Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Electron Diffraction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Spatially resolved phase transformation mapping in 410 stainless steel during additive manufacturing visualized via real-time infrared data

Here, in this study, we demonstrate that spatially resolved cooling curves derived from real-time infrared (IR) thermography during additive manufacturing (AM) can capture spatial variations in phase transformation temperatures through cooling curve analysis (CCA). Using this approach, we show that during laser hot-wire deposition of 410 stainless steel (410SS), the martensite start temperature (M s ) evolves dynamically throughout the build. The M s temperature is spatially nonuniform, ranging from 185 °C to 348 °C, with the lowest values toward the build center and higher values toward the upper region of the deposit. In the lower portion of the build, no M s inflection is detected via CCA, consistent with transformation occurring earlier during thermal cycling followed by tempering during subsequent thermal cycles. These trends in M s are corroborated by characterizing the microstructure by electron backscatter diffraction (EBSD). Traditionally, M s is assumed to be constant, and a single interpass temperature is applied during both deposition and residual stress modeling. Our results demonstrate that IR-derived cooling curves provide a route to spatially and temporally resolved transformation temperature tracking for dynamic interpass control and improved residual-stress modeling.

Additive manufacturing↗
DOE OSTI2026

Texture development in magnetostrictive Fe-Ga alloys processed by laser powder bed fusion

Iron-gallium (Fe-Ga, Galfenol) alloys are promising magnetostrictive materials for actuators, sensors, and energy harvesting, but their performance is highly sensitive to microstructure and texture. Additive manufacturing by laser powder bed fusion (LPBF) offers a pathway to engineer texture and integrate functional materials into complex geometries. Here, we fabricate Fe-Ga alloys (Fe 82.2 Ga 17.8 ) by LPBF of gas-atomized powders and systematically optimize laser power and scan speed to maximize density and control texture. Nearly full-density parts (up to 99.6 %) are achieved within a narrow processing window. Electron backscatter diffraction (EBSD) reveals a strong <100> fiber texture aligned with the build direction and columnar grains up to 1 mm long. Magnetostriction measurements show saturation magnetostriction of 190 ppm in the build direction. Correlating texture data with macroscopic magnetostriction, we estimate intrinsic magnetostriction constants (λ 100 = 228 ppm, λ 111 = 12 ppm), closely matching single crystal-derived values. These results demonstrate the critical interplay between processing, texture, and functional performance in additively manufactured Fe-Ga alloys and establish LPBF as a viable route for high-performance magnetostrictive materials.

Additive manufacturing↗
DOE OSTI2023

Surface grain refinement of casting A380 aluminum alloy by ultrasonic-assisted surface mechanical grinding treatment

A novel surface processing technique, ultrasonic-assisted surface mechnical grinding treatment (U-SMGT), was proposed and applied to modify the surface micriostructure of the casting aluminum alloy (A380). Comprehensive post-process chracterization techniques including 3D profilometry, optical microscope, scanning electric microscopy (SEM), and electron backscatter diffraction (EBSD) were carried out to investigate the surface morphology and microstructure of the processed region (PR). It was found that a surface layer of grain refinement with a thickness of about 50 µm was formed. In the as-received base material (BM), large clusters of dendritic eutectic phase with a size of approximately 20 µm were isolated by α-Al matrix. Nano-indentation tests showed that hardness of the eutectic and α-Al in the as-received BM was 2.15 GPa and 1.2 GPa respectively. After U-SMGT, the large dendritic eutectic phase was broken down into much fine particles with an average size of 0.57 µm. These fine particles were uniformly distributed into the α-Al matrix. Nano-indentation measurement exhibited a hardness of 2.27 GPa within the processed region. The overall high hardness in the processed region is a result of the pinning effect of uniformly distributed fine dendrites and grain refinement of Al-matrix.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Fatigue life prediction of powder bed fused–laser beam AlSi10Mg: Incorporating critical defects via crystal plasticity modelling

The current study provides a microstructurally-based computational framework to predict the fatigue life of additive manufactured (AM), i.e., powder bed fused–laser beam (PBF-LB), AlSi10Mg specimens using the crystal plasticity finite element method (CPFEM). The fractography analysis, electron backscatter diffraction (EBSD), uniaxial and cyclic responses, and fatigue life of specimens were used to inform the computational framework. CPFE simulation was used to compute fatigue indicator parameters (FIPs) as fatigue driving forces. A new fatigue criterion is introduced based on FIPs, which was calibrated using experimental fatigue data. The proposed fatigue measure was evaluated versus the specimens with critical defects of various sizes and locations subjected to different stress amplitudes. The results show that the developed framework can capture the fatigue life of samples with different critical defect locations and sizes along with different stress amplitudes for both high-cycle fatigue (HCF) and very high-cycle fatigue (VHCF) regimes.

Additive manufacturing↗
DOE OSTI2022

A practical guide to characterizing irradiated nuclear fuels using FIB tomography

We report focused ion beam (FIB) tomography with combined electron backscatter diffraction (EBSD) and energy dispersive x-ray spectroscopy (EDS) is a technique capable of statistically characterizing the microstructure and spatial compositional variation of nuclear fuel in three-dimensions (3D). The 3D visualization from FIB tomography provides a comprehensive picture of the interconnected microstructural and compositional features that can impact fuel performance. While these features are often characterized with surface examination, the complexity and relationship of fission products and grain boundary networks may not fully be captured by these 2D methods. This work presents a practical guide to FIB tomography that is tailored to nuclear fuel characterization. The steps used to collect and process the data are provided along with the scripts used to process the data. Additionally, suggestions for future characterization efforts utilizing this approach are given.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Effect of subfreezing testing temperature on tensile mechanical behavior of fine-grained magnesium

Here, the effect of testing temperature on mechanical properties and deformation mechanisms was investigated by tensile testing of fine-grained magnesium samples under a range of temperatures (i.e. room temperature 20°C, subfreezing temperatures 0°C, -30°C, and - 60°C) and microstructural observations of both untested and tested samples using electron backscatter diffraction. The results suggest that mechanical properties and deformation mechanisms were significantly affected by lowering testing temperature. Strength increased linearly and ductility decreased linearly with the decrease of testing temperature. Although twinning is generally known to be athermal, this experimental study shows that tensile twinning is the dominating deformation mechanism at room temperature, and that twinning is negligible and dislocation operation is the primary deformation mechanism at 0°C, -30°C, and -60°C

36 MATERIALS SCIENCE↗
DOE OSTI2021

Prediction of softening kinetics and recrystallization texture in non-isothermally annealed bulged tubes using CPFEM and CA models

A hierarchically coupled cellular automata (CA) model, crystal plasticity finite element method (CPFEM), and thermal finite element (FE) model is developed to predict the softening kinetics of the bulged steel tube during non-isothermal annealing. Through the developed model, the kinetics of softening mechanisms including static recovery (SRV) and static recrystallization (SRX), as well as the recrystallization texture are predicted. Later, the Johnson-Mehl-Avrami-Kohnogorov (JMAK) model based on the predicted SRX data is developed to interpret the recrystallization behavior of the material. To perform this study, diverse experimental tests including tube hydroforming (THF), annealing, uniaxial tensile test, hardness test, as well as microstructure observations through optical microscopy and Electron Backscatter Diffraction (EBSD) tests on steel tube are performed. The obtained experimental data are utilized to calibrate and verify the implemented CPFEM model for simulation of THF process, thermal FE model for prediction of the local temperature over annealing time, and CA algorithm for modeling of the softening kinetics and texture evolution throughout the annealing process. The study shows that the predicted deformation characteristics, softening kinetics, recrystallization texture and temperature profile during non-isothermal annealing are in good agreement with experimental data. During the annealing process, a total of four stages for the kinetics of softening mechanisms is observed: No softening; SRV only; SRV dominant; and SRX dominant. During the progress of SRX, the behavior of recrystallization is abruptly changed, confirming that two different mechanisms are controlling the kinetics of transformation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Investigation of deformation mechanisms in an advanced FeCrAl alloy using in-situ SEM-EBSD testing

The deformation mechanisms associated with uniaxial tensile testing are observed by conducting tensile experiments of an FeCrAl alloy using scanning electron microscopy (SEM) coupled with electron backscattered diffraction (EBSD). Prior to the deformation, investigated alloy was consisting grain and precipitate size of ~63.0 μm and ~6.7 μm, respectively. The recorded SEM micrographs and EBSD data at increasing levels of strains revealed the complex phenomena of slip bands’ formation in the presence of surface grain morphology evolution and their (001), (110) and (111) crystallographic planes distortions. The grains with orientation (110)||tensile direction (TD) shows higher shape change; however, (001)||TD and (111)||TD oriented grains show higher lattice gradient formation. Extracted information from the EBSD indicates that the crystallographic rotations drive towards specific, fiber-like texture in relation to the loading direction. Postmortem analysis of the recorded microstructure during the tensile deformation explains the phenomena of crack formation in the hard-intermetallic particles before the ultimate tensile strength (UTS). However, after the UTS, pores were identified in the neck that resulted from extensive plastic deformation. In-depth analysis was carried out to identify the cause of cracks and pores formation phenomena during the tensile test.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Correlating dislocation structures to basal and prismatic slip bands near grain boundaries in tensile-tested Mg–4Al using a multiscale electron microscopy approach

Dislocation structures where basal and prismatic slip bands meet grain boundaries in tensile-tested Mg with 4 wt% Al (Mg–4Al) were studied using a multiscale electron microscopy approach to explore the assumptions made for the dislocation pileup theory: a) slip bands consist of dislocation arrays piling up near grain boundaries, and b) stress concentration in the adjacent grain is solely caused by dislocation pileup. After post-testing electron backscatter diffraction (EBSD) scans, focused-ion-beam (FIB) lift-out specimens were prepared from regions of interest so that the specimen plane is parallel to the bulk sample surface to allow for direct correlation between mesoscale and microscale characterization. High dislocation density and the dislocation arrays in the slip bands corroborated with the first assumption. Evidence of plastic deformation in all grains, however, showed that the second assumption was false. Additionally, dislocation structures including crystal rotation boundaries and dislocations dissociating to the basal plane provide additional stress relief mechanisms near grain boundaries that are not accounted for in many crystal plasticity models, which requires auxiliary models to more accurately predict the stress and strain distribution in a microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Spall damage mechanisms in laser powder bed fabricated stainless steel 316L

This paper reports on spall damage mechanisms in laser powder bed fusion (LPBF) fabricated stainless steel 316L (SS316L) subjected to uniaxial, strain plate-impact loading and explores failure evolution with increasing impact velocity and peak pressure. Analysis of velocimetry profiles reveals a heterogeneous failure response with several different failure mechanisms activated during impact and resulting spall. The analysis is supported by optical microscopy and electron backscattered diffraction (EBSD) observation of soft recovered impacted samples, which show evidence of localized nano-twinning, twin growth, severe grain rotation, and grain refinement along the spall plane, in addition to pore nucleation, coalescence, and growth. Furthermore, the observed failure mechanisms, including crack formation and propagation along high angle grain boundaries (HAGBs), are not consistently indicative of ductile fracture typical of wrought stainless steel.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Quasi-static and dynamic response of a Cu/Nb composite following equal channel angular extrusion

The article presents a study of the plastic properties of a Cu–18%Nb composite following equal channel angular extrusion under both low- and high-strain rate loadings. The microstructures are characterized by optical and scanning electron microscopy as well as electron backscatter diffraction. Comparisons are also made with a Cu–50%Nb laminate made by accumulative roll bonding. Textures obtained within the respective phases in the extruded composite closely mimic those previously reported for the pure components alone (Cu, Nb). Grain sizes of the major phase (Cu) exhibit broad distributions, due largely to partial recrystallization during the extrusion process. Further re-crystallization is obtained within localized deformation bands produced at high strain rates (3 × 10 3 s –1 ). While the degree of anisotropy and the strain rate sensitivity of the composite response are similar to those of pure Cu after extrusion, the strength levels of the composite are somewhat greater, falling broadly between those obtained in the pure components after extrusion to comparable plastic strains. Furthermore, the implications for selection of composite composition and processing for achieving higher strengths are briefly discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Analysis of orientation-dependent deformation mechanisms in additively manufactured Zr using in-situ micromechanical testing: Twinning and orientation gradient

Here, orientation-dependent plasticity in zirconium (Zr)-alloy, which is produced through ultrasonic additive manufacturing (UAM) with subsequent hot-isostatic pressing (HIP), was analyzed by recording electron backscattered diffraction (EBSD) data during in-situ micromechanical testing. Three (0001) plane orientations of a hexagonal close-packed (HCP) structure were analyzed parallel to (1) the rolling direction [X||tensile direction (TD)], (2) the build direction [Z], and (3) the transverse direction [Y]. The analysis revealed that the grains with ~<0001>||TD show twin-dominant plasticity with three variants from {10 $\overline{1}$ 2}<$\overline{1}$ 011>; minor slipping with ($10\overline{1}$ 1)[$\overline{2}$ 113], and ($11\overline{2}$ 2)[$\overline{1} \overline{1}$ 23] pyramidal slip has also been observed. However, grains with orientation ~<0001>⊥TD are mainly sensitive to dislocations assisted plasticity-leading to orientation gradients formation. Furthermore, the neck formation was identified as originating from higher populated micro-crack locations and their association with localized plasticity at defect points in the UAM material. These results demonstrate that minimization of impurities to enable grain growth across prior foil interfaces makes HIP an effective methodology for producing Zr plate, with deformation characteristics expected for conventionally manufactured Zr.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Evolution of microstructure and strength of a high entropy alloy undergoing the strain-induced martensitic transformation

In a recent work, we have reported outstanding strength and work hardening exhibited by a metastable high entropy alloy (HEA), Fe 42 Mn 28 Co 10 Cr 15 Si 5 (in at. %), undergoing the strain-induced martensitic transformation from metastable gamma austenite (γ) to stable epsilon martensite (ε). However, the alloy exhibited poor ductility, which was attributed to the presence of the brittle sigma (σ) phase in its microstructure. The present work reports the evolution of microstructure, strength, and ductility of a similar HEA, Fe 38.5 Mn 20 Co 20 Cr 15 Si 5 Cu 1.5 (in at. %), designed to suppress the formation of σ phase. A cast and then rolled plate of the alloy was processed into four conditions by annealing for 10 and 30 min at 1100 °C and by friction stir processing (FSP) at tool rotation rates of 150 and 400 revolutions per minute (RPM) to facilitate detailed examinations of variable initial grain structures. Neutron diffraction and electron microscopy were employed to characterize the microstructure and texture evolution. The initial materials had variable grain size but nearly 100% γ structure. Diffusionless strain induced γ→ε phase transformation took place under compression with higher rate initially and slower rate at the later stages of deformation, independent on the initial grain size. The transformation facilitated part of plastic strain accommodation and rapid strain hardening owing to a transformation-induced dynamic Hall-Petch-type barrier effect, increase in dislocation density, and texture. Here, the peak strength of nearly 2 GPa was achieved under compression using the structure created by double pass FSP (150 RPM followed by 150 RPM). Remarkably, the tensile elongation exhibited by the alloy was nearly 20% with fracture surfaces featuring a combination of ductile dimples and cleavage.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Directed energy deposition of Haynes 282 nickel superalloy

Laser powder directed energy deposition was employed to fabricate Haynes® 282 Ni-based superalloy for high temperature creep testing. Material was heat treated using a single-step aging heat treatment of 800 °C for 4 h. Microstructural analysis was conducted in the as-deposited, solution-annealed, and age-hardened conditions. γ′ precipitates were absent in the as-deposited and annealed condition but formed during aging with an average size of 48.5 ± 12 nm. γ’ denuded zones ranging in thickness from 73 to 469 nm were observed adjacent to an effectively continuous grain boundary carbide film that covered 72.5% of the measured boundary length. The heat-treated material contained a high-volume fraction of TiC carbides ranging in size from 38 to 457 nm. Electron backscatter diffraction showed partial recrystallization, with 77-83% recrystallized area and a heterogeneous grain-size distribution. Creep testing at 750 °C at 300, 320, and 350 MPa revealed significantly inferior performance compared to wrought material, with higher strain rates, earlier tertiary onset, and shorter rupture lives. Fractography shows that failure was dominated by intergranular rupture. Post rupture microstructural analysis results suggest that the creep behavior was primarily governed by the non-equilibrium interface network rather than the bulk γ/γ’ matrix. In conclusion, the findings indicate that achieving wrought-like creep performance necessitates substantial improvements in the additive process, specifically focusing on enhanced homogenization, full recrystallization, and precise control over the morphology and distribution of carbides.

36 - MATERIALS SCIENCE↗
DOE OSTI2022

Numerical and experimental characterization of twin transmission across grain boundaries along the forward and lateral directions

Pervasive deformation twinning and transmission events across grain boundaries (GBs) affect the strength and failure of hexagonal close-packed (HCP) magnesium. A three-dimensional twin can transmit along the twinning shear direction, (forward), and along the direction perpendicular to both the twinning plane normal and the shear direction, (lateral). For the first time, phase-field calculations and electron backscatter diffraction (EBSD)-based statistical analysis are combined to investigate the effect of the twinned grain boundary characteristics on twin transmission (TT) along the forward and lateral directions. This combined analysis reveals that TT propensity decreases with increasing misorientation angle across the GB for both forward and lateral directions. Also, the TT is more favorable along the lateral than along the forward direction. Twin transmission seems harder across GBs with a misorientation axis closer to the twin -direction than the other directions ( and ). Further, the PF calculations reveal that, at the onset of a transmission process, the crystallography tends to be preserved in the case of lateral transmission, whereas, in the forward transmission case, the transmitted twin punches straight through the GBs and its morphology prevails. Additionally, the EBSD analysis finds that pure forward and lateral transmissions do not occur often, yet reveals a preference for lateral propagation consistent with PF simulations. Further, the local twin transmission configurations observed in the actual material do not correspond to pure tilt or twist GBs, which are most commonly considered as model cases.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Solidification and crystallographic texture modeling of laser powder bed fusion Ti-6Al-4V using finite difference-monte carlo method

Laser powder bed fusion (LPBF) additive manufacturing makes near-net-shaped parts with reduced material cost and time, rising as a promising technology to fabricate Ti-6Al-4V, a widely used titanium alloy in aerospace and medical industries. However, LPBF Ti-6Al-4V parts produced with 67° rotation between layers, a scan strategy commonly used to reduce microstructure and property inhomogeneity, have varying grain morphologies and weak crystallographic textures that change depending on processing parameters. Here, this study predicts LPBF Ti-6Al-4V solidification at three energy levels using a finite difference-Monte Carlo method and validates the simulations with large-area electron backscatter diffraction (EBSD) scans. The developed model accurately shows that a <001> texture forms at low energy and a <111> texture occurs at higher energies parallel to the build direction but with a lower strength than the textures observed from EBSD. A validated and well-established method of combining spatial correlation and general spherical harmonics representation of texture is developed to calculate a difference score between simulations and experiments. The quantitative comparison enables effective fine-tuning of nucleation density (N 0 ) input, which shows a nonlinear relationship with increasing energy level. Future improvements in texture prediction code and a more comprehensive study of N 0 with different energy levels will further advance the optimization of LPBF Ti-6Al-4V components. These developments contribute a novel understanding of crystallographic texture formation in LPBF Ti-6Al-4V, the development of robust model validation and calibration pipeline methodologies, and provide a platform for mechanical property prediction and process parameter optimization.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Detector requirements and simulation results for the EIC exclusive, diffractive and tagging physics program using the ECCE detector concept

This article presents a collection of simulation studies using the ECCE detector concept in the context of the EIC’s exclusive, diffractive, and tagging physics program, which aims to further explore the rich quark–gluon structure of nucleons and nuclei. To successfully execute the program, ECCE proposed to utilize the detector system close to the beamline to ensure exclusivity and tag ion beam/fragments for a particular reaction of interest. Preliminary studies confirm the proposed technology and design satisfy the requirements. Further, the projected physics impact results are based on the projected detector performance from the simulation at 10 or 100 fb -1 of integrated luminosity. Additionally, insights related to a potential second EIC detector are documented, which could serve as a guidepost for future development.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

Photoacoustic 3-D imaging of polycrystalline microstructure improved with transverse acoustic waves

Non-invasive fast imaging of grain microstructure of polycrystalline ceria with sub-micrometric spatial resolution is performed via time-domain Brillouin scattering. The propagation of a nanoacoustic pulse is monitored down to 8 µm deep in a 30 × 30 µm2 area. Grains boundaries are reconstructed in three-dimensions via a twostep processing method, relying on the wavelet synchro-squeezed transform and the alpha shape algorithm. Imaging contrast is improved by taking advantage of stronger sensitivity to anisotropy of transverse acoustic waves, compared with longitudinal waves. Utilization of transverse waves in the image processing reveals additional boundaries that are not discerned using longitudinal waves, confirmed by an electron backscattering diffraction pattern. A buried inclined interface between differently oriented grains is identified by monitoring changes in amplitude (phase) of the portion of the signal associated with transverse (longitudinal) waves. Estimates of the inclination angle of this interface prove the sensitivity of our laser ultrasonic method to image inclined boundaries.

36 MATERIALS SCIENCE↗