Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMBUSTION PROPERTIES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

Effect of Coal Properties and Operation Conditions on Flow Behavior of Coal Slag in Entrained Flow Gasifiers: A Brief Review

Integrated gasification combined cycle (IGCC) is a potentially promising clean technology with an inherent advantage of low emissions, since the process removes contaminants before combustion instead of from flue gas after combustion, as in a conventional coal steam plant. In addition, IGCC has potential for cost-effective carbon dioxide capture. Availability and high capital costs are the main challenges to making IGCC technology more competitive and fully commercial. Experiences from demonstrated IGCC plants show that, in the gasification system, low availability is largely due to slag buildup in the gasifier and fouling in the syngas cooler downstream of the gasification system. In the entrained flow gasifiers used in IGCC plants, the majority of mineral matter transforms to liquid slag on the wall of the gasifier and flows out the bottom. However, a small fraction of the mineral matter (as fly ash) is entrained with the raw syngas out of the gasifier to downstream processing. This molten/sticky fly ash could cause fouling of the syngas cooler. Therefore, it is preferable to minimize the quantity of fly ash and maximize slag. In addition, the hot raw syngas is cooled to convert any entrained molten fly slag to hardened solid fly ash prior to entering the syngas cooler. To improve gasification availability through better design and operation of the gasification process, better understanding of slag behavior and characteristics of the slagging process are needed. Slagging behavior is affected by char/ash properties, gas compositions in the gasifier, the gasifier wall structure, fluid dynamics, and plant operating conditions (mainly temperature and oxygen/carbon ratio). The viscosity of the slag is used to characterize the behavior of the slag flow and is the dominating factor to determine the probability that ash particles will stick. Slag viscosity strongly depends on the temperature and chemical composition of the slag. Because coal has varying ash content and composition, different operating conditions are required to maintain the slag flow and limit problems downstream. This report briefly introduces the IGCC process, the gasification process, and the main types and operating conditions of entrained flow gasifiers used in IGCC plants. This report also discusses the effects of coal ash and slag properties on slag flow and its qualities required for the entrained flow gasifier. Finally this report will identify the key operating conditions affecting slag flow behaviors, including temperature, oxygen/coal ratio, and flux agents.

01 COAL, LIGNITE, AND PEAT↗

Experimental and numerical investigation of ester droplet combustion: Application to butyl acetate

This paper presents an experimental and numerical study of the combustion of isolated n–butyl acetate droplets in the standard atmosphere. Numerical simulations are reported using a model that incorporates unsteady gas and liquid transport, variable properties, and radiation. Three skeletal mechanisms of n-butyl acetate, derived from a large detailed mechanism comprised of 819 species and 52,698 reactions, were used in the numerical simulations to evaluate the influence of the kinetic mechanism on burning. The reduced mechanisms comprised 212 species and 5413 reactions, 157 species and 3089 reactions, and 105 species and 1035 reactions. The numerical model did not include soot formation, though qualitatively mild sooting was noted only for droplets larger than 0.7 mm. The numerical predictions were in good agreement with experimental measurements of droplet and flame diameters. Flame extinction was numerically predicted which was attributed to a decrease of the characteristic diffusion time relative to the chemical time as droplet burned. Effects of initial droplet diameter on the evolution of maximum gas temperature (T max ) and peak mole fractions of CO 2 and CO are also examined numerically.

09 BIOMASS FUELS↗

Parametric Testing and Evaluation of a Novel Biphasic Absorption Process for Post-Combustion Carbon Capture

A novel biphasic CO2 absorption process (BiCAP) is being developed at the University of Illinois. BiCAP is enabled by using a new class of biphasic solvents developed based on multi-property criteria for postcombustion carbon capture. The process was previously demonstrated at the lab-scale, including in 10 kWe absorption and desorption column systems. In the current study, the process has been scaled up by building and testing a 40 kWe integrated capture skid at a power plant. Parametric tests for two biphasic solvents were conducted with the synthetic flue gas made of bottle CO2 gas and air to validate the performance and operational flexibility of the unit with respect to varying process or operating conditions. Operation of the phase separator, which is unique equipment to BiCAP, was verified to be stable and efficient. Two liquid phases could be separated via static settlement based on a density difference and >90% of the CO2 absorbed was concentrated in the separated CO2-rich phase. Results of parametric tests showed that the minimum heat duty appeared at the optimal stripping pressure. A higher stripping temperature was more favourable to improve overall energy performance. Introducing a secondary cold solvent feed stream to the top of the stripper via bypassing the cross heat exchanger helped reduce the heat loss carried with water vapour. Test results also revealed that the heat duty requirement was comparable when the CO2 concentration in flue gas decreased from ~11 to 4 vol.% as the phase separation decoupled the absorption and desorption steps in BiCAP. Under typical steady-state conditions, both biphasic solvents lowered the process heat duty by >40% compared with the reference 30 wt.% monoethanolamine solvent.

Absorption↗

Preparation of Cu and Fly Ash Composite by Powder Metallurgy Technique

Cu and Fly Ash (FA) mixtures with different weight percentages were prepared. Pellets of the mixture powder were produced with the dimension of 17.7 mm in diameter and 10-15 mm in height. These different composites were compacted at a constant pressure of 280 MPa. One of the selected weight percentages was then compacted to form into pellet and sintered at different temperatures which were at 900, 950 and 1000 deg. C respectively for 2 hours. Density of green pellet was measured before sintered in furnace. After sintering, all the pellets with different temperatures were re-weighed and sintered density were calculated. The densification of the green and sintered pellets was required to be measured as one of the parameter in selection of the best material properties. Porosity of the pellet shall not be ignored in order to analyze the close-packed particles stacking in the pellet. SEM micrograph had been captured to observe the presence of pores and agglomeration of particles in the sample produced.

36 MATERIALS SCIENCE↗

Relative Role of Particle Size and Shape on the Magnetic and Catalytic Behavior of Nanozinc Chromite

The purpose of this study is to define an effective synthesis for spinel-type zinc chromite (ZnCr{sub 2}O{sub 4}) nanoparticles by a simple microwave combustion method. The synthesized material was analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and from optical properties. A magnetic property for the material was examined through the vibrating sample magnetism. The distribution of the external magnetic lines of force and the self-generated magnetic field of ferromagnetic materials was taken into account in the presence of an external magnetic field. Zinc chromite showed good performances in catalytic oxidation, and the role of particle size and shape is highlighted.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Understanding how chemical structure affects ignition-delay-time $\phi$-sensitivity

$\phi$-sensitivity is the change in ignition delay time (IDT) with respect to the fuel-to-air equivalence ratio ($\phi$). High $\phi$-sensitivity is a desirable fuel property for applications in advanced compression ignition and multi-mode engine designs. Understanding how $\phi$-sensitivity depends on chemical structure is essential for selecting promising biofuels from the ever-growing list of proposed candidates. Here, we investigate the effect of chemical structure on $\phi$-sensitivity with experiment, simulation, and theory. Experimental Advanced Fuel Ignition Delay Analyzer (AFIDA) measurements for 2,4-dimethylpentane and diisopropyl ether provide evidence that branching and functional groups strongly impact $\phi$-sensitivity. Further insights into this dependence are obtained with 0-D kinetic simulations with existing mechanisms for n-pentane, diethyl ether, 3-pentanone, n-heptane, 2-methylhexane, 2,4-dimethylpentane, and 2,2,3-trimethylbutane. Quantum mechanical (QM) G4 calculations of low-temperature reactions help explain the observed experimental and simulation trends. Specifically, these QM calculations provide theoretical estimates of the ketohydroperoxide (KHP) dissociation rates, the HO 2 formation rates from peroxy radical (ROO), and the “cross-over” temperatures, i.e., the temperature at which ROO dissociation is favored compared to hydroperoxyl radical (QOOH) formation. Each of these reaction rates is compared to the n-alkane reference point to determine the impact of branching and different functional groups. Although kinetic mechanisms typically assume that KHP dissociation rates are invariant of chemical environment, our QM results suggest that this rate can span a range of roughly two orders of magnitude. We also discuss the importance of including the peroxy-hydroperoxy (OO-OOH) hydrogen transfer reaction for branched ethers. Finally, the insights gained assist in proposing a highly $\phi$-sensitive compound, namely, isopropyl propyl ether.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Rapid synthesis of room temperature ferromagnetic Ag-doped LaMnO{sub 3} perovskite phases by the solution combustion method

We report the rapid solution combustion synthesis and characterization of Ag-substituted LaMnO{sub 3} phases at relatively low temperature using oxalyl dihydrazide, as fuel. Structural parameters were refined by the Rietveld method using powder X-ray diffraction data. While the parent LaMnO{sub 3} crystallizes in the orthorhombic structure, the Ag-substituted compounds crystallize in the rhombohedral symmetry. On increasing Ag-content, unit cell volume and Mn-O-Mn bond angle decreases. The Fourier transform infra red spectrum shows two absorption bands corresponding to Mn-O stretching vibration ({nu}{sub s} mode) and Mn-O-Mn deformation vibration ({nu}{sub b} mode) around 600 cm{sup -1} and 400 cm{sup -1} for the compositions, x = 0.0, 0.05 and 0.10, respectively. Electrical resistivity measurements reveal that composition-controlled metal to insulator transition, with the maximum metal to insulator being 280 K for the composition La{sub 0.75}Ag{sub 0.25}MnO{sub 3}. Increase in magnetic moment was observed with increase in Ag-content. The maximum magnetic moment of 35 emu/g was observed for the composition La{sub 0.80}Ag{sub 0.20}MnO{sub 3}.

36 MATERIALS SCIENCE↗

Impact of humidity on gas transport in polybenzimidazole membranes

Polybenzimidazoles (PBIs) are promising materials for high temperature H 2 /CO 2 separation in applications such as steam reforming and pre-combustion carbon capture where significant amounts of water are often present. However, PBIs are hydrophilic, and the impact of humidity on PBI gas separation properties is relatively unexplored. Furthermore, opportunity exists to elucidate the interplay between plasticization, free volume, and gas transport in glassy polymer membranes such as PBIs. Here, this study investigates the effect of humidity on H 2 , O 2 , and CO 2 permeabilities at 35 °C in a commercial PBI and two sulfone-containing PBIs. Water uptake significantly reduces PBI gas permeabilities at low humidities due to competitive sorption and antiplasticization. At high humidities, plasticization increases the permeabilities of larger gases in more hydrophilic PBIs. Effective fractional free volumes evaluated from gas permeation data and previously reported water sorption and dilation data suggest water plasticizes PBIs by increasing accessible free volume via enhanced molecular dynamics rather than by creating new free volume cavities.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Making Coal Relevant for Small Scale Applications: Modular Gasification for Syngas/Engine CHP Applications in Challenging Environments

The proposed project includes construction and operation of a power plant consisting of coal gasification facilities and engine generators which would produce electrical power and heat. The recovered heat and a portion of the carbon dioxide emissions from the engines would support an onsite greenhouse and other heat and power customers. The proposed project site is located on the Marathon North Pole Terminal property in North Pole, Alaska. Two gasifiers would convert the coal into syngas, which would be fed through a gas cleanup train and then combusted in six reciprocating engines driving electric generators. Heat recovery on the engine cooling loops and exhaust trains would provide heat to a glycol/water circulation system for use in the greenhouse, in the Marathon facilities and for other customers. Natural gas would fuel two additional engine generators and would also be available to supplement the syngas-fired engines.

01 COAL, LIGNITE, AND PEAT↗

Characterization of Particulate Matter Emissions from Heavy-Duty Partially Premixed Compression Ignition with Gasoline-Range Fuels

In this study, the compression ratio of a commercial 15L heavy-duty diesel engine was lowered and a split injection strategy was developed to promote partially premixed compression ignition (PPCI) combustion. Various low reactivity gasoline-range fuels were compared with ultra-low-sulfur diesel fuel (ULSD) for steady-state engine performance and emissions. Specially, particulate matter (PM) emissions were examined for their mass, size and number concentrations, and further characterized by organic/elemental carbon analysis, chemical speciation and thermogravimetric analysis. As more fuel-efficient PPCI combustion was promoted, a slight reduction in fuel consumption was observed for all gasoline-range fuels, which also had higher heating values than ULSD. Since mixing-controlled combustion dominated the latter part of the combustion process, hydrocarbon (HC) and carbon monoxide (CO) emissions were only slightly increased with the gasoline-range fuels. In contrast, soot emissions were significantly reduced with the gasoline-range fuels, including a ~70% reduction in micro soot sensor measurements and a >50% reduction in smoke meter measurements. All gasoline-range fuel PM samples were also found to contain higher amount of volatile species and organic carbon fractions compared to ULSD PM samples as measured by thermogravimetric and EC-OC analyses. Various partially oxidized HC species and nitrophenolic compounds were also detected by TDP-GC-MS and CE-MS techniques, which implied that more pronounced PPCI combustion occurred with the gasoline-range fuels. As a whole similar PM oxidation behavior was observed despite the differences in reactivity and chemical properties of the fuels, even though there may be some significant impacts under certain operating conditions.

33 ADVANCED PROPULSION SYSTEMS↗

Impact of biomass burning aerosols on radiation, clouds, and precipitation over the Amazon: relative importance of aerosol–cloud and aerosol–radiation interactions

Biomass burning (BB) aerosols can influence regional and global climate through interactions with radiation, clouds, and precipitation. Here, we investigate the impact of BB aerosols on the energy balance and hydrological cycle over the Amazon Basin during the dry season. We performed simulations with a fully coupled meteorology–chemistry model, the Weather Research and Forecasting model coupled with Chemistry (WRF-Chem), for a range of different BB emission scenarios to explore and characterize nonlinear effects and individual contributions from aerosol–radiation interactions (ARIs) and aerosol–cloud interactions (ACIs). The ARIs of BB aerosols tend to suppress low-level liquid clouds by local warming and increased evaporation and to facilitate the formation of high-level ice clouds by enhancing updrafts and condensation at high altitudes. In contrast, the ACIs of BB aerosol particles tend to enhance the formation and lifetime of low-level liquid clouds by providing more cloud condensation nuclei (CCN) and to suppress the formation of high-level ice clouds by reducing updrafts and condensable water vapor at high altitudes (>8 km). For scenarios representing the lower and upper limits of BB emission estimates for recent years (2002–2016), we obtained total regional BB aerosol radiative forcings of –0.2 and 1.5 W m –2 , respectively, showing that the influence of BB aerosols on the regional energy balance can range from modest cooling to strong warming. We find that ACIs dominate at low BB emission rates and low aerosol optical depth (AOD), leading to an increased cloud liquid water path (LWP) and negative radiative forcing, whereas ARIs dominate at high BB emission rates and high AOD, leading to a reduction of LWP and positive radiative forcing. In all scenarios, BB aerosols led to a decrease in the frequency of occurrence and rate of precipitation, caused primarily by ACI effects at low aerosol loading and by ARI effects at high aerosol loading. The dependence of precipitation reduction on BB aerosol loading is greater in a strong convective regime than under weakly convective conditions. Overall, our results show that ACIs tend to saturate at high aerosol loading, whereas the strength of ARIs continues to increase and plays a more important role in highly polluted episodes and regions. This should hold not only for BB aerosols over the Amazon, but also for other light-absorbing aerosols such as fossil fuel combustion aerosols in industrialized and densely populated areas. The importance of ARIs at high aerosol loading highlights the need for accurately characterizing aerosol optical properties in the investigation of aerosol effects on clouds, precipitation, and climate.

54 ENVIRONMENTAL SCIENCES↗

Modeling of dense sprays from LOX/H2 coaxial injectors under supercritical conditions

Assumptions commonly employed in the analytical description of a thin spray become unacceptable as the droplet density and droplet volume displacement become large. Changes in the semiempirical models describing drop-drop or drop-gas interactions as well as in the basic modeling approach itself may be necessary. A number of efforts undertaken to improve such models of the atomization-evaporation process to render them applicable in the dense-spray, supercritical regime are described. The improvements include those for variable drop density, supercritical properties, stripping evaporation and drop reincorporation into the liquid stream. The models are developed for use with the ARICC three-phase finite difference combustion code. Selected results from a sample calculation are presented, demonstrating the enhanced realism achievable with the upgraded models.

Liang, P. Y.↗

Modelling of jet- and swirl-stabilized reacting flows in axisymmetric combustors

Turbulent nonreactive and reactive flows with and without swirl are analyzed, with particular attention given to the flow fields of a gas-fueled nonpremixed swirl-stabilized combustor and a premixed opposed-jet combustor. Local mean flow properties, including velocity, temperature, and major species concentrations, are calculated by solving numerically the governing partial differential equations with associated submodels for turbulence and combustion. The results of the study indicate that the constant-density k-epsilon turbulence model provides a satisfactory representation of the aerodynamics in most practical combustor flows. The exception is the case of jet-stabilized combustor flow, due to the fact that the k-epsilon model cannot replicate the highly dissipative phenomenon found in such flows.

Nikjooy, M.↗

Vaporization and combustion of fuel droplets at supercritical conditions

Vaporization and combustion liquid-fuel droplets in both sub- and super-critical environments have been examined. The formulation is based on the complete conservation equations for both gas and liquid phases, and accommodates finite-rate chemical kinetics and a full treatment of liquid-vapor phase equilibrium at the droplet surface. The governing equations and the associated interface boundary conditions are solved numerically using a fully coupled, implicit scheme with the dual time-stepping integration technique. The model is capable of treating the entire droplet history, including the transition from the subcritical to the supercritical state. As a specific example, the combustion of n-pentane fuel droplets in air is studied for pressures of 5-140 atm. In addition, the dynamic responses of droplet vaporization and combustion to ambient-pressure oscillations are investigated. Results indicate that the droplet gasification and burning mechanisms depend greatly on the ambient pressure. In particular, a rapid enlargement of the vaporization and combustion responses occurs when the droplet surface reaches its critical point, mainly due to the strong variations of latent heat of vaporization and thermophysical properties at the critical state.

Yang, Vigor↗

Nonlinear Modeling and Control of a Propellant Mixer

A mixing chamber used in rocket engine combustion testing at NASA Stennis Space Center is modeled by a second order nonlinear MIMO system. The mixer is used to condition the thermodynamic properties of cryogenic liquid propellant by controlled injection of the same substance in the gaseous phase. The three inputs of the mixer are the positions of the valves regulating the liquid and gas flows at the inlets, and the position of the exit valve regulating the flow of conditioned propellant. The outputs to be tracked and/or regulated are mixer internal pressure, exit mass flow, and exit temperature. The outputs must conform to test specifications dictated by the type of rocket engine or component being tested downstream of the mixer. Feedback linearization is used to achieve tracking and regulation of the outputs. It is shown that the system is minimum-phase provided certain conditions on the parameters are satisfied. The conditions are shown to have physical interpretation.

Barbieri, Enrique↗

Microgravity Superagglomerates Produced By Silane And Acetylene

The size of the agglomerates produced in the upper portion of a flame is important for a variety of applications. Soot particle size and density effect the amount of radiative heat transfer from a fire to its surroundings. Particle size determines the lifetime of smoke in a building or in the atmosphere, and exposure hazard for smoke inhaled and deposited in the lungs. The visibility through a smoke layer and dectectability of the smoke are also greatly affected by agglomerate size. Currently there is limited understanding of soot growth with an overall dimension of 10 m and larger. In the case of polystyrene, smoke agglomerates in excess of 1 mm have been observed raining out from large fires. Unlike hydrocarbon fuels, silane has the advantage that silica particles are the major combustion product resulting in a particle volume fraction a factor of ten greater than that for a carbonaceous smoke. There are two very desirable properties of silica aero-gels that are important for both space and earth based applications. The first important property is its inertness to most oxidizing and reducing atmospheres. Therefore, silica aero-gels make excellent fire ablatives and can be used in very demanding applications. The second important property is that silica aero-gels are expected to have very high porosity (greater than 0.999), making them lightweight and ideal for aerospace applications. The added benefit of the high porosity is that they can be used as extremely efficient filters for many earth based applications as well. Evidence of the formation of superagglomerates in a laminar acetylene/air diffusion flame was found by Sorensen et al. [1]. An interconnecting web of super-agglomerates was observed to span the width of the soot plume in the region just above the flame tip and described as a gel state. It was observed that this gel state immediately breaks up into agglomerates as larges as 100 m due to buoyancy induced turbulence. Large soot agglomerates were observed in microgravity butane jet diffusion flames by Ito et al.[2]. Several other works to date have studied the effect of flame structure on soot volume fraction and agglomeration size in a microgravity environment.[3-4]. In microgravity the absence of buoyant convective flows increases the residence time in the flame and causes a broadening of the high temperature region in the flame. Both of these factors play a significant role in gas phase radiation and soot formation

Gokoglu, Suleyman↗

Combustion Module 1: Spacelab Racks Integrated at the Lewis Research Center for the First Time

The Combustion Module-1 (CM-1), NASA's largest (over 1800 lb) and one of the most sophisticated combustion experiments ever to fly on the Spacelab, will be carried on the first Microgravity Science Laboratory (MSL-1) mission aboard the space shuttle flight STS-84 in April 1997. The CM-1 project is a stepping stone to the space station era, because the hardware can support multiple investigators on the same mission and can be integrated at user locations and shipped to the launch site. CM-1 is being developed to accommodate microgravity combustion experiments that are designed to help explain and predict the behavior of combustion processes. Although the two principal investigators for CM-1 are both studying combustion processes, their investigations are quite different. Professor Paul D. Ronney of the University of Southern California will examine the Structures of Flame Balls at Low Lewis Numbers (SOFBALL), in which a variety of fuel-lean gaseous mixtures fill the combustion chamber and are ignited. Professor Gerard M. Faeth of the University of Michigan will investigate Laminar Soot Processes (LSP) by studying the key properties of burning gas jets of fuel, employing different fuels and nozzle sizes.

Source record↗

Environmental Durability and Stress Rupture of EBC/CMCs

This research focuses on the strength and creep performance of SiC fiber-reinforced SiC ceramic matrix composite (CMC) environmental barrier coating (EBC) systems under complex simulated engine environments. Tensile-strength and stress-rupture testing was conducted to illustrate the material properties under isothermal and thermal gradient conditions. To determine material durability, further testing was conducted under exposure to thermal cycling, thermal gradients and simulated combustion environments. Emphasis is placed on experimental techniques as well as implementation of non-destructive evaluation, including modal acoustic emission and electrical resistivity monitoring, to characterize strength degradation and damage mechanisms. Currently, little is known about the behavior of EBC-CMCs under these conditions; consequently, this work will prove invaluable in the development of structural components for use in high temperature applications.

Appleby, Matthew↗