Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PORE PRESSURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

Numerical evaluation of effective unsaturated hydraulic properties for fractured rocks

To represent a heterogeneous unsaturated fractured rock by its homogeneous equivalent, Monte Carlo simulations are used to obtain upscaled (effective) flow properties. In this study, we present a numerical procedure for upscaling the van Genuchten parameters of unsaturated fractured rocks by conducting Monte Carlo simulations of the unsaturated flow in a domain under gravity-dominated regime. The simulation domain can be chosen as the scale of block size in the field-scale modeling. The effective conductivity is computed from the steady-state flux at the lower boundary and plotted as a function of the averaging pressure head or saturation over the domain. The scatter plot is then fitted using van Genuchten model and three parameters, i.e., the saturated conductivity K{sub s}, the air-entry parameter {alpha}, the pore-size distribution parameter n, corresponding to this model are considered as the effective K{sub s}, effective {alpha}, and effective n, respectively.

58 GEOSCIENCES↗

High temperature oxidation behaviors of bulk SiC with low partial pressures of air and water vapor in argon

Oxidation behaviors of bulk SiC at 1000–1400 °C in Ar-20 vol% H 2 O-10 vol% air were investigated. The thickness of the passivation oxide layer showed a parabolic increase with time. Dense and uniform layers formed below 1200 °C, whereas pores and cracks were observed at higher temperatures. An analytical model was proposed to estimate the oxide layer growth and SiC mass loss rate. The SiC layer should be effective in retaining the fission products after oxidation by excessive water and air. This work is the first detailed study of SiC layer oxidation during loss of coolant accidents (LOCA) for HTGRs.

36 MATERIALS SCIENCE↗

Formation dry-out from CO2 injection into saline acquifers: Part 2, Analytical model for salt precipitation

From a mass balance for water dissolved into the flowing CO{sub 2} stream, and a consideration of saturation profiles from the Buckley-Leverett (1942) fractional flow theory, we derive an equation that directly relates gas saturation S{sub g,d} at the dry-out front to temperature, pressure and salinity dependence of fluid properties. The equation is easily solved by iteration or interpolation. From gas saturation at the front we derive the average gas saturation in the dry-out region, from which we obtain the 'solid saturation' S{sub S}, i.e., the fraction of pore space filled with solid precipitate. Values of S{sub S} derived from this theory show excellent agreement with numerical simulations presented in the preceding companion paper ('Part 1'). Thus, from relative permeabilities and fluid properties at in situ conditions prior to CO{sub 2} injection, it is possible to directly make an accurate estimate of solids precipitation, without having to perform a numerical simulation of the injection process.

54 ENVIRONMENTAL SCIENCES↗

Effects of Pouring Temperature and Electromagnetic Stirring on Porosity and Mechanical Properties of A357 Aluminum Alloy Rheo-Diecasting

Semisolid slurry of A357 aluminum alloy was prepared using a temperature-controllable electromagnetic stirrer and rheo-diecast at different temperatures. The effects of pouring temperature and electromagnetic stirring (EMS) on the porosity in rheo-diecast samples, as well as the relation between porosity and mechanical properties, were investigated. The results show that pouring temperature and EMS had minor influences on rheo-diecast microstructure but marked influence on the porosity. With decreasing slurry pouring temperature, the porosity decreased first and then increased, whereas the maximum pore ratio (ratio of shape factor to diameter of the largest pore) increased first and then decreased. The maximum pore ratio determines the level of tensile strength and elongation, and higher mechanical properties can be obtained with smaller and rounder pores in samples. The mechanical properties of the rheo-diecast samples increased linearly with increasing maximum pore ratio. The maximum pore ratio was 1.43 µm{sup −1}, and the minimum porosity level was 0.37% under EMS condition for the rheo-diecast samples obtained at a pouring temperature of 608 °C. With this porosity condition, the maximum tensile strength and elongation were achieved at 274 MPa and 4.9%, respectively. It was also revealed that EMS improves mechanical properties by reduction in porosity and an increase in maximum pore ratio.

36 MATERIALS SCIENCE↗

Assessing the potential of composite confining systems for secure and long-term CO 2 retention in geosequestration

A potential geologic target for CO 2 storage should ensure secure containment of injected CO 2 . Traditionally, this objective has been achieved by targeting reservoirs with overlying seals-regionally extensive, low permeability units that have been proven capable of retaining buoyant fluid accumulations over geologic time. However, considering that the amount of CO 2 is limited by a decadal injection period, vertical migration of CO 2 can be effectively halted by a composite system of discontinuous shale/silt/mudstone barriers in bedded sedimentary rocks. Here, we studied the impact of depositional architectures in a composite confining system on CO 2 migration and confinement at reservoir scale. We stochastically generated lithologically heterogeneous reservoir models containing discontinuous barriers consistent with statistical distributions of net-sand-to-gross-shale ratio (NTG) and horizontal correlation lengths derived from well log data and observations of producing hydrocarbon fields in Southern Louisiana. We then performed an extensive suite of reservoir simulations of CO 2 injection and post-injection to evaluate the sensitivity of CO 2 plume migration and pressure response of the composite system to a series of geologic and fluid parameters including the lateral continuity of barriers, NTG, permeability anisotropy within the sand body, and capillary pressure contrast between the sand and shale facies. The results indicate that lateral continuity of barriers and NTG are the dominant controls on CO 2 plume geometry and pressure build-up in the reservoir, while the impact of NTG is particularly pronounced. The significance of intraformational barriers becomes apparent as they facilitate the local capillary trapping of CO 2 . Those barriers improve the pore space occupancy by promoting a more dispersed shape of the plume and ultimately retard the buoyancy-driven upward migration of the plume post injection.

58 GEOSCIENCES↗

Fundamental Study of Disposition and Release of Methane in a Shale Gas Reservoir

The recent boom in shale gas production through hydrofracturing has reshaped the energy production landscape in the United States. Wellbore production rates vary greatly among the wells within a single field and decline rapidly with time, thus bring up a serious concern with the sustainability of shale gas production. Shale gas production starts with creating a fracture network by injecting a pressurized fluid in a wellbore. The induced fractures are then held open by proppant particles. During production, gas releases from the mudstone matrix, migrates to nearby fractures, and ultimately reaches a production wellbore. Given the relatively high permeability of the induced fractures, gas release and migration in low-permeability shale matrix is likely to be a limiting step for long-term wellbore production. Therefore, a clear understanding of the underlying mechanisms of methane disposition and release in shale matrix is crucial for the development of new technologies to maximize gas production and recovery. Shale is a natural nanocomposite material with distinct characteristics of nanometer-scale pore sizes, extremely low permeability, high clay contents, significant amounts of organic carbon, and large spatial heterogeneities. Our work has shown that nanopore confinement plays an important role in methane disposition and release in shale matrix. Using molecular simulations, we show that methane release in nanoporous kerogen matrix is characterized by fast release of pressurized free gas (accounting for ~ 30 - 47% recovery) followed by slow release of adsorbed gas as the gas pressure decreases. The first stage is driven by the gas pressure gradient while the second stage is controlled by gas desorption and diffusion. The long-term production decline appears controlled by the second stage of gas release. We further show that diffusion of all methane in nanoporous kerogen behaves differently from the bulk phase, with much smaller diffusion coefficients. The MD simulations also indicate that a significant fraction (3 - 35%) of methane deposited in kerogen can potentially become trapped in isolated nanopores and thus not recoverable. We have successfully established experimental capabilities for measuring gas sorption and desorption on shale and model materials under a wide range of physical and chemical conditions. Both low and high pressure measurements show significant sorption of CH 4 and CO 2 onto clays, implying that methane adsorbed on clay minerals could contribute a significant portion of gas-in-place in an unconventional reservoir. We have also studied the potential impact of the interaction of shale with hydrofracking fluid on gas sorption. We have found that the CH 4 -CO 2 sorption capacity for the reacted sample is systematically lower (by a factor of ~2) than that for the unreacted (raw) sample. This difference in sorption capacity may result from a mineralogical or surface chemistry change of the shale sample induced by fluid-rock interaction. Our results shed a new light on mechanistic understanding gas release and production decline in unconventional reservoirs.

04 OIL SHALES AND TAR SANDS↗

Modeling of Leaching Filter Pressure Drop and Fouling Behavior

A new simulation capability has been developed for modeling the flow and thermal performance of chemical processes that involve multiphase, chemically-complex flows. This capability is applied to the ultrafiltration process which will be used in conjunction with caustic and/or oxidative leaching to concentrate high level waste in the Waste Treatment and Immobilization Plant (WTP) at the US DOE Hanford site. The separation of supernatant from undissolved solids is an important aspect of these processes. The design and likely operational performance of the proposed ultrafiltration system for the WTP facility have been called into question by external reviewers. Lattice methods are used to model both the pore scale filtration mechanisms in the filter material and the filter device scale performance. Simulation results are compared with data from experiments.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Constraining the Texture and Composition of Pore-Filling Cements at Gale Crater, Mars

The Mars Science Laboratory (MSL) rover Curiosity has encountered a wide variety of sedimentary rocks deposited in fluvio-lacuestrine sequences at the base of Gale Crater. The presence of sedimentary rocks requires that initial sediments underwent diagenesis and were lithified. Lithification involves sediment compaction, cementation, and re-crystallization (or authigenic) processes. Analysis of the texture and composition of the cement can reveal the environmental conditions when the cements were deposited, enabling better understanding of early environments present within Gale Crater. The first step in lithification is sediment compaction. The Gale crater sediments do not show evidence for extensive compaction prior to cementation; the Sheepbed mudstone in Yellowknife Bay (YKB) has preserved void spaces ("hollow nodules"), indicating that sediments were cemented around the hollow prior to compaction, and conglomerates show imbrication, indicating minimal grain reorganization prior to lithification. Furthermore, assuming the maximum burial depth of these sediments is equivalent to the depth of Gale Crater, the sediments were never under more than 1 kb of pressure, and assuming a 15 C/km thermal gradient in the late Noachian, the maximum temperature of diagenesis would have been approximately 75 C. This is comparable to shallow burial diagenetic conditions on Earth. The cementation and recrystallization components of lithification are closely intertwined. Cementation describes the precipitation of minerals between grains from pore fluids, and recrystallization (or authigenesis) is when the original sedimentary mineral grains are altered into secondary minerals. The presence of authigenic smectites and magnetite in the YKB formation suggests that some recrystallization has taken place. The relatively high percentage of XRD-amorphous material (25-40%) detected by CheMin suggests that this recrystallization may be limited in scope, and therefore may not contribute significantly to the cementing material. However, relatively persistent amorphous components could exist in the Martian environment (e.g. amorphous MgSO4), so recrystallization, including loss of crystallinity, cannot yet be excluded as a method of cementation. In order to describe the rock cementation, both the rock textures and their composition must be considered. Here, we attempt to summarize the current understanding of the textural and compositional aspects of the cement across the rocks analyzed by Curiosity to this point.

Siebach, K. L.↗

Mimicking Natural Systems: Methane Hydrate Formation-Decomposition in Depleted Sediments

We have initiated a systematic study of sediment-hydrate interaction under subsurface-mimic conditions to initially focus on marine hydrates. A major obstacle to studying natural hydrate systems has been the absence of a sophisticated mimic apparatus in which the hydrate formation phenomenon can be reproduced with precision. We have designed and constructed a bench-top unit, namely flexible integrated study of hydrates (FISH), for this purpose. The unit is fully instrumented to precisely record temperatures, pressures and changes in gas volume during absorption/evolution. The Labview software allows rapid and continuous data collection during the hydrate formation/dissociation cycle. In our integrated approach, several host sediments collected from Blake Ridge, a well-researched hydrate site, were characterized using the computed microtomography technique at Beamline X-26A of the National Synchrotron Light Source at Brookhaven National Laboratory. The characterized depleted sediments were then used to study the hydrate formation/decomposition kinetics under various pressures in the FISH unit. We report two hydrate formation methods: one under continuous methane gas-flow conditions (dynamic mode) and the other in which hydrates are formed from the dissolved gas phase by diffusion (static mode). Also reported is a depressurization method, namely the step-down pressure method, to yield gas evolution data. Data from such runs with host sediment from the deepest site (667 metres) is presented. During hydrate formation, the data reveals a temperature signature that is consistent with an exothermic hydrate formation event. In the decomposition cycle, data at various pressures was analysed to yield curves with similar slopes, suggesting a zero-order dependence. The capabilities of the FISH unit and the implications of these runs in establishing a database of sediment-hydrate kinetics and pore saturation are discussed.

03 NATURAL GAS↗

Fast Pyrolysis Oil Stabilization: An Integrated Catalytic and Membrane Approach for Improved Bio-oils. Final Report

This University of Massachusetts, Amherst project, "Fast Pyrolysis Oil Stabilization: An Integrated Catalytic and Membrane Approach for Improved Bio-oils" started on 1st February 2009 and finished on August 31st 2011. The project consisted following tasks: Task 1.0: Char Removal by Membrane Separation Technology The presence of char particles in the bio-oil causes problems in storage and end-use. Currently there is no well-established technology to remove char particles less than 10 micron in size. This study focused on the application of a liquid-phase microfiltration process to remove char particles from bio-oil down to slightly sub-micron levels. Tubular ceramic membranes of nominal pore sizes 0.5 and 0.8m were employed to carry out the microfiltration, which was conducted in the cross-flow mode at temperatures ranging from 38 to 45 C and at three different trans-membrane pressures varying from 1 to 3 bars. The results demonstrated the removal of the major quantity of char particles with a significant reduction in overall ash content of the bio-oil. The results clearly showed that the cake formation mechanism of fouling is predominant in this process. Task 2.0 Acid Removal by Membrane Separation Technology The feasibility of removing small organic acids from the aqueous fraction of fast pyrolysis bio-oils using nanofiltration (NF) and reverse osmosis (RO) membranes was studied. Experiments were carried out with a single solute solutions of acetic acid and glucose, binary solute solutions containing both acetic acid and glucose, and a model aqueous fraction of bio-oil (AFBO). Retention factors above 90% for glucose and below 0% for acetic acid were observed at feed pressures near 40 bar for single and binary solutions, so that their separation in the model AFBO was expected to be feasible. However, all of the membranes were irreversibly damaged when experiments were conducted with the model AFBO due to the presence of guaiacol in the feed solution. Experiments with model AFBO excluding guaiacol were also conducted. NF membranes showed retention factors of glucose greater than 80% and of acetic acid less than 15% when operated at transmembrane pressures near 60 bar. Task 3.0 Acid Removal by Catalytic Processing It was found that the TAN reduction in bio-oil was very difficult using low temperature hydrogenation in flow and batch reactors. Acetic acid is very resilient to hydrogenation and we could only achieve about 16% conversion for acetic acid. Although it was observed that acetic acid was not responsible for instability of aqueous fraction of bio-oil during ageing studies (described in task 5). The bimetallic catalyst PtRe/ceria-zirconia was found to be best catalyst because its ability to convert the acid functionality with low conversion to gas phase carbon. Hydrogenation of the whole bio-oil was carried out at 125°C, 1450 psi over Ru/C catalyst in a flow reactor. Again, negligible acetic acid conversion was obtained in low temperature hydrogenation. Hydrogenation experiments with whole bio-oil were difficult to perform because of difficulty to pumping the high viscosity oil and reactor clogging. Task 4.0 Acid Removal using Ion Exchange Resins DOWEX M43 resin was used to carry out the neutralization of bio-oil using a packed bed column. The pH of the bio-oil increased from 2.43 to 3.7. The GC analysis of the samples showed that acetic acid was removed from the bio-oil during the neutralization and recovered in the methanol washing. But it was concluded that process would not be economical at large scale as it is extremely difficult to regenerate the resin once the bio-oil is passed over it. Task 5.0 Characterization of Upgraded Bio-oils We investigated the viscosity, microstructure, and chemical composition of bio-oils prepared by a fast pyrolysis approach, upon aging these fuels at 90ºC for periods of several days. Our results suggest that the viscosity increase is not correlated with the acids or char present in the bio-oils. The viscosity increase is due to formation of high molecular weight polymeric species over time. Our work also suggests that hydrogenation of the samples is beneficial in eliminating the viscosity increase. Task 6.0 Commercialization Assessment Renewable Oil International LLC (ROI) was responsible for Task 6.0, Commercialization Assessment. As part of this effort ROI focused on methods to reduce char carryover in the vapor stream from the fast pyrolysis reactor and residence time of the vapor in the reactor. Changes were made in the bio-oil recovery methodology and a reactor sweep gas used to reduce vapor residence time. Cyclones were placed in the vapor stream to reduce char particulate carryover. Microfiltration of the bio-oil was also researched to remove char particulate from the bio-oil. The capital cost for these improvements would be less than 2% of the total plant capital cost.

09 BIOMASS FUELS↗

Multi-system analysis of offshore geologic carbon storage: a review of open-source data science solutions

Geologic carbon storage projects are maturing worldwide and the footprint of deployment in the offshore is expanding. At present, there are ten projects in operation or that have been completed, more than 50 in construction and development, and dozens of characterization studies completed or underway. Offshore geologic carbon storage offers potential benefits over onshore geologic carbon storage. These offshore projects are generally remote in location, distant from population centers, and avoid complicated pore space rights while having abundant prospective storage potential. Some offshore fields targeted for carbon storage have comparatively fewer prior borehole penetrations except for areas that have been explored for petroleum production, minimizing potential issues such as pressure interference and infrastructure impacts. Yet offshore geologic carbon storage projects face distinctive technical and economic challenges, such as seafloor geohazards (e.g., seabed instability), expensive maritime transport, and meteorological-oceanographic conditions that can damage infrastructure and impact operations. Analytical capabilities and improved computational speeds have advanced engineering, earth and energy sciences in the wake of the arrival of modern data science over the last decade. These advancements have created an opportunity for integrated, multi-systems modeling approaches utilizing artificial intelligence and machine learning that are no longer limited by computational issues. Analytical tools developed alongside this advancement in data science can be leveraged to calibrate the potential advantages and challenges of carbon storage operations in the offshore. New methods and approaches that incorporate data science to analyze multiple aspects of engineered and natural systems can provide insights that complement the characterization and onsite engineering that traditional commercial and operational software addresses. These new methods and approaches can potentially improve the outcome of energy operations and carbon storage. Providing multi-system, science-driven data analytics enhances the knowledge base that offshore developers, operators, and regulatory bodies may draw from to improve offshore site selection and operational efficiency. Here, we provide a brief synopsis of geologic carbon storage efforts to date, an overview of the engineered and natural systems involved in offshore geologic carbon storage, and a review of publicly available, open-source, offshore and/or carbon storage related data- and science-driven tools developed by 2010 or later that are suitable for screening and assessing regions for offshore geologic carbon storage.

artificial intelligence↗

Chromia refractory brick with carbon treatment

The disclosure provides a refractory brick system comprising a chromia refractory brick for operation in the slagging environment of an air-cooled gasifier. The chromia refractory brick comprises a ceramically-bonded porous chromia refractory having a porosity greater than 9% and having carbon deposits residing within the pores. The brick may be further comprised of Al.sub.2O.sub.3. The air-cooled gasifier generates a liquefied slag in contact with the refractory brick and generally operates at temperatures between 1250.degree. C. and 1575.degree. C. and pressures between 300 psi to 1000 psi, with oxygen partial pressures generally between 10.sup.-4 and 10.sup.-10 atm. The refractory brick performs without substantial chromium carbide or chromium metal formation in the low oxygen partial pressure environment. The inclusion of carbon without chromium carbide formation provides for significant mitigation of slag penetration and significantly reduced refractory wear.

36 MATERIALS SCIENCE↗

Campaign 2 Level 2 Milestone Review 2009: Milestone # 3131 Grain Scale Simulation of Pore Collapse

The milestone reviewed on Sept. 16, 2009 was 'High-fidelity simulation of shock initiation of high explosives at the grain scale using coupled hydrodynamics, thermal transport and chemistry'. It is the opinion of the committee that the team has satisfied the milestone. A detailed description of how the goals were met is provided. The milestone leveraged capabilities from ASC Physics and Engineering Materials program combined with experimental input from Campaign 2. A combined experimental-multiscale simulation approach was used to create and validate the various TATB model components. At the lowest length scale, quantum chemical calculations were used to determine equations of state, thermal transport properties and reaction rates for TATB as it is decomposing. High-pressure experiments conducted in diamond anvil cells, gas guns and the Z machine were used to validate the EOS, thermal conductivity, specific heat and predictions of water formation. The predicted reaction networks and chemical kinetic equations were implemented in Cheetah and validated against the lower length scale data. Cheetah was then used within the ASC code ALE3D for high-resolution, thermo-mechanically coupled simulations of pore collapse at the micron size scale to predict conditions for detonation initiation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Design considerations for a micro-g superfluid helium fluid acquisition system

The general description, the operation, and the design of a superfluid helium (SFHe) fluid acquisition system (FAS) for use under microgravity conditions is presented. For the type of FAS considered here, where fine-mesh woven screens are used to retain flowing SFHe within a gallery arm (flow) channel, those forces which determine the flow dynamics are the micro-g accelerations, liquid surface tension, and tensile strength and cumulative pressure drops along a flow path that begins at the bulk liquid and ends at the entrance to a pump. For this case, the dimensionless number, N(T) is written as the ratio between the pressure drop across the screen and the surface tension forces at the screen for low fluid velocities. Static Bond number measurements have bene taken for SFHe using 325 x 2300 twilled Dutch screen and have indicated a screen pore hydraulic radius of 0.00031 cm.

Lee, J. M.↗

Electrohydraulic shock wave generation as a means to increase intrinsic permeability of mortar

This article discusses the influence of compressive shock waves on the permeability of cementitious materials. Shock waves are generated in water by Pulsed Arc Electrohydraulic Discharges (PAED). The practical aim is to increase the intrinsic permeability of the specimens. The maximum pressure amplitude of the shock wave is 250 MPa. It generates damage in the specimens and the evolution of damage is correlated with the intrinsic permeability of the mortar. A threshold of pressure is observed. From this threshold, the increase of permeability is linear in a semi-log plot. The influence of repeated shocks on permeability is also discussed. Qualitative X Ray Tomography illustrates the evolution of the microstructure of the material leading to the increase of permeability. Comparative results from mercury intrusion porosimetry (MIP) show that the micro-structural damage process starts at the sub-micrometric level and that the characteristic size of pores of growing volume increases.

36 MATERIALS SCIENCE↗

Investigation of representing hysteresis in macroscopic models of two-phase flow in porous media using intermediate scale experimental data

Incorporating hysteresis into models is important to accurately capture the two phase flow behavior when porous media systems undergo cycles of drainage and imbibition such as in the cases of injection and post-injection redistribution of CO 2 during geological CO 2 storage (GCS). In the traditional model of two-phase flow, existing constitutive models that parameterize the hysteresis associated with these processes are generally based on the empirical relationships. This manuscript presents development and testing of mathematical hysteretic capillary pressure—saturation—relative permeability models with the objective of more accurately representing the redistribution of the fluids after injection. The constitutive models are developed by relating macroscopic variables to basic physics of two-phase capillary displacements at pore-scale and void space distribution properties. The modeling approach with the developed constitutive models with and without hysteresis as input is tested against some intermediate-scale flow cell experiments to test the ability of the models to represent movement and capillary trapping of immiscible fluids under macroscopically homogeneous and heterogeneous conditions. The hysteretic two-phase flow model predicted the overall plume migration and distribution during and post injection reasonably well and represented the postinjection behavior of the plume more accurately than the nonhysteretic models. In conclusion, based on the results in this study, neglecting hysteresis in the constitutive models of the traditional two-phase flow theory can seriously overpredict or underpredict the injected fluid distribution during post-injection under both homogeneous and heterogeneous conditions, depending on the selected value of the residual saturation in the nonhysteretic models.

58 GEOSCIENCES↗

Highly Effective Pt-Based Water-Gas Shift Catalysts by Surface Modification with Alkali Hydroxide Salts

Here, we describe an economical and convenient method to improve the performance of Pt/alumina catalysts for the water–gas shift reaction through surface modification of the catalysts with alkali hydroxides according to the solid catalyst with ionic liquid layer approach. The results are in agreement with our findings reported earlier for methanol steam reforming. This report indicates that alkali doping of the catalyst plays an important role in the observed catalyst activation. In addition, the basic and hygroscopic nature of the salt coating contributes to a significant improvement in the performance of the catalyst. During the reaction, a partly liquid film of alkali hydroxide forms on the alumina surface, which increases the availability of H 2 O at the catalytically active sites. Kinetic studies reveal a negligible effect of the KOH coating on the rate dependence of CO and H 2 O partial pressures. In conclusion, TEM studies indicate an agglomeration of the active Pt clusters during catalyst preparation; restructuring of Pt nanoparticles occurs under reaction conditions, which leads to a highly active and stable system over 240h time on stream. Excessive pore fillings with KOH introduce a mass transfer barrier as indicated in a volcano-shaped curve of activity versus salt loading. The optimum KOH loading was found to be 7.5wt%.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗