Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “wind tunnel testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58
All sourcesNASA NTRSDOE OSTI
NASA NTRS2017

Low-Reynolds Number Aerodynamics of an 8.9 Percent Scale Semispan Swept Wing for Assessment of Icing Effects

Aerodynamic assessment of icing effects on swept wings is an important component of a larger effort to improve three-dimensional icing simulation capabilities. An understanding of ice-shape geometric fidelity and Reynolds and Mach number effects on the iced-wing aerodynamics is needed to guide the development and validation of ice-accretion simulation tools. To this end, wind-tunnel testing and computational flow simulations were carried out for an 8.9 percent-scale semispan wing based upon the Common Research Model airplane configuration. The wind-tunnel testing was conducted at the Wichita State University 7 by 10 ft Beech wind tunnel from Reynolds numbers of 0.8×10(exp 6) to 2.4×10(exp 6) and corresponding Mach numbers of 0.09 to 0.27. This paper presents the results of initial studies investigating the model mounting configuration, clean-wing aerodynamics and effects of artificial ice roughness. Four different model mounting configurations were considered and a circular splitter plate combined with a streamlined shroud was selected as the baseline geometry for the remainder of the experiments and computational simulations. A detailed study of the clean-wing aerodynamics and stall characteristics was made. In all cases, the flow over the outboard sections of the wing separated as the wing stalled with the inboard sections near the root maintaining attached flow. Computational flow simulations were carried out with the ONERA elsA software that solves the compressible, threedimensional RANS equations. The computations were carried out in either fully turbulent mode or with natural transition. Better agreement between the experimental and computational results was obtained when considering computations with free transition compared to turbulent solutions. These results indicate that experimental evolution of the clean wing performance coefficients were due to the effect of three-dimensional transition location and that this must be taken into account for future data analysis. This research also confirmed that artificial ice roughness created with rapid-prototype manufacturing methods can generate aerodynamic performance effects comparable to grit roughness of equivalent size when proper care is exercised in design and installation. The conclusions of this combined experimental and computational study contributed directly to the successful implementation of follow-on test campaigns with numerous artificial ice-shape configurations for this 8.9 percent scale model.

Aerodynamics↗
NASA NTRS1988

Aeroelastic characteristics of the AH-64 bearingless tail rotor

The results of a wind tunnel test program to determine the performance loads and dynamic characteristics of the Composite Flexbeam Tail Rotor (CFTR) for the AH-64 Advanced Attack Helicopter are reported. The CFTR uses an elastomeric shear attachment of the flexbeam to the hub to provide soft-inplane S-mode and stiff-inplane C-mode configuration. The properties of the elastomer were selected for proper frequency placement and scale damping of the inplane S-mode. Kinematic pitch-lag coupling was introduced to provide the first cyclic inplane C-mode damping at high collective pitch. The CFTR was tested in a wind tunnel over the full slideslip envelop of the AH-64. It is found that the rotor was aeroelastically stable throughout the complete collective pitch range and up to rotor speeds of 1403 rpm. The dynamic characteristics of the rotor were found to be satisfactory at all pitch angles and rotor speeds of the tunnel tests. The design characteristics of the rotor which permit the high performance characteristics are discussed. Several schematic drawings and photographs of the rotor are provided.

Banerjee, D.↗
NASA NTRS1992

Aeroelastic stability analyses of two counter rotating propfan designs for a cruise missile model

Aeroelastic stability analyses were performed to insure structural integrity of two counterrotating propfan blade designs for a NAVY/Air Force/NASA cruise missile model wind tunnel test. This analysis predicted if the propfan designs would be flutter free at the operating conditions of the wind tunnel test. Calculated stability results are presented for the two blade designs with rotational speed and Mach number as the parameters. A aeroelastic analysis code ASTROP2 (Aeroelastic Stability and Response of Propulsion Systems - 2 Dimensional Analysis), developed at LeRC, was used in this project. The aeroelastic analysis is a modal method and uses the combination of a finite element structural model and two dimensional steady and unsteady cascade aerodynamic models. This code was developed to analyze single rotation propfans but was modified and applied to counterrotating propfans for the present work. Modifications were made to transform the geometry and rotation of the aft rotor to the same reference frame as the forward rotor, to input a non-uniform inflow into the rotor being analyzed, and to automatically converge to the least stable aeroelastic mode.

Mahajan, Aparajit J.↗
NASA NTRS2010

Structural Verification and Modeling of a Tension Cone Inflatable Aerodynamic Decelerator

Verification analyses were conducted on membrane structures pertaining to a tension cone inflatable aerodynamic decelerator using the analysis code LS-DYNA. The responses of three structures - a cylinder, torus, and tension shell - were compared against linear theory for various loading cases. Stress distribution, buckling behavior, and wrinkling behavior were investigated. In general, agreement between theory and LS-DYNA was very good for all cases investigated. These verification cases exposed the important effects of using a linear elastic liner in membrane structures under compression. Finally, a tension cone wind tunnel test article is modeled in LS-DYNA for which preliminary results are presented. Unlike data from supersonic wind tunnel testing, the segmented tension shell and torus experienced oscillatory behavior when subjected to a steady aerodynamic pressure distribution. This work is presented as a work in progress towards development of a fluid-structures interaction mechanism to investigate aeroelastic behavior of inflatable aerodynamic decelerators.

Tanner, Christopher L.↗
NASA NTRS1980

Experimental aerodynamic characteristics of two V/STOL fighter/attack aircraft configurations at Mach numbers from 0.4 to 1.4

A wind tunnel test was conducted to measure the aerodynamic characteristics of two horizontal attitude takeoff and landing V/STOL fighter/attack aircraft concepts. In one concept, a jet diffuser ejector was used for the vertical lift system; the other used a remote augmentation lift system (RALS). Wind tunnel tests to investigate the aerodynamic uncertainties and to establish a data base for these types of concepts were conducted over a Mach number range from 0.2 to 2.0. The present report covers tests, conducted in the 11 foot transonic wind tunnel, for Mach numbers from 0.4 to 1.4. Detailed effects of varying the angle of attack (up to 27 deg), angle of sideslip (-4 deg to +8 deg), Mach number, Reynolds number, and configuration buildup were investigated. In addition, the effects of wing trailing edge flap deflections, canard incidence, and vertical tail deflections were explored. Variable canard longitudinal location and different shapes of the inboard nacelle body strakes were also investigated.

Nelms, W. P.↗
NASA NTRS2016

Overview of Low-Speed Aerodynamic Tests on a 5.75% Scale Blended-Wing-Body Twin Jet Configuration

The NASA Environmentally Responsible Aviation (ERA) Project sponsored a series of computational and experimental investigations of the propulsion and airframe integration issues associated with Hybrid-Wing-Body (HWB) or Blended-Wing-Body (BWB) configurations. NASA collaborated with Boeing Research and Technology (BR&T) to conduct this research on a new twin-engine Boeing BWB transport configuration. The experimental investigations involved a series of wind tunnel tests with a 5.75-percent scale model conducted in two low-speed wind tunnels. This testing focused on the basic aerodynamics of the configuration and selection of the leading edge Krueger slat position for takeoff and landing. This paper reviews the results and analysis of these low-speed wind tunnel tests.

Vicroy, Dan D.↗
NASA NTRSDate not supplied

Evaluation of CFD Predictions of CobraMRV Control Surface Effectiveness at the NASA Langley Unitary Plan Wind Tunnel

The ability of CFD simulations to serve as a surrogate for wind tunnel testing at high supersonic speeds has been evaluated for a sub-scale model of the Co-Optimization Blunt-body Re-entry Analysis-Mid-lift-to-drag Rigid Vehicle (CobraMRV) human Mars entry vehicle concept. The vehicle was tested at the Unitary Plan Wind Tunnel (UPWT) at the NASA Langley Research Center under flow conditions and surface control configurations relevant to the entry stage of a flight mission. The CFD simulations were performed prior to gaining access to test results in order to assess how blind predictions obtained using best practices compare to experiments. Solutions of empty tunnel simulations were used as inflow boundary condition for the CobraMRV simulations in a truncated portion of the test section. Different solvers and turbulence models were used by separate teams to assess sensitivity to numerical methods, physics, and users. After release of the test results, the pre-test computations were compared to the experimental results, and additional analyses have been conducted to explain observed discrepancies. The amount of time and resources dedicated to each phase of the computational work was logged for comparison to that required for wind tunnel tests, and to inform planning of future CFD data base development projects.

ARMD↗
NASA NTRS1975

Acoustical modeling study of the open test section of the NASA Langley V/STOL wind tunnel

An acoustic model study was carried out to identify effective sound absorbing treatment of strategically located surfaces in an open wind tunnel test section. Also an aerodynamic study done concurrently, sought to find measures to control low frequency jet pulsations which occur when the tunnel is operated in its open test section configuration. The acoustical modeling study indicated that lining of the raised ceiling and the test section floor immediately below it, results in a substantial improvement. The aerodynamic model study indicated that: (1) the low frequency jet pulsations are most likely caused or maintained by coupling of aerodynamic and aeroacoustic phenomena in the closed tunnel circuit, (2) replacing the hard collector cowl with a geometrically identical but porous fiber metal surface of 100 mks rayls flow resistance does not result in any noticable reduction of the test section noise caused by the impingement of the turbulent flow on the cowl.

Ver, I. L.↗
NASA NTRS1993

Aerodynamic control of NASP-type vehicles through vortex manipulation, volume 4

Forebody Vortex Control (FVC) is an emerging technology that has received widespread and concentrated attention by many researchers for application on fighter aircraft to enhance aerodynamic controllability at high angles of attack. This research explores potential application of FVC to a NASP-type configuration. The configuration investigated is characterized by a slender, circular cross-section forebody and a 78 deg swept delta wing. A man-in-the-loop, six-degress-of-freedom, high-fidelity simulation was developed that demonstrates the implementation and advantages of pneumatic forebody vortex control. Static wind tunnel tests were used as the basis for the aerodynamic characteristics modeled in the simulation. Dynamic free-to-roll wind tunnel tests were analyzed and the wing rock motion investigated. A non-linear model of the dynamic effects of the bare airframe and the forebody vortex control system were developed that closely represented the observed behavior. Multiple state-of-the-art digital flight control systems were developed that included different utilizations of pneumatic vortex control. These were evaluated through manned simulation. Design parameters for a pneumatic forebody vortex control system were based on data collected regarding the use of blowing and the mass flow required during realistic flight maneuvers.

Smith, Brooke C.↗
NASA NTRSDate not supplied

The Multirotor Test Bed – A New NASA Test Capability for Advanced VTOL Rotorcraft Configurations

In November 2019, NASA completed the first wind tunnel test entry of the Multirotor Test Bed (MTB), a new test capability for advanced VTOL rotorcraft configurations. The MTB had been under development since 2017 when the need arose for an easily reconfigurable test stand for multirotor aircraft configurations. With the wide-ranging assortment of aircraft currently targeted at Urban Air Mobility and Unmanned Aircraft System applications, there is a need for validation data that will increase confidence in the computational modeling tools being used to develop these platforms. The MTB fills this need. This paper describes the key features of the MTB as well as its first wind tunnel test entry. A selection of results from the test is presented here, demonstrating the flexible configuration of the MTB and the types of data researchers can generate using this new test capability.

Multirotor Test Bed↗
NASA NTRS1985

The orbiter air data system

Air data parameters are required during Orbiter atmospheric entry for use by the autoguidance, navigation, and flight control systems, and for crew displays. Conventional aircraft calibrations of the Orbiter air data system were not practicable for the Space Shuttle, therefore extensive wind tunnel testing was required to give confidence in the preflight calibrations. Many challenges became apparent as the program developed; in the overall system design, in the wind tunnel testing program, in the implementation of the air data system calibration, and in the use of the flight data to modify the wind tunnel results. These challenges are discussed along with the methods used to solve the problems.

Hillje, E. R.↗
NASA NTRS2002

Modeling of UH-60A Hub Accelerations with Neural Networks

Neural network relationships between the full-scale, flight test hub accelerations and the corresponding three N/rev pilot floor vibration components (vertical, lateral, and longitudinal) are studied. The present quantitative effort on the UH-60A Black Hawk hub accelerations considers the lateral and longitudinal vibrations. An earlier study had considered the vertical vibration. The NASA/Army UH-60A Airloads Program flight test database is used. A physics based "maneuver-effect-factor (MEF)", derived using the roll-angle and the pitch-rate, is used. Fundamentally, the lateral vibration data show high vibration levels (up to 0.3 g's) at low airspeeds (for example, during landing flares) and at high airspeeds (for example, during turns). The results show that the advance ratio and the gross weight together can predict the vertical and the longitudinal vibration. However, the advance ratio and the gross weight together cannot predict the lateral vibration. The hub accelerations and the advance ratio can be used to satisfactorily predict the vertical, lateral, and longitudinal vibration. The present study shows that neural network based representations of all three UH-60A pilot floor vibration components (vertical, lateral, and longitudinal) can be obtained using the hub accelerations along with the gross weight and the advance ratio. The hub accelerations are clearly a factor in determining the pilot vibration. The present conclusions potentially allow for the identification of neural network relationships between the experimental hub accelerations obtained from wind tunnel testing and the experimental pilot vibration data obtained from flight testing. A successful establishment of the above neural network based link between the wind tunnel hub accelerations and the flight test vibration data can increase the value of wind tunnel testing.

UH-60A AIRCRAFT↗
NASA NTRS1982

The development of aerodynamic uncertainties for the Space Shuttle Orbiter

The methodology involved in developing the ability to reproduce aerodynamic results between various wind tunnel tests and to determine uncertainties due to differences between preflight aerodynamic predictions and flight results derived from analysis of past aircraft programs is presented. The uncertainties were developed for pitching moment, lateral-directional stability, rudder power, and aileron power, and were formulated to yield aerodynamic uncertainties for an orbital, manned first flight. The compressed development schedule required the aerodynamics results from wind tunnel tests be equipped with tolerances, which accounted for reasonable changes in the vehicle configuration. A worst case scenario was decided on, with the results that every prediction included the widest possible aerodynamic margins. Repeatibility was emphasized between wind tunnel model tests, and was achieved with an accuracy of 0.006 with inclusion of Reynolds effects.

Young, J. C.↗
NASA NTRS2001

Revalidation of the NASA Ames 11-by 11-Foot Transonic Wind Tunnel with a Commercial Airplane Model

The 11-By 11-Foot Transonic leg of the Unitary Plan Wind Tunnel (UPWT) was modernized to improve tunnel performance, capability, productivity, and reliability. Wind tunnel tests to demonstrate the readiness of the tunnel for a return to production operations included an Integrated Systems Test (IST), calibration tests, and airplane validation tests. One of the two validation tests was a 0.037-scale Boeing 777 model that was previously tested in the 11-By 11-Foot tunnel in 1991. The objective of the validation tests was to compare pre-modernization and post-modernization results from the same airplane model in order to substantiate the operational readiness of the facility. Evaluation of within-test, test-to-test, and tunnel-to-tunnel data repeatability were made to study the effects of the tunnel modifications. Tunnel productivity was also evaluated to determine the readiness of the facility for production operations. The operation of the facility, including model installation, tunnel operations, and the performance of tunnel systems, was observed and facility deficiency findings generated. The data repeatability studies and tunnel-to-tunnel comparisons demonstrated outstanding data repeatability and a high overall level of data quality. Despite some operational and facility problems, the validation test was successful in demonstrating the readiness of the facility to perform production airplane wind tunnel%, tests.

Kmak, Frank J.↗
NASA NTRSDate not supplied

Evaluation of CFD for Simulation of High-Supersonic Control Surface Effectiveness

This is the set of slides describing the CFD and wind-tunnel test studying the control surfaces of the CobraMRV concept for entry, descent, and landing on Mars. Difference between the CFD and wind-tunnel results are highlighted with the intent of showing whether CFD can replace wind-tunnel testing in the high supersonic flight regime.

wind tunnel↗
NASA NTRSDate not supplied

Requirements and Challenges for CFD Validation within the High-Lift Common Research Model Ecosystem

The High-Lift Common Research Model (CRM-HL) ecosystem is envisioned to become an industry standard set of test cases for high-lift aerodynamics prediction, with data generated providing a strong foundation for CFD validation. Since its original development, preliminary wind tunnel tests have been conducted to further understand and configure the geometry, and several more are in the planning phases. It is anticipated that the data generated in these tests will be used extensively by the CFD community for research, development, and validation of new techniques that yield more accurate results. To derive the maximum benefit from planned wind tunnel testing, data acquisition will be focused in several key areas to address specific shortcomings in CFD predictive capabilities. Significant challenges currently exist in areas including, but not limited to, characterizing high-lift flow phenomena, quantifying effects due to configuration changes, understanding wind tunnel and model installation effects, and establishing data uncertainty. This paper will discuss the current state-of-the-art in high-lift CFD prediction, key limitations of current CFD methods and tools, establishing a validation dialog between test and CFD practitioners, and the flow phenomena of highest interest, in an effort to begin to address these challenges. To this end, it is expected that the data generated from CRM-HL tests will form a strong foundation for future predictive capability.

Adam M Clark↗
NASA NTRS1979

XV-15 Tilt Rotor Research Aircraft - Program report

This paper is a status report of the NASA/Army XV-15 Project. The basic tilt-rotor concept and the XV-15 Tilt-Rotor Research Aircraft are discussed and some results of full-scale wind-tunnel tests in the Ames 40- by 80-Foot Wind Tunnel are presented. Flight-test data are included to give preliminary performance, noise, and vibration data in hover and as far into transition flight as are available at the time of presentation. Information concerning vehicle aerodynamics and airloads obtained as a result of both wind-tunnel and flight tests are provided with some conclusions as to the ramifications of the data in terms of design criteria and configuration layout.

Magee, J. P.↗