Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PERMITTIVITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

Glass Dielectrics in Extreme High‐Temperature Environment

Thin and flexible glass ribbons can be rolled into a film capacitor structures for power electronic circuits. Glass has excellent electrical properties and is a leading candidate to replace polymer films for high‐temperature applications. The dielectric properties of a low‐alkali aluminoborosilicate glass were characterized up to temperatures of 400°C. Low‐field permittivity values of 6 with dielectric loss below 0.01 were found for temperatures below 300°C. The dielectric breakdown strength exceeded 5 MV/cm for temperature of 400°C and high‐field polarization measurements showed that glass has over 95% energy efficiency at temperatures of 200°C, which is a target temperature for high‐temperature power electronic circuits driven by wide bandgap semiconductor devices.

Gao, Jun↗

Processing and characteristics of transparent Gd 3 TaO 7 polycrystalline ceramics

Transparent polycrystalline Gd 3 TaO 7 ceramics were successfully developed. A sol-gel process was used to synthesize Gd 3 TaO 7 powder with a uniform composition and an estimated average particle size of 100 nm. Simultaneous thermal gravimetric analysis and differential thermal analysis (TGA/DTA) was used to identify the decomposition sequence as a function of temperature for the as-synthesized sol-gel powders. Crystallization was confirmed by X-ray diffraction (XRD) and a single phase was achieved by calcining at 1000°C. The calcined powders were hot-pressed at 1400°C to achieve >96% theoretical density with closed pore structure followed by a hot isostatic pressing at 1400°C at 207 MPa to achieve a fully dense structure. Microstructural characterization shows a uniform grain size distribution with an average grain size of about 7 μm. In-line transmission measurements revealed high transparency in the red and infrared. Thermal conductivity was measured to be >1.6 W/mK at room temperature, decreasing to ~1.3 W/mK by 500°C. Dielectric properties remain stable with relative permittivity values just above 200 and loss tangents <0.005 up to 350°C.

36 MATERIALS SCIENCE↗

Modeling Microwave-Enhanced Chemical Vapor Infiltration Process for Preventing Premature Pore Closure

The chemical vapor infiltration (CVI) process involves infiltrating a porous preform with reacting gases that undergo chemical transformation at high temperatures to deposit the ceramic phase within the pores, ultimately leading to a dense composite. The conventional CVI process in composite manufacturing needs to follow an isothermal approach to minimize temperature differences between the external and internal surfaces of the preform, ensuring that reactive gases infiltrate internal pores before external surfaces seal. Here, this study addresses the challenge of premature pore closure in CVI processes through microwave heating. A frequency-domain microwave solver is developed in OpenFOAM to investigate volumetric heating mechanisms within the preform. Through numerical studies, we demonstrate the capability of microwave heating of creating an inside-out temperature inversion. This inversion accelerates reactions proximal to the preform center, effectively mitigating the risk of premature external pore closure and ensuring uniform densification. The results reveal a significant enhancement in temperature inversion when high-permittivity reflectors are incorporated to generate resonant waves. This microwave heating strategy is then coupled with high-fidelity direct numerical simulation (DNS) of reacting flow, enabling the analysis of resulting densification processes. The DNS includes detailed chemistry and realistic diffusion coefficients. The numerical results can be used to estimate the impact of microwave-induced temperature inversion on densification in productions.

42 ENGINEERING↗

Modeling Microwave-Enhanced Chemical Vapor Infiltration Process for Preventing Premature Pore Closure

The chemical vapor infiltration (CVI) process involves infiltrating a porous preform with reacting gases that undergo chemical transformation at high temperatures to deposit the ceramic phase within the pores, ultimately leading to a dense composite. The conventional CVI process in composite manufacturing needs to follow an isothermal approach to minimize temperature differences between the external and internal surfaces of the preform, ensuring that reactive gases infiltrate internal pores before external surfaces seal. This study addresses the challenge of premature pore closure in CVI processes through microwave heating. A frequency-domain microwave solver is developed in Open-FOAM to investigate volumetric heating mechanisms within the preform. Through numerical studies, we demonstrate the capability of microwave heating of creating an inside-out temperature inversion. This inversion accelerates reactions proximal to the preform center, effectively mitigating the risk of premature external pore closure and ensuring uniform densification. The results reveal a significant enhancement in temperature inversion when high-permittivity reflectors are incorporated to generate resonant waves. This microwave heating strategy is then coupled with high-fidelity direct numerical simulation (DNS) of reacting flow, enabling the analysis of resulting densification processes. The DNS simulation includes detailed chemistry and realistic diffusion coefficients. The numerical results can be used to estimate the impact of microwave-induced temperature inversion on densification in productions.

Ge, Wenjun↗

Hong–Ou–Mandel sensing via superradiant coupling of discrete fluorescent emitters

The Hong–Ou–Mandel (HOM) effect is a fascinating quantum phenomenon that defies classical explanation. Traditionally, remote nonlinear sources have been used to achieve coincident photons at the HOM beam splitter. Here, we suggest that the coincident emission source required for HOM interference can be created locally using superradiant near field coupled emitters positioned across the beam splitter gap. We show that sensitivity to permittivity changes in the beam splitter gap, and corresponding Fisher information can be substantially enhanced with HOM photon detection. Subsequently, we outline several strategies for integration of superradiant emitters with practical sensor systems. Taken together, these findings should pave a way for a wide array of near field HOM quantum sensors and novel quantum devices.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Multi-scale theory-assisted nano-engineering of plasmonic-organic hybrid electro-optic device performance

Multi-scale (correlated quantum and statistical mechanics) modeling methods have been advanced and employed to guide the improvement of organic electro-optic (OEO) materials, including by analyzing electric field poling induced electro-optic activity in nanoscopic plasmonic-organic hybrid (POH) waveguide devices. The analysis of in-device electro-optic activity emphasizes the importance of considering both the details of intermolecular interactions within organic electro-optic materials and interactions at interfaces between OEO materials and device architectures. Dramatic improvement in electro-optic device performance--including voltage-length performance, bandwidth, energy efficiency, and lower optical losses have been realized. These improvements are critical to applications in telecommunications, computing, sensor technology, and metrology. Multi-scale modeling methods illustrate the complexity of improving the electro-optic activity of organic materials, including the necessity of considering the trade-off between improving poling-induced acentric order through chromophore modification and the reduction of chromophore number density associated with such modification. Computational simulations also emphasize the importance of developing chromophore modifications that serve multiple purposes including matrix hardening for enhanced thermal and photochemical stability, control of matrix dimensionality, influence on material viscoelasticity, improvement of chromophore molecular hyperpolarizability, control of material dielectric permittivity and index of refraction properties, and control of material conductance. Consideration of new device architectures is critical to the implementation of chipscale integration of electronics and photonics and achieving the high bandwidths for applications such as next generation (e.g., 5G) telecommunications.

Engineering↗

Exogenous contrast agents for thermoacoustic imaging: An investigation into the underlying sources of contrast

Purpose: Thermoacoustic imaging at microwave excitation frequencies is limited by the low differential contrast exhibited by high water content tissues. To overcome this, exogenous thermoacoustic contrast agents based on gadolinium compounds, iron oxide, and single wall carbon nanotubes have previously been suggested and investigated. However, these previous studies did not fully characterize the electric, magnetic, and thermodynamic properties of these agents thus precluding identification of the underlying sources of contrast. To address this, measurements of the complex permittivity, complex permeability, DC conductivity, and Grüneisen parameter have been made. These measurements allowed the origins of the contrast provided by each substance to be identified. Methods: The electric and magnetic properties of the contrast agents were characterized at 3 GHz using two rectangular waveguide cavities. The DC conductivity was measured separately using a conductivity meter. Thermoacoustic signals were then acquired and compared to those generated in water. Finally, 3D electromagnetic simulations were used to decouple the different contributions to the absorbed power density. Results: It was found that the gadolinium compounds provided appreciable electric contrast but not originating from the gadolinium itself. The contrast was either due to dissociation of the gadolinium salt which increased ionic conductivity or its nondissociated polar fraction which increased dielectric polarization loss or a combination of both. In addition, very high concentrations were required to achieve appreciable contrast, to the extent that the Grüneisen parameter increased significantly and became a source of contrast. Iron oxide particles were found to produce low but measurable dielectric contrast due to dielectric polarization loss, but this is attributed to the coating of the particles not the iron oxide. Single wall carbon nanotubes did not provide measurable contrast of any type. Conclusions: It is concluded that gadolinium based contrast agents, iron oxide particles, and single walled carbon nanotubes have little intrinsic merit as thermoacoustic contrast agents. Simple electrolytes such as saline which yield high contrast based on ionic conductivity provide much higher dielectric contrast per unit solute concentration and are likely to be significantly more effective as contrast agents.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Control of polarization in bulk ferroelectrics by mechanical dislocation imprint

Defects are essential to engineering the properties of functional materials ranging from semiconductors and superconductors to ferroics. Whereas point defects have been widely exploited, dislocations are commonly viewed as problematic for functional materials and not as a microstructural tool. In this work, we developed a method for mechanically imprinting dislocation networks that favorably skew the domain structure in bulk ferroelectrics and thereby tame the large switching polarization and make it available for functional harvesting. The resulting microstructure yields a strong mechanical restoring force to revert electric field–induced domain wall displacement on the macroscopic level and high pinning force on the local level. This induces a giant increase of the dielectric and electromechanical response at intermediate electric fields in barium titanate [electric field–dependent permittivity (ε 33 ) ≈ 5800 and large-signal piezoelectric coefficient ( d 33 *) ≈ 1890 picometers/volt]. Dislocation-based anisotropy delivers a different suite of tools with which to tailor functional materials.

36 MATERIALS SCIENCE↗

Phase Diagram and Dielectric Properties of (1–x)Ba(Ti{sub 1–y}Zr{sub y})O{sub 3} · xPbTiO{sub 3} Ceramics

Ceramic (1–x)Ba(Ti1–yZry)O{sub 3} · xPbTiO{sub 3} (0 ≤ x, у ≤ 1) samples have been characterized by X-ray diffraction and dielectric measurements. The results have been used to map out the phase diagram of the system, which demonstrates the variation in the phase composition of the samples. It has been shown that, in the composition regions adjacent to the BaTiO{sub 3}–PbTiO{sub 3} side and BaZrO{sub 3} corner of the composition triangle, the samples consist of perovskite solid solutions that have tetragonal and cubic structures, respectively, at room temperature. In the intermediate composition region, the samples consist of different perovskite solid solutions similar in composition and structure. We have obtained composition dependences of the unit-cell symmetry and parameters for the solid solutions, their ferroelectric Curie temperature T{sub C}, characteristic dielectric relaxation temperatures, dielectric permittivity ε, and dielectric loss tangent tanδ (at temperatures from 100 to 800 K and frequencies from 25 to 106 Hz) and analyzed the evolution of their dielectric properties with increasing BaZrO{sub 3} content: from ferroelectric to properties of ferroelectric relaxors, reentrant relaxors, and dielectric relaxors of the dipole glass type.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The Effect of Specular Reflectances on the Interaction of an Electromagnetic E Wave with a Thin Metal Film Placed between Two Dielectric Media

The interaction of an electromagnetic E wave with a thin metal film placed between two dielectric media is calculated in the case of different specular reflectances q{sub 1} and q{sub 2} for the reflection of electrons from the surface of the thin metal layer, in the case of variations in the values of dielectric permittivities ε{sub 1} and ε{sub 2} of the media, and in the case of different values of angle of incidence θ of the electromagnetic wave. The behavior of reflection coefficient R, transmission coefficient T, and absorption coefficient A in relation to the frequency of the external field is analyzed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Plasmon resonances in a two-dimensional lattice of metal particles in a dielectric layer: Structural and polarization properties

The results of experimental and theoretical investigation of planar two-dimensional (2D) samples of plasmon structures are presented. The samples represent a 2D lattice of gold nanoparticles embedded in a thin dielectric layer and are studied by atomic force microscopy (AFM) and optical methods. Absorption bands associated with the excitation of various surface plasmon resonances (SPR) are interpreted. It is found that the choice of the mutual orientation of the polarization plane and the edge of the unit cell of the 2D lattice determines the spectral position of the lattice surface plasmon resonance (LSPR) related to the lattice period. It is shown that the interaction of p- and s-polarized light with a 2D lattice of nanoparticles is described by the dipole–dipole interaction between nanoparticles embedded in a medium with effective permittivity. Analysis of the spectra of ellipsometric parameters allows one to determine the amplitude and phase anisotropy of transmission, which is a consequence of the imperfection of the 2D lattice of samples.

36 MATERIALS SCIENCE↗

Ab initio calculations of exciton effects in optical spectra of an α-B{sub 12} crystal

The dielectric functions and energy loss spectrum of electrons of a rhombohedral α-B{sub 12} crystal are studied both in the single-particle and many-particle approximations using Bethe–Salpeter equations. The opposite roles of different contributions to exciton effects are discussed. The anisotropy of dielectric functions is shown, which demonstrates their high sensitivity with respect to the three-dimensional packing of icosahedrons. The influence of the coherent mixing of electronic and exciton states on the redistribution of oscillator strengths is found. The position of the plasmon of valence electrons and the high-frequency permittivity are found to be consistent with experimental data. The correlation between the distribution of oscillator strengths and features of the density of electronic states is discussed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Experimental studies of the effects of atomic ordering in epitaxial Ga{sub x}In{sub 1–} {sub x}P alloys on their optical properties

The properties of epitaxial Ga{sub x}In{sub 1–} {sub x}P alloys with an ordered arrangement of atoms in the crystal lattice are studied by a number of spectroscopic methods. The alloys are grown by metal-organic chemical vapor deposition onto single-crystal GaAs(100) substrates. It is shown that, under conditions of the coherent growth of an ordered Ga{sub x}In{sub 1–} {sub x}P alloy on a GaAs(100) substrate, atomic ordering results in radical modifications of the optical properties of the semiconductor compared to the properties of disordered alloys. Among these modifications are a decrease in the band gap and an increase in the luminescence intensity. From the data of dispersion analysis of the infrared dispersion spectra and from ultraviolet spectroscopy data obtained in the transmittance–reflection mode of measurements, the basic optical characteristics, specifically, the dispersion of the refractive index and the high-frequency permittivity of Ga{sub x}In{sub 1–} {sub x}P alloys with ordering are determined. All of the experimental data are in good agreement with the developed theoretical concepts.

36 MATERIALS SCIENCE↗

Infrared Reflection Spectra of Pb{sub 1–x}Sn{sub x}Se (x = 0.2, 0.34) Topological Insulator Films on a ZnTe/GaAs Substrate and the Vibrational Modes of Multilayer Structures

The reflectance spectra of the topological insulator Pb{sub 1–x}Sn{sub x}Se (x = 0.2, 0.34) films grown by molecular-beam epitaxy on a ZnTe/GaAs substrate are measured in the range of 12–2500 cm{sup –1} at room temperature. Using dispersion analysis, the frequencies of transverse optical phonons, plasma frequencies, highfrequency permittivities, and layer thicknesses are determined. In the quasi-steady-state approximation, the interface mode frequencies of the four-layer structure are calculated as a function of the overlap parameter χ{sub 1} (0 ≤ χ{sub 1} ≤ 1). The parameter describes the degree of overlap of two interface modes localized at planes bounding the layer to the right and left. The existence of interacting interface modes in the structure makes its spectrum different from the sum of component spectra. These differences manifest themselves in the experiment. The conditions of the interaction of interface modes with IR radiation are discussed.

36 MATERIALS SCIENCE↗

Impact of UV Pulsed Laser Radiation and of the Electron Flow on Dielectric States of Polymer Composite Nanomaterial Based on LDPE Matrix

The influence of the soft electron flow and irradiating pulsed UV laser on dielectric states of polymer composite nanomaterial based on LDPE matrix is experimentally studied. It was shown that irradiation of the samples LDPE–ZnO by electron beam (10 keV) for 10–15 minutes gives rise the appearance of the horizontal portion of the temperature dependence of capacitance (permittivity) and to memory effect (slow relaxation of dielectric situation within a few days). Irradiation with pulsed UV laser of the LDPE–CdS sample allows you to switch into a conducting state and return it to their original state upon application of a weak electric field. The observed phenomena may find practical applications for the polymer electronic memories and switching devices.

36 MATERIALS SCIENCE↗

Microwave Microscopy and Its Applications

Understanding the nanoscale electrodynamic properties of a material at microwave frequencies is of great interest for materials science, condensed matter physics, device engineering, and biology. With specialized probes, sensitive detection electronics, and improved scanning platforms, microwave microscopy has become an important tool for cutting-edge materials research in the past decade. In this article, we review the basic components and data interpretation of microwave imaging and its broad range of applications. In addition to the general-purpose mapping of permittivity and conductivity, microwave microscopy is now exploited to perform quantitative measurements on semiconductor devices, photosensitive materials, ferroelectric domains and domain walls, and acoustic-wave systems. Implementation of the technique in low-temperature and high-magnetic-field chambers has also led to major discoveries in quantum materials with strong correlation and topological order. We conclude the review with an outlook of the ultimate resolution, operation frequency, and future industrial and academic applications of near-field microwave microscopy.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Electrophoretic Deposition of Platinum Nanoparticles using Ethanol-Water Mixtures Significantly Reduces Neural Electrode Impedance

We report platinum electrodes are critical components in many biomedical devices, an important example being implantable neural stimulation or recording electrodes. However, upon implantation, scar tissue forms around the electrode surface, causing unwanted deterioration of the electrical contact. We demonstrate that sub-monolayer coatings of platinum nanoparticles (PtNPs) applied to 3D neural electrodes by electrophoretic deposition (EPD) can enhance the electrode's active surface area and significantly lower its impedance. In this work we use ethanol-water mixtures as the EPD solvent, in contrast to our previous studies carried out in water. We show that EPD coating in 30 vol.% ethanol improves the device's electrochemical performance. Computational mesoscale multiparticle simulations were for the first time applied to PtNP-on-Pt EPD, revealing correlations between ethanol concentration, electrochemical properties, and coating homogeneity. Thereto, this optimum ethanol concentration (30 vol.%) balances two opposing trends: (i) the addition of ethanol reduces water splitting and gas bubble formation, which benefits surface coverage, and (ii) increased viscosity and reduced permittivity occur at high ethanol concentrations, which impair the coating quality and favoring clustering. A seven-fold increase in active surface area and significantly reduced in vitro impedance of the nano-modified neural stimulation electrode surfaces highlight the influence of ethanol-water mixtures in PtNP EPD.

36 MATERIALS SCIENCE↗

Communication—First-Principles Simulations of LiPF 6 Decomposition in Ethylene Carbonate-Based Electrolytes

We revisit a theoretical result by Okamoto (2013 Journal of The Electrochemical Society , 160 , A404) who calculated the energy barrier for the decomposition of lithium hexafluorophosphate (LiPF 6 ) into LiF + PF 5 when solvated in Ethylene carbonate (EC)-based electrolyte. Using different numerical techniques to discretize the Density Functional Theory (DFT) equations, and different continuum solvation models with the same dielectric constant, our results largely confirm the original calculation. However, simulations with a higher dielectric permittivity value, closer to that of EC, show a lower energy barrier. More importantly, First-Principles simulations with an explicit solvent show a substantially lower energy barrier.

25 ENERGY STORAGE↗