Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Parallel optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Experimental and Computational Analysis of a Rotating Detonation Combustor

Rotating detonation combustor (RDC) research has progressed along parallel experimental and computational paths with limited opportunities for validation. Validation is a crucial step to ensure RDC simulations provide an accurate representation of the physical phenomena, and thus, can be used with confidence for design optimization in different applications. In this study, data from a quasi-two-dimensional computational fluid dynamic simulation in an annular RDC are compared with experimental measurements including particle image velocimetry at 100 kHz. Results show good agreement between measured and simulated dynamic pressures, Chapman-Jouguet speeds, and static pressure distributions. Velocity measurements at the annulus exit show good temporal and quantitative agreement with simulations including spikes from the passing shock.

Detonation↗
NASA NTRSDate not supplied

Advanced Parametric Lobe Mixer Concepts for Internally Mixed Nozzles

A continuation of efforts to optimize a dual-stream lobe mixer for supersonic commercial flight are detailed, adding scarfing and scalloping features to a baseline lobe mixer previously optimized within a baseline parametric space. These "advanced features" are parameterized by four quantities: scarfing angle 𝜁, scallop height ℎ 𝑠 , scallop depth 𝑑 𝑠 , and scallop conic focal parameter 𝜌 𝑠 . Two baseline mixers, one parallel and one vortical, form the basis for an eighteen-case study to investigate the effects of each parameter in single-axis fashion. Aerodynamic performance is evaluated through velocity coefficient 𝐶 𝑉 . Moderate performance increases are seen with increasing scallop height and depth on the parallel mixer, and with increasing scarfing angle on the vortical mixer. Flowfield analysis is presented through visualization of axial and cross-stream vorticity development through the duct, as well as density variation. A correlation between axial vorticity and density variation decay was found, with earlier introduction of axial vorticity found to result in improved aerodynamic performance and potential noise suppression.

Lobe Mixer↗
NASA NTRS2014

Using SpF to Achieve Petascale for Legacy Pseudospectral Applications

Pseudospectral (PS) methods possess a number of characteristics (e.g., efficiency, accuracy, natural boundary conditions) that are extremely desirable for dynamo models. Unfortunately, dynamo models based upon PS methods face a number of daunting challenges, which include exposing additional parallelism, leveraging hardware accelerators, exploiting hybrid parallelism, and improving the scalability of global memory transposes. Although these issues are a concern for most models, solutions for PS methods tend to require far more pervasive changes to underlying data and control structures. Further, improvements in performance in one model are difficult to transfer to other models, resulting in significant duplication of effort across the research community. We have developed an extensible software framework for pseudospectral methods called SpF that is intended to enable extreme scalability and optimal performance. Highlevel abstractions provided by SpF unburden applications of the responsibility of managing domain decomposition and load balance while reducing the changes in code required to adapt to new computing architectures. The key design concept in SpF is that each phase of the numerical calculation is partitioned into disjoint numerical kernels that can be performed entirely inprocessor. The granularity of domain decomposition provided by SpF is only constrained by the datalocality requirements of these kernels. SpF builds on top of optimized vendor libraries for common numerical operations such as transforms, matrix solvers, etc., but can also be configured to use open source alternatives for portability. SpF includes several alternative schemes for global data redistribution and is expected to serve as an ideal testbed for further research into optimal approaches for different network architectures. In this presentation, we will describe our experience in porting legacy pseudospectral models, MoSST and DYNAMO, to use SpF as well as present preliminary performance results provided by the improved scalability.

DYNAMO↗
NASA NTRS1995

Scalability of Parallel Spatial Direct Numerical Simulations on Intel Hypercube and IBM SP1 and SP2

The implementation and performance of a parallel spatial direct numerical simulation (PSDNS) approach on the Intel iPSC/860 hypercube and IBM SP1 and SP2 parallel computers is documented. Spatially evolving disturbances associated with the laminar-to-turbulent transition in boundary-layer flows are computed with the PSDNS code. The feasibility of using the PSDNS to perform transition studies on these computers is examined. The results indicate that PSDNS approach can effectively be parallelized on a distributed-memory parallel machine by remapping the distributed data structure during the course of the calculation. Scalability information is provided to estimate computational costs to match the actual costs relative to changes in the number of grid points. By increasing the number of processors, slower than linear speedups are achieved with optimized (machine-dependent library) routines. This slower than linear speedup results because the computational cost is dominated by FFT routine, which yields less than ideal speedups. By using appropriate compile options and optimized library routines on the SP1, the serial code achieves 52-56 M ops on a single node of the SP1 (45 percent of theoretical peak performance). The actual performance of the PSDNS code on the SP1 is evaluated with a "real world" simulation that consists of 1.7 million grid points. One time step of this simulation is calculated on eight nodes of the SP1 in the same time as required by a Cray Y/MP supercomputer. For the same simulation, 32-nodes of the SP1 and SP2 are required to reach the performance of a Cray C-90. A 32 node SP1 (SP2) configuration is 2.9 (4.6) times faster than a Cray Y/MP for this simulation, while the hypercube is roughly 2 times slower than the Y/MP for this application. KEY WORDS: Spatial direct numerical simulations; incompressible viscous flows; spectral methods; finite differences; parallel computing.

Joslin, Ronald D.↗
DOE OSTI2021

Stratigraphic Identification with Airborne Electromagnetic Methods at the Hanford Site, Washington

Stratigraphic units can influence the fate and transport of subsurface contaminants within groundwater. Units having coarse-grained sediments act as preferential flow pathways, and therefore can accelerate the transport of contaminants to reach human and ecological receptors. At legacy waste sites, detailed knowledge of subsurface stratigraphy can be used for effective monitoring and remediation planning to help minimize risk to human health and the environment. Airborne electromagnetic (AEM) methods can non-invasively provide information on kilometer-scale or larger subsurface stratigraphic features and fill informational gaps in directly sampled data from sparsely located boreholes. In this paper, we present inversion results of a 412 line-km frequency-domain AEM survey to delineate subsurface stratigraphic features at the Hanford Site, located in southeastern Washington State. The inversion was performed using a massively parallel 3D electromagnetic modeling and inversion code, where the modeling is based on solving frequency-domain Maxwell’s equations using an unstructured-mesh finite-element method and the inversion employs a Gauss-Newton optimization scheme. The results are compared to an underlying geologic framework model (GFM), built by interpolating contact depths of stratigraphic units interpreted from site borehole datasets. In areas with good borehole coverage, the inversion results show a good match with the GFM to a depth of about 60 m. Outside of these areas, the inversion results exhibit inconsistencies from the assumptions made to create the GFM, demonstrating that the AEM survey results can be used to improve the understanding of the geological conceptual model.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Effects of magnetic field assisted heat treatment on the microstructure and mechanical properties of Fe-0.63 %C alloy

This study investigates the influence of an applied magnetic field on the microstructural evolution and mechanical properties of hypoeutectoid steels subjected to heat treatment. Tensile tests and microstructural analysis were performed on samples processed under varying magnetic field strengths (0 T, 5 T, and 9 T) and different austenitization incubation times. The results indicate that the application of a magnetic field alters the fraction of proeutectoid ferrite phase without changing the cooling rates and heat treatment process. Additionally, pearlite microstructural features such as lamellar spacing and misorientation angles exhibit variations under different field strengths. While the pearlite nodule diameter remains largely unaffected, an increase in percentage elongation and strength is observed in the 5 T treated sample, attributed to changes in microstructural features with the magnetic field. Additionally, the percentage elongation is reduced in the samples heat treated with reduced austenitization incubation times. The study further demonstrates that low-angle misorientations increased in the samples taken parallel to the magnetic field direction, influencing the mechanical response. These findings suggest that applying a magnetic field during heat treatment provides an additional driving force for phase transformations, offering a manufacturing process for tailoring microstructures and optimizing mechanical properties. Moreover, integrating magnetic fields in heat treatment processes has potential benefits in energy efficiency.

High magnetic field↗
DOE OSTI2024

Pilot microbial electrolysis cell closes the hydrogen loop for hydrothermal wet waste conversion to jet fuel

The global shift toward net-zero emissions necessitates resource recovery from wet waste. In this study, we demonstrate the first feasibility of combining pilot-scale microbial electrolytic cells (MECs) with hydrothermal liquefaction (HTL) for simultaneous post-hydrothermal liquefaction wastewater (PHW) treatment and efficient hydrogen (H₂) production to meet biocrude upgrading requirements. Long-term single reactor operation revealed that fixed anode potential enabled rapid startup, and low catholyte pH and high salinity were effective in suppression of cathodic methanogenesis and acetogenesis – resulting in high current density of 16.6 A m –2 and 9.3 A m –2 when feeding synthetic wastewater and PHW respectively. Additionally, the anode biofilm exhibited spatial variations in response to local environmental conditions. In conclusion, onsite parallel or serial operations of multiple MECs showed good performance using actual PHW with a record-high H 2 production rate of 0.5 L L R day –1 for MEC over 10 liters scale, and the optimal chemical oxygen demand (COD)-to-H 2 yield reached 0.127 kg-H 2 per kg-COD, supporting a self-sufficient, closed-loop upgrade to jet fuel.

08 HYDROGEN↗
DOE OSTI2023

Crystal structure of deracoxib, C 17 H 14 F 3 N 3 O 3 S

The crystal structure of deracoxib has been solved and refined using synchrotron X-ray powder diffraction data, and optimized using density functional theory techniques. Deracoxib crystallizes in space group Pbca (#61) with a = 9.68338(11), b = 9.50690(5), c = 38.2934(4) Å, V = 3525.25(3) Å 3 , and Z = 8. The molecules stack in layers parallel to the ab-plane. N–H∙∙∙O hydrogen bonds link the molecules along the b-axis, in chains with the graph set C1,1(4), as well as more-complex patterns. N–H∙∙∙N hydrogen bonds link the layers. The powder pattern has been submitted to ICDD for inclusion in the Powder Diffraction File™ (PDF®).

36 MATERIALS SCIENCE↗
DOE OSTI2021

A Non-cooperative Game-based Approach to Distributed Beam Scheduling in Millimeter-Wave Networks

We consider the distributed beam scheduling problem in mm-Wave networks where the base stations may belong to different operators and there is no centralized coordination among them. Our goal is to design distributed beam scheduling algorithms such that the network utility, which is defined as a logarithm function of the average throughput of the user equipment, can be maximized. We propose a non-cooperative game-based scheduling approach where the base stations are modeled as players that greedily maximize their own utilities. The Nash Equilibrium (NE) then provides a distributed solution to the network utility maximization problem. By employing the Lyapunov optimization, the asymptotic optimality of the proposed scheduling can be guaranteed. We prove the existence and provide sufficient conditions which guarantee the uniqueness of the NE by establishing an equivalence to the Variational Inequality (VI) problem. We also propose a parallel power adaptation algorithm which is proved to converge to the NE. Numerical results show the superiority of the proposed scheduling over several distributed baseline schemes.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2020

Distributed fiber sensing systems for 3D combustion temperature field monitoring in coal-fired boilers using optically generated acoustic waves (Final Report)

In this project, we have developed and tested three kinds of fiber optic sensing systems for real time monitoring of temperature variations within an industrial scale boiler furnace. The fiber optic sensing systems target spatial and temporal distributions of high temperature profiles in a boiler furnace in fossil power plants. The reconstructed temperature profile will provide critical input for the control mechanisms to optimize the combustion process. This temperature profile will address the essential problem for fossil power plants in achieving higher efficiency and fewer pollutant emissions. Acoustic pyrometer systems have been used to reconstruct temperature field of power plant boilers based on measuring TOF (times-of-flight) of sound waves along some straight paths in a 2D cross-section of the boiler. In this project, optically generated acoustic signals from a fiber optic sensing system have replaced the acoustic signals generated from an electrical transducer. A 3D reconstruction algorithm replaced the previous 2D model. In this project, three kinds of fiber optic sensing systems have been developed and tested. They are fiber optic sensing system I, fiber optic sensing system II (Distributed Sensing System I) and fiber optic sensing system III (Distributed Sensing System II). For fiber optic sensing system I, the fiber optic ultrasound generator acts as a signal generator. A microphone, hydrophone or other electronic devices serve as a signal receiver. In this system, there are one generator and one receiver. Distance test, water temperature test, air temperature test, air temperature reconstruction, and GE ISBF pilot test were performed by Fiber optic sensing system I. The fiber optic sensing system I successfully detected temperature in all these tests. We got 2D temperature reconstruction results by using the fiber optic sensing system I and it matched the reference data. The fiber optic sensing system I successfully survived in GE ISBF boiler environment (480 °F). For fiber optic sensing system II (Distributed Sensing System I), it is an all optical ultrasound system. The fiber optic ultrasound generator acts as a signal generator. Fiber Bragg Grating (FBG) and Fabry-Perot (FP) sensor act as a signal receiver. In this system, there is one generator and one receiver. Aluminum plate temperature test, furnace high temperature test, and GE ISBF pilot test were performed by the fiber optic sensing system II. Fiber optic sensing system II successfully detected the temperature in all these tests. The fiber optic sensing system II successfully survived at up to 700 °C furnace environment and 320 °C GE ISBF boiler environment. For fiber optic sensing system III (Distributed Sensing System II), it is also an all optical ultrasound system. The fiber optic ultrasound generator acts as a signal generator. Multiple FP fiber sensors act as signal receivers. In this system, there is one generator and three receivers. Three GE ISBF pilot tests were performed by fiber optic sensing system III. The fiber optic sensing system III survived in the cold flow tests in GE’s ISBF pilot test facility. However, we didn’t get high temperature data by using this system since the nanosecond laser issues. During the period of the project, test trials, data simulation and algorithm optimization was performed successfully. For real time temperature field construction, the sampling rate must be fast enough to capture the field variations. The technology of Code-division multiple access (CDMA) is well studied which could allow parallel multiplexing, even if signals overlap in time or frequencies. Moreover, it has been known that extending the length of signal significantly improves SNR. For acoustic signals, these multiplexing techniques have also been widely used, mainly for sonar and acoustic communications. The CDMA modulation technique has been proposed and studied to guarantee high network throughput, low channel access delay and low energy consumption. We have studied the temperature field reconstruction using Gaussian Radial Basis Functions (GRBF)-based approximation approach. Reconstruction of 3D temperature field using Neural Networks with measured TOF and known propagation paths is feasible. 2D and 3D temperature field reconstruction simulation results are achieved. The milestone status is shown in Table 1. We finished milestone 1-8 and milestone 10. For milestone 9, we did three pilot tests by using the fiber optic sensing system III (Distributed Sensing System II) at GE Power. However, due to the failure of the ns laser, we did not get the temperature results. We conducted some additional tasks that were not originally proposed: 1) We fabricated a fiber optic sensing system I and did a pilot test based on this system. 2) In the proposal, we proposed two pilot tests at GE Power. In reality, we finished at least seven pilot tests at GE Power. GE Power has made a lot of efforts for supporting the pilot tests. 3) We got a simulation results based on CDMA. In summary, most of the tasks have been accomplished. The outcome of this project removed a few barriers that hinder the achievement of the final product of the distributed sensing systems. With the successful accomplishment of this project, a prototype of the fiber optic sensing system can be fabricated to attract more interests from companies and other funding agencies.

47 OTHER INSTRUMENTATION↗
NASA NTRS1976

Maximum likelihood identifier refinements for F-8C adaptive control

Design refinement is described for baseline F-8C adaptive flight test control laws which consist of simplified quadratic-optimal model-following control structures in the pitch and lateral directional axes. The variable gains of both axes are adjusted adaptively by an explicit on-line maximum likelihood parameter identifier. The identifier, consisting of five parallel computing channels which evaluate the likelihood functions at discrete points in parameter space, operates in pitch only, using pitch rate, normal acceleration, and elevator position measurements.

Stein, G.↗
NASA NTRS1998

On the Buckling of Imperfect Anisotropic Shells with Elastic Edge Supports Under Combined Loading Part I:: Theory and Numerical Analysis - Pt. 1

A rigorous solution is presented for the case of stiffened anisotropic cylindrical shells with general imperfections under combined loading, where the edge supports are provided by symmetrical or unsymmetrical elastic rings. The circumferential dependence is eliminated by a truncated Fourier series. The resulting nonlinear 2-point boundary value problem is solved numerically via the "Parallel Shooting Method". The changing deformation patterns resulting from the different degrees of interaction between the given initial imperfections and the specified end rings are displayed. Recommendations are made as to the minimum ring stiffnesses required for optimal load carrying configurations.

Arbocz, Johann↗
NASA NTRS2016

An Optimized Multicolor Point-Implicit Solver for Unstructured Grid Applications on Graphics Processing Units

In the field of computational fluid dynamics, the Navier-Stokes equations are often solved using an unstructuredgrid approach to accommodate geometric complexity. Implicit solution methodologies for such spatial discretizations generally require frequent solution of large tightly-coupled systems of block-sparse linear equations. The multicolor point-implicit solver used in the current work typically requires a significant fraction of the overall application run time. In this work, an efficient implementation of the solver for graphics processing units is proposed. Several factors present unique challenges to achieving an efficient implementation in this environment. These include the variable amount of parallelism available in different kernel calls, indirect memory access patterns, low arithmetic intensity, and the requirement to support variable block sizes. In this work, the solver is reformulated to use standard sparse and dense Basic Linear Algebra Subprograms (BLAS) functions. However, numerical experiments show that the performance of the BLAS functions available in existing CUDA libraries is suboptimal for matrices representative of those encountered in actual simulations. Instead, optimized versions of these functions are developed. Depending on block size, the new implementations show performance gains of up to 7x over the existing CUDA library functions.

Zubair, Mohammad↗
NASA NTRS1993

Fast parallel algorithms that compute transitive closure of a fuzzy relation

The notion of a transitive closure of a fuzzy relation is very useful for clustering in pattern recognition, for fuzzy databases, etc. The original algorithm proposed by L. Zadeh (1971) requires the computation time O(n(sup 4)), where n is the number of elements in the relation. In 1974, J. C. Dunn proposed a O(n(sup 2)) algorithm. Since we must compute n(n-1)/2 different values s(a, b) (a not equal to b) that represent the fuzzy relation, and we need at least one computational step to compute each of these values, we cannot compute all of them in less than O(n(sup 2)) steps. So, Dunn's algorithm is in this sense optimal. For small n, it is ok. However, for big n (e.g., for big databases), it is still a lot, so it would be desirable to decrease the computation time (this problem was formulated by J. Bezdek). Since this decrease cannot be done on a sequential computer, the only way to do it is to use a computer with several processors working in parallel. We show that on a parallel computer, transitive closure can be computed in time O((log(sub 2)(n))2).

Kreinovich, Vladik YA.↗
DOE OSTI2022

Memory access optimization for particle operations in computational fluid dynamics-discrete element method simulations

Computational Fluid Dynamics - Discrete Element Method is used to model gas-solid systems in several applications in energy, pharmaceutical and petrochemical industries. Computational performance bottlenecks often limit the problem sizes that can be simulated at industrial scale. The data structures used to store several millions of particles in such large-scale simulations have a large memory footprint that does not fit into the processor cache hierarchies on current high-performance-computing platforms, leading to reduced computational performance. This paper specifically addresses this aspect of memory access bottlenecks in industrial scale simulations. The use of space-filling curves to improve memory access patterns is described and their impact on computational performance is quantified in both shared and distributed memory parallelization paradigms. The Morton space filling curve applied to uniform grids and k-dimensional tree partitions are used to reorder the particle data-structure thus improving spatial and temporal locality in memory. The performance impact of these techniques when applied to two benchmark problems, namely the homogeneous-cooling-system and a fluidized-bed, are presented. We report these optimization techniques lead to approximately two-fold performance improvement in particle focused operations such as neighbor-list creation and data-exchange, with ~ 1.5 times overall improvement in a fluidization simulation with 1.27 million particles.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

Scalable and accurate multi-GPU-based image reconstruction of large-scale ptychography data

Abstract While the advances in synchrotron light sources, together with the development of focusing optics and detectors, allow nanoscale ptychographic imaging of materials and biological specimens, the corresponding experiments can yield terabyte-scale volumes of data that can impose a heavy burden on the computing platform. Although graphics processing units (GPUs) provide high performance for such large-scale ptychography datasets, a single GPU is typically insufficient for analysis and reconstruction. Several works have considered leveraging multiple GPUs to accelerate the ptychographic reconstruction. However, most of these works utilize only the Message Passing Interface to handle the communications between GPUs. This approach poses inefficiency for a hardware configuration that has multiple GPUs in a single node, especially while reconstructing a single large projection, since it provides no optimizations to handle the heterogeneous GPU interconnections containing both low-speed (e.g., PCIe) and high-speed links (e.g., NVLink). In this paper, we provide an optimized intranode multi-GPU implementation that can efficiently solve large-scale ptychographic reconstruction problems. We focus on the maximum likelihood reconstruction problem using a conjugate gradient (CG) method for the solution and propose a novel hybrid parallelization model to address the performance bottlenecks in the CG solver. Accordingly, we have developed a tool, called PtyGer ( Pty chographic G PU(multipl e )-based r econstruction), implementing our hybrid parallelization model design. A comprehensive evaluation verifies that PtyGer can fully preserve the original algorithm’s accuracy while achieving outstanding intranode GPU scalability.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Enhancing high-fidelity neural network potentials through low-fidelity sampling

The efficacy of neural network potentials (NNPs) critically depends on the quality of the configurational datasets used for training. Prior research using empirical potentials has shown that well-selected liquid–solid transitional configurations of a metallic system can be translated to other metallic systems. This study demonstrates that such validated configurations can be relabeled using density functional theory (DFT) calculations, thereby enhancing the development of high-fidelity NNPs. Training strategies and sampling approaches are efficiently assessed using empirical potentials and subsequently relabeled via DFT in a highly parallelized fashion for high-fidelity NNP training. Our results reveal that relying solely on energy and force for NNP training is inadequate to prevent overfitting, highlighting the necessity of incorporating stress terms into the loss functions. To optimize training involving force and stress terms, we propose employing transfer learning to fine-tune the weights, ensuring that the potential surface is smooth for these quantities composed of energy derivatives. This approach markedly improves the accuracy of elastic constants derived from simulations in both empirical potential-based NNPs and relabeled DFT-based NNPs. Overall, this study offers significant insights into leveraging empirical potentials to expedite the development of reliable and robust NNPs at the DFT level.

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1987

Instructions to working groups

The key to the success of this workshop is your active participation in the working group process. The goals of this workshop are to address four major questions regarding Cockpit Resource Management (CRM) Training. To some extent the working group topic areas parallel these issues, but in some cases they do not. However, it is important for all of the working groups to keep these general questions in mind during their deliberations: (1) What are the essential elements of an optimal CRM Training program; (2) What are the strengths and weaknesses of current approaches to CRM Training; (3) How can CRM Training best be implemented, and what barriers exist; and (4) Is CRM Training effective, do we know, and if not, how can we find out.

Foushee, H. Clayton↗