Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNETRONS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

Ferromagnetism and ferroelectricity in epitaxial BiMnO{sub 3} ultra-thin films

We studied the ferroelectric and ferromagnetic properties of compressive strained and unstrained BiMnO{sub 3} thin films grown by rf-magnetron sputtering. BiMnO{sub 3} samples exhibit a two-dimensional cube-on-cube growth mode and a pseudo-cubic structure up to a thickness of 15 nm and of 25 nm when deposited on (001) SrTiO{sub 3} and (110) DyScO{sub 3}, respectively. Above these thicknesses, we observe a switching to a three-dimensional island growth mode and a simultaneous structural change to a (00l) oriented monoclinic unit cell. While ferromagnetism is observed below a T{sub C} ≈ 100 K for all samples, signatures of room temperature ferroelectricity were found only in the pseudo-cubic ultra-thin films, indicating a correlation between electronic and structural orders.

36 MATERIALS SCIENCE↗

Infrared optical properties of amorphous and nanocrystalline Ta{sub 2}O{sub 5} thin films

The optical constants of tantalum pentoxide (Ta{sub 2}O{sub 5}) are determined in a broad spectral region from the visible to the far infrared. Ta{sub 2}O{sub 5} films of various thicknesses from approximately 170 to 1600 nm are deposited using reactive magnetron sputtering on Si substrates. X-ray diffraction shows that the as-deposited films are amorphous, and annealing in air at 800 °C results in the formation of nanocrystalline Ta{sub 2}O{sub 5}. Ellipsometry is used to obtain the dispersion in the visible and near-infrared. Two Fourier-transform infrared spectrometers are used to measure the transmittance and reflectance at wavelengths from 1 to 1000 μm. The surface topography and microstructure of the samples are examined using atomic force microscopy, confocal microscopy, and scanning electron microscopy. Classical Lorentz oscillators are employed to model the absorption bands due to phonons and impurities. A simple model is introduced to account for light scattering in the annealed films, which contain micro-cracks. For the unannealed samples, an effective-medium approximation is used to take into account the adsorbed moisture in the film and a Drude free-electron term is also added to model the broad background absorption.

36 MATERIALS SCIENCE↗

Design of a high-power, high-gain, 2nd harmonic, 22.848 GHz gyroklystron

In this paper we consider the design of a four-cavity, high-gain K-band gyroklystron experiment for high gradient structure testing. The frequency doubling gyroklystron utilizes a beam voltage of 500 kV and a beam current of 200 A from a magnetron injection gun (MIG) originally designed for a lower-frequency device. The microwave circuit features input and gain cavities in the circular TE{sub 011} mode and penultimate and output cavities that operate at the second harmonic in the TE{sub 021} mode. We investigate the MIG performance and study the behavior of the circuit for different values of perpendicular to parallel velocity ratio (α= V{sub ⊥}/ V{sub z}). This microwave tube is expected to be able to produce at least 20 MW of power in 1μs pulses at a repetition rate of at least 120 Hz. A maximum efficiency of 26% and a large signal gain of 58 dB under zero-drive stable conditions were simulated for a velocity ratio equal to 1.35.

43 PARTICLE ACCELERATORS↗

An (ultra) high-vacuum compatible sputter source for oxide thin film growth

A miniaturised CF-38 mountable sputter source for oxide and metal thin film preparation with enhanced high-vacuum and ultra-high-vacuum compatibility is described. The all home-built sputtering deposition device allows a high flexibility also in oxidic sputter materials, suitable deposition rates for preparation of films in the nm- and the sub-monolayer regime and excellent reliability and enhanced cleanliness for usage in UHV chambers. For a number of technologically important – yet hardly volatile – materials, the described source represents a significant improvement over thermal deposition techniques like electron-beam- or thermal evaporation, as especially the latter are no adequate tool to prepare atomically clean layers of refractory oxide materials. Furthermore, it is superior to commercially available magnetron sputter devices, especially for applications, where highly reproducible sub-monolayer thin film preparation under very clean UHV conditions is required (e.g., for studying phase boundary effects in catalysis). The device in turn offers the usage of a wide selection of evaporation materials and special target preparation procedures also allow the usage of pressed oxide powder targets. To prove the performance of the sputter-source, test preparations with technologically relevant oxide components, comprising ZrO{sub 2} and yttrium-stabilized ZrO{sub 2}, have been carried out. A wide range of characterization methods (electron microscopy, X-ray photoelectron spectroscopy, low-energy ion scattering, atomic force microscopy, and catalytic testing) were applied to demonstrate the properties of the sputter-deposited thin film systems.

36 MATERIALS SCIENCE↗

Orientation-dependent piezoelectric properties in lead-free epitaxial 0.5BaZr{sub 0.2}Ti{sub 0.8}O{sub 3}-0.5Ba{sub 0.7}Ca{sub 0.3}TiO{sub 3} thin films

Orientation-engineered 0.5BaZr{sub 0.2}Ti{sub 0.8}O{sub 3}-0.5Ba{sub 0.7}Ca{sub 0.3}TiO{sub 3} (BZT-BCT) thin films were deposited on La{sub 0.7}Sr{sub 0.3}MnO{sub 3}-coated SrTiO{sub 3} single-crystalline (001), (110), and (111) substrates by off-axis radio-frequency magnetron sputtering. X-ray diffraction confirmed a highly epitaxial growth of all the as-deposited films. It is believed the strong orientation dependence of ferroelectric and piezoelectric properties on the films is attributed to the relative alignment of crystallites and spontaneous polarization vector. The optimal ferroelectric response lies in the [001] direction, whereas a comparatively large effective piezoelectric coefficient d{sub 33,eff} of 100.1 ± 5 pm/V was attained in [111] BZT-BCT thin film, suggesting its potential application for high-performance lead-free piezoelectric devices.

36 MATERIALS SCIENCE↗

Extraordinarily large perpendicular magnetic anisotropy in epitaxially strained cobalt-ferrite Co{sub x}Fe{sub 3−x}O{sub 4}(001) (x = 0.75, 1.0) thin films

Perpendicular magnetic anisotropy (PMA) of cobalt-ferrite Co{sub x}Fe{sub 3-x}O{sub 4} (x = 0.75 and 1.0) epitaxial thin films grown on MgO (001) by a reactive magnetron sputtering technique was investigated. The saturation magnetization was found to be 430 emu/cm{sup 3} for x = 0.75, which is comparable to that of bulk CoFe{sub 2}O{sub 4} (425 emu/cm{sup 3}). Torque measurements afforded PMA constants of K{sub u}{sup eff}=9.0 Merg/cm{sup 3} (K{sub u}=10.0 Merg/cm{sup 3}) and K{sub u}{sup eff}=9.7 Merg/cm{sup 3} for x = 0.75 and 1.0, respectively. The value of K{sub u}{sup eff} extrapolated using Miyajima's plot was as high as 14.7 Merg/cm{sup 3} for x = 1.0. The in-plane four-fold magnetic anisotropy was evaluated to be 1.6 Merg/cm{sup 3} for x = 0.75. X-ray diffraction measurement revealed our films to be pseudomorphically strained on MgO (001) with a Poisson ratio of 0.4, leading to a considerable in-plane tensile strain by which the extraordinarily large PMA could be accounted for.

36 MATERIALS SCIENCE↗

Electronic transport in heavily doped Ag/n-Si composite films

Hall measurements characterized Ag/n-Si composite films 1 micron thick produced by magnetron co-sputtering onto high resistivity Si (111) substrates at 550°C. The targets were Ag and n-type Si doped with 3 × 10{sup 19}/cm{sup 3} of antimony. Films were prepared with 13, 16 and 22 at. % Ag and measured over a temperature range 77–500°K. Conduction takes place at low temperatures by variable rang hopping in localized states at the Fermi level and by thermal activation over grain boundaries at higher temperatures. The Log Resistivity vs 1/kT curves for the three Ag concentrations vary in a similar manner, but decrease in magnitude with increasing Ag due to the smaller number of grain boundaries between Ag nanoparticles occurring with increasing Ag concentration. At low temperatures Hall mobilities are essentially independent of temperature as the carrier densities for the three Ag concentrations are constant from 77 to slightly under 300°K with resistivities varying by small amounts. The mobilities at all Ag concentrations increase with temperature and approach each other as the effects of grain boundaries become less important. This work presents for the first time the effects of metal particles embedded in a semiconductor on the transport properties of carriers in the semiconductor. Though these effects are for a given average particle size most of the results are expected to hold over a range of particle sizes. Free electrons produced in films containing 13 and 16 at. % Ag result in concentrations of 1.5 × 10{sup 19}/cm{sup 3}, one half the antimony doping, while those with 22 at. % Ag, the carrier concentrations are three orders of magnitude higher. These constant carrier concentrations are due to the metal-insulator transition that occurs in doped crystalline and polycrystalline silicon for carrier densities n{sub c} >3.9 × 10{sup 18}/cm{sup 3}. The three orders of magnitude higher carrier concentration produced in films with 22 at. % Ag is argued to be due to doping of the Si matrix by the Ag nanoparticles at this concentration, a doping effect previously observed in ErAs in InGaAs. A discussion of this doping effect is presented that is in keeping with the experimental observations though other factors such as particle size effects need further experimental confirmation. Thermal activation energies and grain boundary barrier heights were obtained from resistivity and Hall mobility data. The barrier heights of 0.360, 0.390 and 0.470 eV measured for films with Ag concentrations of 13, 16 and 22 at. % Ag respectively, are quite high compared to those obtained by other methods used for producing polycrystalline Si (10-100 mev) and need to be considerably reduced in order to increase the efficiency of the detectors for which these Ag/n-Si composite films will be used. Thermal annealing of as-deposited films is suggested as one means to accomplish this result.

36 MATERIALS SCIENCE↗

Particle beam experiments for the analysis of reactive sputtering processes in metals and polymer surfaces

A beam experiment is presented to study heterogeneous reactions relevant to plasma-surface interactions in reactive sputtering applications. Atom and ion sources are focused onto the sample to expose it to quantified beams of oxygen, nitrogen, hydrogen, noble gas ions, and metal vapor. The heterogeneous surface processes are monitored in situ by means of a quartz crystal microbalance and Fourier transform infrared spectroscopy. Two examples illustrate the capabilities of the particle beam setup: oxidation and nitriding of aluminum as a model of target poisoning during reactive magnetron sputtering, and plasma pre-treatment of polymers (PET, PP)

36 MATERIALS SCIENCE↗

Bandgap widening in thermochromic Mg-doped VO{sub 2} thin films: Quantitative data based on optical absorption

Thermochromic Mg-doped VO{sub 2} films were deposited by reactive direct current magnetron sputtering onto heated glass and carbon substrates. Elemental compositions were inferred from Rutherford backscattering. Optical bandgaps were obtained from spectral transmittance and reflectance measurements—from both the film side and the back side of the samples—and ensuing determination of absorption coefficients. The bandgap of Mg-doped films was found to increase by 3.9 ± 0.5 eV per unit of atom ratio Mg/(Mg + V) for 0 < Mg/(Mg + V) < 0.21. The presence of ∼0.45 at. % Si enhanced the bandgap even more.

36 MATERIALS SCIENCE↗

X-ray absorption spectroscopy and magnetic circular dichroism studies of L1{sub 0}-Mn-Ga thin films

Tetragonally distorted Mn{sub 3−x}Ga{sub x} thin films with 0.1<x<2 show a strong perpendicular magnetic anisotropy and low magnetization and thus have the potential to serve as electrodes in spin transfer torque magnetic random access memory. Because a direct capping of these films with MgO is problematic due to oxide formation, we examined the influence of a CoFeB interlayer and of two different deposition methods for the MgO barrier on the formation of interfacial Mn-O for Mn{sub 62}Ga{sub 38} by element specific X-ray absorption spectroscopy (XAS) and magnetic circular dichroism (XMCD). A highly textured L1{sub 0} crystal structure of the Mn-Ga films was verified by X-ray diffraction measurements. For samples with e-beam evaporated MgO barrier no evidence for Mn-O was found whereas in samples with magnetron sputtered MgO, Mn-O was detected, even for the thickest interlayer thickness. Both XAS and XMCD measurements showed an increasing interfacial Mn-O amount with decreasing CoFeB interlayer thickness. Additional element specific full hysteresis loops determined an out-of-plane magnetization axis for the Mn and Co, respectively.

36 MATERIALS SCIENCE↗

Improving electrical performance and bias stability of HfInZnO-TFT with optimizing the channel thickness

RF magnetron sputtered HfInZnO film and atomic layer deposition (ALD) Al{sub 2}O{sub 3} film were employed for thin film transistors (TFTs) as channel layer and gate insulator, respectively. To achieve HfInZnO-TFT with high performance and good bias stability, the thickness of HfInZnO active layer was optimized. The performance of HfInZnO-TFTs was found to be thickness dependent. As the HfInZnO active layer got thicker, the leakage current greatly increased from 1.73 × 10{sup −12} to 2.54 × 10{sup −8} A, the threshold voltage decreased from 7.4 to −4.7 V, while the subthreshold swing varied from 0.41 to 1.07 V/decade. Overall, the HfInZnO film showed superior performance, such as saturation mobility of 6.4 cm{sup 2}/V s, threshold voltage of 4.2 V, subthreshold swing of 0.43 V/decade, on/off current ratio of 3 × 10{sup 7} and V{sub th} shift of 3.6 V under V{sub GS}= 10 V for 7200 s. The results demonstrate the possibility of fabricating TFTs using HfInZnO film as active layer and using ALD Al{sub 2}O{sub 3} as gate insulator.

36 MATERIALS SCIENCE↗

Effects of substrate temperature, substrate orientation, and energetic atomic collisions on the structure of GaN films grown by reactive sputtering

The combined effects of substrate temperature, substrate orientation, and energetic particle impingement on the structure of GaN films grown by reactive radio-frequency magnetron sputtering are investigated. Monte-Carlo based simulations are employed to analyze the energies of the species generated in the plasma and colliding with the growing surface. Polycrystalline films grown at temperatures ranging from 500 to 1000 °C clearly showed a dependence of orientation texture and surface morphology on substrate orientation (c- and a-plane sapphire) in which the (0001) GaN planes were parallel to the substrate surface. A large increase in interplanar spacing associated with the increase in both a- and c-parameters of the hexagonal lattice and a redshift of the optical bandgap were observed at substrate temperatures higher than 600 °C. The results showed that the tensile stresses produced during the film's growth in high-temperature deposition ranges were much larger than the expected compressive stresses caused by the difference in the thermal expansion coefficients of the film and substrate in the cool-down process after the film growth. The best films were deposited at 500 °C, 30 W and 600 °C, 45 W, which corresponds to conditions where the out diffusion from the film is low. Under these conditions the benefits of the temperature increase because of the decrease in defect density are greater than the problems caused by the strongly strained lattice that occurr at higher temperatures. The results are useful to the analysis of the growth conditions of GaN films by reactive sputtering.

36 MATERIALS SCIENCE↗

Converse magnetoelectric coupling in NiFe/Pb(Mg{sub 1/3}Nb{sub 2/3})O{sub 3}–PbTiO{sub 3} nanocomposite thin films grown on Si substrates

Multiferroic NiFe (∼30 nm)/Pb(Mg{sub 1/3}Nb{sub 2/3})O{sub 3}–PbTiO{sub 3}(PMN–PT, ∼220 nm) bilayered thin films were grown on common Pt/Ti/SiO{sub 2}/Si substrates by a combination of off-axis magnetron sputtering and sol-gel spin-coating technique. By using AC-mode magneto-optical Kerr effect technique, the change in the Kerr signal (magnetization) of the NiFe upon applying a low-frequency AC voltage to the PMN–PT film was in situ acquired at zero magnetic field. The obtained Kerr signal versus voltage loop essentially tracks the electromechanical strain curve of the PMN–PT thin film, clearly demonstrating a strain-mediated converse magnetoelectric coupling, i.e., voltage-modulated magnetization, in the NiFe/PMN–PT nanocomposite thin films.

36 MATERIALS SCIENCE↗

Electron/phonon coupling in group-IV transition-metal and rare-earth nitrides

Transport electron/phonon coupling parameters and Eliashberg spectral functions α{sub tr}{sup 2}F(ℏω) are determined for group-IV transition-metal (TM) nitrides TiN, ZrN, and HfN, and the rare-earth (RE) nitride CeN using an inversion procedure based upon temperature-dependent (4 < T < 300 K) resistivity measurements of high-crystalline-quality stoichiometric epitaxial films grown on MgO(001) by magnetically-unbalanced reactive magnetron sputtering. Transport electron/phonon coupling parameters λ{sub tr} vary from 1.11 for ZrN to 0.82 for HfN, 0.73 for TiN, and 0.44 for CeN. The small variation in λ{sub tr} among the TM nitrides and the weak coupling in CeN are consistent with measured superconducting transition temperatures 10.4 (ZrN), 9.18 (HfN), 5.35 (TiN), and <4 K for CeN. The Eliashberg spectral function describes the strength and energy spectrum of electron/phonon coupling in conventional superconductors. Spectral peaks in α{sup 2}F(ℏω), corresponding to regions in energy-space for which electrons couple to acoustic ℏω{sub ac} and optical ℏω{sub op} phonon modes, are centered at ℏω{sub ac} = 33 and ℏω{sub op} = 57 meV for TiN, 25 and 60 meV for ZrN, 18 and 64 meV for HfN, and 21 and 39 meV for CeN. The acoustic modes soften with increasing cation mass; optical mode energies remain approximately constant for the TM nitrides, but are significantly lower for the RE nitride due to a lower interatomic force constant. Optical/acoustic peak-intensity ratios are 1.15 ± 0.1 for all four nitrides, indicating similar electron/phonon coupling strengths α{sub tr}(ℏω) for both modes.

36 MATERIALS SCIENCE↗

Self-organization during growth of ZrN/SiN{sub x} multilayers by epitaxial lateral overgrowth

ZrN/SiN{sub x} nanoscale multilayers were deposited on ZrN seed layers grown on top of MgO(001) substrates by dc magnetron sputtering with a constant ZrN thickness of 40 Å and with an intended SiN{sub x} thickness of 2, 4, 6, 8, and 15 Å at a substrate temperature of 800 °C and 6 Å at 500 °C. The films were investigated by X-ray diffraction, high-resolution scanning transmission electron microscopy, and energy dispersive X-ray spectroscopy. The investigations show that the SiN{sub x} is amorphous and that the ZrN layers are crystalline. Growth of epitaxial cubic SiN{sub x}—known to take place on TiN(001)—on ZrN(001) is excluded to the monolayer resolution of this study. During the course of SiN{sub x} deposition, the material segregates to form surface precipitates in discontinuous layers for SiN{sub x} thicknesses ≤6 Å that coalesce into continuous layers for 8 and 15 Å thickness at 800 °C, and for 6 Å at 500 °C. The SiN{sub x} precipitates are aligned vertically. The ZrN layers in turn grow by epitaxial lateral overgrowth on the discontinuous SiN{sub x} in samples deposited at 800 °C with up to 6 Å thick SiN{sub x} layers. Effectively a self-organized nanostructure can be grown consisting of strings of 1–3 nm large SiN{sub x} precipitates along apparent column boundaries in the epitaxial ZrN.

36 MATERIALS SCIENCE↗

Design of a new electron cyclotron resonance ion source at Oshima National College of Maritime Technology

A new electron cyclotron resonance ion/plasma source has been designed and will be built at Oshima National College of Maritime Technology by early 2014. We have developed an ion source that allows the control of the plasma parameters over a wide range of electron temperatures for material research. A minimum-B magnetic field composed of axial mirror fields and radial cusp fields was designed using mainly Nd-Fe-B permanent magnets. The axial magnetic field can be varied by three solenoid coils. The apparatus has 2.45 GHz magnetron and 2.5–6.0 GHz solid-state microwave sources.

43 PARTICLE ACCELERATORS↗

In-situ x-ray diffraction study of the growth of highly strained epitaxial BaTiO{sub 3} thin films

In-situ synchrotron x-ray diffraction was performed during the growth of BaTiO{sub 3} thin films on SrTiO{sub 3} substrates using both off-axis RF magnetron sputtering and pulsed laser deposition techniques. It was found that the films were ferroelectric during the growth process, and the presence or absence of a bottom SrRuO{sub 3} electrode played an important role in the growth of the films. Pulsed laser deposited films on SrRuO{sub 3} displayed an anomalously high tetragonality and unit volume, which may be connected to the previously predicted negative pressure phase of BaTiO{sub 3}.

36 MATERIALS SCIENCE↗

Effect of substrate temperature on the magnetic properties of epitaxial sputter-grown Co/Pt

Epitaxial Co/Pt films have been deposited by dc-magnetron sputtering onto heated C-plane sapphire substrates. X-ray diffraction, the residual resistivity, and transmission electron microscopy indicate that the Co/Pt films are highly ordered on the atomic scale. The coercive field and the perpendicular magnetic anisotropy increase as the substrate temperature is increased from 100–250 °C during deposition of the Co/Pt. Measurement of the domain wall creep velocity as a function of applied magnetic field yields the domain wall pinning energy, which scales with the coercive field. Evidence for an enhanced creep velocity in highly ordered epitaxial Co/Pt is found.

36 MATERIALS SCIENCE↗