SEARCH · Engineering Papers

Results for “Advanced Propulsion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Demonstrating autonomous controls on hardware test beds is a necessity for successful missions to Mars and beyond

NASA and the Department of Defense are planning for a mission to Mars in the 2030s–2040s using nuclear thermal propulsion (NTP). NTP uses a nuclear reactor to heat flowing hydrogen and create thrust. A serious concern for crewed and uncrewed missions to Mars is the loss of reactor control. The reactor startup and initial rocket impulse are initiated in cislunar or near-earth orbital regions; therefore, radio communications between ground control and the NTP engine should occur in real time. However, radio communications can take more than 20 min, depending on planet positions, to reach Mars orbiters from ground control. To address this delay, local autonomous controls are implemented onboard the NTP engine to ensure acceptable operation. However, autonomous controls have not been demonstrated or implemented in research or power reactor contexts because of safety and reliability concerns. To enable autonomous controls development, demonstration, and validation, Oak Ridge National Laboratory has created a nonnuclear hardware-in-the-loop test bed. Sensors throughout the test bed relay system status and hardware response to the user control algorithm, including measurements of temperature, flow, pressure of a loop, control drum position, and drum speed. This paper discusses the development of this facility and user accessibility.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2019

Synthesis of convection velocity and turbulence measurements in three-stream jets

Key flow regions linked to jet noise sources are investigated through comparison of convection velocity and turbulence measurements in high-speed three-stream nozzles. Time-resolved flow imaging using a photomultiplier tube array was applied in the Nozzle Acoustic Test Rig at NASAs Aero-Acoustic Propulsion Lab to measure 250 kHz repetition laser scattering signals arising from seeding particles at 32 points in high-speed flow. Particle image velocimetry measurements previously reported by NASA provided mean velocity and turbulence intensity. Results for convection velocity of the particle concentration field were obtained from the time-resolved data for three-stream nozzle configurations using a cross-correlation approach. The three-stream cases included an axisymmetric and an asymmetric, offset nozzle configuration. For the axisymmetric case, areas of high convection velocity and turbulence intensity were found to occur 4–6 area-equivalent nozzle diameters downstream from the nozzle exit. Comparison of convection velocity between the axisymmetric and offset cases shows this same region as having the greatest reduction in convection velocity due to the offset, up to 20% reduction for the offset case compared to the axisymmetric case. Finally, these findings suggest that this region along the centerline near the end of the potential core is an important area for noise generation with jets and contributes to the noise reductions seen from three-stream offset nozzles.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2023

Diffusion study of uranium mononitride/zirconium carbide composite for space nuclear propulsion

Here, the next generation of space exploration will require extensive developments in rocket technology. Space nuclear propulsion is of interest due to its high fuel density and power, however, it also has high temperature and stability demands. This study examines a uranium nitride/zirconium carbide ceramic-ceramic particle composite as a potential fuel for these missions. Based on the constituent properties, this fuel composite is expected to be highly thermally efficient and resistant to the hot hydrogen propellant. One of the main concerns with this composite is unknown diffusion behavior between UN and ZrC over time. Diffusion couples and composites were used to determine how these constituents will behave when left in contact at high temperatures. UN and ZrC were found to have limited but observable diffusion at the phase boundary. The resulting phase is a UZr(CN) quaternary phase. UZr(CN) has been examined for other high temperature and gas nuclear reactors with preliminary success; however, there lacks sufficient data to fully qualify this phase. Based on the limited information available, the resultant quaternary phase could be deemed acceptable and even provide better adhesion for the fuel particles (UN) to the matrix (ZrC).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2014

Novel Power Electronics Three-Dimensional Heat Exchanger: Preprint

Electric drive systems for vehicle propulsion enable technologies critical to meeting challenges for energy, environmental, and economic security. Enabling cost-effective electric drive systems requires reductions in inverter power semiconductor area. As critical components of the electric drive system are made smaller, heat removal becomes an increasing challenge. In this paper, we demonstrate an integrated approach to the design of thermal management systems for power semiconductors that matches the passive thermal resistance of the packaging with the active convective cooling performance of the heat exchanger. The heat exchanger concept builds on existing semiconductor thermal management improvements described in literature and patents, which include improved bonded interface materials, direct cooling of the semiconductor packages, and double-sided cooling. The key difference in the described concept is the achievement of high heat transfer performance with less aggressive cooling techniques by optimizing the passive and active heat transfer paths. An extruded aluminum design was selected because of its lower tooling cost, higher performance, and scalability in comparison to cast aluminum. Results demonstrated a heat flux improvement of a factor of two, and a package heat density improvement over 30%, which achieved the thermal performance targets.

30 DIRECT ENERGY CONVERSION↗

DOE OSTI2025

High Power Density, Carbon Neutral Electrical Power Generation for Air Vehicles

The synergistic integration of a Solid Oxide Fuel Cell-Combustor (SOFC-C) with a turbogenerator (TG) will provide a very high fuel-to-electricity conversion efficiency while maintaining high power-to-weight ratio during high-altitude flight. The proposed SOFC-C-TG power generation technology exceeds the REEACH technical performance targets (TPT). This unique concept addresses many of the challenges faced in all electric propulsion-based aviation. The system has high part-load efficiency (more than 65% lower heating value (LHV)) during long cruise times, load following capability, high-power capacity at high altitudes adapting to low temperatures and pressures, rapid startup time of less than 30 minutes (proven with current SOFC technology), high power density (more than 3.2 kW/kg), efficient thermal management, and a foundation for a compact, efficient electrical storage and power generation system (ESPG). The SOFC-C concept achieves the technology targets by reducing the complexity of traditional fuel cell-gas turbine hybrid systems (FC-GT). The SOFC-C does not require heat exchangers and dramatically reduces the balance of plant increasing power density and performance in efficiency. The reduction in mass through elimination of heat exchangers, external reformer, and other components dramatically decreases the overall thermal dampening of the system which enables rapid startup and load following capability. Direct control of the cathode inlet temperature of the SOFC-C enables rapid warm-up of the SOFC tubes with the ability to reach operating temperature and full power in less than 30 minutes.

03 NATURAL GAS↗

DOE OSTI2021

Modelling Nuclear Thermal Propulsion Reactor Startup Transients

The National Aeronautics and Space Administration (NASA) has set the goal of a manned mission to Mars by the year 2030 [1] and charged the national academy of sci- ences "to identify primary technical and programmatic chal- lenges, merits, and risks for maturing space nuclear propulsion technologies of interest to a future human Mars exploration mission" [2]. One relevant technology, nuclear thermal propul- sion (NTP), has notable advantages over traditional chemical rockets; most important among them is the ability to produce larger specific impulse on the order of 900s. The reduction of mission time is crucial for a manned mission to Mars to reduce the risk for the crew. Due to its higher specific impulse, NTP satisfies this need and is pursued as one technology to get humans to Mars [3, 4]. The construction of an NTP sys- tem has to negotiate several challenges laid out in Ref. [2]; one of these challenges is the need to startup the NTP sys- tem from essentially cold conditions to full power within one minute. This paper focuses on studying the neutronics and thermal-hydraulics behavior of a simplified NTP model dur- ing prescribed reactivity insertions and mass flow rate (MFR) ramps. It is the goal of this paper to investigate startup, peak material temperatures, and average specific impulse for a low enriched Uranium (LEU), ceramic and metal material (CER- MET) NTP system when varying reactivity insertion and MFR ramps.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2021

Study of Hydrogen Fuel Cell Technology for Freight Rail Propulsion and Review of Relevant Industry Standards.

Alternatives to conventional diesel electric propulsion are currently of interest to rail operators. In the U.S., smaller railroads have implemented natural gas and other railroads are exploring hydrogen technology as a cleaner alternative to diesel. Diesel, battery, hydrogen fuel cell, or track electrification all have trade-offs for operations, economics, safety, and public acceptability. A framework to compare different technologies for specific applications is useful to optimize the desired results. Standards from the Association of American Railroads (AAR) and other industry best practices were reviewed for applicability with hydrogen fuel cell technology. Some technical gaps relate to the physical properties of hydrogen, such as embrittlement of metals, invisible flames, and low liquid temperatures. A reassessment of material selection, leak/flame detection, and thermal insulation methods is required. Hydrogen is less dense and diffuses more easily than natural gas, and liquid hydrogen is colder than liquefied natural gas. Different densities between natural gas and hydrogen require modifications to tank designs and flow rates. Leaked hydrogen will rise rather than pool on the ground like diesel, requiring a modification to the location of hydrogen tanks on rolling stock. Finally, the vibration and shock experienced in the rail environment is higher than light-duty vehicles and stationary applications for which current fuel cell technology has been developed, requiring a modification in tank design requirements and testing.

08 HYDROGEN↗

DOE OSTI2026

Hydrogen applications in airport operations: a review using the Port Authority of New York and New Jersey as an illustrative airport system

Airports combine aircraft propulsion, ground operations, stationary power systems, and fuel logistics in ways that make emissions reduction technically and operationally complex. Existing studies often assess hydrogen applications in these areas separately, limiting understanding of the shared infrastructure, safety, and operational constraints that shape airport deployment. This review evaluates hydrogen across three airport-relevant operational domains: aviation propulsion, ground support equipment and vehicles, and stationary power systems. Within aviation propulsion, the review examines sustainable aviation fuel production and hydrogen-powered aircraft as two distinct hydrogen-relevant pathways. The Port Authority of New York and New Jersey is used as an illustrative airport system to relate the literature to a real operating context. Drawing on peer-reviewed studies, technical reports, demonstration projects, and public operational information, the review also includes screening-level calculations of hydrogen demand and potential CO 2 e reductions for selected applications. The findings show that hydrogen's role is highly application-specific. Near-term opportunities are strongest where hydrogen serves as a low-carbon process input, supports selected high-utilization ground equipment, or contributes to resilient stationary power-system configurations. Hydrogen-powered aircraft remain a longer-term option because storage, fueling infrastructure, certification, cost, and NO x management continue to constrain deployment. Across all domains, infrastructure readiness, fuel logistics, safety requirements, and leakage management emerge as recurring determinants of viability. Future research should focus on cross-domain infrastructure planning, comparative assessment of hydrogen against alternative pathways, improved treatment of leakage and non-CO 2 effects, and clearer safety and regulatory frameworks for airport deployment.

08 HYDROGEN↗

DOE OSTI2024

Hot Hydrogen Testing of W-Coated UN Kernels in a Mo30W Matrix

Ceramic uranium mononitride (UN) is being considered as a reactor fuel for nuclear thermal propulsion. To avoid or reduce the dissociation of UN at the high temperatures needed, embedding it in a metallic matrix (cermet) has been proposed. To assess the viability of this concept, hot hydrogen testing of tungsten-coated UN kernels embedded in a Mo-30 wt% W (Mo30W) alloy matrix has been performed at temperatures from 1800°C to 2300°C. Both the isolated kernels and kernels consolidated by spark plasma sintering in the Mo30W matrix were tested. In addition to direct observations and mass loss measurements, the samples were analyzed by X-ray diffraction (XRD) and scanning electron microscopy (SEM)/energy dispersive X-ray spectroscopy (EDS) after each run. The decomposition of UN started at 1800°C despite the coating and matrix, and increased at 2000°C. Uranium seeped through the tungsten grain boundaries of the coating at all temperatures. The consolidated sample expanded irregularly at 2000°C through the formation of voids, and SEM/EDS analysis showed uranium-containing veins in the matrix consisting of U 2 Mo according to the XRD data. The observed pore generation at 2000°C was explained by the formation of water vapor from residual oxides and diffused hydrogen. At 2200°C and above, both the kernels and the consolidated samples melted through the formation of uranium or low–melting point uranium-molybdenum alloys.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

Integration of sensors through additive manufacturing leading to increased efficiencies of gas turbines for power generation and propulsion

To realize the full capability of additively manufactured components in complex energy systems, it is imperative to minimize early component failures during development phases and during operation. Traditional field feedback timelines and offline inspection protocols significantly reduce the design-manufacturing iteration times. To address this specific question, the project developed and demonstrated a method for the integration of sensors into complex components through additive manufacturing. The team used gas turbine engines as a platform, which meets the need of both power generation and propulsion and offer opportunities for cost reductions and efficiency increases. The innovation of this intelligent integration of sensors into complex components uniquely customized to address questions of integrity and durability for additively manufactured components. With real-time sensing data from additively manufactured components, turbine manufacturers will realize higher efficiencies, reduced component failures, and a 30-50% acceleration in product deployment of high efficiency gas turbine components due to a faster reduction in component risk assessment under actual operating conditions. This is a transformative shift towards a data-driven design and qualification of additively manufactured gas turbine components. To directly integrate sensors into additively manufactured components with all the complexities of actual hardware, powder bed fusion (direct metal laser sintering) and laser metal deposition technologies was developed. Validation took take place in two university laboratories both of which contain actual engine hardware and closely simulate a gas turbine prior to demonstrating the technology in a turbine development test. Indeed, two major technologies from this research cold impact turbine systems in the near future: (1) higher efficiency materials and designs enabled by additive manufacturing with 50% faster design to manufacturing cycle time, to enable faster time-to-market targets; and (2) integration of sensors into additively manufactured components enabling broad health and condition based prognostics for faster component and engine risk reduction.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2017

Impact of Active Climate Control Seats on Energy Use, Fuel Use, and CO2 Emissions

A project was developed through collaboration between Gentherm and NREL to determine the impact of climate control seats for light-duty vehicles in the United States. The project used a combination of experimentation and analysis, with experimental results providing critical input to the analysis process. First, outdoor stationary vehicle testing was performed at NREL's facility in Golden, CO using multiple occupants. Two pre-production Ford Focus electric vehicles were used for testing; one containing a standard inactive seat and the second vehicle containing a Gentherm climate control seat. Multiple maximum cool-down and steady-state cooling tests were performed in late summer conditions. The two vehicles were used to determine the increase in cabin temperature when using the climate control seat in comparison to the baseline vehicle cabin temperature with a standard seat at the equivalent occupant whole-body sensation. The experiments estimated that on average, the climate control seats allowed for a 2.61 degrees Celsius increase in vehicle cabin temperature at equivalent occupant body sensation compared to the baseline vehicle. The increased cabin air temperature along with their measured energy usage were then used as inputs to the national analysis process. The national analysis process was constructed from full vehicle cabin, HVAC, and propulsion models previously developed by NREL. In addition, three representative vehicle platforms, vehicle usage patterns, and vehicle registration weighted environmental data were integrated into the analysis process. Both the baseline vehicle and the vehicle with climate control seats were simulated, using the experimentally determined cabin temperature offset of 2.61degrees Celsius and added seat energy as inputs to the climate control seat vehicle model. The U.S. composite annual fuel use savings for the climate control seats over the baseline A/C system was determined to be 5.1 gallons of gasoline per year per vehicle, corresponding to 4.0 grams of CO2/mile savings. Finally, the potential impact of 100 percent adoption of climate control seats on U.S. light-duty fleet A/C fuel use was calculated to be 1.3 billion gallons of gasoline annually with a corresponding CO2 emissions reduction of 12.7 million tons. Direct comparison of the impact of the CCS to the ventilated seat off-cycle credit was not possible because the NREL analysis calculated a combined car/truck savings and the baseline A/C CO2 emissions were higher than EPA. To enable comparison, the CCS national A/C CO2 emissions were split into car/truck components and the ventilated seat credit was scaled up. The split CO2 emissions savings due to the CCS were 3.5 g/mi for a car and 4.4 g/mi for a truck. The CCS saved an additional 2.0 g/mi and 2.5 g/mi over the adjusted ventilated seat credit for a car and truck, respectively.

30 DIRECT ENERGY CONVERSION↗

DOE OSTI2018

UTEMPRA - Unitary Thermal Energy Management for Propulsion Range Augmentation

Key hurdles to achieving wide consumer acceptance of battery electric vehicles (BEVs) are weather-dependent drive range, higher cost, and limited battery life. These translate into a strong need to reduce a significant energy drain and resulting drive range loss due to auxiliary electrical loads the predominant of which is the cabin thermal management load. Studies have shown that thermal subsystem loads can reduce the drive range by as much as 45% under ambient temperatures below -10 degrees C. Often, cabin heating relies purely on positive temperature coefficient (PTC) resistive heating, contributing to a significant range loss. Reducing this range loss may improve consumer acceptance of BEVs. The authors present a unified thermal management system (UTEMPRA) that satisfies diverse thermal and design needs of the auxiliary loads in BEVs. Demonstrated on a 2015 Fiat 500e BEV, this system integrates a semi-hermetic refrigeration loop with a coolant network and serves three functions: (1) heating and/or cooling vehicle traction components (battery, power electronics, and motor), (2) heating and cooling of the cabin, and (3) waste energy harvesting and re-use. The modes of operation allow a heat pump and air conditioning system to function without reversing the refrigeration cycle to improve thermal efficiency. The refrigeration loop consists of an electric compressor, a thermal expansion valve, a coolant-cooled condenser, and a chiller, the latter two exchanging heat with hot and cold coolant streams that may be directed to various components of the thermal system. The coolant-based heat distribution is adaptable and saves significant amounts of refrigerant per vehicle. Also, a coolant-based system reduces refrigerant emissions by requiring fewer refrigerant pipe joints. The authors present bench-level test data and simulation analysis and describe a preliminary control scheme for this system.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2020

Cummins Electric Truck with Range-Extending Engine (ETREE) Project (Final Technical Report)

The Cummins Electric Truck with Range Extending Engine (ETREE) program designed, developed, and demonstrated a range extending electric vehicle that employs an electrified propulsion system installed in a class 6 commercial vehicle (Peterbilt 220). This project was relevant to industry and the greater public because at the time of the project there were two keys to widespread electrified commercial vehicle adoption yet to be realize: 1) For pure electrified vehicle adoption, battery improvements are needed: Cost must decrease, and energy density must increase. 2) Electric vehicles must overcome fleet operator risks such as: operations in cold climates, hilly terrain, or where majority of conventional trucks are replaced with electrified vehicles. In the near to medium term these adoption hurdles were address by the objectives of this project. A plug-in hybrid vehicle that could be operated in all electric mode for most of its workday optimizing the use of grid energy with the ability to supplement energy demand with the onboard range extending engine. This project’s architecture provided ability to match a conventional class 6 commercial vehicle range and performance characteristics prior to the ubiquitous adoption of battery electric vehicle charging infrastructure as well. Additionally, the vehicles produced as part of this project can be considered a prototype for a commercially viable heavily electrified commercial vehicle because most of the physical hardware used for the project is commercially available in the market today. The ETREE program met its main objectives and demonstrated 65% fuel consumption reduction as compared to a conventional class 6 vehicle while meeting performance and range expectations. This was achieved by drawing upon the strengths of the assembled team: Cummins, PACCAR, the Ohio State University, Argonne National Laboratory and the National Renewable Energy Laboratory.

20 FOSSIL-FUELED POWER PLANTS↗

DOE OSTI2024

Propulsion Electrification Architecture Selection Process and Cost of Carbon Abatement Analysis for Heavy-Duty Off-Road Material Handler

The heavy-duty off-road industry continues to expand efforts to reduce fuel consumption and CO 2 e (carbon dioxide equivalent) emissions. Many manufacturers are pursuing electrification to decrease fuel consumption and emissions. Future policies will likely require electrification for CO2e savings, as seen in light-duty on-road vehicles. Electrified architectures vary widely in the heavy-duty off-road space, with parallel hybrids in some applications and series hybrids in others. The diverse applications for different types of equipment mean different electrified configurations are required. Companies must also determine the value in pursuing electrified architectures; this work analyzes a range of electrified architectures, from micro hybrids to parallel hybrids to series hybrids to a BEV, looking at the total cost, total CO 2 e, and cost per CO 2 e (cost of carbon abatement, or cost of carbon reduction) using data for the year 2021. This study is focused on a heavy-duty off-road material handler, the Pettibone Cary-Lift 204i. This machine’s specialty application, including events like unloading large oil pipes from a railcar, requires a unique electrified architecture that suits its specific needs. However, the results from this study may be extrapolated to similar machinery to inform fuel savings options across the heavy-duty off-road industry. In this study, a unique electrified architecture is determined for the Cary-Lift. This architecture is informed by multiple rounds of a Pugh matrix decision analysis to select a shortened list of desirable electrified architectures. The shortened list is modeled and simulated to determine CO 2 e, cost, and cost per CO 2 e. A final architecture is determined as a plug-in series hybrid that reduces fuel consumption by 65%, targeting the large fuel and CO 2 e savings that are likely to be required for the future of the heavy-duty off-road industry.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2025

Vehicle-Cycle Inventory for Type C School Buses & Intra-City Transit Buses

This report documents the new inventory incorporated into the Research and Development version of Greenhouse gases, Regulated Emissions, and Energy use in Technologies (R&D GREET) 2025 model for the vehicle cycle of Type C school buses and intracity transit buses. The transportation sector contributes significantly to the United States’ energy consumption and resultant emissions (EPA, 2025a). However, public transit plays an important role in mitigating these impacts because it consumes a relatively low amount of energy per passenger (Congressional Budget Office, 2022). Public transit is widely used in the United States; more than 500,000 school buses (EPA, 2025b) and ~75,000 service buses (American Public Transportation Association, 2025) operate in the nation. These are primarily internal combustion engine vehicles (ICEVs) powered by diesel. Original equipment manufacturers (OEMs) are making efforts to electrify U.S. bus fleets by using batteries as a propulsion system to replace internal combustion engines. Electrification can reduce tailpipe emissions, such as particulate matter (with a diameter ≤10 µm [PM 10 ] and with a diameter ≤2.5 µm [PM 2.5 ]) and nitrogen oxides (Jonas et al., 2025; Martinez and Samaras, 2024; EPA, 2025b; Wayne et al., 2009). Hence, any energy and emission impact analysis of public transit must consider both conventional ICEVs and upcoming electric vehicle (EV) options for the school and transit buses that dominate this landscape. To understand the detailed environmental impact profiles of ICEV and EV school and transit buses, it is necessary to conduct a thorough analysis covering both vehicle manufacturing and vehicle use stages. The current literature lacks a detailed vehicle-cycle inventory for school and transit buses, which makes this kind of comparison difficult. To overcome this gap, we developed a comprehensive vehicle-cycle model for school and transit buses in Argonne’s R&D GREET 2025 model. The model is flexible in handling user inputs for key assumptions, such as component weights and material compositions, upstream energy sources for material processing, and vehicle operating parameters, to understand their impacts on energy use and emissions for both school and transit buses. This report is organized as follows: Section 2 provides details on the modeling approach and vehicle specifications (weights and composition of different vehicle components, and vehicle operating parameters) for both school and transit buses. Section 3 provides details on vehicle assembly, disposal, and recycling (ADR) approaches for the two buses. Section 4 includes details about their incorporation into the R&D GREET model.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2023

Pressure effects on reactivity and extinction of n -dodecane diffusion cool flame

Low-temperature combustion at high pressure has gained increasing interest owing to the growing demand for clean and efficient propulsion and energy systems. In particular, cool flame structure, extinction limits, and fuel reactivities at high pressure are critical in affecting the engine performance at near-limit conditions. Here, this paper investigates the effects of pressure on the cool flame extinction limit, structure, radical index, reactivity, and oxygen concentration dependence by experiments, analysis, and modeling. A large n-alkane, namely n-dodecane (n C 12 H 26 ), is selected to study its diffusion cool flame dynamics and reactivity in a high-pressure counterflow burner up to 10 atm. The experimental results show that higher pressure increases the cool flame extinction strain rates, and that the pressure-weighted extinction strain rate (aP) is proportional to the square of pressure, P 2 . A scaling analysis explains the relationship between the dependence of flame structure, heat release rate, and pressure-weighted cool flame strain rate on pressure. Furthermore, radical indexes at different pressures are measured by isolating the thermal and transport effects from the chemical contribution to diffusion cool flame extinction. The radical index clearly shows that the low-temperature reactivity increases with pressure. In addition, due to the critical role of multiple oxygen addition reactions in low-temperature chemistry, the relationship between the cool flame extinction limit and the oxygen concentration is explored. It is found that the cool flame extinction limits are proportional to the n th power of the oxygen concentration, [O 2 ] n , and increasing pressure leads to stronger extinction limit dependence (larger n) on the oxygen concentration. The present experiment and detailed kinetic analysis show clearly that increasing pressure promotes the low-temperature chemistry including the oxygen addition reactions, while the scaling analysis explains well the experimental results.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2023

Kinetics and extinction of non-premixed cool and warm flames of dimethyl ether at elevated pressure

Here, the growing demand of clean and efficient propulsion and energy systems has sparked an interest in understanding low-temperature combustion at high pressure. Cool flame transition and extinction limits as well as oxygen concentration dependence at elevated pressures provide insights of the low-temperature and high-pressure fuel reactivity. A new experimental high-pressure counterflow burner platform was designed and developed to achieve the studies of high-pressure cool flames. Dimethyl ether (DME) was chosen to study its non-premixed cool flame in high-pressure counterflow burner at pressure up to 5 atm, perhaps for the first time. This paper investigates the effects of pressure on cool flame structure, extinction and transition limits, and oxygen concentration dependence as well as ozone assisted warm flames of DME in experiments and numerical simulations. The results show that the reignition transition from cool flame to hot flame occurs either with the decrease of the strain rate at a given fuel concentration and pressure or with the increase of fuel mole fraction or pressure at a given strain rate. Furthermore, it is shown that the higher pressure shifts the cool flame to higher strain rates and results in higher cool flame extinction strain rates. However, the existing kinetic model of DME fails in predicting the cool flame extinction limit at elevated pressures. Besides, the cool flame extinction limits are proportional to nth power of the oxygen concentration, [O 2 ] n , and the increase of pressure leads to stronger extinction limit dependence (larger n) on oxygen concentration. The present experiment and detailed kinetic analysis show clearly that increasing pressure promotes the low-temperature chemistry including the oxygen addition reactions. In addition, stable warm flame was first experimentally observed by using DME at elevated pressure with ozone sensitization.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2015

Characterization of Contact and Bulk Thermal Resistance of Laminations for Electric Machines

Thermal management for electric motors is important as the automotive industry continues to transition to more electrically dominant vehicle propulsion systems. The transition to more electrically dominant propulsion systems leads to higher-power duty cycles for electric-drive systems. Thermal constraints place significant limitations on how electric motors ultimately perform. As thermal management improves, there will be a direct trade-off among motor performance, efficiency, cost, and the sizing of electric motors to operate within the thermal constraints. During the development of thermal finite element analysis models and computational fluid dynamics models for electric motors, it was found that there was a lack of open literature detailing the thermal properties of key materials common in electric motors that are significant in terms of heat removal. The lack of available literature, coupled with the strong interest from industry in the passive-stack thermal measurement results, led to experiments to characterize the thermal contact resistance between motor laminations. We examined four lamination materials, including the commonly used 26 gauge and 29 gauge M19 materials, the HF10 and Arnon 7 materials. These latter two materials are thinner and reduce eddy currents responsible for core losses. We measured the thermal conductivity of the lamination materials and the thermal contact resistance between laminations in a stack, as well as investigated factors affecting contact resistance between laminations such as the contact pressure and surface finish. Lamination property data will be provided and we also develop a model to estimate the through-stack thermal conductivity for materials beyond those that were directly tested in this work. For example, at a clamping pressure of 138 kPa, the 29 gauge M19 material has a through-stack thermal conductivity of 1.68 W/m-K, and the contact resistance between laminations was measured to be 193 mm^2-K/W. The measured bulk thermal conductivity for the M19 29 gauge material is 21.0 W/m-K. Density and specific heat were measured to be 7450 kg/m^3 and 463 J/kg-K, respectively. These results are helping, and will continue to help engineers and researchers in the design and development of motors.

33 ADVANCED PROPULSION SYSTEMS↗