Thermal energy storage research and development program final technical report, 6 dec. 1960 - 1 dec. 1961
Thermal energy storage materials for use in solar thermionic power spacecraft systems
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Thermal energy storage materials for use in solar thermionic power spacecraft systems
The thermoradiative cell is a new method for converting heat energy to electrical power, first detailed by Strandberg in 2015. The cell is structurally similar to a photovoltaic cell, in that it is a p-n junction semiconductor device, but thermodynamically operates in the reverse direction, converting the thermal dark current into electrical power by utilizing the recombination radiation from thermally-generated electron hole pairs to radiate waste heat to space. This technology may have application for space missions in converting thermal energy produced by a radioisotope source or from a nuclear reactor into power. The power and efficiency can be calculated as a function of bandgap in the detailed-balance case (the Shockley-Queisser limit), in which all of the thermal emissivity of the cell is due to the recombination of thermally generated electron-hole pairs, and all other recombination losses are ignored. The current produced is directly proportional to the recombination radiation, and thus the more thermally generated pairs, the higher the current. The voltage is proportional to the external bias. These two constraints allow optimization of the optimum bias point for maximum power, and allow calculation of the efficiency at maximum power point. Unlike photovoltaic cells, the maximum power operating point is not the same as the maximum efficiency point, and higher efficiency can be achieved at a higher (negative) bias in the ideal case. Incorporating non-ideal losses, however, shifts the maximum efficiency point toward lower bias. Since a thermoradiative cell operates by radiating directly to space, the current produced by a themoradiative cells will increase with the Stefan-Boltzman radiative efficiency; roughly the fourth power of the temperature. Thus, in contrast to a photovoltaic converter, the power produced is highest at high operating temperatures. Likewise, in contrast to conventional thermal conversion, high radiator temperature increases, rather than decreases the efficiency. Thus, the thermoradiative conversion may fill a mission niche in which small radiator size is required. The basic operation will be summarized, applications to space power discussed, and the requirements for further research outlined.
We have prepared composite materials of hexagonal nickel phosphide and molybdenum carbide (Mo2C) utilizing a simple and scalable two-stage synthesis method comprised of carbothermic reduction followed by hydrothermal incubation. We observe the monophasic hexagonal phosphide Ni2P in the composite at low phosphide-to-carbide (P:C) ratios. Upon increasing the proportion of P:C, the carbide surface becomes saturated, and we detect the emergence of a second hexagonal nickel phosphide phase (Ni5P4) upon annealing. We demonstrate that vapor-phase upgrading (VPU) of whole biomass via catalytic fast pyrolysis is achievable using the composite material as a catalyst, and we monitor the resulting product slates using pyrolysis gas chromatography/mass spectrometry. Our analysis of the product vapors indicates that variation of the P:C molar ratio in the composite material affords product slates of varying complexity and composition, which is indicated by the number of products and their relative proportions in the product slate. Our results demonstrate that targeted vapor product composition can be obtained, which can potentially be utilized to tune the composition of the bio-oil downstream.
Not Available
In this book, expert authors describe advanced solar photon conversion approaches that promise highly efficient photovoltaic and photoelectrochemical cells with sophisticated architectures on the one hand, and plastic photovoltaic coatings that are inexpensive enough to be disposable on the other. Their leitmotifs include light-induced exciton generation, junction architectures that lead to efficient exciton dissociation, and charge collection by percolation through mesoscale phases. Photocatalysis is closely related to photoelectrochemistry, and the fundamentals of both disciplines are covered in this volume.
Cornerstone Resources has developed a proprietary advanced preprocessing technology, the BurCell® System, for production of a high quality organic biomass feedstock from numerous waste resources. While suitable for a variety of feedstock, the focus of development for the BurCell® System has been thus far Municipal Solid Waste (MSW). In MSW, the system technology is able to capture non-recyclable waste paper, cardboard, and organic materials, homogenize these materials and allow for separation of the non-organic fraction. The resulting homogenized organic material typically represents in excess of 50% of the raw MSW feed. The recently released Billion Ton Study now includes MSW as a feedstock resource showing it to be one of the lowest cost and most widely distributed biomass resources available; however, acknowledging the concerns with the potential physical and chemical variability of an MSW based feedstock stream. The focus on MSW has also been driven by MSW being a resource with a clear, well understood and mature supply-chain. Treating MSW in the BurCell® System will make that source of biomass substantially more accessible. To further promote the use of this MSW derived biomass and beneficially exploit the use of the BurCell® System for processing of biomass for Bioenergy production facilities, more detailed lab data is now required
An attempt is made to provide both the WEFAX user and the APT user with the basic equipments necessary to convert present equipment to the new SMS WEFAX frequency. This conversion is simple and, as in all communication systems, can be accomplished by innumerable approaches. The approach used here assumed commercial purchase of components and integration by the user into his system. This conversion requires no modification to existing equipment and is simply an RF conversion from S-band to the present VHF frequencies.
The results are presented of nine months of technical study of non-photovoltaic options for the generation of electricity for terrestrial use by satellite power stations (SPS). A concept for the augmentation of ground-based solar power plants by orbital sunlight reflectors was also studied. Three SPS types having a solar energy source and two which used nuclear reactors were investigated. Data derived for each included: (1) configuration definition, including mass statement; (2) information for use in environmental impact assessment; (3) energy balance (ratio of energy produced to that required to achieve operation), and (4) development and other cost estimates. Cost estimates were dependent upon the total program (development, placement and operation of a number of satellites) which was postulated. This postulation was based upon an analysis of national power capacity trends and guidelines received from MSFC.
Calculations are performed to determine the dynamic effects of mechanical power transmission from the nacelle of a horizontal axis wind machine to the ground or to an intermediate level. It is found that resonances are likely at 2 or 4/REV, but they occur at low power only, and seem easily correctable. Large reductions are found in the harmonic torque inputs to the generator at powers near rated.
Based on a survey of current local area network technology with special attention paid to high bandwidth and very low transport delay requirements, NASA's Langley Research Center designed a new simulation subsystem using the computer automated measurement and control (CAMAC) network. This required significant modifications to the standard CAMAC system and development of a network switch, a clocking system, new conversion equipment, new consoles, supporting software, etc. This system is referred to as the advanced real-time simulation (ARTS) system. It is presently being built at LaRC. This paper provides a functional and physical description of the hardware and a functional description of the software. The requirements which drove the design are presented as well as present performance figures and status.
The research provided data on applicability of agricultural energy crops and forest biomass production and logistics models. While much of the overall research effort was focused on lignocellulosic feedstocks, the research also recognized that there are important opportunities for the production and use of starch-based agricultural crops to serve as alternative regionally-appropriate biofuel feedstocks. Also, the research identified fractionation techniques that can be used to separate biomass feedstocks into their basic chemical constituents and then streamline the biorefining industry by developing commodity products for cellulose, hemicellulose, and lignin. Finally, models and techniques were developed to determine economically feasible technologies for production of biomass-derived synthesis gases that can be used for clean, renewable power generation and for production of liquid transportation fuels through Fischer-Tropsch Synthesis. Moreover, this research program educated the next generation of engineers and scientists needed to implement these technologies.
Explore the source record for details and available documents.
The conversion of the Aerodynamic Preliminary Analysis System (APAS) software from a Silicon Graphics UNIX-based platform to a DOS-based IBM PC compatible is discussed. Relevant background information is given, followed by a discussion of the steps taken to accomplish the conversion and a discussion of the type of problems encountered during the conversion. A brief comparison of aerodynamic data obtained using APAS with data from another source is also made.
The goal of the Upstream Tool is to allow the user to customize key parameters specific to their case study or desired scenario, and generate customized results quickly and simply. The results calculated can be allocated, as upstream emissions, to a conversion facility or system of the user’s choice. The combination of the upstream and combustion emissions provide a quick estimate of the overall emissions from an entire energy conversion system.
Bismuth telluride (Bi 2 Te 3 ) and its alloys have been widely investigated as thermoelectric materials for cooling applications at around room temperature. We report here a systematic study on many compounds in the Bi 2 Te 3 –Bi 2 Se 3 –Bi 2 S 3 system. All the samples were fabricated by high energy ball milling followed by hot pressing. Among the investigated compounds, Bi 2 Te 2 S 1 shows a peak ZT ~0.8 at 300 °C and Bi 2 Se 1 S 2 ~0.8 at 500 °C. The results show that these compounds can be used for mid-temperature power generation applications. The leg efficiency of thermoelectric conversion for segmented elements based on these n-type materials could potentially reach 12.5% with a cold side at 25 °C and a hot side at 500 °C if appropriate p-type legs are paired, which could compete well with the state-of-the-art n-type materials within the same temperature range, including lead tellurides, lead selenides, lead sulfides, filled-skutterudites, and half Heuslers.
The flat-panel detector (FPD) is the state-of-the-art detector for digital radiography. The FPD can acquire images in real-time, has superior spatial resolution, and is free of the problems of x-ray image intensifiers--veiling glare, pin-cushion and magnetic distortion. However, FPDs suffer from poor signal to noise ratio performance at typical fluoroscopic exposure rates where the quantum noise is reduced to the point that it becomes comparable to the fixed electronic noise. It has been shown previously that avalanche multiplication gain in amorphous selenium (a-Se) can provide the necessary amplification to overcome the electronic noise of the FPD. Avalanche multiplication, however, comes with its own intrinsic contribution to the noise in the form of gain fluctuation noise. In this article a cascaded systems analysis is used to present a modified metric related to the detective quantum efficiency. The modified metric is used to study a diagnostic x-ray imaging system in the presence of intrinsic avalanche multiplication noise independently from other noise sources, such as electronic noise. An indirect conversion imaging system is considered to make the study independent of other avalanche multiplication related noise sources, such as the fluctuations arising from the depth of x-ray absorption. In this case all the avalanche events are initiated at the surface of the avalanche layer, and there are no fluctuations in the depth of absorption. Experiments on an indirect conversion x-ray imaging system using avalanche multiplication in a layer of a-Se are also presented. The cascaded systems analysis shows that intrinsic noise of avalanche multiplication will not have any deleterious influence on detector performance at zero spatial frequency in x-ray imaging provided the product of conversion gain, coupling efficiency, and optical quantum efficiency are much greater than a factor of 2. The experimental results show that avalanche multiplication in a-Se behaves as an intrinsic noise free avalanche multiplication, in accordance with our theory. Provided good coupling efficiency and high optical quantum efficiency are maintained, avalanche multiplication in a-Se has the potential to increase the gain and make negligible contribution to the noise, thereby improving the performance of indirect FPDs in fluoroscopy.
The Brayton Power Conversion Unit (BPCU) located at NASA Glenn Research Center (GRC) in Cleveland, Ohio was used to validate the results of a computational code known as Closed Cycle System Simulation (CCSS). Conversion system thermal transient behavior was the focus of this validation. The BPCU was operated at various steady state points and then subjected to transient changes involving shaft rotational speed and thermal energy input. These conditions were then duplicated in CCSS. Validation of the CCSS BPCU model provides confidence in developing future Brayton power system performance predictions, and helps to guide high power Brayton technology development.