Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMPRESSION TESTING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Physical Properties of Hilti HIT-RE 500 V3 After Irradiation: Slant Shear, Tensile, Flexural, and Compressive

There are various applications in which epoxy adhesives may be used within hot-cell environments. These epoxies currently see limited use within hot cells since it is known that organics see degradation after small doses even as low as 50 kilogray (kGy). These losses in physical property strengths limit the use of these epoxies to non-structural applications. In modern construction, however, the use of epoxies to bond structural components such as rebar or threaded anchors is becoming increasingly prevalent. To employ these types of materials the Idaho National Laboratory (INL) has begun investigating the specific degradation properties of epoxies for use in structural applications in environments where radiation is present. Hilti HIT-RE 500 V3 is used extensively in new construction and renovation projects across the world. The INL has conducted various tests on this epoxy for low dose environments. These tests include tensile, flexural, compression, and slant shear tests following the American Society for Testing Material International (ASTM) standards D638, D790, D695, and C882/882M respectively. Two sample sets for each test were created where the baseline specimens were not irradiated, and another set was irradiated to an accumulated dose of approximately 50-60 kGy. All the samples were destructively tested and analyzed focusing on the change in physical properties, examples of these tests are shown in Figures 1-4. Tensile testing results indicate a 0.9% loss in maximum load capacity, a 0.5% loss in tensile stress at maximum load, a 1.4% loss in tensile strain at break, and a 15% decrease in modulus of elasticity. Flexural testing results display an increase in all the following: 12% in strain at maximum load, 10% in maximum load capacity, 5% in stress at maximum load, and 3% in young’s modulus. The compressive physical properties after irradiation display a 1% increase in maximum load, a 3% decrease in stress at yield, and a 5% decrease in modulus of elasticity. The maximum compressive stress saw no measurable change after irradiation. The slant shear specimens after irradiation displayed a 2% increase in maximum load capacity and maximum compressive stress. Though a structural analysis would have to be completed as is normal for building design the increases and decreases in the measured physical properties indicate that this material may be used for structural applications in low dose hot-cell environments without adhesive failure.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Compressive strength of the plastic-bonded explosive surrogate idoxuridine under quasistatic and dynamic compression

Inert simulant materials, or “mocks”, are often used as surrogates for plastic-bonded explosives (PBX) in non-detonative tests in order to mitigate hazards. Mocks should reproduce as many non-detonative properties of the explosive as possible, including structural behavior in a variety of thermal and mechanical environments. Recently, the molecular crystal idoxuridine (IDOX) has been identified as an ideal mock for the main component in the explosive polymer-matrix composite PBX 9501, and has performed favorably under quasistatic loading conditions. Here, in order to assess robustness over a range of mechanical environments, plastic-bonded IDOX was compression tested from 0.001/s to 2000/s strain rates and compared to PBX 9501 historical data. Plastic-bonded IDOX showed good agreement to PBX 9501 across these strain rates, justifying continued development and production as a mock.

Burch, Alexandra C.↗
NASA NTRS1986

Aerodynamic instability performance of an advanced high-pressure-ratio compression component

The data acquisition and reduction, test procedures, and results of in-stall and in-surge testing of a NASA high-pressure-ratio compression component are discussed, in addition to the compressor-rig configuration and instrumentation used. Data analysis revealed information about rotating stall hysteresis, rotating stall development and cessation times, and rotating-stall-cell flow blockage. It is found that hysteresis exists in the work coefficient as well as in the pressure coefficient. Airflow rakes were designed to study the in-surge transient response of the compressor. The quasi-steady compressor characteristics underlying the transient-surge data were investigated using a parameter-identification technique.

Hosny, W. M.↗
NASA NTRS1936

Boosted performance of a compression-ignition engine with a displaced piston

Performance tests were made using a rectangular displacer arranged so that the combustion air was forced through equal passages at either end of the displacer into the vertical-disk combustion chamber of a single-cylinder, four-stroke-cycle compression-ignition test engine. After making tests to determine optimum displacer height, shape, and fuel-spray arrangement, engine-performance tests were made at 1,500 and 2,000 r.p.m. for a range of boost pressures from 0 to 20 inches of mercury and for maximum cylinder pressures up to 1,150 pounds per square inch. The engine operation for boosted conditions was very smooth, there being no combustion shock even at the highest maximum cylinder pressures. Indicated mean effective pressures of 240 pounds per square inch for fuel consumptions of 0.39 pound per horsepower-hour have been readily reproduced during routine testing at 2,000 r.p.m. at a boost pressure of 20 inches of mercury.

Moore, Charles S↗
DOE OSTI2023

Transition in helium bubble strengthening of copper from quasi-static to dynamic deformation

Damage from low-temperature irradiation and the subsequent degradation of materials performance pose significant challenges for the storage of radioactive materials and for peripheral components in some nuclear reactor designs. Fully understanding the mechanical behavior of such materials requires test data for strain rates in both the quasi-static (< 10/s) and dynamic (>> 10/s) regimes. While dynamic testing has generally been avoided in the past for neutron irradiated (contamination concerns) and ion irradiated (insufficient volume) materials, surface-sensitive Richtmyer-Meshkov instability (RMI) tests were used in the present work to overcome these limitations. Here, nanopillar compression, nanoindentation, and RMI testing data from a helium implanted surface layer (~10 µm thick) were compiled to explore the effects of helium bubbles on the materials strength of high-purity copper at strain rates of 0.001/s – 10 8 /s. While nano-mechanical testing revealed increases in yield strength and hardness with increasing helium dose from 1000 to 4000 appm He, RMI indicated no significant changes in strength as compared to unimplanted copper. Here, this discrepancy in behavior was rationalized through a combination of recent literature and follow-on molecular dynamics (MD) simulations, leading to the conclusion that the nanoscale helium bubbles acting as dispersed barriers to dislocation motion at quasi-static strain rates collapse under shock loading and cease to be effective barriers at high strain rates.

36 MATERIALS SCIENCE↗
NASA NTRS1987

Numerical simulation of homogeneous, isotropic, compressible turbulence

A new numerical algorithm is developed and applied to the direct simulation of compressible, homogeneous turbulent flows at low Mach numbers. A split method in time first solves a subset of the equations explicitly, followed by an implicit treatment of the pressure terms. The definition of an average sound speed over the entire field allows the implicit equations to be solved analytically, while relaxing the severe time limit imposed by the large sound speeds. Results from direct simulations on 96(3) grids provide a data base against which a new subgrid-scale model for compressible homogeneous turbulence is tested. This model reduces to the linear combination model in the absence of compressibility.

Erlebacher, G.↗
NASA NTRS1994

Compression of regions in the global advanced very high resolution radiometer 1-km data set

The global advanced very high resolution radiometer (AVHRR) 1-km data set is a 10-band image produced at USGS' EROS Data Center for the study of the world's land surfaces. The image contains masked regions for non-land areas which are identical in each band but vary between data sets. They comprise over 75 percent of this 9.7 gigabyte image. The mask is compressed once and stored separately from the land data which is compressed for each of the 10 bands. The mask is stored in a hierarchical format for multi-resolution decompression of geographic subwindows of the image. The land for each band is compressed by modifying a method that ignores fill values. This multi-spectral region compression efficiently compresses the region data and precludes fill values from interfering with land compression statistics. Results show that the masked regions in a one-byte test image (6.5 Gigabytes) compress to 0.2 percent of the 557,756,146 bytes they occupy in the original image, resulting in a compression ratio of 89.9 percent for the entire image.

Kess, Barbara L.↗
NASA NTRSDate not supplied

Experimental Methods Using Force Application of A Single Boom for A 500-M²-Class Solar Sail

Solar sailing missions rely on deployable systems for large area-to-mass ratios once in space, while still being small enough for launcher envelopes in the stowed configuration. Many of these deployable systems feature booms that are flattened and subsequently coiled onto a spool / hub. As part of a collaborative deployable space structures research effort between the National Aeronautics and Space Administration (NASA) and German Aerospace Center (DLR), a boom deployment system for a future 500 m² solar sail has been developed. To achieve the respective solar sail size goal, 16.5-m-long booms produced by NASA were integrated into a DLR-designed deployer mechanism. This considerable size, as well as the lightweight construction of the booms and respective deployable systems makes testing on the ground a significant challenge. Some systems for gravity compensation as well as vertical testing to minimize the influence of gravity have been used in the past. However, an uncertainty factor remains towards the behaviour in the space environment. The focus of this paper is the load application testing of the integrated boom-deployment mechanism system under microgravity condition, as well as a comparison to vertical testing under gravity. Testing in microgravity was performed during a parabolic flight test inside an aircraft and it included stowage and full deployment of a single boom along the longitudinal axis of the aircraft. The load application was split into two categories: static testing, which induced a linear force ramp to the static boom for either compression or compression-bending; and dynamic testing, which applied a constant force to a boom during extension provided by the deployer mechanism. Both types of tests were performed multiple times at two distinct lengths of the boom, fully deployed (12.76 m) and ~28.6 % deployed (3.65 m). More parameters that are vital to the test philosophy are the angles of attack in the force application and the highest force applied. The data acquisition used for the applied load and deflection measurements of the boom is also presented.

Martin Richter↗
NASA NTRSDate not supplied

Experimental Methods Using Force Application of A Single Boom for A 500-M²-Class Solar Sail

Solar sailing missions rely on deployable systems for large area-to-mass ratios once in space, while still being small enough for launcher envelopes in the stowed configuration. Many of these deployable systems feature booms that are flattened and subsequently coiled onto a spool / hub. As part of a collaborative deployable space structures research effort between the National Aeronautics and Space Administration (NASA) and German Aerospace Center (DLR), a boom deployment system for a future 500 m² solar sail has been developed. To achieve the respective solar sail size goal, 16.5-m-long booms produced by NASA were integrated into a DLR-designed deployer mechanism. This considerable size, as well as the lightweight construction of the booms and respective deployable systems makes testing on the ground a significant challenge. Some systems for gravity compensation as well as vertical testing to minimize the influence of gravity have been used in the past. However, an uncertainty factor remains towards the behaviour in the space environment. The focus of this paper is the load application testing of the integrated boom-deployment mechanism system under microgravity condition, as well as a comparison to vertical testing under gravity. Testing in microgravity was performed during a parabolic flight test inside an aircraft and it included stowage and full deployment of a single boom along the longitudinal axis of the aircraft. The load application was split into two categories: static testing, which induced a linear force ramp to the static boom for either compression or compression-bending; and dynamic testing, which applied a constant force to a boom during extension provided by the deployer mechanism. Both types of tests were performed multiple times at two distinct lengths of the boom, fully deployed (12.76 m) and ~28.6 % deployed (3.65 m). More parameters that are vital to the test philosophy are the angles of attack in the force application and the highest force applied. The data acquisition used for the applied load and deflection measurements of the boom is also presented.

Martin Richter↗
DOE OSTI2014

High-Current Cold Cathode Employing Diamond and Related Materials

The essence of this project was for diamond films to be deposited on cold cathodes to improve their emission properties. Films with varying morphology, composition, and size of the crystals were deposited and the emission properties of the cathodes that utilize such films were studied. The prototype cathodes fabricated by the methods developed during Phase I were tested and evaluated in an actual high-power RF device during Phase II. These high-power tests used the novel active RF pulse compression system and the X-band magnicon test facility at US Naval Research Laboratory. In earlier tests, plasma switches were employed, while tests under this project utilized electron-beam switching. The intense electron beams required in the switches were supplied from cold cathodes embodying diamond films with varying morphology, including uncoated molybdenum cathodes in the preliminary tests. Tests with uncoated molybdenum cathodes produced compressed X-band RF pulses with a peak power of 91 MW, and a maximum power gain of 16.5:1. Tests were also carried out with switches employing diamond coated cathodes. The pulse compressor was based on use of switches employing electron beam triggering to effect mode conversion. In experimental tests, the compressor produced 165 MW in a ~ 20 ns pulse at ~18× power gain and ~ 140 MW at ~ 16× power gain in a 16 ns pulse with a ~ 7 ns flat-top. In these tests, molybdenum blade cathodes with thin diamond coatings demonstrated good reproducible emission uniformity with a 100 kV, 100 ns high voltage pulse. The new compressor does not have the limitations of earlier types of active pulse compressors and can operate at significantly higher electric fields without breakdown.

36 MATERIALS SCIENCE↗
NASA NTRS1992

Behavior of compacted lunar simulants using new vacuum triaxial device

The objectives of this study are to create a lunar simulant locally from a basaltic rock and to design and develop a vacuum triaxial test device that can permit testing of compacted lunar simulant under cyclic loading with different levels of initial vacuum. Triaxial testing is performed in the device itself without removing the compacted specimen. Preliminary constrained compression and triaxial shear tests are performed to identify effects of initial confinements and vacuums. The results are used to define deformation and strength parameters. At this time, vacuum levels up to 0.0001 are possible. The research can aid in the development of compacted materials for various construction applications.

Desai, Chandra S.↗
NASA NTRS1977

Tensile and compressive behavior of Borsic/aluminum

The results of an experimental investigation of the mechanical behavior of Borsic/aluminum are presented. Composite laminates were tested in tension and compression for monotonically increasing load and also for variable loading cycles in which the maximum load was increased in each successive cycle. It is shown that significant strain-hardening, and corresponding increase in yield stress, is exhibited by the metal matrix laminates. For matrix dominated laminates, the current yield stress is essentially identical to the previous maximum stress, and unloading is essentially linear with large permanent strains after unloading. For laminates with fiber dominated behavior, the yield stress increases with increase in the previous maximum stress, but the increase in yield stress does not keep pace with the previous maximum stress. These fiber dominated laminates exhibit smaller nonlinear strains, reversed nonlinear behavior during unloading, and smaller permanent strains after unloading. Compression results from sandwich beams and flat coupons are shown to differ considerably. Results from beam specimens tend to exhibit higher values for modulus, yield stress, and strength.

Herakovich, C. T.↗
DOE OSTI2018

Mechanical behavior and texture development of over-aged and solution treated Al-Cu-Mg alloy during multi-directional forging

The effects of initial heat treatments, i.e. solution treating and over ageing, on deformation behavior of an age hardenable Al-Cu-Mg alloy, including mechanical properties and texture evolution, during multi-directional forging (MDF) are investigated. Hardness measurements, electron back scatter diffraction (EBSD) maps, and differential scanning calorimetry (DSC) are carried out. Mechanical behaviors of the alloy in terms of compressive stress and hardness test after MDF are investigated. In both solution treated and over-aged alloys, the compressive stress during MDF shows an increase up to the second pass, and by further straining the flow stress is decreased. However, shear and deformation bands are formed in both solution treated and over-aged alloys, the density of these instabilities in the solution treated alloy is higher than that in over-aged alloy. In the solution treated alloy, not only large particles induce deformation bands, but also the dynamically formed GPB zones/Cu-Mg co-clusters. Texture analysis shows that the shear component of C {001}<110> (Φ{sub 1} = 90°, Φ = 0°, Φ{sub 2} = 45°) is developed with 18 mrd during MDF of the over-aged alloy. In the solution treated alloy, due to the high density of deformation bands and different microchemistry of the matrix in comparison with that of the over-aged alloy, the Copper type texture component {112}<111> (Φ{sub 1} = 90°, Φ = 35°, Φ{sub 2} = 45°) is developed with 11 mrd.

36 MATERIALS SCIENCE↗
NASA NTRS1980

Effects of method of loading and specimen configuration on compressive strength of graphite/epoxy composite materials

Three test schemes were examined for testing graphite/epoxy (Narmco T300/5208) composite material specimens to failure in compression, including an adaptation of the IITRI "wedge grip" compression fixture, a face-supported-compression fixture, and an end-loaded-coupon fixture. The effects of specimen size, specimen support arrangement and method of load transfer on compressive behavior of graphite/epoxy were investigated. Compressive stress strain, strength, and modulus data obtained with the three fixtures are presented with evaluations showing the effects of all test parameters, including fiber orientation. The IITRI fixture has the potential to provide good stress/strain data to failure for unidirectional and quasi-isotropic laminates. The face supported fixture was found to be the most desirable for testing + or - 45 s laminates.

Clark, R. K.↗