Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GaGe”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Resizing procedure for structures under combined mechanical and thermal loading

The fully-stressed design (FSD) appears to be the most widely used approach for sizing of flight structures under strength and minimum-gage constraints. Almost all of the experience with FSD has been with structures primarily under mechanical loading as opposed to thermal loading. In this method the structural sizes are iterated with the step size, depending on the ratio of the total stress to the allowable stress. In this paper, the thermal fully-stressed design (TFSD) procedure developed for problems involving substantial thermal stress is extended to biaxial stress members using a Von Mises failure criterion. The TFSD resizing procedure for uniaxial stress is restated and the new procedure for biaxial stress members is developed. Results are presented for an application of the two procedures to size a simplified wing structure.

Adelman, H. M.↗
NASA NTRS1976

Effect of laminate construction on residual stresses in composites

The effects of ply stacking sequence and ply orientation on the magnitude of lamination residual stresses in graphite/polyimide angle-ply laminates was studied. Embedded strain gage techniques were used to measure thermal strains in laminates of different layup, and residual strains were determined by comparing thermal strains in the angle-ply laminates with those of a unidirectional laminate. The ply stacking sequence did not have an effect on the magnitude of residual strains.

Daniel, I. M.↗
NASA NTRS1976

Attenuation of propagation through rain for an earth-satellite path correlated with predicted values using radar

During the summer of 1974 and spring of 1975, measurements of attenuation of propagation through rain were made at Wallops Island, VA, using 13 and 18 GHz transmitters operating in the uplink mode toward the ATS-6 satellite. Simultaneously, rain reflectivity levels were measured along the earth-satellite path using a high resolution (0.4 deg beamwidth) S-band radar having a scanning antenna. Four rain-gages and two disdrometers were also located in the vicinity of the transmitters. The radar and disdrometer data were used in a modelling program to predict attenuation levels which were subsequently compared to the directly measured fades over nearly simultaneous time intervals. Predicted attenuation levels were obtained for three drop size distributions. Comparisons between predicted and measured attenuation levels showed the APL dropsize distribution gave the smallest rms difference of 1.3 dB at 13 and 18 GHz although the rms difference corresponding to Marshall-Palmer was close to this value. The good agreement suggests the validity of using radar to model path attenuation to obtain attenuation statistics.

Goldhirsh, J.↗
NASA NTRS1977

A CW ultrasonic bolt-strain monitor

There exists a need for a relatively inexpensive system for measuring strain in bolts. The torque wrench is one technique for straining bolts which has been widely applied. Unfortunately, friction in the bolt threads and between the nut and the work tend to make such a simple system inaccurate. In practice, a torque wrench is unacceptable for many situations where strain is critical. In this article, an ultrasonic technique is described which can indicate changes in bolt strain to better than one part in 10,000. The technique is based on the one-dimensional propagating-ultrasonic-wave model and uses a new ultrasonic instrument called a Reflection Oscillator Ultrasonic Spectrometer which is a closed-loop feedback marginal-oscillator system that frequency locks the device to the peak of a mechanical resonance in the bolt. The instrument indicates a shift in the bolt resonance frequency due to elongation and changes in velocity of sound due to strain. Data are presented comparing a standard torque wrench to the ultrasonic monitor for different measured stresses on the bolt as well as for different bolt conditions. The strain instrument can be used to monitor changing stresses, to measure material properties and may be applied as a strain gage or load cell.

Heyman, J. S.↗
NASA NTRS1977

Form drag, skin friction, and vortex shedding frequencies for subsonic and transonic crossflows on circular cylinder

A series of wind-tunnel tests covering a range of Mach numbers and Reynolds numbers in subsonic and transonic flows was conducted on a circular cylinder placed normal to the flow. Form drag coefficients were determined from surface-pressure measurements and displayed as a function of Mach number to show the drag rise phenomenon. Buried wire gages arranged on the model surface were used to measure skin-friction distributions and vortex-shedding frequencies at different flow conditions. It was found that detectable periodic shedding ceases above M = 0.9. The measured skin-friction distributions indicate the positions of mean separation points clearly; these values are documented for the different flow conditions.

Murthy, V. S.↗
NASA NTRS1976

Plane-stress fracture of compact and notch-bend specimens

Thin-gaged or high toughness materials containing cracks usually fail in a ductile manner with nominal failure stresses approaching the ultimate strength of the material. For such materials, a two-parameter fracture criterion was developed. An equation which related the linear elastic stress-intensity factor, elastic nominal stress, and two material parameters has previously been derived and has been used as a fracture criterion for surface- and through-cracked specimens under tensile loading. In the present paper the two-parameter fracture criterion was rederived in a more general form and was extended to compact and notch-bend fracture specimens. A close correlation was found between experimental and calculated failure stresses.

Newman, J. C., Jr.↗
NASA NTRS1977

10-deg off-axis test for shear properties in fiber composites

A combined theoretical and experimental investigation was conducted to assess the suitability of the 10-deg off-axis tensile test specimen for the intralaminar shear characterization of unidirectional composites. Composite mechanics, a combined-stress failure criterion, and a finite-element analysis were used to determine theoretically the stress-strain variation across the specimen width and the relative stress and strain magnitudes at the 10-deg plane. Strain gages were employed to measure the strain variation across the specimen width at specimen midlength and near the end tabs. Specimens from Mod-I/epoxy, T-300/epoxy, and S-glass/epoxy were used in the experimental program. It was found that the 10-deg off-axis tensile test specimen is suitable for intralaminar shear characterization, and it is recommended that it should be considered as a possible standard test specimen for such a characterization.

Chamis, C. C.↗
NASA NTRS1977

A study of fatigue crack closure using electric potential and compliance techniques

The objective of this study was to compare closure data obtained on the same specimen with crack tip compliance gage and electric potential techniques. Equivalent results on closure using the two techniques were obtained on 7075-T651 aluminum center cracked panels. The results also indicated that closure was a function of stress ratio, specimen thickness and maximum applied stress intensity. Maximum stress intensity had a particularly strong effect on closure in the range of applied stresses used. This observed dependence of closure on specimen thickness and maximum stress intensity should account for many of the discrepancies in closure behavior found in the literature. Observations on potential system behavior during closure measurements are also reported.

Clarke, C. K.↗
NASA NTRS1977

Compliance calibration of specimens used in the R-curve practice

The compliance calibrations for the compact (CS) and crack-line-wedge-loaded (CLWL) specimens have been determined by experimental measurements and by boundary-collocation analysis. The CS and CLWL specimen configurations were modeled more accurately than those used in previous analytical investigations. Polynomial expressions for the compliance at various stations along the crack line for CS and CLWL specimens are presented. The compliance calibrations for the center-crack tension (CCT) specimen have been determined theoretically by boundary-collocation and finite-element analysis. The calculated compliance values for the CCT specimen are compared with values obtained from the Irwin-Westergaard expression and from a modification to the Irwin-Westergaard expression proposed by Eftis and Liebowitz. The Eftis-Liebowitz expression was found to be in good agreement (plus or minus 2 percent) with both analyses for crack aspect ratios up to 0.8 and for gage half-span to specimen width ratios up to 0.5.

Mccabe, D. E.↗
NASA NTRS1979

Coal mining with a liquid solvent

Study suggests carbonated water can dissolve or suspend coal and carry it to surface. Mixture of carbon dioxide and water may be coal solvent that will make unmanned mining reality. When used with proposed process monitoring coal solubility with conventional strain gage, solvent is basis for rapid cost effective extraction of coal from underground seams.

Lawson, D. D.↗
NASA NTRS1977

Development and application of operational techniques for the inventory and monitoring of resources and uses for the Texas coastal zone. Volume 1: Text

The author has identified the following significant results. Image interpretation and computer-assisted techniques were developed to analyze LANDSAT scenes in support of resource inventory and monitoring requirements for the Texas coastal region. Land cover and land use maps, at a scale of 1:125,000 for the image interpretation product and 1:24,000 for the computer-assisted product, were generated covering four Texas coastal test sites. Classification schemes which parallel national systems were developed for each procedure, including 23 classes for image interpretation technique and 13 classes for the computer-assisted technique. Results indicate that LANDSAT-derived land cover and land use maps can be successfully applied to a variety of planning and management activities on the Texas coast. Computer-derived land/water maps can be used with tide gage data to assess shoreline boundaries for management purposes.

Harwood, P.↗
NASA NTRS1977

Application of remotely sensed land-use information to improve estimates of streamflow characteristics, volume 8

The author has identified the following significant results. Land use data derived from high altitude photography and satellite imagery were studied for 49 basins in Delaware, and eastern Maryland and Virginia. Applying multiple regression techniques to a network of gaging stations monitoring runoff from 39 of the basins, demonstrated that land use data from high altitude photography provided an effective means of significantly improving estimates of stream flow. Forty stream flow characteristic equations for incorporating remotely sensed land use information, were compared with a control set of equations using map derived land cover. Significant improvement was detected in six equations where level 1 data was added and in five equations where level 2 information was utilized. Only four equations were improved significantly using land use data derived from LANDSAT imagery. Significant losses in accuracy due to the use of remotely sensed land use information were detected only in estimates of flood peaks. Losses in accuracy for flood peaks were probably due to land cover changes associated with temporal differences among the primary land use data sources.

Pluhowski, E. J.↗
NASA NTRS1976

Wind-tunnel investigation of aerodynamic performance, steady amd vibratory loads, surface temperatures, and acoustic characteristics of a large-scale twin-engine upper-surface blown jet-flap configuration

Static and wind-on tests were conducted to determine the aerodynamic characteristics of and the effects of jet impingement on the wing of a large scale upper surface blown configuration powered with an actual turbine engine. The wing and flaps were instrumented with experimental dual-sensing transducer units consisting of a fluctuating pressure gage, a vibratory accelerometer, and a surface mounted alumel thermocouple. Noise directivity and spectral content measurements were obtained for various flap configurations and various engine thrust settings to provide baseline noise data for other upper surface blown configurations.

Source record↗
NASA NTRS1977

Synthesis of blade flutter vibratory patterns using stationary transducers

Flutter frequency was determined and rotor vibratory amplitude and phase distributions during flutter were reconstructed from stationary aerodynamic type measurements. A previously reported optical method for measuring blade-tip displacement during flutter was extended by means of digital analysis. Displacement amplitudes and phase angles were determined based on this method. For selected blades, spectral results were also obtained from strain gage measurements. The results from these three types of measurement were compared and critically evaluated.

Kurkov, A.↗
NASA NTRS1977

An analysis of the rotor blade stresses of the three stage compressor of the Ames Research Center 11- by 11-foot transonic wind tunnel

The static and dynamic rotor blade stresses of the three stage compressor were measured. Data are presented in terms of total blade stress for the complete operational range of compressor speeds and tunnel total pressures. Modal frequencies and variations with tunnel conditions were measured. Phase angles and coherences between various gage combinations are also presented. Recommendations for improvements are given for future rotor blade experimental investigations.

Dods, J. B., Jr.↗
NASA NTRS1978

Residual stresses in angleplied laminates and their effects on laminate behavior

Evidence of the presence of lamination residual stresses in angleplied laminates were transply cracks and warpage of unsymmetric laminates which occur prior to application of any mechanical load. Lamination residual strains were measured using the embedded strain gage technique. These strains result from the temperature differences between cure and room temperature and vary linearly within this temperature range. Lamination residual stresses were usually present in angleplied fiber composites laminates; they were also present in unidirectional hybrids and superhybrids. For specific applications, the magnitudes of lamination residual stresses were determined and evaluated relative to the anticipated applied stresses. Particular attention was given to cyclic thermal loadings in applications where the thermal cycling takes place over a wide temperature range.

Chamis, C. C.↗
NASA NTRS1978

Indoor test for thermal performance evaluation of the Solaron (air) solar collector

The test procedure used and the results obtained from an evaluation test program, conducted to obtain thermal performance data on a Solaron double glazed air solar collector under simulated conditions in a solar simulator are described. A time constant test and incident angle modifier test were also conducted to determine the transient effect and the incident angle effect on the collector. These results and the results of the collector load test are also discussed. The Solaron collector absorber plate is made of 24-gage steel, the coating is baked-on black paint, the cover consists of two sheets of 1/8-inch low-iron tempered glass, and the insulation is one thickness of 3 5/8-inch fiberglass batting.

Source record↗