Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “voltage stability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Elimination of the bias-stress effect in ligand-free quantum dot field-effect transistors

Field-effect transistors (FETs) made from colloidal quantum dot (QD) solids commonly suffer from current–voltage hysteresis caused by the bias-stress effect (BSE), which complicates fundamental studies of charge transport in QD solids and the use of QD FETs in electronics. Here, we show that the BSE can be eliminated in n-channel PbSe QD FETs by first removing the QD ligands with a dose of H 2 S gas and then infilling the QD films with alumina by atomic layer deposition (ALD). The H 2 S-treated, alumina-infilled FETs have stable, hysteresis-free device characteristics (total short-term stability), indefinite air stability (total long-term stability), and a high electron mobility of up to 14 cm 2 V −1 s −1 , making them attractive for QD circuitry and optoelectronic devices. The BSE-free devices are utilized to conclusively establish the dependence of the electron mobility on temperature and QD diameter. We demonstrate that the BSE in these devices is caused by both electron trapping at the QD surface and proton drift within the film. The H 2 S/alumina chemistry produces ligand-free PbSe/PbS/Al 2 O 3 interfaces that lack the traps that cause the electronic part of the BSE, while full alumina infilling stops the proton motion responsible for the ionic part of the BSE. In conclusion, our matrix engineering approach should aid efforts to eliminate the BSE, boost carrier mobilities, and improve charge transport in other types of nanocrystal solids.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Significant Improvements to Si Calendar Lifetime Using Rapid Electrolyte Screening via Potentiostatic Holds

Silicon-based lithium-ion batteries exhibit severe time-based degradation resulting in poor calendar lives. This has been identified as the major impediment towards commercialization with cycle life considered a solved issue through nanosizing and protective coatings allowing over 1000 cycles of life to be achieved. In this work, rapid screening of sixteen electrolytes for calendar life extension of Si-rich systems (70 wt% Si) is performed using the voltage hold (V-hold) protocol. V-hold significantly shortens the testing duration over the traditional open circuit voltage reference performance test allowing us to screen electrolytes within a span of two months. We find a novel ethylene carbonate (EC) free electrolyte formulation containing lithium hexafluorophosphate (LiPF 6 ) salt, and binary solvent mix of fluoroethylene carbonate (FEC), ethyl methyl carbonate (EMC) that extends calendar life of Si cells as compared to conventional EC based electrolyte. Our coupled experimental-theoretical analysis framework provides a decoupling of the parasitic currents during V-hold, allowing us to extrapolate the capacity loss to predict semiquantitative calendar lifetimes. Subsequently, cycle aging and oxidative stability tests of the EC free system also show enhanced performance over baseline electrolyte.

25 ENERGY STORAGE↗
DOE OSTI2023

Communication-Constrained Robust Control and Learning of Grid-Connected

The electric grid of things (EGoT) promises great potential for innovative grid services by tapping into vast load flexibility. However, the unique characteristics of EGoT, being a part of the cyber-physical electric power system, present both opportunities and challenges, especially concerning supply-demand balancing, stability, and communication constraints. Traditionally, centralized control was employed to ensure balance and stability in power systems. However, with the massive influx of EGoT devices, new strategies are needed to efficiently coordinate and control these distributed devices for optimal grid operations. While some studies have explored efficiency and economic models, there remains a gap in ensuring reliability under everyday operations and resilience during extreme conditions. Addressing this gap, this project develops the technology for an Energy Service Interface (ESI) that includes novel pricing, control, learning, and distributed optimization algorithms, which will enable utilities to recruit EGoT assets for crucial grid services such as load flexibility, voltage regulation, and situation-awareness. The key novelty of the proposed technology is the careful distribution of learning and control functions across utility and EGoT asset owners such that provably efficient and resilient grid operations are attained while respecting communication and information-exchange constraints. Specifically, the project team develops machine-learning enhanced load modeling methods to allow EGoT asset owners to learn their load capability and flexibility, and develops pricing-based and decentralized learning-based control so that asset owners can coordinate to meet system-wide demand-supply balance and reliability goals. For extreme situations involving high-impact, low-probability catastrophic events (termed the “black-sky” events), the team also develops (1) a “Feeder-Operating Center-on-a-Laptop” (FOCAL) software that can assist utility personnel in leveraging EGoT assets to accelerate the service recovery of damaged feeders, and (2) distributed optimization algorithms that can coordinate the operation points of EGoT devices under severe communication constraints. The proposed technology has been extensively tested and evaluated through simulations and on a testbed. In summary, as we transition into a more interconnected and digital power grid era, our project’s findings and developments offer a pivotal step toward guaranteeing both efficiency and resilience in the face of both everyday operations and rare “black-sky” events.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2020

A 3D porous honeycomb carbon as Na-ion battery anode material with high capacity, excellent rate performance, and robust stability

Motivated by the synthesis of three-dimensional (3D) honeycomb carbon structures and the subsequent theoretical prediction of an energetically more favorable hexagonal carbon phase composed of 28 carbon atoms in the unit cell (hC28) with ordered pores, excellent mechanical properties, and metallic feature, we explore its potential for a Na-ion battery (NIB) anode material. Using density functional theory based calculations, we find that hC28 is a promising candidate whose specific capacity of 717 mAh/g is almost three times larger than that of hard carbon (~250 mAh/g). In addition, migration barrier of Na ions along the honeycomb channel is only 0.08 eV and the volume change during the charging/discharging process is merely 2.30%, which are much less than those of other carbon-based NIB anode materials. The average voltage is also low (0.36 eV) which can provide high operating voltage when connected to the cathode. Finally, these encouraging results would pave the way towards the development of hC28 as NIB anode with high capacity, excellent rate performance, low open-circuit voltage, and long-term cycle life.

36 MATERIALS SCIENCE↗
DOE OSTI2023

First-Principles Examination of Multiple Criteria of Organic Solvent Oxidative Stability in Batteries

Oxidative instability of the liquid electrolyte at or near battery cathode oxide surfaces has significant detrimental effects on batteries. Organic solvent molecules are often the fuel and precursors of such degradation processes, releasing electrons and protons that react with cathode oxides and electrolyte anions. These reactions contribute to cathode–electrolyte interphase (CEI) film formation, transition-metal ion dissolution, and phase transformation of the surface regions of the cathode. Here we apply density functional theory calculations to examine four criteria of oxidative stability (oxidation potential, hydrogen removal energies, and initial reactivity on two types of oxide facets) using four different solvent/additive molecules (ethylene carbonate, fluoroethylene carbonate, 1,3-dioxolane, and dimethyl ether). The ranking of molecular stability differs with each criterion. Surprisingly, the all-oxygen-terminated basal planes of layered oxides exhibit lower reaction barriers than spinel surface facets with exposed transition-metal cations, especially for ether solvents; the calculations also suggest basal planes contribute to the dissolution of transition-metal ions. Further, the structure–degradation relation complexity underscores the challenge of understanding the function of the CEI but also offers a guide to future degradation-mitigation strategies including facet engineering. Our predictions and models help establish a framework for future studies relevant to high-voltage conditions.

25 ENERGY STORAGE↗
DOE OSTI2020

Perovskite Solar Cells with Enhanced Fill Factors Using Polymer-Capped Solvent Annealing

Despite huge improvements in power conversion efficiencies of perovskite solar cells, the technology is still limited by fill factors at around 80%. In this work, we report perovskite solar cells having exceptionally high fill factors of 85% and enhanced open-circuit voltage without sacrificing short-circuit current through a polymer-capped solvent-annealing process assisted by a hot air blower. Additionally, during the solvent-annealing, the perovskite surface flattens and the perovskite grains agglomerate into micrometer-sized clusters having enlarged α-phase crystallites, while the δ-phase simultaneously disappears. The optimized structure reduces energetic disorder and trap-assisted recombination in the perovskite layer, resulting in an enhanced efficiency from 18.2% to 19.8% and improved device lifetime. Our results provide a pathway to increase the device efficiency and stability of perovskite solar cells, and have the potential to stimulate research on scalable poly-crystal perovskite layer fabrication in optoelectronic devices.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2024

Dynamic response of nanosecond repetitively pulsed discharges to combustion dynamics: regime transitions driven by flame oscillations

Abstract When using nanosecond repetitively pulsed discharges to actuate on dynamic combustion instabilities, the environment the discharge is created in is unsteady and changing on the timescale of the combustion processes. As a result, individual discharge pulses are triggered in a background gas that evolves at the timescale of combustion dynamics, and pulse-to-pulse variations may be observed during the instability cycle. Prior work has studied nanosecond pulsed discharges in pin-to-ring configurations used to control instabilities in lean-operating swirl-stabilized combustors, and observed variable discharge behavior. The focus of this work is on characterizing how the pulse-to-pulse discharge morphology, energy deposition, and actuation authority, evolve during the combustion instability cycle. This has important implications for designing effective plasma-assisted combustion control schemes. The discharge is observed in two distinct modes, a streamer corona and a nanosecond spark, with the occurrence of each regime directly linked to the phase of the combustor instability. Variation of pulse repetition frequency affects the total fraction of pulses in each mode, while variation of voltage affects the onset of the nanosecond spark mode. The transitions are described in terms of ratios of the relevant combustion and plasma timescales and the implications of this coupled interaction on the design of an effective control scheme is discussed.

Physics↗
DOE OSTI2022

Lithiation-Induced Defect Engineering to Promote Oxygen Evolution Reaction

Exploring efficient electrocatalysts for oxygen evolution reaction (OER) is an urgent need to advance the development of sustainable energy conversion. Though defect engineering is considered an effective strategy to regulate catalyst activity for enhanced OER performance, the controllable synthesis of defective oxides electrocatalysts remains challenging. Here, oxygen defects are introduced into NiCo 2 O 4 nanorods by an electrochemical lithiation strategy. By tuning in situ lithiation potentials, the concentration of oxygen defects and the corresponding catalytic activity can be feasibly regulated. In addition, the relationship between the changes in the defect density and electronic structure and the lithiation cut-off voltages is revealed. The results show that NiCo 2 O 4 nanorods undertook intercalation and two-step conversion reaction, in which the lithiation-induced conversion reaction gives rise to a CoO@NiO-based structure with higher defect density and lower oxidation states. As a result, the defective CoO@NiO-based catalyst exhibits exceptional OER activity with an overpotential of 270 mV at 10 mA cm -2 , which is about 74 mV below the pristine nanomaterials. In conclusion, this research proposes a novel strategy to explore high-performance catalysts with structural stability and defect control.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Rational optimization of substituted α–MnO 2 cathode for aqueous zinc–ion battery

Density functional theory (DFT) is utilized to explore the effects of increasing concentrations of vanadium (V) and chromium (Cr) substitution on the discharge of α-MnO 2 cathode in hydrated zinc-ion batteries (ZIBs). During H + -intercalation and Zn 2+ -intercalation, Cr-substitution proves to be more effective than V-substitution in promoting discharge behaviors. Transitioning from Mn 0.875 Cr 0.125 O 2 , Mn 0.75 Cr 0.25 O 2 to Mn 0.625 Cr 0.375 O 2 is found to consistently enhance the discharge voltage, along with improved tunnel structure retention and volume expansion suppression. In comparison, the promoting effect of increasing V-substitution is relatively small at initial discharge stages and leads to degradation at later stages, primarily due to an increased concentration of unstable Mn 2+ ion. The superior effect of Cr-substitution is attributed to the unique atomic and electronic structures of substituted Cr 4+ and reduced Cr 3+ ions during discharge. These ions serve as active electron acceptors to limit the formation of Mn 3+ and Mn 2+ ions, and as anchors to stabilize the α-MnO 2 framework and intercalated H + /Zn 2+ ions, respectively. Finally, our study highlights fine-tuning through substitution to enhance the performance of α-MnO 2 -based cathode materials in ZIBs.

25 ENERGY STORAGE↗
DOE OSTI2023

Efficient Reversible Operation and Stability of Novel Solid Oxide Cells

This project aims to develop and test novel Reversible Solid Oxide Cells (ReSOCs) specifically designed to yield low area specific resistance, as required to achieve high round trip efficiency in reversible operation at high current density. A key objective is to improve long-term reversible SOC durability; mechanistic degradation models will be used to predict long-term durability using input data from accelerated testing that combines electrochemical life testing with quantitative microstructural and chemical evaluation. The modeling tasks seek to design low-loss, low-cost ReSOC systems using input data from the experimental cell studies. A key challenge is to develop a thermal management strategy that maintains thermally self-sustaining operation while operating the stack at a potential lower than the thermo-neutral steam electrolysis voltage of ~1.3 V, to maintain high efficiency.

08 HYDROGEN↗
DOE OSTI2023

Free‐Standing α‐MoO 3 / Ti 3 C 2 MXene Hybrid Electrode in Water‐in‐Salt Electrolytes

While transition‐metal oxides such as α‐MoO 3 provide high capacity, their use is limited by modest electronic conductivity and electrochemical instability in aqueous electrolytes. Two‐dimensional (2D) MXenes, offer metallic conductivity, but their capacitance is limited in aqueous electrolytes. Insertion of partially solvated cations into Ti 3 C 2 MXene from lithium‐based water‐in‐salt (WIS) electrolytes enables charge storage at positive potentials, allowing a wider potential window and higher capacitance. Herein, we demonstrate that α‐MoO 3 /Ti 3 C 2 hybrids combine the high capacity of α‐MoO 3 and conductivity of Ti 3 C 2 in WIS (19.8 m LiCl) electrolyte in a wide 1.8 V voltage window. Cyclic voltammograms reveal multiple redox peaks from α‐MoO 3 in addition to the well‐separated peaks of Ti 3 C 2 in the hybrid electrode. This leads to a higher specific charge and a higher rate capability compared to a carbon and binder containing α‐MoO 3 electrode. These results demonstrate that the addition of MXene to less conductive oxides eliminates the need for conductive carbon additives and binders, leads to a larger amount of charge stored, and increases redox capacity at higher rates. In addition, MXene encapsulated α‐MoO 3 showed improved electrochemical stability, which was attributed to the suppressed dissolution of α‐MoO 3 . The work suggests that oxide/MXene hybrids are promising for energy storage.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Amorphous ZrCl 4 -Based Superionic Conductor as a Cost-Effective Solid Electrolyte for Batteries

Developing highly conductive and cost-effective solid electrolytes is essential for the commercialization of all-solid-state batteries (ASSBs). Zr-based halide electrolytes hold great promise due to their low estimated cost and high oxidation stability. However, the ionic conductivities of most of them are not high enough to enable moderate- and high-rate cycling of ASSBs. Here, fast ion transport is achieved in a group of cost-effective ZrCl 4 -based electrolytes via a design strategy to create highly disordered amorphous structures. Amorphous Li 0.8 ZrCl 4 (SO 4 ) 0.4 , with a low estimated cost of $21 kg –1 , achieves an ionic conductivity of 1.86 mS cm –1 at 25 °C. It also shows a high oxidation limit of 4.5 V vs Li/Li + and good compatibility with high-voltage cathodes, as demonstrated by the stable cycling of ASSBs (73.7% capacity retention after 1000 cycles at 1 C). Synchrotron X-ray diffraction, pair distribution function analysis, and electrochemical impedance spectroscopy reveal that the outstanding conductivity of these amorphous electrolytes is closely related to their short-range and medium-range ordering, revealing new insights for designing high-performance, cost-effective solid electrolytes.

Zhang, Guangxing [Georgia Institute of Technology,↗
DOE OSTI2024

Application of a Comprehensive Lagrangian–Eulerian Spark-Ignition Model to Different Operating Conditions

Increasing engine efficiency is essential to reducing emissions, which is a priority for automakers. Unconventional modes such as boosted and highly dilute operation have the potential to increase engine efficiency but suffer from stability concerns and cyclic variability. To aid engineers in designing ignition systems that reduce cyclic variability in such engine operation modes, reliable and accurate spark-ignition models are necessary. Here, in this article, a Lagrangian–Eulerian spark-ignition (LESI) model is used to simulate electrical discharge, spark channel elongation, and ignition in inert or reacting crossflow within a combustion vessel, at different pressures, flow speeds, and dilution rates. First the model formulation is briefly revisited. Then, the experimental and simulations setups are presented. The results showcase the model’s ability to predict the secondary circuit voltage, current, and power signals, in addition to the spark channel elongation, for the inert cases, or flame front growth, for the reacting cases. The results also compare simulation spark channel and flame growth plots to experimental Schlieren images at different instants in time. This work serves to highlight LESI’s ability to predict the characteristics of discharge and ignition across a variety of operating conditions.

42 ENGINEERING↗
DOE OSTI2024

Fast spark-detection system for GEM detectors

The sPHENIX experiment is currently under commissioning at the Relativistic Heavy Ion Collider (RHIC) at Brookhaven National Lab (BNL). The Time Projection Chamber (TPC) serves as a tracking detector for the experiment. The sPHENIX TPC uses a stack of four Gas Electron Multipliers (GEMs) as a gain stage in a reduced ion back-flow configuration. To mitigate the damaging effects of sparks in the GEMs, an online spark monitoring system was created. Once the system detects a spark in a GEM stack, the voltages across the GEMs in that stack can be lowered to prevent further sparking without affecting the gain and efficiency of the other modules. Spark signals are coupled out of the GEM stack by a pick-off capacitor attached to the bottom of the bottom GEM. Custom PCBs convert the oscillatory spark signal into a mono-polar pulse that is then digitized. The software then saves the waveform in a server and uses experimentally derived thresholds to determine how to react. As a result, the system has so far proven to be effective at improving the stability of the TPC and preventing damaging events while collecting cosmic ray data.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2024

RePED 250: A Revolutionary, High Drilling Rate, High-T Geothermal Drilling System and Companion Power Electronics

Geothermal drilling in the United States is drastically slower and more costly than Oil and Gas (O&G) drilling, primarily due to the additional challenges in geothermal wells: hard rock types and high temperatures. The Repetitive Pulsed Electric Drill (250°C) (RePED-250), developed by Tetra Corporation has the potential to change this with a novel electro-crushing technology. RePED-250 releases pulses of electricity through the rock, which causes it to break in tension, instead of compression like conventional rotary drilling. The tensile strength of hard rocks like granite is only ~5% of their compressive strength, requiring less energy, time, and wear on the bit compared to conventional drilling. The RePED drill bit has no moving parts, uses drilling mud to remove rock fragments, and uses standard drill pipe, enabling a direct transition from conventional drilling systems. The objective of this project is to move RePED technology towards commercial readiness for high-temperature geothermal applications. This involves: 1) Creating high-temperature, high power electronic components for the RePED drill capable of operating at the high temperatures of a geothermal well. The target is a 250°C ambient environment. Specifically, capacitors, high voltage switches, and a downhole generator capable of generating the necessary power. 2) Demonstrating RePED’s effectiveness drilling through hard rock (granite) and examining its pathway to commercialization and effect on the US geothermal market. Work on this project has led to significant improvement over the state-of-the-art for all the examined electronics, through design, modeling, and testing of these novel components, though some additional development is still needed to deploy these high-temperature parts in a geothermal well. Besides their use in RePED-250, each component has applications in other industries where the stability of electronics at high-temperature is needed. To address the second barrier to commercialization, a 9” hole was drilled through a sample block of granite, demonstrating the tool’s effectiveness in hard rock. The team investigated RePED-250’s effect on well cost and the geothermal industry, through various techno-economic models described in the report.

15 GEOTHERMAL ENERGY↗
DOE OSTI2024

RePED 250: A Revolutionary, High Drilling Rate, High-T Geothermal Drilling System and Companion Power Electronics (Final Report)

Geothermal drilling in the United States is drastically slower and more costly than Oil and Gas drilling, primarily due to the additional challenges in geothermal wells: hard rock types and high temperatures. The Repetitive Pulsed Electric Drill (250 degrees C) (RePED-250), developed by Tetra Corporation has the potential to change this with a novel electro-crushing technology. RePED-250 releases pulses of electricity through the rock, which causes it to break in tension, instead of compression like conventional rotary drilling. The tensile strength of hard rocks like granite is only ~5% of their compressive strength, requiring less energy, time, and wear on the bit than conventional drilling. The RePED drill bit has no moving parts, uses drilling mud to remove rock fragments, and standard drill pipe, enabling a direct transition from conventional drilling systems. The objective of this project is to move RePED technology towards commercial readiness for high-temperature geothermal applications. This involves: 1) Creating high-temperature, high power electronic components for the RePED drill capable of operating at the high temperatures of a geothermal well. The target is a 250 degrees C ambient environment. Specifically, capacitors, high voltage switches, and a downhole generator capable of generating the necessary power. 2) Demonstrating RePED's effectiveness drilling through hard rock (granite) and examining its pathway to commercialization and effect on the US geothermal market. Work on this project has led to significant improvement over the state-of-the-art for all the examined electronics, through design, modeling, and testing of these novel components, though some additional development is still needed to deploy these high-temperature parts in a geothermal well. Besides their use in RePED-250, each component has applications in other industries where the stability of electronics at high-temperature is needed. To address the second barrier to commercialization, a 9" hole was drilled through a sample block of granite, demonstrating the tool's effectiveness in hard rock. The team investigated RePED-250's effect on well cost, and the geothermal industry, through various models described in the report.

15 GEOTHERMAL ENERGY↗
DOE OSTI2020

Hybrid EMT-TS Simulation Strategies to Study High Bandwidth MMC-Based HVdc Systems

Modular multilevel converters (MMCs) are widely used in the design of modern high-voltage direct current (HVdc) transmission system. High-fidelity dynamic models of MMCs-based HVdc system require small simulation time step and can be accurately modeled in electro-magnetic transient (EMT) simulation programs. The EMT program exhibits slow simulation speed and limitation on the size of the model and brings certain challenges to test the high-fidelity HVdc model in system-level simulations. This paper presents the design and implementation of a hybrid simulation framework, which enables the co-simulation of the EMT model of Atlanta-Orlando HVdc line and the transient stability (TS) model of the entire Eastern Interconnection system. This paper also introduces the implementation of two high-fidelity HVdc line models simulated at different time steps and discusses a dedicated method for sizing the buffer areas on both sides of the HVdc line. The simulation results of the two HVdc models with different sizes of buffer areas are presented and compared.

Liu, Yuan↗
DOE OSTI2022

Electrochemically induced amorphous-to-rock-salt phase transformation in niobium oxide electrode for Li-ion batteries

Intercalation-type metal oxides are promising negative electrode materials for safe rechargeable lithium-ion batteries due to the reduced risk of Li plating at low voltages. Nevertheless, their lower energy and power density along with cycling instability remain bottlenecks for their implementation, especially for fast-charging applications. Here, we report a nanostructured rock-salt Nb 2 O 5 electrode formed through an amorphous-to-crystalline transformation during repeated electrochemical cycling with Li + . This electrode can reversibly cycle three lithiums per Nb 2 O 5 , corresponding to a capacity of 269 mAh g –1 at 20 mA g –1 , and retains a capacity of 191 mAh g –1 at a high rate of 1 A g –1 . Further, it exhibits superb cycling stability with a capacity of 225 mAh g –1 at 200 mA g –1 for 400 cycles, and a Coulombic efficiency of 99.93%. We attribute the enhanced performance to the cubic rock-salt framework, which promotes low-energy migration paths. Our work suggests that inducing crystallization of amorphous nanomaterials through electrochemical cycling is a promising avenue for creating unconventional high-performance metal oxide electrode materials.

25 ENERGY STORAGE↗