Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “AXIAL RATIO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,063 records · Page 59
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Plasma Exhaust in a Sheared-Flow-Stabilized Z Pinch

The fusion Z-pinch experiment device produces a 0.3 cm radius by 50 cm-long Z pinch between the end of the inner electrode of a coaxial plasma gun and an end wall 50 cm away. The plasma column is stabilized for thousands of instability growth times by an embedded radially sheared axial plasma flow. To investigate the effect of end wall design on Z-pinch plasma behavior, the solid end wall with a central exhaust port is replaced with a spoked end wall with a solid hub. While the Z-pinch plasma behavior was largely unaffected, the plasma exhausted from the Z-pinch provides an experimental platform to study magnetic confinement and detachment. Here, current and density signals are compared between two cases: a low energy and a high energy case. Plasma is found to be frozen-in flux in the Z-pinch assembly region. The exhaust of plasma from the flux conserving region is found to be dependent on the ratio of plasma ram and thermal pressures to the local magnetic pressure, calculated from an equilibrium model at the end wall. Plasma exhaust is observed to increase with the spoked end wall only for the high energy conditions as its ratio of ram and thermal pressures to the magnetic pressure increases.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1980

Buckling of axially compressed conical shells

The buckling of a truncated elastic conical shell subjected to an axial compression is a classical problem in shell structures. The paper reinvestigates the buckling of an axially compressed truncated conical shell with rigid bulkheads. Two improvements are achieved. First, the condition that the total horizontal displacement must vanish due to rigid bulkhead and axisymmetry is treated as a constraint. This constraint is incorporated into the system through the use of the Lagrange multiplier; then the variational method is used to derive a complete set of boundary conditions for conical shells. Second, the stability is evaluated in the deformed state using the asymptotic solutions of the pair of Donnell-type equations for axisymmetric configuration. The results indicate that the buckling strength of conical shells depends mainly on the condition of the smaller end. In addition to the vertex angle, the distance ratio plays, at least, an equally important role.

Chang, C.-H.↗
NASA NTRS1993

Every Good Virtue You Ever Wanted in a Q-switched Solid-state Laser and More: Monolithic, Diode-pumped, Self-q-switched, Highly Reproducible, Diffraction-limited Nd:yag Laser

The applications of Q-switched lasers are well known, for example, laser radar, laser remote sensing, satellite orbit determination, Moon orbit and 'moon quake' determination, satellite laser communication, and many nonlinear optics applications. Most of the applications require additional properties of the Q-switched lasers, such as single-axial and/or single-transverse mode, high repetition rate, stable pulse shape and pulse width, or ultra compact and rugged oscillators. Furthermore, space based and airborne lasers for lidar and laser communication applications require efficient, compact, lightweight, long-lived, and stable-pulsed laser sources. Diode-pumped solid-state lasers (DPSSL) have recently shown the potential for satisfying all of these requirements. We will report on the operating characteristics of a diode-pumped, monolithic, self-Q-switched Cr,Nd:YAG laser where the chromium ions act as a saturable absorber for the laser emission at 1064 nm. The pulse duration is 3.5 ns and the output is highly polarized with an extinction ratio of 700:1. It is further shown that the output is single-longitudinal-mode with transform-limited spectral line width without pulse-to-pulse mode competition. Consequently, the pulse-to-pulse intensity fluctuation is less than the instrument resolution of 0.25 percent. This self-stabilization mechanism is because the lasing mode bleaches the distributed absorber and establishes a gain-loss grating similar to that used in the distributed feedback semiconductor lasers. A repetition rate above 5 KHz has also been demonstrated. For higher power, this laser can be used for injection seeding an amplifier (or amplifier chain) or injection locking of a power oscillator pumped by diode lasers. We will discuss some research directions on the master oscillator for higher output energy per pulse as well as how to scale the output power of the diode-pumped amplifier(s) to multi-kilowatt average power.

Chen, Y. C.↗
DOE OSTI2024

Flow and Performance Characterization of Rotating Detonation Combustor Integrated with Various Convergent Nozzles

In this study, convergent nozzles of various area ratios (ARs) are used downstream of an annular rotating detonation combustor (RDC) to increase the operating pressure and approach sonic conditions at the nozzle throat. Reactant methane and oxygen-enriched air (67% [Formula: see text] and 33% [Formula: see text] by volume) are supplied in counterflow arrangement from two separate plenums located at the base of the RDC annulus. Based on experimentation, a total mass flow rate of [Formula: see text] was chosen to achieve stable, single-wave mode RDC operation for all test cases, allowing for one-to-one comparisons. The internal performance of the RDC was characterized by ion probes and pressure measurements (wall static and oscillating) in supply plenums and across different axial locations of the combustor. Particle image velocimetry (PIV) at 100 kHz was utilized to measure axial and circumferential velocity components within a two-dimensional region of interest located downstream of the converging nozzle exit. Results show higher internal performance of the RDC with increasing AR of the convergent nozzle. PIV measurement illustrated that the flow oscillation amplitudes decrease with an increasing AR of the converging nozzle. The exit flow contained significant nonuniformity and unsteadiness even with a converging nozzle of AR 2.0, indicating incomplete choking of the flow at the nozzle throat.

Engineering↗
NASA NTRS1984

Heat pipe applications in aircraft propulsion

Heat pipes for improving the cycle efficiency and/or thrust-to-weight ratio of aircraft gas turbines are examined. A heat pipe employs a capillary structure, a wick, and an evacuated chamber to transfer heat between condensor and evaporator ends. Heat absorbed at the evaporator is transported to the condensor. In an aircraft, the heat pipe can be stationary or rotating, can be used for cooling stators and rotors, and is amenable to shapes such as cylinders, cones, and flat plates. Heat pipes in aircraft gas turbines can be applied for intercooling between stages, regeneration, reheat, and blade cooling. Improvements are projected in the cycle efficiency, thrust and thrust specific fuel consumption in the fanjet by using heat pipes. Consideration is also given to heat pipe heat exchangers with high axial heat transfer for stationary heat pipes and high heat transport for rotating heat pipes.

Beltran, M. R.↗
NASA NTRS1947

Altitude-Wind-Tunnel Investigation of the 19B-2, 19B-8 and 19XB-1 Jet- Propulsion Engines: Analysis of Compressor Performance - 4

Investigations were conducted in the Cleveland altitude wind tunnel to determine the performance and operational characteristics of the 19B-2, 19B-8, and 19XS-1 turbojet engines. One objective was to determine the effect of altitude, flight Mach number, and tail-pipe-nozzle area on the performance characteristics of the six-stage and ten-stage axial-flow compressors of the 19B-8 and 19XB-1 engines, respectively, The data were obtained over a range of simulated altitudes and flight Mach numbers. At each simulated flight condition the engine was run over its full operable range of speeds. Performance characteristics of the 19B-8 and 19XB-1 compressors for the range of operation obtainable in the turboJet-engine installation are presented. Compressor characteristics are presented as functions of air flow corrected to sea-level conditions, compressor Mach number, and compressor load coefficient. For the range of compressor operation investigated, changes in Reynolds number had no measurable effect on the relations among compressor Mach number, corrected air flow, compressor load coefficient, compressor pressure ratio, and compressor efficiency. The operating lines for the 19B-8 compressor lay on the low-air-flow side of the region of maximum compressor efficiency; the 19B-8 compressor operated at higher average pressure coefficients per stage and produced a lower over-all pressure ratio than did the 19XB-1 compressor.

Dietz, Robert O.↗
NASA NTRS1982

A FORTRAN program for calculating three dimensional, inviscid and rotational flows with shock waves in axial compressor blade rows: User's manual

A FORTRAN-IV computer program was developed for the calculation of the inviscid transonic/supersonic flow field in a fully three dimensional blade passage of an axial compressor rotor or stator. Rotors may have dampers (part span shrouds). MacCormack's explicit time marching method is used to solve the unsteady Euler equations on a finite difference mesh. This technique captures shocks and smears them over several grid points. Input quantities are blade row geometry, operating conditions and thermodynamic quanities. Output quantities are three velocity components, density and internal energy at each mesh point. Other flow quanities are calculated from these variables. A short graphics package is included with the code, and may be used to display the finite difference grid, blade geometry and static pressure contour plots on blade to blade calculation surfaces or blade suction and pressure surfaces. The flow in a low aspect ratio transonic compressor was analyzed and compared with high response total pressure probe measurements and gas fluorescence static density measurements made in the MIT blowdown wind tunnel. These comparisons show that the computed flow fields accurately model the measured shock wave locations and overall aerodynamic performance.

Thompkins, W. T., Jr.↗
DOE OSTI2022

Near-wake dynamics of a vertical-axis turbine

Cross-flow, or vertical-axis, turbines are a promising technology for capturing kinetic energy in wind or flowing water and their inherently unsteady fluid mechanics present unique opportunities for control optimization of individual rotors or arrays. To explore the potential for beneficial interactions between turbines in an array, as well as to characterize important cycle-to-cycle variations, coherent structures in the wake of a single two-bladed cross-flow turbine are examined using planar stereo particle image velocimetry in a water channel experiment. There are three main objectives in the present work. First, the mean wake structure of this high chord-to-radius ratio rotor is described, compared with previous studies, and a simple explanation for observed wake deflection is presented. Second, the unsteady flow is then analysed via the triple decomposition, with the periodic component extracted using a combination of traditional techniques and a novel implementation of the optimized dynamic mode decomposition. The latter method is shown to outperform conditional averaging and Fourier methods, as well as uncover frequencies suggesting a transition to bluff-body shedding in the far wake. Third, vorticity and finite-time Lyapunov exponents are then employed to further analyse the oscillatory wake component. Vortex streets on both sides of the wake are identified, and their formation mechanisms and effects on the mean flow are discussed. Strong axial (vertical) flow is observed in vortical structures shed on the retreating side of the rotor where the blades travel downstream. Time-resolved tracking of these vortices is performed, which demonstrates that vortex trajectories have significant rotation-to-rotation variation within one diameter downstream. This variability suggests it would be challenging to harness or avoid such structures at greater downstream distances.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
NASA NTRS1994

Twin engine afterbody model

This test was originally conducted to determine the effects of several empennage and afterbody parameters on the aft-end aerodynamic characteristics of a twin-engine fighter-type configuration. Model variables were as follows: horizontal tail axial location and incidence, vertical tail axial location and configuration (twin-vs single-tail arrangements), tail booms, and nozzle power setting. Jet propulsion was simulated by exhausting high-pressure, cold-flow air from the nozzles. Following a successful test conducted on a single engine nacelle model to validate a CFD code, this model was chosen to be instrumented with pressure taps on the afterbody and nozzles and used as a follow-on test, providing a more complex geometry for the CFD code validation. A more limited test matrix was run to collect the pressure data, employing only the twin-tail configuration and varying only the horizontal and vertical tail locations. Mach number was varied from 0.6 to 1.2. Nozzle pressure ratio was varied from jet-off to 8. Angle-of-attack varied from 0 to 8 deg.

Wing, David J.↗
NASA NTRS2003

Enhanced Mixing in a Rectangular Duct

An experimental investigation of the mixing of non-reacting opposed rows of jets injected normal to a confined rectangular crossflow has been conducted. Planar Mie-scattering was used to measure the time-average concentration distribution of the jet fluid in planes perpendicular to the duct axis. Particular emphasis was placed on the study of closely spaced orifice configurations applicable to the mixing zone of an RQL combustor. Baseline studies were performed of mixing under "ideal" conditions, i.e., plenum fed jets injecting into a crossflow uniform in velocity and turbulence intensity. In addition, more practical ("non-ideal") issues encountered during hardware design were also studied. As in other studies, mixing effectiveness, determined using a spatial unmixedness parameter based on the variance of mean jet concentration distributions, was found to be optimum when the spacing-to-duct-height ratio was inversely proportional to the square root of the jet-to-mainstream momentum-flux ratio. This relationship is suitable for design under ideal flow conditions. Inlet flow boundary conditions of the jet and approach flow (mainstream) were found to strongly influence mixing performance, but no attempt was made to determine optimum performance under non-ideal conditions. The tests performed do offer some guidance as to expected mixing behavior for several common variables likely to be imposed by hardware constraints. Additionally, in this study it was found that for rows of orifices with opposite centerlines inline, mixing was similar for blockages up to 89 percent (previous crossflow mixing studies concerned with dilution zone configurations, blockages were typically less than 50 percent). Lower levels of unmixedness were obtained as a function of downstream location when axial injection length was minimized. Mixing may be enhanced if orifice centerlines of opposed rows are staggered, but blockage must be =50 percent in this configuration. Round hole and "square" orifice shapes had similar performance. Other variations in orifice shape did not substantially augment overall mixing performance. Furthermore an isothermal mixing data set was generated and used by CFDRC as input to a NO(x) inference code.

Liscinsky, D. S.↗
NASA NTRS2018

Dual Rotating Rake Measurements of Higher-Order Duct Modes: Validation Using Experimental and Numerical Data

A rotating rake mode measurement system was designed to measure acoustic duct modes generated by a fan stage. After analysis of the measured data, the mode coefficient amplitudes and phases were quantified. Early studies using this system found that mode power levels computed from rotating rake measured data would agree with the far-field power levels. However, this agreement required that the sound from the noise sources within the duct propagated outward from the duct exit without reflection and previous studies suggested conditions could exist where significant reflections could occur. This paper shows that mounting a second rake to the rotating system, with an offset in both the axial and the azimuthal directions, measures the data necessary to determine the modes propagating in both directions within a duct. The rotating rake data analysis technique was extended to include the data measured by the second rake. The analysis resulted in a set of circumferential mode coefficients at each of the two rake microphone locations. Radial basis functions were then least-squares fit to this data to obtain the radial mode coefficients for the modes propagating in both directions within the duct while accounting for the presence of evanescent modes. The validation of the dual-rotating-rake measurements was conducted using data from a combination of experiments and numerical calculations to compute reflection coefficients and other mode coefficient ratios. Compared to results from analytical and numerical computations, the results from dual-rotating-rake measured data followed the expected trends when frequency, mode number, and duct termination geometry were changed.

Validation↗
NASA NTRS1972

Minimum weight design of ring and stringer stiffeners for axially compressed cylindrical shells with and without internal pressure

Results of analytical study to determine desirable ring and stringer stiffener parameters and proportions for axially compressed stiffened isotropic cylinders with and without internal pressure are presented. This investigation examines the panel and general instability buckling modes of a stiffened cylindrical shell and from this determines desirable stiffener parameters and proportions. Classical buckling equations are used which retain the important effects of the stiffeners. The results determined by using the simpler classical buckling equations are then spot checked and verified using buckling equations which considered discrete ring stiffeners and nonlinear prebuckling deformations. For both rings and stringers, T-shaped stiffeners are preferable and the effects to stiffener shape are much more pronounced at low or zero values of the internal pressure parameter. Simple analytical expressions are developed and presented which express the stiffener area parameter, the ratio of stiffener area and elastics to shell wall area and elastic modulus, in terms of the cylinder geometry and internal pressure parameter.

Block, D. L.↗
DOE OSTI2023

MHD simulation on magnetic compression of field reversed configurations with NIMROD

Abstract Magnetic compression has long been proposed a promising method for plasma heating in a field reversed configuration (FRC). However, it remains a challenge to fully understand the physical mechanisms underlying the compression process, due to its highly dynamic nature beyond the one-dimensional (1D) adiabatic theory model (Spencer et al 1983 Phys. Fluids 26 1564). In this work, magnetohydrodynamics simulations on the magnetic compression of FRCs using the NIMROD code (Sovinec et al 2004 J. Comput. Phys. 195 355) and their comparisons with the 1D theory have been performed. The effects of the assumptions of the theory on the compression process have been explored, and the detailed profiles of the FRC during compression have been investigated. The pressure evolution agrees with the theoretical prediction under various initial conditions. The axial contraction of the FRC can be affected by the initial density profile and the ramping rate of the compression magnetic field, but the theoretical predictions on the FRC’s length in general and the relation r s = 2 r o in particular hold approximately well during the whole compression process, where r s is the major radius of FRC separatrix and r o is that of the magnetic axis. The evolutions of the density and temperature can be affected significantly by the initial equilibrium profile and the ramping rate of the compression magnetic field. During the compression, the major radius of the FRC is another parameter that is susceptible to the ramping rate of the compression field. Basically, for the same magnetic compression ratio, the peak density is higher and the FRC’s radius r s is smaller than the theoretical predictions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2014

Design Optimization of a Variable-Speed Power Turbine

NASA's Rotary Wing Project is investigating technologies that will enable the development of revolutionary civil tilt rotor aircraft. Previous studies have shown that for large tilt rotor aircraft to be viable, the rotor speeds need to be slowed significantly during the cruise portion of the flight. This requirement to slow the rotors during cruise presents an interesting challenge to the propulsion system designer as efficient engine performance must be achieved at two drastically different operating conditions. One potential solution to this challenge is to use a transmission with multiple gear ratios and shift to the appropriate ratio during flight. This solution will require a large transmission that is likely to be maintenance intensive and will require a complex shifting procedure to maintain power to the rotors at all times. An alternative solution is to use a fixed gear ratio transmission and require the power turbine to operate efficiently over the entire speed range. This concept is referred to as a variable-speed power-turbine (VSPT) and is the focus of the current study. This paper explores the design of a variable speed power turbine for civil tilt rotor applications using design optimization techniques applied to NASA's new meanline tool, the Object-Oriented Turbomachinery Analysis Code (OTAC).

design optimization↗
DOE OSTI2020

A multi-dimensional dataset for two-phase instability in low pressure natural circulation based on direct transient local measurement

Thermal hydraulic instability can challenge the control and the safety of nuclear reactors. This experimental research captures and investigates the instability in a low-pressure (1–10 atmospheres) natural circulation loop with an adiabatic chimney installed above the heated section. Direct transient local measurement of two-phase flow is performed at multiple axial locations along the flow channel with thermocouples and conductivity probes traversed by customized high-precision mechanisms. Based on the periodicity of oscillations, a post-processing method is proposed to align the data captured non-simultaneously to reconstruct the instability behavior in one representative period. The averaging operation over multiple oscillation cycles is performed to reduce the random errors. Cyclic phenomena are clearly demonstrated by the post-processed data, and rapid void fraction change induced by the flashing is observed to be significant in the driving mechanism for low pressure oscillations. Parametric effects of inlet subcooling, heat flux, inlet flow restriction and system pressure are studied within the experiment range, and qualitative results are explained and compared with existing literature. The ratio between the oscillation period and the travelling time of the fluid particle through the test section is compared with the theoretical value for the density wave oscillation. The new dataset contains directly measured transient multi-dimensional two-phase data along the flow channel for natural circulation under density wave oscillations. The generated dataset is valuable for the validation of system analysis codes and CFD codes in the simulation of natural circulation phenomena and dynamic two-phase flow.

42 ENGINEERING↗
NASA NTRS1996

Analysis of Two-Phase Flow in Damper Seals for Cryogenic Turbopumps

Cryogenic damper seals operating close to the liquid-vapor region (near the critical point or slightly su-cooled) are likely to present two-phase flow conditions. Under single phase flow conditions the mechanical energy conveyed to the fluid increases its temperature and causes a phase change when the fluid temperature reaches the saturation value. A bulk-flow analysis for the prediction of the dynamic force response of damper seals operating under two-phase conditions is presented as: all-liquid, liquid-vapor, and all-vapor, i.e. a 'continuous vaporization' model. The two phase region is considered as a homogeneous saturated mixture in thermodynamic equilibrium. Th flow in each region is described by continuity, momentum and energy transport equations. The interdependency of fluid temperatures and pressure in the two-phase region (saturated mixture) does not allow the use of an energy equation in terms of fluid temperature. Instead, the energy transport is expressed in terms of fluid enthalpy. Temperature in the single phase regions, or mixture composition in the two phase region are determined based on the fluid enthalpy. The flow is also regarded as adiabatic since the large axial velocities typical of the seal application determine small levels of heat conduction to the walls as compared to the heat carried by fluid advection. Static and dynamic force characteristics for the seal are obtained from a perturbation analysis of the governing equations. The solution expressed in terms of zeroth and first order fields provide the static (leakage, torque, velocity, pressure, temperature, and mixture composition fields) and dynamic (rotordynamic force coefficients) seal parameters. Theoretical predictions show good agreement with experimental leakage pressure profiles, available from a Nitrogen at cryogenic temperatures. Force coefficient predictions for two phase flow conditions show significant fluid compressibility effects, particularly for mixtures with low mass content of vapor. Under these conditions, an increase on direct stiffness and reduction of whirl frequency ratio are shown to occur. Prediction of such important effects will motivate experimental studies as well as a more judicious selection of the operating conditions for seals used in cryogenic turbomachinery.

Arauz, Grigory L.↗
DOE OSTI2022

Preliminary Thermal-hydraulics and Selected Safety Analysis for Holos-Quad Reactor Design

This report presents thermal hydraulics and safety analyses of the 10 MWe Holos-Quad micro-reactor design developed by HolosGen LLC. These analyses were executed under steady-state and station black-out (SBO) transient conditions using the System Analysis Module (SAM), with a focus on ensuring peak fuel temperatures do not exceed the safety thresholds of 1,250°C for steady state normal operating conditions and 1,600°C for transient conditions. For steady-state temperature predictions, a coupled 1D fluid-to-3D solid heat conduction methodology was used. The steady-state simulations included a model of the central core region where power peaking occurs to predict the maximum steady-state fuel temperature, and a coarse-mesh full-core model to provide the initial condition for the consequent transient SBO decay heat removal simulation. The maximum fuel temperature predicted from the central core region simulations under the normal operating condition was 1,222°C, which is below the design limit 1,250°C. To simulate a SBO transient, a full core model was necessary because of the non-axial symmetric core design and heat loss from the outer core structures to the environment. To reduce the required computational costs, a novel scaled subassembly approach was used to model the full core domain. With the full core steady-state temperature distribution provided as the initial condition, the passive decay heat removal of the core was simulated with the scaled subassembly full core model under SBO transient conditions. This analysis showed that the peak fuel temperatures of the Holos-Quad core remained below their steady-state values during the transient, therefore much lower than the safety limit 1,600°C. This is mainly due to the large thermal inertia of the graphite matrix, relatively low power density, and the large surface-to-volume-ratio of the core. The preliminary analyses presented in this report confirm the inherent safety of the Holos-Quad micro-reactor thermal-hydraulics design, as the peak fuel temperatures under both normal and off-normal operational conditions remain within design and safety limits.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
NASA NTRS2017

Computational Assessment of a 3-Stage Axial Compressor Which Provides Airflow to the NASA 11- by 11-Foot Transonic Wind Tunnel, Including Design Changes for Increased Performance

A 24 foot diameter 3-stage axial compressor powered by variable-speed induction motors provides the airflow in the closed-return 11- by 11-Foot Transonic Wind Tunnel (11-Foot TWT) Facility at NASA Ames Research Center at Moffett Field, California. The facility is part of the Unitary Plan Wind Tunnel, which was completed in 1955. Since then, upgrades made to the 11-Foot TWT such as flow conditioning devices and instrumentation have increased blockage and pressure loss in the tunnel, somewhat reducing the peak Mach number capability of the test section. Due to erosion effects on the existing aluminum alloy rotor blades, fabrication of new steel rotor blades is planned. This presents an opportunity to increase the Mach number capability of the tunnel by redesigning the compressor for increased pressure ratio. Challenging design constraints exist for any proposed design, demanding the use of the existing driveline, rotor disks, stator vanes, and hub and casing flow paths, so as to minimize cost and installation time. The current effort was undertaken to characterize the performance of the existing compressor design using available design tools and computational fluid dynamics (CFD) codes and subsequently recommend a new compressor design to achieve higher pressure ratio, which directly correlates with increased test section Mach number. The constant cross-sectional area of the compressor leads to highly diffusion factors, which presents a challenge in simulating the existing design. The CFD code APNASA was used to simulate the aerodynamic performance of the existing compressor. The simulations were compared to performance predictions from the HT0300 turbomachinery design and analysis code, and to compressor performance data taken during a 1997 facility test. It was found that the CFD simulations were sensitive to endwall leakages associated with stator buttons, and to a lesser degree, under-stator-platform flow recirculation at the hub. When stator button leakages were modeled, pumping capability increased by over 20 of pressure rise at design point due to a large reduction in aerodynamic blockage at the hub. Incorporating the stator button leakages was crucial to matching test data. Under-stator-platform flow recirculation was thought to be large due to a lack of seals. The effect of this recirculation was assessed with APNASA simulations recirculating 0.5, 1, and 2 of inlet flow about stators 1 and 2, modeled as axisymmetric mass flux boundary conditions on the hub before and after the vanes. The injection of flow ahead of the stators tended to re-energize the boundary layer and reduce hub separations, resulting in about 3 increased stall margin per 1 of inlet flow recirculated. In order to assess the value of the flow recirculation, a mixing plane simulation of the compressor which gridded the under-stator cavities was generated using the ADPAC CFD code. This simulation indicated that about 0.65 of the inlet flow is recirculated around each shrouded stator. This collective information was applied during the redesign of the compressor. A potential design was identified using HT0300 which improved overall pressure ratio by removing pre-swirl into rotor 1, replacing existing NASA 65 series rotors with double circular arc sections, and re-staggering rotors and the existing stators. The performance of the new design predicted by APNASA and HT0300 is compared to the existing design.

Turbomachinery↗