fatigue limits in the very high-cycle fatigue regime. Moreover, compared with unpeened (UP) specimens, the fatigue limits were improved by 31 and 28% for ceramic shot-peened (CSP) and steel shot-peened (SSP) specimens, respectively. The improvement of fatigue limit is related to the surface compressive residual stresses (SCRS) and the surface-hardened layer. The SCRS and full-width half-maximum (FWHM) values during the relaxation processes have been analyzed. At stress amplitudes lower than the cyclic yield strength, the residual stress of SSP specimens relaxed quickly in the first loading cycle and then remained stable, while the residual stress of CSP specimens relaxed quickly in the first loading cycle and relaxed slowly afterward, then remained stable. For all SSP and CSP specimens with applied stress amplitudes larger than the cyclic yield strength, the residual stress relaxed quickly in the initial cycles, and then remained stable after the first loading cycle.

36 MATERIALS SCIENCE↗

Strain-Rate Effect and Constitutive Models for Q550 High-Strength Structural Steel

High-strength structural steel is the tendency in modern construction practice. In this study, quasi-static tension tests and dynamic tests for Q550 with strain rate from 0.00025 to 3831 s{sup −1} were conducted. The results showed that Q550 is dependent on the strain rate, keeping the flow stress increased as the strain rate increases, while Q550 has lower strain-rate sensitivity of flow stress than that of normal mild steel. Based on the experimental data, a proper constant for the key parameter, C, in Johnson–Cook model (J–C) was suggested. Then, a modified J–C model based on a rate-dependent parameter C( ε-dot ) was recommended to consider the influence of strain-rate effect. New constants of D and p governing the dynamic response of steel in the Cowper–Symonds (C–S) model were also suggested. The C–S model and J–C models with suggested constants provided in the paper were proven to have acceptable prediction accuracy for the dynamic increase factor of Q550. These results may be applied to study the dynamical properties of Q550 and related structural components for future engineering applications.

36 MATERIALS SCIENCE↗

Corrosion of Mild Steel Buried Underground for 3 Years in Different Soils of Varying Textures

The effect of moisture content and soil texture on the corrosion behavior of mild steel coupons buried for 3 years in different soils was estimated from weight loss measurements and electrochemical techniques such as Tafel plots and electrochemical impedance spectroscopy. The results showed that the rate of corrosion and intensity of corrosion attack significantly depend on the soil’s moisture content and on the soil type. Corrosion was found to be severe in clayey soil compared to that in mixed and sandy soils. Morphological analysis of the corroded specimens performed using optical microscopy and scanning electron microscopy showed the presence of amorphous oxides and low-intense crystalline phases of goethite and hematite on the surface of the mild steel coupons, indicating only the initial stage of corrosion. It is concluded from this study that mild steel undergoes only less intense surface-level corrosion in 3 years when buried underground.

36 MATERIALS SCIENCE↗

Effect of Niobium on the Secondary Precipitates and Tempering Resistance of Spray-Formed M3:2 High-Speed Steel

The precipitation of secondary carbides in spray-formed M3:2 high-speed steels with or without 2% niobium (Nb) addition during overtempering at 600 °C was characterized, and the carbides were identified in detail using transmission electron microscopy. Strengthening in the peak-hardened state is due to coherent precipitates of types MC and M{sub 2}C. During overtempering, the hardness of M3:2 steel greatly decreases due to M{sub 2}C coarsening with the precipitation of M{sub 3}C carbide, whereas the very fine and dense nature of the M{sub 2}C precipitates is responsible for the remarkable long-time strength exhibited by the Nb-containing steel. The MC precipitates, however, are fairly stable. The addition of Nb results in substantial dissolution of Mo and Cr into the matrix prior to tempering, which refines the secondary M{sub 2}C precipitate dispersion and delays overaging reactions; therefore, superior tempering resistance can be obtained.

36 MATERIALS SCIENCE↗

Predictive Reactor Pressure Vessel Steel Irradiation Embrittlement Models: Issues and Opportunities

Nuclear plant life extension to 80 years will require accurate predictions of neutron irradiation-induced increases in the ductile-brittle transition temperature ( T) of reactor pressure vessel (RPV) steels at high fluence conditions that are far outside the existing database. Remarkable progress in mechanistic understanding of irradiation embrittlement has led to physically motivated T correlation models that provide excellent statistical fi ts to the existing surveillance database. However, an important challenge is developing advanced embrittlement models for low fl ux-high fl uence conditions pertinent to extended life. These new models must also provide better treatment of key variables and variable combinations and account for possible delayed formation of late blooming phases in low copper steels. Other issues include uncertainties in the compositions of actual vessel steels, methods to predict T attenuation away from the reactor core, verifi cation of the master curve method to directly measure the fracture toughness with small specimens and predicting T for vessel annealing remediation and re-irradiation cycles.

36 MATERIALS SCIENCE↗

Data-Driven Surrogate Modeling with Microstructure-Sensitivity of Viscoplastic Creep in Grade 91 Steel

Abstract To support the development of advanced steel alloys tailored to withstand extreme conditions, it is imperative to account for the mechanical performance of components, while considering the influence of local microstructure on the macroscopic response. To this end, this study focuses on the development of microstructure-sensitive constitutive models for the mechanical response of Grade 91 steel exposed to extreme thermo-mechanical environments. Polynomial chaos expansion (PCE) surrogates are used to emulate high-fidelity polycrystal simulations of the viscoplastic response of Grade 91 steel as a function of the microstructure fingerprint (e.g., dislocations and precipitates). To cover a wide temperature–stress domain, two separate PCE surrogates—one that captures softening and the other that captures hardening behavior—are combined using another (sparse) Gaussian process regression model. The resulting constitutive creep surrogate model is integrated within the MOOSE finite element framework to simulate the intricate effects of microstructure, in particular MX-phase precipitates, on a component with a graded microstructure. Surrogate sensitivity analysis is applied to quantify the relevant impact of spatially varying microstructure on the creep response in a test-case involving a Grade 91 alloy with a prototypical weld.

36 MATERIALS SCIENCE↗