Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SPUTTERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

Electrical spin injection into InGaAs/GaAs quantum wells: A comparison between MgO tunnel barriers grown by sputtering and molecular beam epitaxy methods

An efficient electrical spin injection into an InGaAs/GaAs quantum well light emitting diode is demonstrated thanks to a CoFeB/MgO spin injector. The textured MgO tunnel barrier is fabricated by two different techniques: sputtering and molecular beam epitaxy. The maximal spin injection efficiency is comparable for both methods. Additionally, the effect of annealing is also investigated for the two types of samples. Both samples show the same trend: an increase of the electroluminescence circular polarization (P{sub c}) with the increase of annealing temperature, followed by a saturation of P{sub c} beyond 350 °C annealing. Since the increase of P{sub c} starts well below the crystallization temperature of the full CoFeB bulk layer, this trend could be mainly due to an improvement of chemical structure at the top CoFeB/MgO interface. This study reveals that the control of CoFeB/MgO interface is essential for an optimal spin injection into semiconductor.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Strength, stiffness, and microstructure of Cu(In,Ga)Se{sub 2} thin films deposited via sputtering and co-evaporation

This work examines Cu(In,Ga)Se{sub 2} thin films fabricated by (1) selenization of pre-sputtered Cu-In-Ga and (2) co-evaporation of each constituent. The efficiency disparity between films deposited via these two methods is linked to differences in morphology and microstructure. Atomic force microscopy and scanning electron microscopy show that selenized films have rougher surfaces and poor adhesion to molybdenum back contact. Transmission electron microscopy and electron energy loss spectroscopy revealed multiple voids near the Mo layer in selenized films and a depletion of Na and Se around the voids. Residual stresses in co-evaporated films were found to be ∼1.23 GPa using wafer curvature measurements. Uniaxial compression experiments on 500 nm-diameter nanopillars carved out from co-evaporated films revealed the elastic modulus of 70.4 ± 6.5 GPa. Hertzian contact model applied to nanoindentation data on selenized films revealed the indentation modulus of 68.9 ± 12.4 GPa, which is in agreement with previous reports. This equivalence of the elastic moduli suggests that microstructural differences manifest themselves after the yield point. Typical plastic behavior with two distinct failure modes is observed in the extracted stress-strain results, with the yield strength of 640.9 ± 13.7 MPa for pillars that failed by shearing and 1100.8 ± 77.8 MPa for pillars that failed by shattering.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Nanosecond laser-induced damage at different initial temperatures of Ta{sub 2}O{sub 5} films prepared by dual ion beam sputtering

Ta{sub 2}O{sub 5} films were deposited by dual ion beam sputtering method. The nanosecond laser-induced damage threshold (LIDT) at different initial temperatures and time of the films was investigated by an in situ high temperature laser-induced damage testing platform. It was shown that, when the initial temperature increased from 298 K to 383 K, the LIDT at 1064 nm and 12 ns significantly decreased by nearly 14%. Then the LIDT at 1064 nm and 12 ns decreased slower with the same temperature increment. Different damage morphologies were found at different initial temperatures. At low initial temperatures, it was the defects-isolated damage while at high initial temperatures it was the defects-combined damage. The theoretical calculations based on the defect-induced damage model revealed that both the significant increase of the highest temperature and the duration contributed to the different damage morphologies. With the initial temperature being increased, the thermal-stress coupling damage mechanism transformed gradually to the thermal dominant damage mechanism.

36 MATERIALS SCIENCE↗

Correlation of photothermal conversion on the photo-induced deformation of amorphous carbon nitride films prepared by reactive sputtering

The photo-induced deformation of hydrogen-free amorphous carbon nitride (a-CN{sub x}) films was investigated under visible-light illumination. The films gave rise to photothermal conversion by irradiation. In this study, we investigated the effects of thermal energy generated by irradiation on the deformation of a-CN{sub x}/ultrathin substrate bimorph specimens. The films were prepared on both ultrathin Si and SiO{sub 2} substrates by reactive radio-frequency magnetron sputtering from a graphite target in the presence of pure nitrogen gas. The temperature of the film on the SiO{sub 2} substrate increased as the optical band-gap of the a-CN{sub x} was decreased. For the film on Si, the temperature remained constant. The deformation degree of the films on Si and SiO{sub 2} substrates were approximately the same. Thus, the deformation of a-CN{sub x} films primarily induced by photon energy directly.

36 MATERIALS SCIENCE↗

Determination of the density of the defect states in Hf{sub 0.5}Zr{sub 0.5}O{sub 2} high-k film Deposited by using rf-magnetron sputtering technique

A memory structure Pt/Al{sub 2}O{sub 3}/Hf{sub 0.5}Zr{sub 0.5}O{sub 2}/Al{sub 2}O{sub 3}/p-Si was fabricated by using atomic layer deposition and rf-magnetron sputtering techniques, and its microstructure has been investigated by using the high resolution transmission electron microscopy (HRTEM). By measuring the applied gate voltage dependence of the capacitance for the memory structure, the planar density of the trapped charges in Hf{sub 0.5}Zr{sub 0.5}O{sub 2} high-k film was estimated as 6.63 × 10{sup 12} cm{sup −2}, indicating a body defect density of larger than 2.21 × 10{sup 19} cm{sup −3}. It is observed that the post-annealing in N{sub 2} can reduces the defect density in Hf{sub 0.5}Zr{sub 0.5}O{sub 2} film, which was ascribed to the occupancy of oxygen vacancies by nitrogen atoms.

36 MATERIALS SCIENCE↗

In-situ spectroscopic ellipsometry and structural study of HfO{sub 2} thin films deposited by radio frequency magnetron sputtering

We have investigated the reduction of unwanted interfacial SiO{sub 2} layer at HfO{sub 2}/Si interface brought about by the deposition of thin Hf metal buffer layer on Si substrate prior to the deposition of HfO{sub 2} thin films for possible direct contact between HfO{sub 2} thin film and Si substrate, necessary for the future generation devices based on high-κ HfO{sub 2} gate dielectrics. Reactive rf magnetron sputtering system along with the attached in-situ spectroscopic ellipsometry (SE) was used to predeposit Hf metal buffer layer as well as to grow HfO{sub 2} thin films and also to undertake the in-situ characterization of the high-κ HfO{sub 2} thin films deposited on n-type 〈100〉 crystalline silicon substrate. The formation of the unwanted interfacial SiO{sub 2} layer and its reduction due to the predeposited Hf metal buffer layer as well as the depth profiling and also structure of HfO{sub 2} thin films were investigated by in-situ SE, Fourier Transform Infrared spectroscopy, and Grazing Incidence X-ray Diffraction. The study demonstrates that the predeposited Hf metal buffer layer has played a crucial role in eliminating the formation of unwanted interfacial layer and that the deposited high-κ HfO{sub 2} thin films are crystalline although they were deposited at room temperature.

36 MATERIALS SCIENCE↗

Preparation of a heteroepitaxial La{sub x}Sr{sub y}Mn{sub z}O{sub 3}/BiFeO{sub 3} bilayer by r.f. magnetron sputtering with various oxygen gas flow ratios

BiFeO{sub 3} (BFO) and La{sub x}Sr{sub y}Mn{sub z}O{sub 3} (LSMO) films were epitaxially grown on SrTiO{sub 3} (100) substrates by r.f. magnetron sputtering with various oxygen gas flow ratios (F{sub O2}). Compositional ratios of each atom in both of BFO and LSMO could be controlled kept to around 10 at.% by changing F{sub O2}. Adjusting the compositional ratio to La{sub 0.35}Sr{sub 0.15}Mn{sub 0.5}O{sub 3} not only increase T{sub c} of LSMO but also produces sufficient oxygen to form a perovskite lattice. For an LSMO/BFO heterostructure, detailed observation by cross sectional transmission electron microscopy (TEM) revealed that the lattice of rhombohedral (SG: R-3c) LSMO was shrank by a clamping effect from the SrTiO{sub 3} substrates, and then the BFO was grown in two layers: (i) an interfacial BFO layer (7 nm thick) with evenly shrunk a-axis and c-axis, and (ii) an upper BFO layer (25 nm thick) expanded along the c-axis. Neither misfit strain nor dislocations appeared at the interface between the shrunken BFO and LSMO layers, and these heterostructures did not show exchange bias. These results suggest that BFO is suitable for a tunneling barrier combine with LSMO electrode.

36 MATERIALS SCIENCE↗

Effect of oxygen incorporation on the structure and elasticity of Ti-Al-O-N coatings synthesized by cathodic arc and high power pulsed magnetron sputtering

Ti-Al-O-N coatings were synthesized by cathodic arc and high power pulsed magnetron sputtering. The chemical composition of the coatings was determined by means of elastic recoil detection analysis and energy dispersive X-ray spectroscopy. The effect of oxygen incorporation on the stress-free lattice parameters and Young's moduli of Ti-Al-O-N coatings was investigated by X-ray diffraction and nanoindentation, respectively. As nitrogen is substituted by oxygen, implications for the charge balance may be expected. A reduction in equilibrium volume with increasing O concentration is identified by X-ray diffraction and density functional theory calculations of Ti-Al-O-N supercells reveal the concomitant formation of metal vacancies. Hence, the oxygen incorporation-induced formation of metal vacancies enables charge balancing. Furthermore, nanoindentation experiments reveal a decrease in elastic modulus with increasing O concentration. Based on ab initio data, two causes can be identified for this: First, the metal vacancy-induced reduction in elasticity; and second, the formation of, compared to the corresponding metal nitride bonds, relatively weak Ti-O and Al-O bonds.

36 MATERIALS SCIENCE↗

Dependence of dynamic magnetization and magneto-transport properties of FeAlSi films with oblique sputtering studied via spin rectification effect

FeAlSi (Sendust) is known to possess excellent soft magnetic properties comparable to traditional soft magnetic alloys such as NiFe (Permalloy), while having a relatively higher resistance for lower eddy current losses. However, their dynamic magnetic and magneto-transport properties are not well-studied. Via the spin rectification effect, we electrically characterize a series of obliquely sputtered FeAlSi films at ferromagnetic resonance. The variations of the anisotropy fields and damping with oblique angle are extracted and discussed. In particular, two-magnon scattering is found to dominate the damping behavior at high oblique angles. An analysis of the results shows large anomalous Hall effect and anisotropic magneto-resistance across all samples, which decreases sharply with increasing oblique incidence.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Research Update: Reactively sputtered nanometer-thin ZrN film as a diffusion barrier between Al and boron layers for radiation detector applications

In this paper, optimization of the process flow for PureB detectors is investigated. Diffusion barrier layers between a boron layer and the aluminum interconnect can be used to enhance the performance and visual appearance of radiation detectors. Few nanometers-thin Zirconium Nitride (ZrN) layer deposited by reactive sputtering in a mixture of Ar/N{sub 2}, is identified as a reliable diffusion barrier with better fabrication process compatibility than others. The barrier properties of this layer have been tested for different boron layers deposited at low and high temperatures with extensive optical microscopy analyses, electron beam induced current, SEM, and electrical measurements. This study demonstrated that spiking behavior of pure Al on Si can be prevented by the thin ZrN layer thus improving the performance of the radiation detectors fabricated using boron layer.

36 MATERIALS SCIENCE↗

Studies on Nd{sub x}In{sub 1−x}O{sub 3} semiconducting thin films prepared by rf magnetron sputtering

Neodymium-substituted indium oxide (Nd{sub x}In{sub 1−x}O{sub 3}, NIO) semiconducting thin films fabricated by rf sputtering were investigated. It was found that the incorporation of Nd atoms would lead to broadening the optical band gap, suppressing the grain growth, and reducing the free carrier concentration. The field-effect transistors with different NIO (5%, 15%, and 25% Nd concentration of the targets) channel layers exhibited similar electrical stability under positive gate-bias-stress, but the ones with 15% and 25% Nd concentration displayed much better stability under negative gate-bias-stress. Detailed studies showed that the content of |Nd3d{sub 5/2}{sup 5}4f{sup 4}O2p{sup −1}> electron configuration decreased as the Nd concentration increased, resulting in the reduction of holes during negative-bias-stress. And the reduction of the |Nd3d{sub 5/2}{sup 5}4f{sup 4}O2p{sup −1}> content as the Nd concentration increased was ascribed to less overlap between the metal and ligand orbitals arose from large lattice expansion.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Studies on optoelectronic properties of DC reactive magnetron sputtered chromium doped CdO thin films

Cr doped CdO thin films were deposited on glass substrates by DC reactive magnetron sputtering method and subsequently annealed from 200 °C to 500 °C. X-ray diffraction analysis showed that the films exhibit (1 1 1) preferred orientation. The optical transmittance of the films increases from 64% to 88% with increasing annealing temperature. The optical band gap values were found to be decreased from 2.77 to 2.65 eV with the increase of annealing temperature. The decrease in optical band gap energy with increasing annealing temperature can be attributed to improvement in the crystallinity of the films and may also be due to quantum confinement effect. A minimum resistivity of 2.23 × 10{sup −4} Ω.cm and sheet resistance of 6.3 Ω/sq is obtained for Cr doped CdO film annealed at 500 °C.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structural and optical properties of DC reactive magnetron sputtered zinc aluminum oxide thin films

Highly transparent conductive Zinc Aluminum Oxide (ZAO) thin films have been deposited on glass substrates using DC reactive magnetron sputtering method. The thin films were deposited at 200 °C and post-deposition annealing from 15 to 90 min. XRD patterns of ZAO films exhibit only (0 0 2) diffraction peak, indicating that they have c-axis preferred orientation perpendicular to the substrate. Scanning electron microscopy (SEM) is used to study the surface morphology of the films. The grain size obtained from SEM images of ZAO thin films are found to be in the range of 20 - 26 nm. The minimum resistivity of 1.74 × 10{sup −4} Ω cm and an average transmittance of 92% are obtained for the thin film post annealed for 30 min. The optical band gap of ZAO thin films increased from 3.49 to 3.60 eV with the increase of annealing time due to Burstein-Moss effect. The optical constants refractive index (n) and extinction coefficient (k) were also determined from the optical transmission spectra.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Characterization on RF magnetron sputtered niobium pentoxide thin films

Niobium pentoxide (Nb{sub 2}O{sub 5}) thin films with amorphous nature were deposited on microscopic glass substrates at 100°C by rf magnetron sputtering technique. The effect of rf power on the structural, morphological, optical, and vibrational properties of Nb{sub 2}O{sub 5} films have been investigated. Optical study shows the maximum average transmittance of about 87% and the optical energy band gap (indirect allowed) changes between 3.70 eV and 3.47 eV. AFM result indicates the smooth surface nature of the samples. Photoluminescence measurement showed the better optical quality of the deposited films. Raman spectra show the LO-TO splitting of Nb-O stretching of Nb{sub 2}O{sub 5} films.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Physical properties of Al{sub x}In{sub 1–x}N thin film alloys sputtered at low temperature

In this paper, we report on the structural, optical, and electrical properties of a wide compositional range of Al{sub x}In{sub 1–x}N thin layers deposited on glass and polyethylene terephthalate substrates. Al{sub x}In{sub 1–x}N layers of controlled composition were obtained by a simple reactive magnetron co-sputtering protocol, using a single aluminium target with indium insets, by varying the Al/In target surface area ratio, and the composition of the deposition atmosphere. The relevant physical properties were investigated and discussed. It is shown that the texture of the thin films is dependent on the cation ratio, while the bowing parameters of lattice constants and band gap values are larger than those of epitaxial layers.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Cyclic voltammetry on sputter-deposited films of electrochromic Ni oxide: Power-law decay of the charge density exchange

Ni-oxide-based thin films were produced by reactive direct-current magnetron sputtering and were characterized by X-ray diffraction and Rutherford backscattering spectroscopy. Intercalation of Li{sup +} ions was accomplished by cyclic voltammetry (CV) in an electrolyte of LiClO{sub 4} in propylene carbonate, and electrochromism was documented by spectrophotometry. The charge density exchange, and hence the optical modulation span, decayed gradually upon repeated cycling. This phenomenon was accurately described by an empirical power law, which was valid for at least 10{sup 4} cycles when the applied voltage was limited to 4.1 V vs Li/Li{sup +}. Our results allow lifetime assessments for one of the essential components in an electrochromic device such as a “smart window” for energy-efficient buildings.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

High quality boron carbon nitride/ZnO-nanorods p-n heterojunctions based on magnetron sputtered boron carbon nitride films

Boron carbon nitride (BCN) films were synthesized on Si (100) and fused silica substrates by radio-frequency magnetron sputtering from a B{sub 4}C target in an Ar/N{sub 2} gas mixture. The BCN films were amorphous, and they exhibited an optical band gap of ∼1.0 eV and p-type conductivity. The BCN films were over-coated with ZnO nanorod arrays using hydrothermal synthesis to form BCN/ZnO-nanorods p-n heterojunctions, exhibiting a rectification ratio of 1500 at bias voltages of ±5 V.

36 MATERIALS SCIENCE↗

Design and development of an in-line sputtering system and process development of thin film multilayer neutron supermirrors

Neutron supermirrors and supermirror polarizers are thin film multilayer based devices which are used for reflecting and polarizing neutrons in various neutron based experiments. In the present communication, the in-house development of a 9 m long in-line dc sputtering system has been described which is suitable for deposition of neutron supermirrors on large size (1500 mm × 150 mm) substrates and in large numbers. The optimisation process of deposition of Co and Ti thin film, Co/Ti periodic multilayers, and a-periodic supermirrors have also been described. The system has been used to deposit thin film multilayer supermirror polarizers which show high reflectivity up to a reasonably large critical wavevector transfer of ∼0.06 Å{sup −1} (corresponding to m = 2.5, i.e., 2.5 times critical wavevector transfer of natural Ni). The computer code for designing these supermirrors has also been developed in-house.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗