Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Behavior analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

Martian B Storm Genesis and Evolution: Initial Analysis of Thermal Datasets.

Introduction: Dust lifting on Mars likely occurs primarily as a result of the exchange of momentum between the atmosphere and the surface via saltation. During saltation, sand-sized particles are mobilized but do not enter into suspension. When these larger particles fall back to the surface, kinetic energy is transferred to smaller dust particles which are then lofted into suspension in the atmosphere. Depending on the altitude to which dust is lofted, it can have a significant effect on atmospheric temperatures. As a strong absorber and emitter in the infrared, dust can influence atmospheric heating and modify the global circulation and weather on Mars [1,2]. Although dust is present in Mars’ atmosphere throughout the year, the atmosphere is generally dustier during the second half of the year when Mars is near perihelion. Observations reveal that episodic global-scale dust storms and fairly regular regional-scale dust storms are superimposed on a well-defined and highly repeatable seasonal cycle of dust opacity and associated mid-level atmospheric temperature responses. Kass et al. (2016) used 50 Pa temperature observations from MRO/MCS to identify three highly repeatable time periods during which regional dust storms occur, and designated them the “A”, “B” and “C” storms. While “A” and “C” storms have been studied a fair amount to-date, “B” storms have not yet been investigated in detail. This study explores the generation and evolution of the annually recurring regional dust storm known as the “B” storm, which was identified and categorized by Kass et al. (2016) based on 25 km (50 Pa) temperature observations. The B storm is a southern-hemisphere (SH) phenomenon that originates at the cap edge just after perihelion and which reaches peak intensity during the SH summer solstice, Ls 270. It may originate from the cap edge storms that spawn near the edge of the seasonal CO2 cap during retreat, but the mechanisms for B storm genesis have yet to be determined definitively [1]. Methods: We will use observational data sets and a global climate model (GCM) to investigate “B” regional storms. The data analysis component will include the analysis of imagery from MGS/MOC and MRO/MARCI, and spectroscopic data sets of dust and temperatures from MGS/TES and MRO/MCS with the goal of fully characterizing the behavior of these storms. Both MGS and TES provide data well-suited for temperature analysis at 25 km. MCS measures atmospheric temperature, dust extinction, and water ice extinction at 5 km intervals from the surface to about 80 km. TES measured atmospheric temperatures, column dust and water ice opacities, and column water vapor abundances. Measurements made by TES extended from the surface to about 40 km [1]. At the 50 Pa (25 km) level, local dust events usually confined to shallower depths are effectively filtered out of the analysis leaving the regional dust events identifiable by their temperature signatures [1]. Our preliminary analysis makes use of the fact that the brightness temperature at 15 microns (T15 temperature) is a close approximation to observed temperature at 25 km. We first reproduce the zonal mean 50 Pa level temperature plots for MY 29-32 to establish a baseline for our procedures moving forward [1]. Expanding on Kass et al. (2016), we include recent MCS data from MY 33 and 34 as well. Preliminary Analysis: The daytime (3PM) T15 temperatures in Figure 1 indicate: in MY 29, a strong A storm at Ls 240, a B storm at high southern latitudes just after Ls 270, and a C storm at Ls 320; in MY 30, a B storm at Ls 270; in MY 31 & MY 32, a B storm just before Ls 270; in MY 33, a B storm at Ls 270; and in MY 34, a strong A storm in the northern hemisphere at Ls 210, and a B storm around Ls 270 although there is a data gap. For the B storms, each is indicative of lofted dust and resultant warming. The daytime temperature structure illustrates that the B storm occurs annually around Ls 270 and is confined to high southern latitudes. It reaches its peak intensity around SH summer solstice, Ls 270, consistently for all six MY assessed. Since direct solar heating is absent overnight, the nighttime T15 temperatures (Figure 2) are often useful for differentiating the heat signature of direct solar heating from the dynamical response to that heating. However, in the southern polar latitudes at perihelion the sun does not set and direct solar heating remains present throughout the night. Importantly for our study, dust lofted in the B storm experiences this direct heating day and night for the entirety of its lifetime. The B storm expands as far north as -60 latitude and decays in latitudinal extent more gradually than it grows. This feature is less obvious in the nighttime (3AM) T15 temperatures (Figure 2). The temperature signal is stronger at night for MY 30-33. The warm pool is larger in area relative to the background at night in these four cases. This more uniform warming masks the “tail” feature somewhat, such that it is barely noticeable during these years. Unfortunately, gaps in MCS data in MY 29 and 34 prevent confirmation of the tail feature during those years, however, the B storm temperature signature follows a very different pattern than that described for MY 30-33. MY 29 and 34 appear to show smaller centers of warming at night and larger centers of warming during the day. This is in opposition to that previously described for MY 30-33. Conclusions and Future Work: We will continue investigating the heat signatures of B storms by looking at the total column heating as recorded by TES. We will also look at lower altitudes for patterns that may describe the relationship between B storms and the cap edge storms that develop while the seasonal cap is retreating. In the future, we will use GCM simulations to determine the atmospheric and thermo-dynamic conditions associated with these storms.

Courtney Marylou Batterson↗

Discrete event simulation tool for analysis of qualitative models of continuous processing systems

An artificial intelligence design and qualitative modeling tool is disclosed for creating computer models and simulating continuous activities, functions, and/or behavior using developed discrete event techniques. Conveniently, the tool is organized in four modules: library design module, model construction module, simulation module, and experimentation and analysis. The library design module supports the building of library knowledge including component classes and elements pertinent to a particular domain of continuous activities, functions, and behavior being modeled. The continuous behavior is defined discretely with respect to invocation statements, effect statements, and time delays. The functionality of the components is defined in terms of variable cluster instances, independent processes, and modes, further defined in terms of mode transition processes and mode dependent processes. Model construction utilizes the hierarchy of libraries and connects them with appropriate relations. The simulation executes a specialized initialization routine and executes events in a manner that includes selective inherency of characteristics through a time and event schema until the event queue in the simulator is emptied. The experimentation and analysis module supports analysis through the generation of appropriate log files and graphics developments and includes the ability of log file comparisons.

Malin, Jane T.↗

Dynamic analysis of nonlinear rotor-housing systems

Nonlinear analysis methods are developed which will enable the reliable prediction of the dynamic behavior of the space shuttle main engine (SSME) turbopumps in the presence of bearing clearances and other local nonlinearities. A computationally efficient convolution method, based on discretized Duhamel and transition matrix integral formulations, is developed for the transient analysis. In the formulation, the coupling forces due to the nonlinearities are treated as external forces acting on the coupled subsystems. Iteration is utilized to determine their magnitudes at each time increment. The method is applied to a nonlinear generic model of the high pressure oxygen turbopump (HPOTP). As compared to the fourth order Runge-Kutta numerical integration methods, the convolution approach proved to be more accurate and more highly efficient. For determining the nonlinear, steady-state periodic responses, an incremental harmonic balance method was also developed. The method was successfully used to determine dominantly harmonic and subharmonic responses fo the HPOTP generic model with bearing clearances. A reduction method similar to the impedance formulation utilized with linear systems is used to reduce the housing-rotor models to their coordinates at the bearing clearances. Recommendations are included for further development of the method, for extending the analysis to aperiodic and chaotic regimes and for conducting critical parameteric studies of the nonlinear response of the current SSME turbopumps.

Noah, Sherif T.↗

Snap-Through Instability Patterns in Truss Structures

Geometrically nonlinear truss structures with snap-through behavior are demonstrated by using an arc length approach within a finite element analysis. The instability patterns are equilibrium paths that are plotted throughout the snap-through event. Careful observation of these patterns helps to identify weak designs in large space structures, as well as identify desirable snap-through behavior in the miniaturization of electronic devices known as microelectromechanical systems (MEMS). Examples of highly nonlinear trusses that show snap-through behavior are examined by tracing their equilibrium paths.

Hrinda, Glenn A.↗

Advanced Diagnostic and Prognostic Testbed (ADAPT) Testability Analysis Report

As system designs become more complex, determining the best locations to add sensors and test points for the purpose of testing and monitoring these designs becomes more difficult. Not only must the designer take into consideration all real and potential faults of the system, he or she must also find efficient ways of detecting and isolating those faults. Because sensors and cabling take up valuable space and weight on a system, and given constraints on bandwidth and power, it is even more difficult to add sensors into these complex designs after the design has been completed. As a result, a number of software tools have been developed to assist the system designer in proper placement of these sensors during the system design phase of a project. One of the key functions provided by many of these software programs is a testability analysis of the system essentially an evaluation of how observable the system behavior is using available tests. During the design phase, testability metrics can help guide the designer in improving the inherent testability of the design. This may include adding, removing, or modifying tests; breaking up feedback loops, or changing the system to reduce fault propagation. Given a set of test requirements, the analysis can also help to verify that the system will meet those requirements. Of course, a testability analysis requires that a software model of the physical system is available. For the analysis to be most effective in guiding system design, this model should ideally be constructed in parallel with these efforts. The purpose of this paper is to present the final testability results of the Advanced Diagnostic and Prognostic Testbed (ADAPT) after the system model was completed. The tool chosen to build the model and to perform the testability analysis with is the Testability Engineering and Maintenance System Designer (TEAMS-Designer). The TEAMS toolset is intended to be a solution to span all phases of the system, from design and development through health management and maintenance. TEAMS-Designer is the model-building and testability analysis software in that suite.

Ossenfort, John↗

Multiple steady states for characteristic initial value problems

The time dependent, isentropic, quasi-one-dimensional equations of gas dynamics and other model equations are considered under the constraint of characteristic boundary conditions. Analysis of the time evolution shows how different initial data may lead to different steady states and how seemingly anamolous behavior of the solution may be resolved. Numerical experimentation using time consistent explicit algorithms verifies the conclusions of the analysis. The use of implicit schemes with very large time steps leads to erroneous results.

Salas, M. D.↗

Solving Upwind-Biased Discretizations: Defect-Correction Iterations

This paper considers defect-correction solvers for a second order upwind-biased discretization of the 2D convection equation. The following important features are reported: (1) The asymptotic convergence rate is about 0.5 per defect-correction iteration. (2) If the operators involved in defect-correction iterations have different approximation order, then the initial convergence rates may be very slow. The number of iterations required to get into the asymptotic convergence regime might grow on fine grids as a negative power of h. In the case of a second order target operator and a first order driver operator, this number of iterations is roughly proportional to h-1/3. (3) If both the operators have the second approximation order, the defect-correction solver demonstrates the asymptotic convergence rate after three iterations at most. The same three iterations are required to converge algebraic error below the truncation error level. A novel comprehensive half-space Fourier mode analysis (which, by the way, can take into account the influence of discretized outflow boundary conditions as well) for the defect-correction method is developed. This analysis explains many phenomena observed in solving non-elliptic equations and provides a close prediction of the actual solution behavior. It predicts the convergence rate for each iteration and the asymptotic convergence rate. As a result of this analysis, a new very efficient adaptive multigrid algorithm solving the discrete problem to within a given accuracy is proposed. Numerical simulations confirm the accuracy of the analysis and the efficiency of the proposed algorithm. The results of the numerical tests are reported.

Diskin, Boris↗

Analysis of Skylab IV fluid mechanic science demonstration

Several science demonstrations performed on Skylab III and IV were concerned with the behavior of fluid drops free floating in microgravity. These demonstrations, with large liquid drops, included the oscillation, rotation, impact and coalescence, and air injection into the drops. Rayleigh's analysis of the oscillation of spherical drops of a liquid predicts accurately the effect of size and surface tension on the frequency of vibrated water globules in the Skylab demonstration. However, damping occurred much faster than predicted by Lamb's or Scriven's analyses of the damping time for spherical drops. The impact demonstrations indicated that a minimum velocity is necessary to overcome surface forces and effect a coalescence, but a precise criterion for the coalescence of liquids in low g could not be determined.

Klett, M. G.↗

Variational Methods in Sensitivity Analysis and Optimization for Aerodynamic Applications

Variational methods (VM) sensitivity analysis, which is the continuous alternative to the discrete sensitivity analysis, is employed to derive the costate (adjoint) equations, the transversality conditions, and the functional sensitivity derivatives. In the derivation of the sensitivity equations, the variational methods use the generalized calculus of variations, in which the variable boundary is considered as the design function. The converged solution of the state equations together with the converged solution of the costate equations are integrated along the domain boundary to uniquely determine the functional sensitivity derivatives with respect to the design function. The determination of the sensitivity derivatives of the performance index or functional entails the coupled solutions of the state and costate equations. As the stable and converged numerical solution of the costate equations with their boundary conditions are a priori unknown, numerical stability analysis is performed on both the state and costate equations. Thereafter, based on the amplification factors obtained by solving the generalized eigenvalue equations, the stability behavior of the costate equations is discussed and compared with the state (Euler) equations. The stability analysis of the costate equations suggests that the converged and stable solution of the costate equation is possible only if the computational domain of the costate equations is transformed to take into account the reverse flow nature of the costate equations. The application of the variational methods to aerodynamic shape optimization problems is demonstrated for internal flow problems at supersonic Mach number range. The study shows, that while maintaining the accuracy of the functional sensitivity derivatives within the reasonable range for engineering prediction purposes, the variational methods show a substantial gain in computational efficiency, i.e., computer time and memory, when compared with the finite difference sensitivity analysis.

Ibrahim, A. H.↗

Reduced-gravity two-phase flow experiments in the NASA KC-135

An adequate understanding is sought of flow and heat transfer behavior in reduced and zero gravity conditions. Microgravity thermal-hydraulic analysis capabilities were developed for application to space nuclear power systems. A series of reduced gravity two phase flow experiments using the NASA KC-135 were performed. The objective was to supply basic thermal hydraulic information that could be used in development of analytical tools for design of space power systems. The experiments are described. Two main conclusions were drawn. First, the tests demonstrate that the KC-135 is a suitable test environment for obtaining two phase flow and heat transfer data in reduced gravity conditions. Second, the behavior of two phase flow in low gravity is sufficiently different from that obtained in 1 g to warrant intensive investigation of the phenomenon if adequate analytical tools are to be developed for microgravity conditions.

Cuta, Judith M.↗

Analysis of a transport fuselage section drop test

Transport fuselage section drop tests provided useful information about the crash behavior of metal aircraft in preparation for a full-scale Boeing 720 controlled impact demonstration (CID). The fuselage sections have also provided an operational test environment for the data acquisition system designed for the CID test, and data for analysis and correlation with the DYCAST nonlinear finite-element program. The correlation of the DYCAST section model predictions was quite good for the total fuselage crushing deflection (22 to 24 inches predicted versus 24 to 26 inches measured), floor deformation, and accelerations for the floor and fuselage. The DYCAST seat and occupant model was adequate to approximate dynamic loading to the floor, but a more sophisticated model would be required for good correlation with dummy accelerations. Although a full-section model using only finite elements for the subfloor was desirable, constraints of time and computer resources limited the finite-element subfloor model to a two-frame model. Results from the two-frame model indicate that DYCAST can provide excellent correlation with experimental crash behavior of fuselage structure with a minimum of empirical force-deflection data representing structure in the analytical model.

E. L. Fasanella↗

Finite element analysis of elasto-plastic soils. Report no. 4: Finite element analysis of elasto-plastic frictional materials for application to lunar earth sciences

The behavior of finite element models employing different constitutive relations to describe the stress-strain behavior of soils is investigated. Three models, which assume small strain theory is applicable, include a nondilatant, a dilatant and a strain hardening constitutive relation. Two models are formulated using large strain theory and include a hyperbolic and a Tresca elastic perfectly plastic constitutive relation. These finite element models are used to analyze retaining walls and footings. Methods of improving the finite element solutions are investigated. For nonlinear problems better solutions can be obtained by using smaller load increment sizes and more iterations per load increment than by increasing the number of elements. Suitable methods of treating tension stresses and stresses which exceed the yield criteria are discussed.

Marr, W. A., Jr.↗

Analysis of axially grooved heat pipe condensers

In an analytical study of the thermal behavior of the condenser section of a heat pipe with axial rectangular grooves under zero-g condition, the condensation rate was determined by studying the motion of the thin liquid film on the land area between grooves. It was found that the local condensation rate depends, among other factors, on the curvature of the liquid meniscus and on the shape of the land top. Computed overall heat transfer rate compares favorably with available experimental data. The liquid meniscus variation along the heat pipe length in the condenser section was also determined.

Kamotani, Y.↗

Analysis of contact pressures attainable using indentors which are bodies of revolution

The elastic behavior of a conical indentor with a rounded tip pressed against a flat anvil has been analyzed. It is found that when the radius of contact extends beyond the rounded tip, the contact radius increases much more rapidly as the pressure increases than it does for the case of a fully spherical or parabolic tip. Consequently, the pressure achieved for a rounded conical tip for a given applied force is considerably less than for a spherical or parabolic tip.

Ruoff, A. L.↗

Behavior of Al2O3 and SiO2 with heating in a Cl2 + CO stream

Differential thermal analysis (DTA) and Thermogravimetric analysis (TGA) were used to study the chlorination of alpha-Al2O3, gamma-Al2O3 and amorphous SiO2 in a Cl + CO stream, for the preparation of AlCl3 and SiCl4. The chlorination starting temperatures were 235 deg for Al2O3 and 680 deg for SiO2. The chlorination of alpha- and gamma-Al2O3 takes place via the formation of AlOCl as an intermediate product, and its subsequent dissociation at 480 to 560 deg, according to 3AlOCl yields AlCl3 + Al2O3. The chlorination activation energies are given for the three oxides.

Shchetinin, L. K.↗

Analysis of creep and relaxation in composite laminates with holes

The time-dependent behavior of composite laminates subjected to mechanical loads is studied using linear viscoelastic theory. Three-dimensional finite elements are formulated to solve the integral equilibrium equations. Analyses of creep and stress relaxation in composites with holes are performed. Results indicate that the relaxation of interlaminar stresses depends on temperature and layups, and that the creep response of strains is affected by stress redistribution between plies.

Lin, Kuen Y.↗

Non-linear dynamic analysis of geared systems, part 2

A good understanding of the steady state dynamic behavior of a geared system is required in order to design reliable and quiet transmissions. This study focuses on a system containing a spur gear pair with backlash and periodically time-varying mesh stiffness, and rolling element bearings with clearance type non-linearities. A dynamic finite element model of the linear time-invariant (LTI) system is developed. Effects of several system parameters, such as torsional and transverse flexibilities of the shafts and prime mover/load inertias, on free and force vibration characteristics are investigated. Several reduced order LTI models are developed and validated by comparing their eigen solution with the finite element model results. Several key system parameters such as mean load and damping ratio are identified and their effects on the non-linear frequency response are evaluated quantitatively. Other fundamental issues such as the dynamic coupling between non-linear modes, dynamic interactions between component non-linearities and time-varying mesh stiffness, and the existence of subharmonic and chaotic solutions including routes to chaos have also been examined in depth.

Singh, Rajendra↗