Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RACKS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59
All sourcesNASA NTRSDOE OSTI
DOE OSTI2017

Impact of gate geometry on ionic liquid gated ionotronic systems

Ionic liquid electrolytes are gaining widespread application as a gate dielectric used to control ion transport in functional materials. This letter systematically examines the important influence that device geometry in standard “side gate” 3-terminal geometries plays in device performance of a well-known oxygen ion conductor. We show that the most influential component of device design is the ratio between the area of the gate electrode and the active channel, while the spacing between these components and their individual shapes has a negligible contribution. Finally, these findings provide much needed guidance in device design intended for ionotronic gating with ionic liquids.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Multi frame synchrotron radiography of pulsed power driven underwater single wire explosions

We present herein the first use of synchrotron-based phase contrast radiography to study pulsed-power driven high energy density physics experiments. Underwater electrical wire explosions have become of interest to the wider physics community due to their ability to study material properties at extreme conditions and efficiently couple stored electrical energy into intense shock waves in water. The latter can be shaped to provide convergent implosions, resulting in very high pressures (1-10 Mbar) produced on relatively small pulsed power facilities (100s of kA-MA). Multiple experiments have explored single-wire explosions in water, hoping to understand the underlying physics and better optimize this energy transfer process; however, diagnostics can be limited. Optical imaging diagnostics are usually obscured by the shock wave itself; and until now, diode-based X-ray radiography has been of relatively low resolution and rather a broad x-ray energy spectrum. Utilising phase contrast imaging capabilities of the ID19 beamline at the European Synchrotron Radiation Facility, we were able to image both the exploding wire and the shock wave. Probing radiation of 20-50 keV radiographed 200 μm tungsten and copper wires, in ~2-cm diameter water cylinders with resolutions of 8 μm and 32 μm. The wires were exploded by a ~30-kA, 500-ns compact pulser, and 128 radiographs, each with a 100-ps X-ray pulse exposure, spaced at 704 ns apart were taken in each experiment. Abel inversion was used to obtain the density profile of the wires, and the results are compared to two dimensional hydrodynamic and one dimensional magnetohydrodynamic simulations.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2019

Use of synchrotron-based radiography to diagnose pulsed power driven wire explosion experiments

We describe the first use of synchrotron radiation to probe pulsed power driven high energy density physics (HEDP) experiments. Multi-frame x-ray radiography with interframe spacing of 704 ns and temporal resolution of < 100 ps was used to diagnose the electrical explosion of different wire configurations in water including single copper and tungsten wires, parallel copper wire pairs and copper x-pinches. Such experiments are of great interest to a variety of areas including equation of state studies and high pressure materials research, but the optical diagnostics that are usually employed in these experiments are unable to probe areas behind the shock wave generated in the water, as well as the internal structure of the exploding material. The x-ray radiography presented here, performed at beamline ID19 at ESRF, was able to image both sides of the shock to a resolution of up to 8 µm, and phase contrast imaging (PCI) allowed fine details of the wire structure during the current driven explosion and the shock waves to be clearly observed. These results demonstrate the feasibility of pulsed power operated in conjunction with synchrotron facilities, as well as an effective technique in the study of shock waves and wire explosion dynamics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2019

Synchrotron based X-ray radiography of convergent shock waves driven by underwater electrical explosion of a cylindrical wire array

We present x-ray radiography images showing the propagation of shock waves generated by electrical explosion of a cylindrical arrangement of wires in water driven by pulsed power. In previous experiments [S. N. Bland et al., Phys. Plasmas 24, 082702 (2017)] the merger of shock waves from adjacent wires has produced a highly symmetrical, cylindrical shock wave converging on the axis, where it is expected to produce a high density, strongly coupled plasma ideal for warm dense matter research. However, diagnostic limitations have meant that much of the dynamics of the system have been inferred from the position of the front of the cylindrical shock and timing/spectra of light emitted from the axis. Here we present synchrotron-based radiography of such experiments – providing direct quantitative measurements on the formation of the convergent shock wave, the increased density of water on axis caused by its arrival, and its ‘bounce’ after arrival on axis. The obtained images are compared with twodimensional hydrodynamic simulations which reproduce the observed dynamics with a satisfactory agreement in density values.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2019

X-ray radiography of the overheating instability in underwater electrical explosions of wires

We introduce the measurements of the development of striation like instabilities during the electrical driven explosions of wires in a water bath. In vacuum based wire explosion experiments, such instabilities have long been known. Yet, in spite of intense research into the explosion of wires in liquids, the development of these instabilities has either not been observed or has been assumed to play a minor role in the parameters of the exploding wire due to the tamping of the wire's explosion. Using synchrotron based multiframe radiography, we have seen the development of platelike density structures along an exploding copper wire. Our measurements were compared to a 2D magnetohydrodynamics simulation, showing similar striation formation. These observed instabilities could affect the measurements of the conductivity of the wire material in the gas-plasma state—an important parameter in the warm dense matter community. The striations could also act as a seed for other instabilities later in time if the wire is in a dense flow of material or experiences a shock from an adjacent wire—as it would do in experiments with arrays of wires.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2019

3D nanoprinting via focused electron beams

Additive manufacturing of three-dimensional objects on the nanoscale is a very relevant topic but still a highly challenging task. Among the pool of nanofabrication techniques, focused electron beam induced deposition (FEBID) has recently developed from a trial-and-error laboratory method to a predictable 3D nanoprinting technology with unique advantages. This perspective article first introduces the basic principles of 3D-FEBID, followed by an overview of historical developments with a particular emphasis on the last three years. In this work, we examine different aspects of 3D nanoprinting such as the instrumental setup, fundamental growth mechanisms, simulations, computer aided design software solutions, material properties, and application studies. For each aspect, the individual challenges and limitations are reported on. Additionally, we share our outlook about possible solutions and studies currently under investigation. As a perspective, we also address the most urgent milestones of the future and speculate on applications ranging from optics to mechanics, magnetics, and electronics, all of them benefiting from the recently improved 3D FEBID synthesis technique.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2020

Room temperature multiferroicity and magnetodielectric coupling in 0–3 composite thin films

Magnetoelectric (ME) composite thin films are promising candidates for novel applications in future nanoelectronics, spintronics, memory and other multifunctional devices as they exhibit much higher ME coupling and transition temperatures (Tc) than well-known single phase multiferroics discovered to date. Among the three types of multiferroic composite nanostructures, (2-2) layered and (1-3) vertically aligned composite nanostructures exhibit comparatively smaller ME coupling due to different shortcomings which restrict their use in many applications. Here we study the morphological, piezoresponse force microscopic (PFM), ferroelectric, magnetic, and magnetodielectric properties of 0-3 (magnetic nanoparticles (0) homogeneously distributed in ferroelectric matrices (3)) multiferroic composite thin films. The Pb(Fe 0.5 Nb 0.5 )O 3 (PFN) - Ni 0.65 Zn 0.35 Fe 2 O 4 (NZFO) particulate composite films were synthesized by pulsed laser deposition (PLD). These particulate composite thin films are completely c-axis oriented with very low surface roughness. We observed magnetic and ferroelectric T c above room temperature (RT) for all composite thin films. The PFN-NZFO 0-3 composites exhibit large polarization, high saturated magnetization with low coercive field, low dielectric loss along with magnetodielectric coupling at RT. These nanocomposites might be utilized in next generation nano/microelectronics and spintronic devices.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Peculiarities of planar shockwave interaction with air–water interface and solid target

We present the results of the research on underwater electrical explosion of planar copper wire arrays, accompanied by the generation of a planar shock, using the synchrotron-based phase-contrast radiography imaging capabilities of the ID19 beamline at the European Synchrotron Radiation Facility. It is shown that the interaction of a strong shock with an air–water interface leads to additional acceleration of the wire expansion due to a rarefaction wave along with the emergence of micro-jets. In the case of a target placed above the array, we observed the formation of a cavity between the array and the target due to the interaction of two rarefaction waves. Furthermore, the results of two-dimensional hydrodynamic simulations of the wire explosion and the interaction of the generated shock with the water–air and water-target interfaces showed good agreement with experimental results.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Investigations of room temperature multiferroic and magneto-electric properties of (1-Φ) PZTFT-Φ CZFMO particulate composites

Multiferroic composites consisting of a single-phase multiferroic [0.6(PbZr 0.53 Ti 0.47 O 3 )-0.4(PbFe 0.5 Ta 0.5 )O 3 ] as a matrix and a magnetostrictive phase (Co 0.6 Zn 0.4 Fe 1.7 Mn 0.3 O 4 ) dispersed in the matrix are fabricated via hybrid synthesis technique. The structure and surface morphology studies using x-ray diffraction and field emission scanning electron microscopy techniques indicate the formation of 3-0 type particulate composites. Coexistence of soft-magnetic behavior and ferroelectric characteristics are confirmed for composites from magnetization vs magnetic field (M–H) and polarization vs electric field (P–E) measurements, respectively. Magneto-dielectric (MD) measurement shows significant changes in the dielectric properties with the application of a magnetic field, indicating the existence of strong MD behavior. The biquadratic nature of magneto-electric (ME) coupling is described by the Landau free energy equation arising from the strain transfer at the interfaces between the constituent phases. The direct magneto-electric voltage coefficient measurement also confirms very strong coupling between ferroelectricity and magnetism and supports the strain-mediated magneto-electric effect in composites. The Φ = 0.3 composite exhibits the maximum ME coefficient of 20.72 mV/cm Oe with M S = 24.62 emu/g, H C = 59.66 Oe, and piezoelectric coefficient value d 33 = 19 pC/N. In conclusion, the strong magneto-electric effect along with low dielectric loss at room temperature in these composites suggests their suitability for multifunctional magneto-electric device applications such as magnetic sensors, etc.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Synchrotron radiography of Richtmyer–Meshkov instability driven by exploding wire arrays

We present a new technique for the investigation of shock-driven hydrodynamic phenomena in gases, liquids, and solids in arbitrary geometries. The technique consists of a pulsed power-driven resistive wire array explosion in combination with multi-MHz synchrotron radiography. Compared to commonly used techniques, it offers multiple advantages: (1) the shockwave geometry can be shaped to the requirements of the experiment, (2) the pressure (P > 300 MPa) generated by the exploding wires enables the use of liquid and solid hydrodynamic targets with well-characterized initial conditions (ICs), (3) the multi-MHz radiography enables data acquisition to occur within a single experiment, eliminating uncertainties regarding repeatability of the ICs and subsequent dynamics, and (4) the radiographic measurements enable estimation of compression ratios from the x-ray attenuation. In addition, the use of a synchrotron x-ray source allows the hydrodynamic samples to be volumetrically characterized at a high spatial resolution with synchrotron-based microtomography. This experimental technique is demonstrated by performing a planar Richtmyer–Meshkov instability (RMI) experiment on an aerogel–water interface characterized by Atwood number A0∼−0.8 and Mach number M∼1.5. The qualitative and quantitative features of the experiment are discussed, including the energy deposition into the exploding wires, shockwave generation, compression of the interface, startup phase of the instability, and asymptotic growth consistent with Richtmyer's impulsive theory. Additional effects unique to liquids and solids—such as cavitation bubbles caused by rarefaction flows or initial jetting due to small perturbations—are observed. It is also demonstrated that the technique is not shape dependent by driving a cylindrically convergent RMI experiment.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Multi frame radiography of supersonic water jets interacting with a foil target

Pulsed-power-driven underwater electrical explosion of cylindrical or conical wire arrays produces supersonic water jets that emerge from a bath, propagating through the air above it. Interaction of these jets with solid targets may represent a new platform for attaining materials at high pressure (>1010 Pa) conditions in a university-scale laboratory. However, measurements of the internal structure of such jets and how they interact with targets are difficult optically due to large densities and density contrasts involved. We utilized multi-frame x-ray radiographic imaging capabilities of the ID19 beamline at the European Synchrotron Radiation Facility to explore the water jet and its interaction with a 50 μm thick copper foil placed a few mm from the surface of water. The jet was generated with a ∼130 kA-amplitude current pulse of ∼450 ns rise time applied to a conical wire array. X-ray imaging revealed a droplet-type structure of the jet with an average density of <400 kg/m3 propagating with a velocity of ∼1400 m/s. Measurements of deformation and subsequent perforation of the target by the jet suggested pressures at the jet–target interface of ∼5 × 109 Pa. The results were compared to hydrodynamic simulations for better understanding of the jet parameters and their interaction with the foil target. These results can be used in future research to optimize the platform, and extend it to larger jet velocities in the case of higher driving currents supplied to the wire array.

Physics↗
DOE OSTI2024

Studies on the compositional dependent structural and electrical properties of CaTiO3-modified K0.5Na0.5NbO3 piezoelectric system

Lead-free piezoelectric ceramics of (1 − x)K0.5Na0.5NbO3-xCaTiO3 were fabricated, and their crystal structure, microstructure, and electrical properties were systematically studied. Rietveld refinement of the x-ray diffraction data and Raman spectroscopic analyses revealed a composition-dependent structural phase transition: three phase transitions, namely, from a pure orthorhombic phase for x ≤ 0.02 to a mixed phase of orthorhombic and tetragonal phases (0.03 ≤ x ≤ 0.08) and finally another mixed phase of tetragonal + cubic for x = 0.10 and 0.15 at room temperature (RT). The morphological study reveals a decrease in grain size along with a more uniform distribution of grains as the concentration of CaTiO3 (CT) increases; notably, a homogeneous distribution of grains is observed for x = 0.05. The temperature-dependent dielectric properties show two phase transitions, from orthorhombic to tetragonal (TO-T) and tetragonal to cubic (TC), for unmodified K0.5Na0.5NbO3 (KNN). However, both the phase transition temperatures (TO-T and TC) decrease, and the transition peaks broaden with an increase in CT substitution, and for x > 0.06, the TO-T shifted below RT. The broadening of the transition peak at TO-T may be due to the relaxation behavior. Among the prepared samples, the 5 mol. % CT-modified KNN shows the optimum electrical properties (d33 = 114 pC/N, ɛr = 412, and 2Pr = 15.25 μC/cm2) at RT. The enhanced electrical properties for x = 0.05 are due to the coexistence of orthorhombic and tetragonal phases, facilitating easy polarization rotation and flattening of the free energy profile. A phase diagram has been constructed based on the information gathered from the temperature-dependent dielectric measurements, RT x-ray diffraction, and Raman spectroscopy data and is discussed in detail.

Physics↗
DOE OSTI2024

Integration of scanning probe microscope with high-performance computing: Fixed-policy and reward-driven workflows implementation

The rapid development of computation power and machine learning algorithms has paved the way for automating scientific discovery with a scanning probe microscope (SPM). The key elements toward operationalization of the automated SPM are the interface to enable SPM control from Python codes, availability of high computing power, and development of workflows for scientific discovery. Here, we build a Python interface library that enables controlling an SPM from either a local computer or a remote high-performance computer, which satisfies the high computation power need of machine learning algorithms in autonomous workflows. We further introduce a general platform to abstract the operations of SPM in scientific discovery into fixed-policy or reward-driven workflows. Furthermore, our work provides a full infrastructure to build automated SPM workflows for both routine operations and autonomous scientific discovery with machine learning.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Invariant discovery of features across multiple length scales: Applications in microscopy and autonomous materials characterization

Physical imaging is a foundational characterization method in areas from condensed matter physics and chemistry to astronomy and spans length scales from atomic to universe. Images encapsulate crucial data regarding atomic bonding, materials microstructures, and dynamic phenomena such as microstructural evolution and turbulence, among other phenomena. The challenge lies in effectively extracting and interpreting this information. Variational Autoencoders (VAEs) have emerged as powerful tools for identifying the underlying factors of variation in image data, providing a systematic approach to distilling meaningful patterns from complex data sets. However, a significant hurdle in their application is the definition and selection of appropriate descriptors reflecting local structures. Here, we introduce the scale-invariant VAE approach (SI-VAE) based on the progressive training of the VAE with the descriptors sampled at different length scales. The SI-VAE allows the discovery of the length scale-dependent factors of variation in the system. Here, we illustrate this approach using the ferroelectric domain images and generalize it to the movies of the electron-beam induced phenomena in graphene and topography evolution across combinatorial libraries. This approach can further be used to initialize the decision making in automated experiments including structure–property discovery and can be applied across a broad range of imaging methods. This approach is universal and can be applied to any spatially resolved data including both experimental imaging studies and simulations, and can be particularly useful for exploration of phenomena such as turbulence and scale-invariant transformation fronts.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Planar shock-induced bubble collapse and jetting in water captured via X-ray phase contrast imaging

Shock wave–bubble interactions in water manifest rich dynamics driven by a combination of strong pressure and density mismatches. They have a wide variety of applications, including the injection of pharmaceuticals, and through scaling, enable the exploration of various aspects of high-energy-density systems such as inertial confinement fusion. In this work, the interaction between a micrometric nitrogen bubble and a planar shock wave, characterized by a Mach number of M = 1.24 and a peak pressure of p max = 0.57 , is experimentally recorded using ultra-high-speed x-ray phase contrast imaging. Highly resolved radiographs provide access to all phase discontinuities along the beam path, offering quantities such as the time-varying bubble size, the speed of a jet produced during the bubble collapse, and the time evolution of the shock wave front, which are critical benchmark data for numerical scheme validation. This study addresses the lack of well-characterized, repeatable, and high spatiotemporal resolution experiments at negative Atwood numbers by providing shock–bubble visualization and corresponding numerical simulation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2012

Synthesis and electroplating of high resolution insulated carbon nanotube scanning probes for imaging in liquid solutions

High resolution and isolated scanning probe microscopy (SPM) is in demand for continued development of energy storage and conversion systems involving chemical reactions at the nanoscale as well as an improved understanding of biological systems. We can use carbon nanotubes (CNTs) have large aspect ratios and, if leveraged properly, to develop high resolution SPM probes. Isolation of SPM probes can be achieved by depositing a dielectric film and selectively etching at the apex of the probe. Here, the fabrication of a high resolution and isolated SPM tip is demonstrated using electron beam induced etching of a dielectric film deposited onto an SPM tip with an attached CNT at the apex.

36 MATERIALS SCIENCE↗