Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Defect”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

Anomalous effects in silicon solar cell irradiated by 1-MeV protons

Several silicon solar cells having thicknesses of approximately 63 microns, with and without back-surface fields (BSF), were irradiated with 1-MeV protons having fluences between 10 to the 10th and 10 to the 12th sq cm. The irradiations were performed using both normal and isotropic incidence on the rear surfaces of the cells. It was observed that after irradiation with fluences greater than 10 to the 11th protons/sq cm, all BSF cells degraded at a faster rate than cells without BSF. The irradiation results are analyzed using a model in which irradiation-induced defects in the BSF region are taken into account. Tentatively, it is concluded that an increase in defect density due to the formation of aluminum and proton complexes in BSF cells is responsible for the higher-power loss in the BSF cells compared to the non-BSF cells.

Kachare, R.↗

Deformation and fracture of single-crystal and sintered polycrystalline silicon carbide produced by cavitation

An investigation was conducted to examine the deformation and fracture behavior of single-crystal and sintered polycrystalline SiC surfaces exposed to cavitation. Cavitation erosion experiments were conducted in distilled water at 25 C by using a magnetostrictive oscillator in close proximity (1 mm) to the surface of SiC. The horn frequency was 20 kHz, and the double amplitude of the vibrating disk was 50 microns. The results of the investigation indicate that the SiC (0001) surface could be deformed in a plastic manner during cavitation. Dislocation etch pits were formed when the surface was chemically etched. The number of defects, including dislocations in SiC (0001) surface, increased with increasing exposure time to cavitation. The presence of intrinsic defects such as voids in the surficial layers of the sintered polycrystalline SiC determined the zones at which fractured grains and fracture pits (pores) were generated. Single-crystal SiC had superior erosion resistance to that of sintered polycrystalline SiC.

Miyoshi, Kazuhisa↗

Improved Radiography Of Wooden Parts

Technique developed to increase radiographic contrasts of inherent latent defects in wood. Involves introduction of radiopaque substance into defect site and subjecting site to penetrating radiation. Radiopaque penetrant used is commercially available fluorocarbon cleaning solvent, trichlorotrifluoroethane. Applicable in inspection of wooden aircraft components, fan and wind-turbine blades, marine parts, insulators, and other wooden components, assemblies, and structures.

Berry, Maggie L.↗

Magnetic correlations in La(2-x)Sr(x)CuO4 from NQR relaxation and specific heat

La-139 and Cu-63 Nuclear Quadrupole Resonance (NQR) relaxation measurements in La(2-x)Sr(x)CuO4 for O = to or less than 0.3 and in the temperature range 1.6 + 450 K are analyzed in terms of Cu(++) magnetic correlations and dynamics. It is described how the magnetic correlations that would result from Cu-Cu exchange are reduced by mobile charge defects related to x-doping. A comprehensive picture is given which explains satisfactorily the x and T dependence of the correlation time, of the correlation length and of the Neel temperature T(sub n)(x) as well as being consistent with known electrical resistivity and magnetic susceptibility measurements. It is discussed how, in the superconducting samples, the mobile defects also cause the decrease, for T yields T(sub c)(+) of the hyperfine Cu electron-nucleus effective interaction, leading to the coexistence of quasi-localized, reduced magnetic moments from 3d Cu electrons and mobile oxygen p-hole carriers. The temperature dependence of the effective hyperfine field around the superconducting transition yields an activation energy which could be related to the pairing energy. New specific heat measurements are also presented and discussed in terms of the above picture.

Borsa, F.↗

Solubility and partitioning of Ar in anorthite, diopside, forsterite, spinel, and synthetic basaltic liquids

The solubility and partitioning of Ar in natural anorthite, diopside, forsterite, spinel, and synthetic iron-free basaltic melts was investigated using a new technique that obviates the postquenching phase separation. It was found that the solubility of Ar in the minerals was surprisingly high. Moreover, the solubility of Ar in different samples of a particular mineral run in the same experiment varied more than the solubility in the same sample run in different experiments, suggesting that noble gases are held in lattice vacancy defects. Moreover, the results of TEM imaging revealed no anomalous microstructures, while EXAFS studies of some samples showed that Kr has no preferred site in the lattices, supporting the defect siting conclusion.

Broadhurst, C. Leigh↗

Gallium arsenide solar cell radiation damage study

A thorough analysis has been made of electron- and proton- damaged GaAs solar cells suitable for use in space. It is found that, although some electrical parametric data and spectral response data are quite similar, the type of damage due to the two types of radiation is different. An I-V analysis model shows that electrons damage the bulk of the cell and its currents relatively more, while protons damage the junction of the cell and its voltages more. It is suggested that multiple defects due to protons in a strong field region such as a p/n junction cause the greater degradation in cell voltage, whereas the individual point defects in the quasi-neutral minority-carrier-diffusion regions due to electrons cause the greater degradation in cell current and spectral response.

Maurer, R. H.↗

Achieving dependability throughout the development process - A distributed software experiment

Distributed software engineering techniques and methods for improving the specification and testing phases are considered. With multiversion development, multiple implementations allow the use of an automated approach to testing called back-to-back (B/B) testing in which the outputs are compared to detect any discrepancies. However, a specification defect may lead to similar errors in the multiple versions and the underlying fault may not be detected with a B/B testing approach. The use of diverse formal specifications has been proposed as a solution to this problem, since defects in independently written specifications are likely to be different. To examine these issues, an experiment was performed using the design diversity approach in the specification, design, implementation, and testing of distributed software. In the experiment, three diverse formal specifications were used to produce multiple independent implementations of a distributed communication protocol in Ada. The problems encountered in building complex concurrent processing systems in Ada were also studied. Many pitfalls were discovered in mapping the formal specifications into Ada implementations.

Kelly, John P. J.↗

Effects of grain boundary characteristics of steel on magnetoacoustic emission spectra

Consideration is given to the effects of grain boundary characteristics on the properties of a magnetoacoustic emission spectra obtained by external ac magnetic field-driven domain wall motions. In studies with HY80 steel samples, it is found that the domain wall-defect interaction enhances as more grain boundary is introduced. The enhancement of the domain wall-defect interaction generates high amplitude magnetoacoustic emission pulses and reduces the rate of magnetoacoustic emission events by limiting domain wall motions.

Namkung, M.↗

Magnetic particle inspection

The purpose of this experiment is to familiarize the student with magnetic particle inspection and relate it to classification of various defects. Magnetic particle inspection is a method of detecting the presence of cracks, laps, tears, inclusions, and similar discontinuities in ferromagnetic materials such as iron and steel. This method will most clearly show defects that are perpendicular to the magnetic field. The Magnaglo method uses a liquid which is sprayed on the workpiece to be inspected, and the part is magnetized at the same time. The workpiece is then viewed under a black light, and the presence of discontinuity is shown by the formation of a bright indication formed by the magnetic particles over the discontinuity. The equipment and experimental procedures are described.

Sastri, Sankar↗

Ground and space based optical analysis of materials degradation in low-Earth-orbit

There is strong interest in being able to accurately and sensitively monitor materials degradation in both ground-based and space-based environments. Two optical techniques for sensitive degradation monitoring are reviewed: spectroscopic ellipsometry and photothermal spectroscopy. These techniques complement each other in that ellipsometry is sensitive to atomically thin surface and subsurface changes, and photothermal spectroscopy is sensitive to local defects, pin-holes, subsurface defects, and delamination. Progress in applying these spectroscopies (both ex situ and in situ) to atomic oxygen degradation of space materials is reviewed.

Woollam, John A.↗

The development and evaluation of an alternative powder prepregging technique for use with LaRC-TPI/graphite composites

An alternative powder prepregging method for use with LaRC-TPI (a thermoplastic polyimide)/graphite composites is investigated. The alternative method incorporates the idea of moistening the fiber prior to powder coating. Details of the processing parameters are given and discussed. The material was subsequently laminated into small coupons which were evaluated for processing defects using electron microscopy. After the initial evaluation of the material, no major processing defects were encountered but there appeared to be an interfacial adhesion problem. As a result, prepregging efforts were extended to include an additional fiber system, XAS, and a semicrystalline form of the matrix. The semicrystalline form of the matrix was the result of a complex heat treating cycle. Using scanning electron microscopy (SEM), the fiber/matrix adhesion was evaluated in these systems relative to the amorphous/XAS coupons. Based on these results, amorphous and semicrystalline/AS-4 and XAS materials were prepregged and laminated for transverse tensile testing. The results of these tests are presented, and in an effort to obtain more information on the effect of the matrix, remaining semicrystalline transverse tensile coupons were transformed back to the amorphous state and tested. The mechanical properties of the transformed coupons returned to the values observed for the original amorphous coupons, and the interfacial adhesion, as observed by SEM, was better than in any previous sample.

Ogden, Andrea L.↗

Parametric study in weld mismatch of longitudinally welded SSME HPFTP inlet

Welded joints are an essential part of pressure vessels such as the Space Shuttle Main Engine (SSME) Turbopumps. Defects produced in the welding process can be detrimental to weld performance. Recently, review of the SSME high pressure fuel turbopump (HPFTP) titanium inlet x rays revealed several weld discrepancies such as penetrameter density issues, film processing discrepancies, weld width discrepancies, porosity, lack of fusion, and weld offsets. Currently, the sensitivity of welded structures to defects is of concern. From a fatigue standpoint, weld offset may have a serious effect since local yielding, in general, aggravates cyclic stress effects. Therefore, the weld offset issue is considered. Using the finite element method and mathematical formulations, parametric studies were conducted to determine the influence of weld offsets and a variation of weld widths in longitudinally welded cylindrical structures with equal wall thickness on both sides of the joint. From the study, the finite element results and theoretical solutions are presented.

Min, J. B.↗

NDE of thermal protection system for space shuttle solid rocket booster

Potential nondestructive test (NDE) methods were evaluated for detecting debonds and weak bonds in the thermal protection system (TPS) for the space shuttle solid rocket boosters. The primary thermal protection material is a sprayable, thick epoxy coating that is filled with lightweight and thermal insulating materials. Test panels were fabricated with a wide variety of hidden realistic defects, including contact debonds and weak bonds. Nondestructive test results were obtained. Candidate NDE methods evaluated for booster production applications include laser interferometry (e.g., electronic shearography), infrared thermography, radiography (e.g., computed tomography), acousto-ultrasonics, mechanical/acoustic impedance, ultrasonics, acoustic emission, and the tap test. Capabilities, advantages, disadvantages, and relative performances in defect detection of each test method for TPS bonding applications are reported. Electronic shearography NDE was technically the superior method for detecting debonds.

Myers, R. S.↗

Damage development under compression-compression fatigue loading in a stitched uniwoven graphite/epoxy composite material

Damage initiation and growth under compression-compression fatigue loading were investigated for a stitched uniweave material system with an underlying AS4/3501-6 quasi-isotropic layup. Performance of unnotched specimens having stitch rows at either 0 degree or 90 degrees to the loading direction was compared. Special attention was given to the effects of stitching related manufacturing defects. Damage evaluation techniques included edge replication, stiffness monitoring, x-ray radiography, residual compressive strength, and laminate sectioning. It was found that the manufacturing defect of inclined stitches had the greatest adverse effect on material performance. Zero degree and 90 degree specimen performances were generally the same. While the stitches were the source of damage initiation, they also slowed damage propagation both along the length and across the width and affected through-the-thickness damage growth. A pinched layer zone formed by the stitches particularly affected damage initiation and growth. The compressive failure mode was transverse shear for all specimens, both in static compression and fatigue cycling effects.

Vandermey, Nancy E.↗

Low Earth orbital atomic oxygen micrometeoroid, and debris interactions with photovoltaic arrays

Polyimide Kapton solar array blankets can be protected from atomic oxygen in low earth orbit if SiO sub x thin film coatings are applied to their surfaces. The useful lifetime of a blanket protected in this manner strongly depends on the number and size of defects in the protective coatings. Atomic oxygen degradation is dominated by undercutting at defects in protective coatings caused by substrate roughness and processing rather than micrometeoroid or debris impacts. Recent findings from the Long Duration Exposure Facility (LDEF) and ground based studies show that interactions between atomic oxygen and silicones may cause grazing and contamination problems which may lead to solar array degradation.

Banks, Bruce A.↗

Image gathering and digital restoration for fidelity and visual quality

The fidelity and resolution of the traditional Wiener restorations given in the prevalent digital processing literature can be significantly improved when the transformations between the continuous and discrete representations in image gathering and display are accounted for. However, the visual quality of these improved restorations also is more sensitive to the defects caused by aliasing artifacts, colored noise, and ringing near sharp edges. In this paper, these visual defects are characterized, and methods for suppressing them are presented. It is demonstrated how the visual quality of fidelity-maximized images can be improved when (1) the image-gathering system is specifically designed to enhance the performance of the image-restoration algorithm, and (2) the Wiener filter is combined with interactive Gaussian smoothing, synthetic high edge enhancement, and nonlinear tone-scale transformation. The nonlinear transformation is used primarily to enhance the spatial details that are often obscurred when the normally wide dynamic range of natural radiance fields is compressed into the relatively narrow dynamic range of film and other displays.

Huck, Friedrich O.↗

Interfacial analysis of tribological systems containing molybdenum disulfide and iron using XPS and CEMS

In the present evaluation of results from studies of the interfacial chemistry and morphology of a buried lubricant-substrate interface, specimens of increasing complexity that culminated with the effects of excess sulfur and defects were characterized by XPS and SEM, as well as conversion-electron Moessbauer spectroscopy (CEMS). In order to simulate sputtered systems, single crystals of MoS2 were damaged with Ar(+) bombardment and coated with Fe. Fe is found to react differently with MoS2 depending on surface treatments, surface defects, annealing treatments, and the presence of excess sulfur. The annealing temperature determines which compounds are formed, as well as the crystal habit and plane at the Fe-MoS2 interface.

Zabinski, J. S.↗

The effect of atomic oxygen on altered and coated Kapton surfaces for spacecraft applications in low earth orbit

A commercially applied silicon oxide coating on Kapton and an alternative material with Si groups on the surface were evaluated for durability with respect to atomic oxygen in both a random plasma and a directed atomic oxygen beam system. It is found that the alternative to Kapton, DuPont 93-1, is not adequately protecting to last 15 years in LEO, the desired operation time of the Space Station Freedom. The coated Kapton is considered to be promising due to the adherence of the coating and lack of extensive tearing at undercut defect sites. Fewer defects in the coating and elimination of long scratches and uncoated areas would substantially improve the durability of this material.

Rutledge, Sharon K.↗