Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Land Use Control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59
All sourcesNASA NTRSDOE OSTI
NASA NTRS2015

Handling Qualities of Large Rotorcraft in Hover and Low Speed

According to a number of system studies, large capacity advanced rotorcraft with a capability of high cruise speeds (approx.350 mph) as well as vertical and/or short take-off and landing (V/STOL) flight could alleviate anticipated air transportation capacity issues by making use of non-primary runways, taxiways, and aprons. These advanced aircraft pose a number of design challenges, as well as unknown issues in the flight control and handling qualities domains. A series of piloted simulation experiments have been conducted on the NASA Ames Research Center Vertical Motion Simulator (VMS) in recent years to systematically investigate the fundamental flight control and handling qualities issues associated with the characteristics of large rotorcraft, including tiltrotors, in hover and low-speed maneuvering.

Large Rotorcraft↗
NASA NTRS2019

Lunar Lander Handling Qualities

Handling qualities are those characteristics of a flight vehicle that govern the ease and precision with which a pilot can perform a flying task. A series of piloted experiments were conducted in the NASA Ames Vertical Motion Simulator (VMS) between 2007 and 2010, to study handling qualities for the Altair and Orion spacecraft that were being designed for NASA's Constellation program. Four Apollo astronauts and over 30 Space Shuttle astronauts participated in these studies and provided evaluations of spacecraft handling qualities for various flying tasks. The knowledge gained from these studies may be used to guide the design of flight control systems and cockpit displays, and/or key design trade-offs between candidate configurations of piloted spacecraft. This seminar provides an overview of three handling qualities studies focused on the lunar landing task for the Apollo Lunar Module and the Altair lunar lander. These studies have already been published in journals and presented at conferences.

Lunar Lander; Handling Qualities↗
NASA NTRS2019

Climates of Warm Earth-Like Planets III: Fractional Habitability from a Water Cycle Perspective

The habitable fraction of a planet's surface is important for the detectability of surface biosignatures. The extent and distribution of habitable areas are influenced by external parameters that control the planet's climate, atmospheric circulation, and hydrological cycle. We explore these issues using the ROCKE-3D general circulation model, focusing on terrestrial water fluxes and thus the potential for the existence of complex life on land. Habitability is examined as a function of insolation and planet rotation for an Earth-like world with zero obliquity and eccentricity orbiting the Sun. We assess fractional habitability using an aridity index that measures the net supply of water to the land. Earth-like planets become "superhabitable" (a larger habitable surface area than Earth) as insolation and day-length increase because their climates become more equable, reminiscent of past warm periods on Earth when complex life was abundant and widespread. The most slowly rotating, most highly irradiated planets, though, occupy a hydrological regime unlike any on Earth, with extremely warm, humid conditions at high latitudes but little rain and subsurface water storage. Clouds increasingly obscure the surface as insolation increases, but visibility improves for modest increases in rotation period. Thus, moderately slowly rotating rocky planets with insolation near or somewhat greater than modern Earth's appear to be promising targets for surface characterization by a future direct imaging mission.

Del Genio, Anthony D.↗
NASA NTRS2019

Climates of Warm Earth-like Planets. III. Fractional Habitability from a Water Cycle Perspective

The habitable fraction of a planet's surface is important for the detectability of surface biosignatures. The extent and distribution of habitable areas are influenced by external parameters that control the planet's climate, atmospheric circulation, and hydrological cycle. We explore these issues using the ROCKE-3D general circulation model, focusing on terrestrial water fluxes and thus the potential for the existence of complex life on land. Habitability is examined as a function of insolation and planet rotation for an Earth-like world with zero obliquity and eccentricity orbiting the Sun. We assess fractional habitability using an aridity index that measures the net supply of water to the land. Earth-like planets become "superhabitable" (a larger habitable surface area than Earth) as insolation and day-length increase because their climates become more equable, reminiscent of past warm periods on Earth when complex life was abundant and widespread. The most slowly rotating, most highly irradiated planets, though, occupy a hydrological regime unlike any on Earth, with extremely warm, humid conditions at high latitudes but little rain and subsurface water storage. Clouds increasingly obscure the surface as insolation increases, but visibility improves for modest increases in rotation period. Thus, moderately slowly rotating rocky planets with insolation near or somewhat greater than modern Earth's appear to be promising targets for surface characterization by a future direct imaging mission.

Exoplanet atmospheric variability↗
NASA NTRS1967

Lunar Orbiter II - Photographic Mission Summary

Lunar Orbiter II photography of landing sites, and spacecraft systems performance. The second of five Lunar Orbiter spacecraft was successfully launched from Launch Complex 13 at the Air Force Eastern Test Range by an Atlas-Agena launch vehicle at 23:21 GMT on November 6, 1966. Tracking data from the Cape Kennedy and Grand Bahama tracking stations were used to control and guide the launch vehicle during Atlas powered flight. The Agena spacecraft combination was maneuvered into a 100-nautical-mile-altitude Earth orbit by the preset on-board Agena computer. In addition, the Agena computer determined the maneuver 1 and engine-bum period required to inject the spacecraft on the cislunar trajectory 20 minutes after launch. Tracking data from the downrange stations and the Johannesburg, South Africa station were used to monitor the entire boost trajectory.

LUNAR ORBITER↗
DOE OSTI2025

Unsteady Land-Sea Breeze Circulations in the Presence of a Synoptic Pressure Forcing

Unsteady land-sea breezes (LSBs) that result from time-varying surface temperature contrasts Δθ(t) are explored in the presence of a constant synoptic pressure forcing, M g , oriented from sea to land (α = 0°) or land to sea (α = 180°). Large eddy simulations reveal the development of four distinctive regimes, depending on the joint interaction between M g , α, and Δθ(t) in modulating the fine-scale dynamics. Time lags, computed as the shifts that maximize correlation coefficients of the velocity between the unsteady and the corresponding steady scenarios at Δθ = Δθ max , are found to be significant and to extend 2 hr longer for α = 0° compared to α = 180°. These diurnal dynamics result in nonequilibrium conditions that are significantly affected by the flow history, and that behave differently over the two patches for the different α’s. Turbulence is found to be out of equilibrium with the mean flow, and the mean itself is found to be out of equilibrium with the thermal forcing. The sea surface heat flux is consistently more sensitive than its land counterpart to the time-varying external forcing Δθ(t), and more so for synoptic forcing from land to sea (α = 180°). Hence, although the land reaches equilibrium faster, the sea patch is found to exert a stronger control on the turbulence-mean flow equilibrium response. Finally, the vertical velocity profile at the shore and shore-normal velocity transects at the first grid level are shown to encode the multiscale regimes of the LSBs evolution and can thus be used to identify these regimes using k-means clustering.

58 GEOSCIENCES↗
NASA NTRS2012

NASA's Robotic Lunar Lander Development Project

Since early 2005, NASA's Robotic Lunar Lander Development (RLLD) office at NASA MSFC, in partnership with the Applied Physics Laboratory (APL), has developed mission concepts and preformed risk-reduction activities to address planetary science and exploration objectives uniquely met with landed missions. The RLLD team developed several concepts for lunar human-exploration precursor missions to demonstrate precision landing and in-situ resource utilization, a multi-node lunar geophysical network mission, either as a stand-alone mission, or as part of the International Lunar Network (ILN), a Lunar Polar Volatiles Explorer and a Mercury lander mission for the Planetary Science decadal survey, and an asteroid rendezvous and landing mission for the Exploration Precursor Robotics Mission (xPRM) office. The RLLD team has conducted an extensive number of risk-reduction activities in areas common to all lander concepts, including thruster testing, propulsion thermal control demonstration, composite deck design and fabrication, and landing leg stability and vibration. In parallel, the team has developed two robotic lander testbeds providing closed-loop, autonomous hover and descent activities for integration and testing of flight-like components and algorithms. A compressed-air test article had its first flight in September 2009 and completed over 150 successful flights. This small test article (107 kg dry/146 kg wet) uses a central throttleable thruster to offset gravity, plus 3 descent thrusters (~37lbf ea) and 6 attitude-control thrusters (~12lbf ea) to emulate the flight system with pulsed operation over approximately 10s of flight time. The test article uses carbon composite honeycomb decks, custom avionics (COTS components assembled in-house), and custom flight and ground software. A larger (206 kg dry/322 kg wet), hydrogen peroxide-propelled vehicle began flight tests in spring 2011 and fly over 30 successful flights to a maximum altitude of 30m. The monoprop testbed also uses a central gravity-canceling thruster and 3 descent thrusters, but has 12 attitude-control thrusters and a maximum flight time of over a minute. The testbed uses aluminum ortho-grid decks, an LN200-1 IMU, Roke Manor Radar Altimeter, Illunis optical cameras, Novatel Pro-Pak GPS truth data system, Pressure transducers & thermocouples for housekeeping, "In-Control" ground system software, and the core Flight Executive (cFE) modular software environment. The peroxide lander testbed is able to accept other sensors and algorithms for testing, both from within NASA and from other customers. Through these activities, the RLLD team has significantly reduced technical risks for all small and medium class robotic landers for the Moon and other airless planetary bodies.

Cohen, Barbara A.↗
NASA NTRS2003

Novel Engineering and Fabrication Techniques Tested in Low-Noise- Research Fan Blades

A major source of fan noise in commercial turbofan engines is the interaction of the wake from the fan blades with the stationary vanes (stators) directly behind them. The Trailing Edge Blowing (TEB) project team at the NASA Glenn Research Center designed and fabricated new fan blades to study the effects of fan trailing edge blowing as a potential noise-reduction concept. The intent is to fill the rotor wake by supplying air to the rotor blade trailing edge at the proper conditions to minimize the wake deficit, and thus generate less noise. The TEB hardware is designed for the Active Noise Control Fan (ANCF) test rig in Glenn's Aeroacoustic Propulsion Laboratory. For this test, the air is fed from an external supply through the shaft of the rig. It is distributed to the base of each blade through an impeller, where it is forced into a plenum at the core of each blade. In actual engine configuration, air would most likely be bled from the compressor, but only at times when noise is an issue, such as takeoffs and landings. Glenn researchers designed and manufactured the blades in-house, using new techniques and concepts. The skins, which were designed for maximum strength in the directions of highest stress, were molded from multiple layers of carbon fiber. Considerable use was made of rapid prototyping techniques, such as laser sintering. The core was sintered from a lightweight polymer, and the retainer was CNC-machined (computer numerical control machined) from aluminum. All the components were joined with a cold-cure aerospace adhesive. These techniques and processes reduced the overall cost and allowed the new concept to be studied much sooner than would be possible using traditional fabrication methods. Since this test rig did not support the use of blade-monitoring techniques such as strain gauges, extensive bench testing was required to qualify the design. The blades were examined using a variety of methods including holography, pull tests (cyclic and failure), shake tests, rap tests, and nondestructive inspection. Acoustic testing of the ANCF fan using TEB has been ongoing since January of 2001. The fan has completed about 100 hr of testing with no structural, vibrational, or fatigue problems. Far-field acoustic measurements, in-duct mode measurements, precise hot wire surveys, and detailed performance measurements are providing data for evaluating the concept. The far-field noise data show that tone noise was reduced significantly with the initial ANCF TEB fan design. In addition, a significant reduction in unsteady stator loading has been measured, indicating the potential for stator broadband noise reduction. The acoustic benefits will be assessed and important design parameters identified to improve the ability to fully exploit any benefit provided by this technique. On the basis of the success of trailing edge blowing, Glenn plans to continue this research with a higher speed, higher pressure ratio fan operating in an acoustic wind tunnel to simulate flight conditions.

Cunningham, Cameron C.↗
NASA NTRS2021

Modeling Snow Ablation over the Western United States Mountains: Patterns and Controlling Factors

When compared with differences in snow accumulation predicted by widely used hydrological models, there is a much greater divergence among otherwise “good” models in their simulation of the snow ablation process. Here, we explore differences in the performance of the Variable Infiltration Capacity model (VIC), Noah land surface model with multiparameterization options (Noah-MP), the Catchment model, and the third-generation Simplified Simple Biosphere model (SiB3) in their ability to reproduce observed snow water equivalent (SWE) during the ablation season at 10 Snowpack Telemetry (SNOTEL) stations over 1992–2012. During the ablation period, net radiation generally has stronger correlations with observed melt rates than does air temperature. Average ablation rates tend to be higher (in both model predictions and observations) at stations with a large accumulation of SWE. The differences in the dates of last snow between models and observations range from several days to approximately a month (on average 5.1 days earlier than in observations). If the surface cover in the models is changed from observed vegetation to bare soil in all of the models, only the melt rate of the VIC model increases. The differences in responses of models to canopy removal are directly related to snowpack energy inputs, which are further affected by different algorithms for surface albedo and energy allocation across the models. We also find that the melt rates become higher in VIC and lower in Noah-MP if the shrub/grass present at the observation sites is switched to trees.

Snow↗
NASA NTRSDate not supplied

Characterization of Urban Air Mobility Vehicle Operational Noise and Community Noise Impact

This presentation focuses on the process for predicting urban air mobility (UAM) vehicle noise at the source and how that can be used to estimate the impact on the community. Following conceptual design, in which the vehicle is appropriately sized for its intended mission, a comprehensive analysis must be performed for a range of operating conditions spanning the flight envelope to determine the corresponding configurations of the vehicle, that is, the trimmed states. Many UAM vehicles have redundant controls, so the trimmed state for any particular operating condition may not be unique, with some states producing more noise than others. For each trimmed state, the noise produced by each source, for example, steady and unsteady rotor noise, inclusive of propulsion airframe aeroacoustic effects, may be computed and so-called source noise (hemi)spheres generated. Land use planning tools, including those using simulation and integrated modeling approaches, use these (or derived) data to generate noise exposure maps on the ground. Alternatively, these data may serve as input to auralization, turning the numerical data into an audible sound that can subsequently be used as part of a perception-influenced acoustic design process that takes into account human response.

urban air mobiliy↗
DOE OSTI2024

Climate, Hydrology, and Nutrients Control the Seasonality of Si Concentrations in Rivers

Abstract The seasonal behavior of fluvial dissolved silica (DSi) concentrations, termedDSi regime, mediates the timing of DSi delivery to downstream waters and thus governs river biogeochemical function and aquatic community condition. Previous work identified five distinct DSi regimes across rivers spanning the Northern Hemisphere, with many rivers exhibiting multiple DSi regimes over time. Several potential drivers of DSi regime behavior have been identified at small scales, including climate, land cover, and lithology, and yet the large‐scale spatiotemporal controls on DSi regimes have not been identified. We evaluate the role of environmental variables on the behavior of DSi regimes in nearly 200 rivers across the Northern Hemisphere using random forest models. Our models aim to elucidate the controls that give rise to (a) average DSi regime behavior, (b) interannual variability in DSi regime behavior (i.e., Annual DSi regime), and (c) controls on DSi regime shape (i.e., minimum and maximum DSi concentrations). Average DSi regime behavior across the period of record was classified accurately 59% of the time, whereas Annual DSi regime behavior was classified accurately 80% of the time. Climate and primary productivity variables were important in predicting Average DSi regime behavior, whereas climate and hydrologic variables were important in predicting Annual DSi regime behavior. Median nitrogen and phosphorus concentrations were important drivers of minimum and maximum DSi concentrations, indicating that these macronutrients may be important for seasonal DSi drawdown and rebound. Our findings demonstrate that fluctuations in climate, hydrology, and nutrient availability of rivers shape the temporal availability of fluvial DSi.

Environmental Sciences & Ecology↗
DOE OSTI2012

Thermal Controls on the Asian Summer Monsoon

The Asian summer monsoon affects more than sixty percent of the world's population; understanding its controlling factors is becoming increasingly important due to the expanding human influence on the environment and climate and the need to adapt to global climate change. Various mechanisms have been suggested; however, an overarching paradigm delineating the dominant factors for its generation and strength remains debated. Here we use observation data and numerical experiments to demonstrates that the Asian summer monsoon systems are controlled mainly by thermal forcing whereas large-scale orographically mechanical forcing is not essential: the South Asian monsoon south of 20°N by land–sea thermal contrast, its northern part by the thermal forcing of the Iranian Plateau and the East Asian monsoon and the eastern part of the South Asian monsoon by the thermal forcing of the Tibetan Plateau.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1973

Flight test results from the CV990 simulated space shuttle during unpowered automatic approaches and landings

Unpowered automatic approaches and landings with a CV990 aircraft were conducted to study navigation, guidance, and control problems associated with terminal area approach and landing for the space shuttle. The flight tests were designed to study from 11,300 m to touchdown the performance of a navigation and guidance concept which utilized blended radio/inertial navigation using VOR, DME, and ILS as the ground navigation aids. In excess of fifty automatic approaches and landings were conducted. Preliminary results indicate that this concept may provide sufficient accuracy to accomplish automatic landing of the shuttle orbiter without air-breathing engines on a conventional size runway.

Edwards, F. G.↗
NASA NTRS1973

Flight director design for a STOL aircraft.

The study described here was intended to explore some ways of giving the pilot the information necessary to perform as well as an autopilot. A fixed-base flight simulator was built to study pilot/director/aircraft performance. Instrument rated pilots used the different director-displays in an approach down to touchdown, including a flare and decrab maneuver. Two well established areas of control theory are combined in the design of the cockpit display. Optimal control theory and the theory of manual control are used to find the feedback gains required to drive the display symbols. Conclusions based on the simulator are presented. The results show that the director display developed in the work provides more than adequate information for simulated landing in highly turbulent conditions.

Seitz, W. R.↗
NASA NTRS1973

Study of control system effectiveness in alleviating vortex wake upsets.

The problem of an airplane being upset by encountering the vortex wake of a large transport on takeoff or landing is currently receiving considerable attention. This paper describes the technique and results of a study to assess the effectiveness of automatic control systems in alleviating vortex wake upsets. A six-degree-of-freedom nonlinear digital simulation was used for this purpose. The analysis included establishing the disturbance input due to penetrating a vortex wake from an arbitrary position and angle. Simulations were computed for both a general aviation airplane and a commercial jet transport. Dynamic responses were obtained for the penetrating aircraft with no augmentation and with various command augmentation systems. The results of this preliminary study indicate that it is feasible to use an automatic control system to alleviate vortex encounter upsets.

Johnson, W. A.↗
NASA NTRS1974

Analysis of vortex wake encounter upsets

The problem of an airplane being upset by encountering the vortex wake of a large transport on takeoff or landing is currently receiving considerable attention. This report describes the technique and results of a study to assess the effectiveness of automatic control systems in alleviating vortex wake upsets. A six-degree-of-freedom nonlinear digital simulation was used for this purpose. The analysis included establishing the disturbance input due to penetrating a vortex wake from an arbitrary position and angle. Simulations were computed for both a general aviation airplane and a commercial jet transport. Dynamic responses were obtained for the penetrating aircraft with no augmentation, and with various command augmentation systems, as well as with human pilot control. The results of this preliminary study indicate that attitude command augmentation systems can provide significant alleviation of vortex wake upsets; and can do it better than a human pilot.

Johnson, W. A.↗
NASA NTRS1979

Mapping of sea ice and measurement of its drift using aircraft synthetic aperture radar images

Side-looking radar images of Arctic sea ice were obtained as part of the Arctic Ice Dynamics Joint Experiment. Repetitive coverages of a test site in the Arctic were used to measure sea ice drift, employing single images and blocks of overlapping radar image strips; the images were used in conjunction with data from the aircraft inertial navigation and altimeter. Also, independently measured, accurate positions of a number of ground control points were available. Initial tests of the method were carried out with repeated coverages of a land area on the Alaska coast (Prudhoe). Absolute accuracies achieved were essentially limited by the accuracy of the inertial navigation data. Errors of drift measurements were found to be about + or - 2.5 km. Relative accuracy is higher; its limits are set by the radar image geometry and the definition of identical features in sequential images. The drift of adjacent ice features with respect to one another could be determined with errors of less than + or - 0.2 km.

Leberl, F.↗
NASA NTRS1979

Accelerated development and flight evaluation of active controls concepts for subsonic transport aircraft. Volume 2: AFT C.G. simulation and analysis

Relaxed static stability and stability augmentation with active controls were investigated for subsonic transport aircraft. Analytical and simulator evaluations were done using a contemporary wide body transport as a baseline. Criteria for augmentation system performance and unaugmented flying qualities were evaluated. Augmentation control laws were defined based on selected frequency response and time history criteria. Flying qualities evaluations were conducted by pilots using a moving base simulator with a transport cab. Static margin and air turbulence intensity were varied in test with and without augmentation. Suitability of a simple pitch control law was verified at neutral static margin in cruise and landing flight tasks. Neutral stability was found to be marginally acceptable in heavy turbulence in both cruise and landing conditions.

Urie, D. M.↗