Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PIN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

Wear Measurement of Highly Cross-linked UHMWPE using a 7 Be Tracer Implantation Technique

The very low wear rates achieved with the current highly cross-linked ultrahigh molecular weight polyethylenes (UHMWPE) used in joint prostheses have proven to be difficult to measure accurately by gravimetry. Tracer methods are there- fore being explored. The purpose of this study was to perform a proof-of-concept experiment on the use of the radioactive tracer beryllium-7 (7Be) for the determination of in vitro wear in a highly cross-linked orthopedic UHMWPE. Three cross-linked and four conventional UHMWPE pins made from compression- molded GUR 1050, were activated with 109 to 1010 7Be nuclei using a new implantation setup that produced a homogenous distribution of implanted nuclei up to 8.5 lm below the surface. The pins were tested for wear in a six-station pin-on-flat appara- tus for up to 7.1 million cycles (178 km). A Germanium gamma detector was employed to determine activity loss of the UHMWPE pins at preset intervals during the wear test. The wear of the cross-linked UHMWPE pins was readily detected and esti- mated to be 17 6 3 lg per million cycles. The conventional-to- cross-linked ratio of the wear rates was 13.1 6 0.8, in the expected range for these materials. Oxidative degradation dam- age from implantation was negligible; however, a weak depend- ence of wear on implantation dose was observed limiting the number of radioactive tracer atoms that can be introduced. Future applications of this tracer technology may include the analysis of location-specific wear, such as loss of material in the post or backside of a tibial insert.

cross-linked↗

PRELIMINARY COUPLING OF THE MONTE CARLO CODE OPENMC AND THE MULTIPHYSICS OBJECT-ORIENTED SIMULATION ENVIRONMENT (MOOSE) FOR ANALYZING DOPPLER FEEDBACK IN MONTE CARLO SIMULATIONS

In recent years the use of Monte Carlo methods for modeling reactors has become feasible due to the increasing availability of massively parallel computer systems. One of the primary challenges yet to be fully resolved, however, is the efficient and accurate inclusion of multiphysics feedback in Monte Carlo simulations. The research in this paper presents a preliminary coupling of the open source Monte Carlo code OpenMC with the open source Multiphysics Object-Oriented Simulation Environment (MOOSE). The coupling of OpenMC and MOOSE will be used to investigate efficient and accurate numerical methods needed to include multiphysics feedback in Monte Carlo codes. An investigation into the sensitivity of Doppler feedback to fuel temperature approximations using a two dimensional 17x17 PWR fuel assembly is presented in this paper. The results show a functioning multiphysics coupling between OpenMC and MOOSE. The coupling utilizes Functional Expansion Tallies to accurately and efficiently transfer pin power distributions tallied in OpenMC to unstructured finite element meshes used in MOOSE. The two dimensional PWR fuel assembly case also demonstrates that for a simplified model the pin-by-pin doppler feedback can be adequately replicated by scaling a representative pin based on pin relative powers.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Device for high spatial resolution chemical analysis of a sample and method of high spatial resolution chemical analysis

A system and method for analyzing a chemical composition of a specimen are described. The system can include at least one pin; a sampling device configured to contact a liquid with a specimen on the at least one pin to form a testing solution; and a stepper mechanism configured to move the at least one pin and the sampling device relative to one another. The system can also include an analytical instrument for determining a chemical composition of the specimen from the testing solution. In particular, the systems and methods described herein enable chemical analysis of specimens, such as tissue, to be evaluated in a manner that the spatial-resolution is limited by the size of the pins used to obtain tissue samples, not the size of the sampling device used to solubilize the samples coupled to the pins.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

System and method for configuring a channel

An integrated circuit device comprises pin resources, a memory controller circuit, a network interface controller circuit, and transmitter circuitry. The pin resources comprise pads coupled to off-chip pins of the integrated circuit device. The memory controller circuit comprises a first interface and the network interface controller circuit comprises a second interface. The transmitter circuitry is configurable to selectively couple either a first signal of the first interface or a second signal of the second interface to a first pad of the pin resources based on a pin distribution between the first interface and the second interface.

Keckler, Stephen William↗

DEVELOPMENT OF A NUCLEAR FUEL SAFEGUARDS VERIFICATION TECHNOLOGY FOR NEW FACILITY TYPES: Use of fast neutron emission tomography for spent fuel verification

With the buildup of spent fuel inventories around the world from decommissioning activities, a tool for the efficient and effective verification of a variety of fuel types for long-term disposition is needed. Fast neutron emission tomography is a promising imaging technology that can address this problem and has been under development at Oak Ridge National Laboratory for the past two years. The goal of this capability is to detect the removal or substitution of individual fuel pins in spent nuclear fuel assemblies for international safeguards applications. The present imaging technique is based on neutron emissions originating primarily from curium-244, which is produced predominantly at the end of the exposure cycle. As a result, this technique may be sensitive not only to fuel pins that are removed or substituted subsequent to all irradiation, but also to fuel pins that are substituted and subsequently irradiated. At present, a laboratory prototype imager is under construction. The purpose of the prototype is to demonstrate an imaging capabilitysufficient to resolve individual fuel pins using commercially available boron straw detectors that can withstand the high gamma ray dose from a typical spent fuel assembly. To achieve both practical measurement durations and sufficient resolution to discern individual pins, the prototype imager employs a novel collimator design where the slits of a parallel-slit collimator are rearranged to distribute them around a ring surrounding the target fuel assembly. This paper will report on simulations and experimental results undertaken to converge on a final design, image reconstruction of sample fuel types of interest, and challenges associated.

Iyengar, Anagha↗

Modeling Passive Fast-Neutron Emission Tomography of Spent Nuclear Fuel

For the past year Oak Ridge National Laboratory has been developing a passive fast-neutron emission tomography capability. Like the passive gamma emission tomography capability presently being evaluated by the International Atomic Energy Agency, the goal of this capability is to detect the removal or substitution of individual fuel pins in spent nuclear fuel assemblies for international safeguards applications, such as verifying the integrity of an assembly before transfer to difficult-to-access storage. The present imaging technique is based on neutron emissions originating primarily from curium-244, which is produced predominantly at the end of the exposure cycle. As a result, this technique may be sensitive not only to fuel pins that are removed or substituted subsequent to all irradiation, but also to fuel pins that are substituted and subsequently irradiated. At present, a laboratory prototype imager is under construction. The purpose of the prototype is to demonstrate an imaging capability sufficient to resolve individual fuel pins using commercially available boron straw detectors that can withstand the high gamma ray dose from a typical spent fuel assembly. To achieve both practical measurement durations and sufficient resolution to discern individual pins, the prototype imager employs a novel collimator design where the slits of a parallel-slit collimator are rearranged to distribute them around a ring surrounding the target fuel assembly. This presentation will report on simulations to understand the neutron signal-to-noise ratio and gamma dose rate as a function of the collimator design, the neutron detector’s response to gamma rays as a function of dose rate, and image reconstruction challenges associated with this collimator design.

Hausladen, Paul↗

Self-aligning swaging punch and method for swaging

A self-aligning swaging punch is provided for adjoining together a pin and a workpiece having a pinhole. The swaging punch comprises a shaft and a tip having an open-ended cavity. The shaft transfers an axial force from a press or hammer to the tip. The tip transfers the axial force from the shaft to a top surface of the workpiece near the pinhole. The tip may be spherical in shape for evenly deforming the workpiece near the upper edge of the pinhole. The open-ended cavity receives the pin therein and allows the pin to extend at least partially into the open-ended cavity while the tip contacts the workpiece. The open-ended cavity also ensures that the swaging punch is aligned with the pinhole and perpendicular to the surface of the workpiece when the pin is inserted into the pinhole such that the workpiece evenly deforms and presses against the pin.

42 ENGINEERING↗

Measuring, Cutting and Sorting Irradiated Control Rods to Limit the Volume of Intermediate Level Long-lived Waste - 17001

During operation, the PWR control rods are either completely extracted (scram or safety rods) or partially inserted in the operating zone of the core (fine control or operating rods). At the nominal rating conditions or close to them, the operating zone is limited to some steps of insertion in the order of a few tens of cm. In fact, only the lower part of the control rods are subjected to a significant neutron flux with an impact on the neutron activation and so on the waste classification (Low Level Short-lived Waste versus Intermediate Level Long-lived Waste). Our calculative as well as experimental experience confirms the significant presence of radionuclides in the control rods, but only in the lower parts. Measuring, cutting and finally sorting control rod scraps can reduce the volume of Intermediate Level Long-lived Waste planned for our storage deposit facility. This paper presents the EDF/DP2D methodologies followed to determine the sort criteria between the Low Level Short-lived Waste versus the Intermediate Level Long-lived Waste zones for the Silver-Indium-Cadmium control rods. The irradiated control rods are stored in cases without their head. Each case can contain several control rods, and the cases are stored under water in the fuel assembly pool. To calculate the radioactive inventories, we have developed a calculation scheme which is composed of a 3-dimensional mapping of the neutron flux, a calculation of the evolution of the isotopic compositions under neutron flux and finally a comparison between calculated and measured values. The main hypotheses of the control rods calculation take into account: - 3-dimensional geometry and 3-dimensional neutron sources distribution, - the isotopic compositions including impurities, - the history of irradiation resulting mainly from the daily power production, the positions of the control rods in the loading patterns and the positions in the axial operating zone. In order to validate the calculations, measurements were made 20 meters under water in the fuel assembly pool. The experimental results show the presence of many gamma emitter radionuclides. Only Ag-108m was retained for validating the calculations. This is due to the fact that silver is considered as the 'standard' chemical element for our control rods and silver produces Ag-108m which is a long-lived gamma emitter radionuclide. The analysis of the calculated results and the measured values allow us to build a simplified physics model for the simulation of the control rods activation. Finally three sort criteria can be proposed: - Without measurement devices, the sorting is based on an empirical sort criterion. Cuttings must then be made on the 2 back-ends of the control rod pins. This option is due to the difficulty in knowing the orientation of the pins in the storage cases. The cutting lines are placed at approximately 1 m from the 2 back-ends of the pins. This approach does not allow a great optimization of the sorting, less than 50% of the length of the control rods can be saved from Intermediate Level Long-lived Waste storage. - With a simple dose rate measurement device, the knowledge of the orientation of the pins in the storage cases allows us to limit cuttings to the lower part of the control rods. Depending on the 'top to tail' cases, between approximately 50% and 75% of the length of the control rods can be saved from Intermediate Level Long-lived Waste storage. - With an accurate measurement device, the sorting can be based on a specific activity of Ag-108m. Over 4400 Bq/g of Ag-108m (corresponding to the Intermediate Level Long-lived Waste limit), the control rod pieces can be considered as a long-lived waste. The measurements must be made over the 2 back-ends of control rod pins to examine the cases of 'top to tail' storage. This approach allows a great optimization of the sorting. Depending on the history of irradiation, more than 75% of the length of the control rods can be saved from Intermediate Level Long-lived Waste storage. (author)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Multi-node and Multi-core Performance Studies of a Monte Carlo code RMC

Over the past 15 years the architecture of high-performance computing systems has become increasingly heterogeneous with individual computing cores being subdivided into nodes and even auxiliary co-processing units such as graphics processing units or the Intel many integrated core co-processors. In fact, future computer platforms is moving toward a larger number of nodes and cores with lower memory available per node. Today, several production Monte Carlo codes use some types of hybrid parallelism strategy that makes use of shared-memory parallelism within a computing node and message-passing parallelism between nodes, which enables the codes to utilize available computing resources as much as possible, both among and within computing nodes on a cluster. The so-called hybrid parallelization is also possible with Reactor Monte Carlo Code RMC by activating both MPI and OpenMP parallel algorithms together. On HPC' which typically consists of several or several-ten thousand nodes equipping 16-32 computing intra-cores per node, simulation of RMC can be carried out in the hybrid parallelization with the MPI inter-node parallelization and the OpenMP intra-node parallelization. RMC has adopted a hybrid message-passing and shared-memory approach to parallelism, which enables the code to utilize available computing resources, both among and within computing nodes on a cluster. Shared-memory parallelism is especially valuable for large-model simulations because it enables multiple compute cores within a node to share common model information such as the geometry description, material, cross section and tally data, thus reducing the memory usage per processor. The calculation on the Tianhe-2 supercomputer took 6144 cores, resulting in a rate of 173,314,000 neutrons/minute for BEAVRS benchmark. While pin-wise full core H-M benchmark burnup calculations with millions of depletion regions was selected using MPI/OpenMP parallelism, the speed of 6,144 cores reach 1,843,200 burnable regions per minute. Keeping up with the continuing trend for increases in the number of computing resources within modern HPC systems is a significant challenge for teams that develop and maintain high-performance MC radiation transport solvers. order to address this challenge, RMC has adopted a hybrid message-passing and shared-memory approach to parallelism, which enables the code to utilize available computing resources, both among and within computing nodes on a cluster. Shared-memory parallelism is especially valuable for large-model simulations because it enables multiple compute cores within a node to share common model information such as the geometry description, material and composition definitions, and cross section data, thus reducing the memory usage per processor. The parallel performance has been studied by using two complex and representative benchmarks, H-M and BEAVRS benchmark. All simulations were run on Intel Xeon E5-2692 12 core, 2.2 GHz processors at MilkyWay-2 Super Computer with up to 12,288 available computing cores. While employing MPI parallelism, excellent parallel efficiency is achieved even above 12,000 processors and RMC reaches the parallel efficiency of 96% on 12,288 cores for the pin-by-pin computation of the BEAVRS benchmark. While BEAVRS criticality benchmark was selected using MPI/OpenMP parallelism, the speed of 6,144 cores reach 173,314,000 particles per minute. While pin-wise full core H-M benchmark burnup calculations with millions of depletion regions was selected using MPI/OpenMP parallelism, the speed of 6,144 cores reach 1,843,200 burnable regions per minute. Results from these studies demonstrate that RMC, using the hybrid parallel model described in this paper, is able to handle pin-wise full core burnup calculations with millions of depletion regions and scales well through thousands of processors. (authors)

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Recent Metallic Fuel Data Recovery in FIPD

The Metallic Fuels Irradiation and Physics Database (FIPD) [1] is an organized collection of metallic fuel test pin data (U-xPu-yZr, = 0 ~ 28; y = 2 ~ 10) and documentation available to industry. FIPD mainly contains three types of data: (1) Fuel pin fabrication data, including fuel slug diameter, fuel slug length, cladding diameter, smear density, etc. (2) Fuel pin operation conditions, including axial distributions for power, temperatures, fluences, burnup, and isotopic densities, etc. and (3) Fuel pin post-irradiation examination (PIE) data, including fission gas release and gas chemistry, profilometry, and neutron radiography, etc. The operating conditions for pins with PIE data available in FIPD span significant ranges across key parameters. The fuel peak burnup extends from less than 5% up to 20 at%. The cladding peak temperature varies from about 490°C to 660°C. Finally, the cladding peak DPA shows a wide range from less than 5 to 120. These broad ranges reflect the diverse testing conditions and operational parameters captured in the available PIE data. More detail about FIPD can be found in ref. [2]. The database development is an ongoing effort covering metallic fuel experiments from the Experimental Breeder Reactor II (EBR-II) and the Fast Flux Test Facility (FFTF). As reported in the ref. [3, 4], most of the PIE data generated during the IFR program [5] has been collected, reviewed, processed, and integrated into FIPD. The most recently added PIE data can be found in ref. [4], which shows the collection of over 95% of the PIE data by the time of this paper. The recent improvements to the database are summarized in this paper.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Non-destructive Post-Transient Examination Results of the MOXTOP-1 Experiment

The MOXTOP-1 experiment has been assembled and irradiated in INL’s HFEF and TREAT facilities followed by disassembly of the experiment to enable initial post-transient examination. Results of neutron radiography of the fuel pin still in the THOR capsule were somewhat inconclusive due to the additional scatter and attenuation from the iron heat sink included in the design. Nonetheless, no obvious failure or fuel relocation could be identified in the radiography. Following disassembly of the fuel pin from the capsule, initial visual inspections were performed, and documented via images obtained through the hot cell window. No obvious signs of fuel failure were identified, indicating that the fuel pin remained intact during the transient. Some discoloration was observed near the middle of the fuel pin, likely corresponding to the fueled zone indicating that that region may have reached a relatively high temperature. Pre-transient, and post-transient profilometry of the fuel pin were performed and compared. Some additional strain displacement in the bottom portion of the fuel zone is identified, but remains well below 1%.

Mixed Oxide↗

Coupled effect of Cr and Al on interactions between a prismatic interstitial dislocation loop and an edge dislocation line in Fe-Cr-Al alloy

Segregation of alloying elements to a prismatic dislocation loop under irradiation is an important phenomenon in understanding the role of loops in radiation effects in alloys. In this work, various segregation sequences of Cr and Al atoms to a $\langle$100$\rangle$ and a 1/2 $\langle$111$\rangle$ prismatic dislocation loop in a Fe-Cr-Al alloy are explored using molecular dynamics method and ab initio energy calculation. Here, the results reveal that Cr can readily segregate to the loops while Al atoms cannot by themselves, but the segregated Cr atoms are able to promote Al segregation at the loops, defined as a coupled segregation of Cr and Al. After interacting with Cr and Al, a previously mobile 1/2 $\langle$111$\rangle$ loop becomes sessile. Al segregation through the coupled segregation process can further affect the pinning behavior of a dislocation loop to an edge dislocation motion. By varying the Al fraction in the segregated solutes, a nonlinear dependence of the pinning effect on dislocation motion is determined. At lower fractions, the pinning strength increases with the increasing Al fraction until Al fraction reaches a critical value of about 19%, above which the pinning strength decreases with further increase of Al fraction. All these results suggest that, in addition to the effect of Al on the surface resistance to oxidation, Al effect on the dislocation loop behavior is important to optimize the composition of Fe-Cr-Al alloys for their applications in accident tolerant fuel concepts.

36 MATERIALS SCIENCE↗

A review and prospects for Nb 3 Sn superconductor development

Nb 3 Sn superconductors have significant applications in constructing high-field (> 10 T) magnets. This article briefly reviews development of Nb 3 Sn superconductor and proposes prospects for further improvement. It is shown that significant improvement of critical current density (J c ) is needed for future accelerator magnets. After a brief review of the development of Nb 3 Sn superconductors, the factors controlling J c are summarized and correlated with their microstructure and chemistry. The non-matrix J c of Nb 3 Sn conductors is mainly determined by three factors: the fraction of current-carrying Nb 3 Sn phase in the non-matrix area, the upper critical field B c2 , and the flux-line pinning capacity. Then prospects to improve the three factors are discussed respectively. An analytic model was developed to show how the ratios of precursors determine the phase fractions after heat treatment, based on which it is predicted that the limit of current-carrying Nb 3 Sn fraction in subelements is ~65%. Then, since B c2 is largely determined by the Nb 3 Sn stoichiometry, a thermodynamic/kinetic theory was presented to show what essentially determines the Sn content of Nb 3 Sn conductors. This theory explains the influences of Sn sources and Ti addition on stoichiometry and growth rate of Nb 3 Sn layers. Next, to improve flux pinning, previous efforts in this community to introduce additional pinning centers (APC) to Nb 3 Sn wires are reviewed, and an internal oxidation technique is described. Lastly, prospects for further improvement of non-matrix J c of Nb 3 Sn conductors are discussed, and it is seen that the only opportunity for further significantly improving J c lies in improving the flux pinning.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Partial defect verification of spent fuel assemblies by PDET: Principle and field testing in Interim Spent fuel Storage Facility (CLAB) in Sweden

Here, the need for the development of a credible method and instrument for partial defect verification of spent fuel has been emphasized over a few decades in the safeguards communities as the diverted spent fuel pins can be the source of nuclear terrorism or devices. The need is increasingly more important and even urgent as many countries have started to transfer spent fuel to so called "difficult-to-access" areas such as dry storage casks, reprocessing or geological repositories. Partial defect verification is required by IAEA before spent fuel is placed into "difficult-to-access" areas. Earlier, Lawrence Livermore National Laboratory (LLNL) has reported the successful development of a new, credible partial defect verification method for pressurized water reactor (PWR) spent fuel assemblies without use of operator data, and further reported the validation experiments using commercial spent fuel assemblies with some missing fuel pins. The method was found to be robust as the method is relatively invariant to the characteristic variations of spent fuel assemblies such as initial fuel enrichment, cooling time, and burn-up. Since then, the PDET system has been designed and prototyped for 17×17 PWR spent fuel assemblies, complete with data acquisition software and acquisition electronics. In this paper, a summary description of the PDET development followed by results of the first successful field testing using the integrated PDET system and actual spent fuel assemblies performed in a commercial spent fuel storage site, known as Central Interim Spent fuel Storage Facility (CLAB) in Sweden will be presented. In addition to partial defect detection initial studies have determined that the tool can be used to verify the operator declared average burnup of the assembly as well as intra-assembly bunrup levels.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Single-Phase Jet Impingement Cooling for a Power-Dense Silicon Carbide Power Module

The adoption of silicon carbide (SiC) devices in the electric vehicle (EV) industry is increasing due to their superior performance over silicon devices. SiC devices enable further miniaturization of EV inverters, increasing their power density, which results in thermal management challenges. Here in this paper, the limits of single-phase jet impingement cooling are explored for an automotive SiC power module. We propose embedding pin fins in the direct-bonded-copper (DBC) substrate of the power module package using laser powder bed fusion additive manufacturing. The thermalhydraulic performance of the DBC-embedded pin fins is compared against folded fins that are directly soldered to the DBC substrate. A heat conduction analysis was conducted on a SiC package to determine the target heat transfer coefficient (HTC) for the heat sink. A water-ethylene glycol (WEG) jet impingement on the proposed concepts was studied using unit-cell models to achieve the target HTC. The studied designs put emphasis on the reliability and manufacturability requirements of the automotive industry. The thermal performance of DBC-embedded pin fins outperformed the DBC-soldered folded fins. The performance of the DBC-embedded pin fins is benchmarked against WEG-based cooling systems of commercial EVs. With the proposed cooling solution, we have shown a pathway of reducing the specific thermal resistance by 75% compared to BMW i3 thermal management system without any penalty on pressure drop or parasitic power.

33 ADVANCED PROPULSION SYSTEMS↗

Sandia National Laboratories Medical Isotope Reactor concept.

This report describes the Sandia National Laboratories Medical Isotope Reactor and hot cell facility concepts. The reactor proposed is designed to be capable of producing 100% of the U.S. demand for the medical isotope {sup 99}Mo. The concept is novel in that the fuel for the reactor and the targets for the {sup 99}Mo production are the same. There is no driver core required. The fuel pins that are in the reactor core are processed on a 7 to 21 day irradiation cycle. The fuel is low enriched uranium oxide enriched to less than 20% {sup 235}U. The fuel pins are approximately 1 cm in diameter and 30 to 40 cm in height, clad with Zircaloy (zirconium alloy). Approximately 90 to 150 fuel pins are arranged in the core in a water pool {approx}30 ft deep. The reactor power level is 1 to 2 MW. The reactor concept is a simple design that is passively safe and maintains negative reactivity coefficients. The total radionuclide inventory in the reactor core is minimized since the fuel/target pins are removed and processed after 7 to 21 days. The fuel fabrication, reactor design and operation, and {sup 99}Mo production processing use well-developed technologies that minimize the technological and licensing risks. There are no impediments that prevent this type of reactor, along with its collocated hot cell facility, from being designed, fabricated, and licensed today.

36 MATERIALS SCIENCE↗

Comet whole-core solution to a stylized 3-dimensional pressurized water reactor benchmark problem with UO{sub 2}and MOX fuel

A stylized pressurized water reactor (PWR) benchmark problem with UO{sub 2} and MOX fuel was used to test the accuracy and efficiency of the coarse mesh radiation transport (COMET) code. The benchmark problem contains 125 fuel assemblies and 44,000 fuel pins. The COMET code was used to compute the core eigenvalue and assembly and pin power distributions for three core configurations. In these calculations, a set of tensor products of orthogonal polynomials were used to expand the neutron angular phase space distribution on the interfaces between coarse meshes. The COMET calculations were compared with the Monte Carlo code MCNP reference solutions using a recently published an 8-group material cross section library. The comparison showed both the core eigenvalues and assembly and pin power distributions predicated by COMET agree very well with the MCNP reference solution if the orders of the angular flux expansion in the two spatial variables and the polar and azimuth angles on the mesh boundaries are 4, 4, 2 and 2. The mean and maximum differences in the pin fission density distribution ranged from 0.28%-0.44% and 3.0%-5.5%, all within 3-sigma uncertainty of the MCNP solution. These comparisons indicate that COMET can achieve accuracy comparable to Monte Carlo. It was also found that COMET's computational speed is 450 times faster than MCNP. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Application of fully ceramic microencapsulated fuels in light water reactors

This study performs a preliminary evaluation of the feasibility of incorporation of Fully Ceramic Microencapsulated (FCM) fuels in light water reactors (LWRs). In particular, pin cell, lattice, and full core analyses are carried out on FCM fuel in a pressurized water reactor (PWR). Using uranium-based fuel and Pu/Np-based fuel in TRistructural isotropic (TRISO) particle form, each fuel design was examined using the SCALE 6.1 analytical suite. In regards to the uranium-based fuel, pin cell calculations were used to determine which fuel material performed best when implemented in the fuel kernel as well as the size of the kernel and surrounding particle layers. The higher fissile material density of uranium mononitride (UN) proved to be favorable, while the parametric studies showed that the FCM particle fuel design with 19.75% enrichment would need roughly 12% additional fissile material in comparison to that of a standard UO{sub 2} rod in order to match the lifetime of an 18-month PWR cycle. As part of the fuel assembly design evaluations, fresh feed lattices were modeled to analyze the within-assembly pin power peaking. Also, a 'color-set' array of assemblies was constructed to evaluate power peaking and power sharing between a once-burned and a fresh feed assembly. In regards to the Pu/Np-based fuel, lattice calculations were performed to determine an optimal lattice design based on reactivity behavior, pin power peaking, and isotopic content. After obtaining a satisfactory lattice design, the feasibility of core designs fully loaded with Pu/Np FCM lattices was demonstrated using the NESTLE three-dimensional core simulator. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗