Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMBUSTION PHYSICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

Measurement of transient gas flow parameters by diode laser absorption spectroscopy

An absorption spectrometer based on diode lasers is developed for measuring two-dimension maps of temperature and water vapour concentration distributions in the combustion zones of two mixing supersonic flows of fuel and oxidiser in the single run regime. The method of measuring parameters of hot combustion zones is based on detection of transient spectra of water vapour absorption. The design of the spectrometer considerably reduces the influence of water vapour absorption along the path of a sensing laser beam outside the burning chamber. The optical scheme is developed, capable of matching measurement results in different runs of mixture burning. A new algorithm is suggested for obtaining information about the mixture temperature by constructing the correlation functions of the experimental spectrum with those simulated from databases. A two-dimensional map of temperature distribution in a test chamber is obtained for the first time under the conditions of plasma-induced combusion of the ethylene – air mixture. (laser applications and other topics in quantum electronics)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Thermally Stratified Compression Ignition: A new advanced low temperature combustion mode with load flexibility

We introduce a new advanced combustion mode, called Thermally Stratified Compression Ignition (TSCI), which uses direct water injection to control both the average temperature and the temperature distribution prior to ignition, thereby providing cycle-to-cycle control over the start and rate of heat release in Low Temperature Combustion (LTC). Experiments were conducted to fundamentally understand the effects of water injection on heat release in LTC. Our results show that water injection retards the start of combustion due to the latent heat of vaporization of the injected water. Furthermore, for start of water injection timings between 20 and 70 degrees before top dead center, combustion is significantly elongated compared to without water injection. The 10–90% burn duration with 6.6 and 9.0 mg of water per cycle was 77% and 146% longer than without water injection, respectively. Forced thermal stratification result from a direct water injection which reduces the heat release rate by local evaporative cooling. Finally, the load limits with and without water injection were determined experimentally. Without water injection, the load range was 2.3–3.6 bar gross IMEP. By using water injection to control heat release, the load range in TSCI was 2.3–8.4 bar gross IMEP, which is a range expansion of over 350%. These results demonstrate that direct water injection can provide significant improvements to both controllability and the range of operability of LTC, thereby resolving the major challenges associated with HCCI.

20 FOSSIL-FUELED POWER PLANTS↗

The autoignition of iso-cetane at high to moderate temperatures and elevated pressures: Shock tube experiments and kinetic modeling

Iso-cetane (2,2,4,4,6,8,8-heptamethylnonane, C{sub 16}H{sub 34}) is a highly branched alkane reference compound for determining cetane ratings. It is also a candidate branched alkane representative in surrogate mixtures for diesel and jet fuels. Here new experiments and kinetic modeling results are presented for the autoignition of iso-cetane at elevated temperatures and pressures relevant to combustion in internal combustion engines. Ignition delay time measurements were made in reflected shock experiments in a heated shock tube for {phi} = 0.5, 1.0, and 1.5 iso-cetane/air mixtures at temperatures ranging from 879 to 1347 K and pressures from 8 to 47 atm. Ignition delay times were measured using electronically excited OH emission, monitored through the shock tube end wall, and piezoelectric pressure transducer measurements, made at side wall locations. A new kinetic mechanism for the description of the oxidation of iso-cetane is presented that is developed based on a previous mechanism for iso-octane. Computed results from the mechanism are found in good agreement with the experimental measurements. To our knowledge, the ignition time measurements for iso-cetane presented here are the first of their kind. (author)

33 ADVANCED PROPULSION SYSTEMS↗

Fluorescence properties of Tb{sup 3+} and Sm{sup 3+} activated novel LiAl{sub 7}B{sub 4}O{sub 17} host via solution combustion synthesis

Graphical abstract: - Highlights: • New LiAl{sub 7}B{sub 4}O{sub 17}:Tb{sup 3+}, Sm{sup 3+} phosphors were synthesized first time by solution combustion method. • The LiAl{sub 7}B{sub 4}O{sub 17}:Tb{sup 3+} emissions; 489, 544, 586 and 623 nm (λ{sub ex} = 234 nm). • Also for LiAl{sub 7}B{sub 4}O{sub 17}:Sm{sup 3+}; 564, 601 and 649 nm (λ{sub ex} = 403 nm). • Synthesized materials were characterized by powder XRD, FE-SEM. • Concentration quenching mechanism and critical transfer distance of Tb{sup 3+} and Sm{sup 3+} in the prepared sample has been investigated. - Abstract: Novel LiAl{sub 7}B{sub 4}O{sub 17} (LABO) phosphor activated with trivalent rare earth ions (RE = Tb, Sm) was synthesized by using solution combustion synthesis. The powder X-ray diffraction (XRD), field emission-scanning electron microscope (FE-SEM), photoluminescence (PL), critical transfer distance (R{sub c}) and quenching mechanism studies were employed to characterize the samples. Under ultraviolet irradiation of the LiAl{sub 7}B{sub 4}O{sub 17}: Tb{sup 3+}, Sm{sup 3+} phosphors exhibit the typical green ({sup 5}D{sub 4} → {sup 7}F{sub j} = 6, 5, 4 and 3) emission band of the Tb{sup 3+} ions, as well as an orange-red and red ({sup 4}G{sub 5/2} → {sup 6}H{sub J=5/2,} {sub 7/2,} {sub 9/2}) emission bands of the Sm{sup 3+} ions. These results suggest that Tb{sup 3+} and Sm{sup 3+} activated LABO phosphor could be promising in vision of the necessity for solid state lighting applications.

36 MATERIALS SCIENCE↗

Dependence of catalytic properties of Al/Fe{sub 2}O{sub 3} thermites on morphology of Fe{sub 2}O{sub 3} particles in combustion reactions

Three Fe{sub 2}O{sub 3} particle samples with the same crystal structure but different morphologies were prepared by the hydrothermal method and then combined with Al nanoparticles to produce Al/Fe{sub 2}O{sub 3} thermites using ultrasonic mixing. The properties of Fe{sub 2}O{sub 3} and Al/Fe{sub 2}O{sub 3} were studied using a combination of experimental techniques including scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and differential scanning calorimetry (DSC). The influences of the three Al/Fe{sub 2}O{sub 3} thermites on the combustion properties of the AP/HTPB (ammonium perchlorate/hydroxyl-terminated polybutadiene) composite propellant were investigated in comparison to those of Fe{sub 2}O{sub 3}. The results show that the Al/Fe{sub 2}O{sub 3} thermites are better than Fe{sub 2}O{sub 3} in enhancing the combustion performance of AP/HTPB. Furthermore, the surface area, which depends on size and mophology, of Fe{sub 2}O{sub 3} particles was found to play a vital role in improving the burning rate of the thermites-containing propellant formulation, with the smallest particles with the largest surface-to-volume (S/V) ratio performing the best. The enhanced catalytic property of the granular-shape Fe{sub 2}O{sub 3} and the corresponding thermite is attributed to the large specific surface area of Fe{sub 2}O{sub 3}. The different thermal behaviors of these three superthemites were supposed to be attributed to the surface site of Fe{sub 2}O{sub 3} particles. This work provides a better understanding on the catalytic properties of thermites that are important for combustion applications. - Graphical abstract: Effects of Fe{sub 2}O{sub 3} and Al/Fe{sub 2}O{sub 3} have been compared for the first time by analyzing combustion properties of formulations containing them, suggesting their potential application in AP/HTPB composite propellant systems. - Highlights: • Three Fe{sub 2}O{sub 3} particles with different morphologies (polyhedral, oval and granular) were prepared by the hydrothermal method. • Thermal behaviors of thermites Al/Fe{sub 2}O{sub 3} are studied upon DSC data. • Effects of Fe{sub 2}O{sub 3} and Al/Fe{sub 2}O{sub 3} on the combustion properties of the AP/HTPB composite propellant are first investigated.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of spatial nonuniformity of heating on compression and burning of a thermonuclear target under direct multibeam irradiation by a megajoule laser pulse

Direct-drive fusion targets are considered at present as an alternative to targets of indirect compression at a laser energy level of about 2 MJ. In this approach, the symmetry of compression and ignition of thermonuclear fuel play the major role. We report on the results of theoretical investigation of compression and burning of spherical direct-drive targets in the conditions of spatial nonuniformity of heating associated with a shift of the target from the beam center of focusing and possible laser radiation energy disbalance in the beams. The investigation involves numerous calculations based on a complex of 1D and 2D codes RAPID, SEND (for determining the target illumination and the dynamics of absorption), DIANA, and NUT (1D and multidimensional hydrodynamics of compression and burning of targets). The target under investigation had the form of a two-layer shell (ablator made of inertial material CH and DT ice) filled with DT gas. We have determined the range of admissible variation of compression and combustion parameters of the target depending on the variation of the spatial nonuniformity of its heating by a multibeam laser system. It has been shown that low-mode (long-wavelength) perturbations deteriorate the characteristics of the central region due to less effective conversion of the kinetic energy of the target shell into the internal energy of the center. Local initiation of burning is also observed in off-center regions of the target in the case of substantial asymmetry of irradiation. In this case, burning is not spread over the entire volume of the DT fuel as a rule, which considerably reduces the thermonuclear yield as compared to that in the case of spherical symmetry and central ignition.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

An experimental and kinetic modeling study of n-butanol combustion

n-Butanol is a fuel that has been proposed as an alternative to conventional gasoline and diesel fuels. In order to better understand the combustion characteristics of n-butanol, this study presents new experimental data for n-butanol in three experimental configurations. Species concentration profiles are presented in jet stirred reactor (JSR) at atmospheric conditions and a range of equivalence ratios. The laminar flame speed obtained in an n-butanol premixed laminar flame is also provided. In addition, species concentration profiles for n-butanol and n-butane in an opposed-flow diffusion flame are presented. The oxidation of n-butanol in the aforementioned experimental configurations has been modeled using an improved detailed chemical kinetic mechanism (878 reactions involving 118 species) derived from a previously proposed scheme in the literature. The proposed mechanism shows good qualitative agreement with the various experimental data. Sensitivity analyses and reaction path analyses have been conducted to interpret the results from the JSR and opposed-flow diffusion flame. It is shown that the main reaction pathway in both configurations is via H-atom abstraction from the fuel followed by {beta}-scission of the resulting fuel radicals. Several unimolecular decomposition reactions are important as well. This study gives a better understanding of n-butanol combustion and the product species distribution. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Soot inception limits in laminar diffusion flames with application to oxy-fuel combustion

For diffusion flames, the combination of oxygen enrichment and fuel dilution results in an increase in the stoichiometric mixture fraction, Z{sub st}, and alters the flame structure, i.e., the relationship between the local temperature and the local gas composition. Increasing Z{sub st} has been shown to result in the reduction or even elimination of soot. In the present work, the effects of variable Z{sub st} on soot inception are investigated in normal and inverse coflow flames, using ethylene as the fuel. Use of the inverse coflow flame underscores the validity of these concepts, since the convective field in the inverse flame directs particles into the fuel-rich region. Sooting limits based on particle luminosity are measured as a function of Z{sub st}. The sooting limit is obtained by varying the amount of inert gas until soot appears above a predefined height. For each limit flame, the adiabatic flame temperature is calculated and the flame temperature at the half-height is measured. The flame temperature at the sooting limit is found to increase with Z{sub st} for both normal and inverse flames. The effects of residence time are also investigated, and the sooting limit inception temperature is found to be dependent on fuel stream velocity for both the normal and inverse configurations. A simple model applicable to oxy-fuel combustion is presented which describes how increasing Z{sub st} results in the reduction and ultimately elimination of soot. This model assumes that soot inception can only occur in a region where critical values for species, temperature, and residence time are met. The soot inception region is shown to be bounded by two isotherms: a low-temperature boundary that is a function of residence time, and a high-temperature boundary that corresponds to the location of a critical local carbon-to-oxygen ratio. The effect of increasing Z{sub st} is to move the boundaries of the soot inception zone towards each other, until the zone is infinitely thin and thus the sooting limit is reached. By comparing the model to experimental data, a critical local C/O ratio of 0.53 and a sooting limit inception temperature of 1640 K (for a characteristic residence time of 22 ms) were determined for ethylene. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Response analysis of a laminar premixed M-flame to flow perturbations using a linearized compressible Navier-Stokes solver

The response of a laminar premixed methane-air flame subjected to flow perturbations around a steady state is examined experimentally and using a linearized compressible Navier-Stokes solver with a one-step chemistry mechanism to describe combustion. The unperturbed flame takes an M-shape stabilized both by a central bluff body and by the external rim of a cylindrical nozzle. This base flow is computed by a nonlinear direct simulation of the steady reacting flow, and the flame topology is shown to qualitatively correspond to experiments conducted under comparable conditions. The flame is then subjected to acoustic disturbances produced at different locations in the numerical domain, and its response is examined using the linearized solver. This linear numerical model then allows the componentwise investigation of the effects of flow disturbances on unsteady combustion and the feedback from the flame on the unsteady flow field. It is shown that a wrinkled reaction layer produces hydrodynamic disturbances in the fresh reactant flow field that superimpose on the acoustic field. This phenomenon, observed in several experiments, is fully interpreted here. The additional perturbations convected by the mean flow stem from the feedback of the perturbed flame sheet dynamics onto the flow field by a mechanism similar to that of a perturbed vortex sheet. The different regimes where this mechanism prevails are investigated by examining the phase and group velocities of flow disturbances along an axis oriented along the main direction of the flow in the fresh reactant flow field. It is shown that this mechanism dominates the low-frequency response of the wrinkled shape taken by the flame and, in particular, that it fully determines the dynamics of the flame tip from where the bulk of noise is radiated.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Measurements of combustion properties in a microwave enhanced flame

Microwave induced flame speed enhancement is quantified in a laminar, premixed CH{sub 4}/air wall stagnation flat flame. Experiments were performed in a high Q microwave cavity with the cavity tuned so that the maximum microwave field is located in the vicinity of a flat flame front. Equivalence ratios were varied between 0.6 and 0.8. When the flame is radiated by a continuous wave microwave field of approximately 5 kV/cm, the flame front is observed to move towards the burner exit and stabilize at a standoff distance corresponding to a flame speed increase of up to 20%. No microwave discharge is observed, indicating that the enhanced flame speed arises from microwave energy deposited directly into the reaction zone through coupling to the weakly ionized gas in that region. Laser diagnostics were performed to quantify temperature increase, the laminar flame speed enhancement, and changes in the OH radical concentration through filtered Rayleigh scattering, particle image velocimetry, and planar laser induced fluorescence, respectively. These measurements indicate that microwave radiation may prove to be an effective means to non-invasively control and enhance flame stability in combustors. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

An experimental and kinetic modeling study of n-propanol and iso-propanol combustion

A kinetic model is developed to describe combustion of n-propanol and iso-propanol. It is validated by comparing predictions made using this kinetic model with new experimental data on structures of counterflow non-premixed flames and previously reported data over a wide range of configurations and conditions. The elementary pyrolysis reactions of methanol and ethanol are well-known and were used as a starting point for extension to propanol. A detailed description leading to evaluation of rate constants for initiation reactions, metathesis reactions, decomposition reactions, and four-center molecular dehydration reactions are given. Decomposition and oxidation of primary intermediate products are described using a previously developed semi-detailed kinetic model for hydrocarbon fuels. The kinetic mechanism is made up of more than 7000 reactions among 300 species. The structures of counterflow non-premixed flames were measured by removing gas samples from the flame and analyzing the samples using a gas chromatograph. The flame structures were measured under similar conditions for both fuels to elucidate the similarities and differences in combustion characteristics of the two isomers. The profiles measured include those of formaldehyde, acetaldehyde, propanal, and acetone. These species are considered to be pollutants. Validation of the kinetic model was first performed by comparing predictions with experimental data reported in the literature obtained in flow reactors and shock tubes. In these configurations, combustion is not influenced by molecular transport. The agreement between the kinetic model and experimental data was satisfactory. The predictions of the kinetic model were then compared with new and previously reported experimental data on structures of counterflow non-premixed flames of both isomers. The agreement between the kinetic model and experimental data was again satisfactory. Satisfactory agreement was also obtained when the predictions of the kinetic model were compared with experimental data obtained on low pressure burner stabilized premixed flames. The kinetic model was thus validated over a wide range of temperatures (from 900 K to 2000 K), and configurations. In general the structures and overall combustion characteristics of n-propanol flames and iso-propanol flames are similar. Acetone is formed under all conditions in iso-propanol flames, while propanal is formed in n-propanol flames. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Study of the H + O + M reaction forming OH{sup *}: Kinetics of OH{sup *} chemiluminescence in hydrogen combustion systems

The temporal variation of OH{sup *} (A{sup 2}{sigma}{sup +}) chemiluminescence in hydrogen oxidation chemistry has been studied in a shock tube behind reflected shock waves at temperatures of 1400-3300 K and at a pressure of 1 bar. The aim of the present work is to obtain a validated reaction scheme to describe OH{sup *} formation in the H{sub 2}/O{sub 2} system. Temporal OH{sup *} emission profiles and ignition delay times for lean and stoichiometric H{sub 2}/O{sub 2} mixtures diluted in 97-98% argon were obtained from the shock-tube experiments. Based on a literature review for the hydrogen combustion system, the key reaction considered was H + O + M = OH{sup *} + M. The temperature dependence of the measured peak OH{sup *} emission from the shock tube and the peak OH{sup *} concentration from a homogeneous closed reactor model are compared. Based on these results a reaction rate coefficient of k{sub 1} = (1.5 {+-} 0.4) x 10{sup 13} exp(-25 kJ mol{sup -1}/RT) cm{sup 6} mol{sup -2} s{sup -1} was found for the forward reaction which is slightly higher than the rate coefficient suggested by Hidaka et al. (1982). The comparison of measured and simulated absolute concentrations shows good agreement. Additionally, a one-dimensional laminar premixed low-pressure flame calculation was performed for where absolute OH{sup *} concentration measurements have been reported by Smith et al. (2005). The absolute peak OH{sup *} concentration is fairly well reproduced if the above mentioned rate coefficient is used in the simulation. (author)

08 HYDROGEN↗

In-Situ Species Concentration Measurements In Ammonia-Mix Flames Using Ftir Spectroscopy

Hydrogen and ammonia represent two carbon-free fuel sources that could be used in place of current fossil energy sources in combustion systems. To develop optimized ammonia combustion systems, validated modeling tools are needed. In the open literature, it has been shown that the complex chemistry associated with fuel-bound nitrogen contained in ammonia differs greatly from natural gas or hydrogen combustion. As a result, several new chemical kinetic mechanisms have been developed. Many of these mechanisms have been validated experimentally, however this has primarily focused on bulk parameters such as laminar flame speed and ignition delay time. Critically, high quality measurements of species concentrations are needed under controlled conditions which are easily represented by simple models. In this paper, direct, in-situ measurements of species concentrations and gas temperature are performed in a laminar flat-flame burner. This arrangement enables comparison with 1D model predictions, better isolating chemical kinetics from the fluid dynamics. Quantitative species concentrations are determined by absorption spectroscopy using an FTIR spectrometer. Fuel compositions representative of cracked ammonia (NH 3 /H 2 ) and ammonia-natural gas (NH 3 /CH 4 ) are considered for rich and lean equivalence ratios. A major focus of the paper is on the selection of spectral features for nitric oxide and ammonia and correcting for large amounts of baseline H 2 O absorption.

36 MATERIALS SCIENCE↗

Synthesis and catalytic properties of microemulsion-derived cerium oxide nanoparticles

The synthesis of cerium dioxide nanoparticles using an inverse microemulsion technique and precipitation method was investigated. Cerium hydroxide nanoparticles were synthesized by adding diluted ammonia to n-heptane-surfactant-cerium nitrate system. The micelle and particle size in the range of 5-12 nm were controlled by varying the molar water to surfactant ratio and analyzed by dynamic light scattering (DLS), small angle X-ray scattering (SAXS) and high-resolution transmission electron microscopy (HRTEM). Cerium hydroxide nanoparticles were isolated and subsequently treated at 100-600 deg. C to obtain nanoscale ceria. Crystallite sizes of cerium dioxide in the range of 6-16 nm were estimated by Scherrer analysis by X-ray diffraction (XRD) and HRTEM. The catalytic activity of particles annealed at 400 and 600 deg. C in soot combustion reactions was characterized by temperature-programmed oxidation (TPO) indicating a size-dependant activity. Crystallite sizes and catalytic stability of elevated ceria systems were tested in second combustion cycles. - Graphical abstract: The synthesis of cerium dioxide nanoparticles using an inverse microemulsion technique and precipitation method was investigated using small angle X-ray scattering, dynamic light scattering and high-resolution transmission electron microscopy. Catalytic activity of ceria nanoparticles was tested in soot combustion reaction indicating size-dependent reactivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Grid resolution requirement of chemical explosive mode analysis for large eddy simulations of premixed turbulent combustion

Full Article Figures & data References Citations Metrics Reprints & Permissions Read this article Abstract The grid resolution requirement for trustworthy Chemical Explosive Mode Analysis (CEMA) in Large Eddy Simulation (LES) of premixed turbulent combustion is proposed. Explicit filtering, to emulate the effect of the LES filter, is applied to one-dimensional laminar flame and three-dimensional planar turbulent flames across a wide range of Karlovitz numbers (5 - 239). The identification of the flame front by CEMA is found relatively insensitive to the cell size (Δ), while the combustion mode identification shows more significant sensitivity. Specifically, increasing Δ falsely enhances the auto-ignition and local extinction modes and suppresses the diffusion-assisted mode. Limited dependence of the CEMA performance on the turbulent combustion regime (Karlovitz number) is observed. A simple grid size criterion for reliable CEMA mode identification in LES is proposed as Δ ≲ δ L /2; The criterion can be relaxed to Δ ≲ δ L in the laminar flame limit. Furthermore, theoretical analysis is conducted on an idealised chemistry-diffusion system. The effects of the filtering process and turbulence on the local combustion mode are demonstrated, which is consistent with the numerical observations. Further, by incorporating turbulent combustion models in CEMA, potential improvement in identifying local combustion modes can be expected.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Large eddy simulation of forced ignition of an annular bluff-body burner

The optimization of the ignition process is a crucial issue in the design of many combustion systems. Large eddy simulation (LES) of a conical shaped bluff-body turbulent nonpremixed burner has been performed to study the impact of spark location on ignition success. This burner was experimentally investigated by Ahmed et al. [Combust. Flame 151 (2007) 366-385]. The present work focuses on the case without swirl, for which detailed measurements are available. First, cold-flow measurements of velocities and mixture fractions are compared with their LES counterparts, to assess the prediction capabilities of simulations in terms of flow and turbulent mixing. Time histories of velocities and mixture fractions are recorded at selected spots, to probe the resolved probability density function (pdf) of flow variables, in an attempt to reproduce, from the knowledge of LES-resolved instantaneous flow conditions, the experimentally observed reasons for success or failure of spark ignition. A flammability map is also constructed from the resolved mixture fraction pdf and compared with its experimental counterpart. LES of forced ignition is then performed using flamelet fully detailed tabulated chemistry combined with presumed pdfs. Various scenarios of flame kernel development are analyzed and correlated with typical flow conditions observed in this burner. The correlations between, velocities and mixture fraction values at the sparking time and the success or failure of ignition, are then further discussed and analyzed. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Chemical Imaging and Dynamical Studies of Reactivity and Emergent Behavior in Complex Interfacial Systems. Final Technical Report

This research program explored the efficacy of using molecular-level manipulation, imaging and scanning tunneling spectroscopy in conjunction with supersonic molecular beam gas-surface scattering to significantly enhance our understanding of chemical processes occurring on well-characterized interfaces. One program focus was on the spatially-resolved emergent behavior of complex reaction systems as a function of the local geometry and density of adsorbate-substrate systems under reaction conditions. Another focus was on elucidating the emergent electronic and related reactivity characteristics of intentionally constructed single and multicomponent atom- and nanoparticle-based materials. We also examined emergent chirality and self-organization in adsorbed molecular systems where collective interactions between adsorbates and the supporting interface lead to spatial symmetry breaking. In many of these studies we combined the advantages of scanning tunneling (STM) and atomic force (AFM) imaging, scanning tunneling local electronic spectroscopy (STS), and reactive supersonic molecular beams to elucidate precise details of interfacial reactivity that had not been observed by more traditional surface science methods. Using these methods, it was possible to examine, for example, the differential reactivity of molecules adsorbed at different bonding sites in conjunction with how reactivity is modified by the local configuration of nearby adsorbates. At the core of this effort was the goal of significantly extending our understanding of interfacial atomic-scale interactions to create, with intent, molecular assemblies and materials with advanced chemical and physical properties. This ambitious program addressed several key topics in DOE Grand Challenge Science, including emergent chemical and physical properties in condensed phase systems, novel uses of chemical imaging, and the development of advanced reactivity concepts in combustion and catalysis including carbon management. These activities directly benefitted national science objectives in the areas of chemical energy production and advanced materials development.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗