Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “structural material”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Femto-second Laser’s Enabling New Length Scale Fabrications for Rapid Post Irradiation Examination of Materials: Concluding LDRD Project Poster

Mechanical testing campaigns are required to qualify materials for advanced reactor conditions, yet economical and safety limitations restrict the number of standardized mechanical tests that can be performed. Reducing the size of the sample is one approach to addressing these challenges and to accelerating testing. Previous research has shown that smaller mechanical test samples produce higher yield and ultimate stress values compared to values measured from standard sample sizes: the “smaller is stronger” effect. Specimens used in accelerated material testing campaigns must reflect bulk material performance to enable engineering scale material property measurement. The objective of this research project was to determine if engineering scale mechanical behavior—the yield stress—could be measured with micro-tensile test samples smaller than traditional standard testing geometries. The relationship between yield stress and sample size was explored with two different nuclear-relevant structural materials: Zircaloy-4 and tungsten. Mechanical testing of both metals demonstrated decreasing yield stress values with increasing sample gauge size across three different sizes. Yield stress values from the largest gauge size, fabricated with a femto-second laser ablation system, approach bulk material yield stress values reported in published literature. Preliminary analysis of the tungsten samples indicates the yield stress value depends on the grain characteristics within the gauge section, in addition to the gauge size. Accompanying modeling efforts, including response surface generation and crystal plasticity approaches, further demonstrated that the size of the sample gauge section alone cannot explain the change in yield stress values.

36 MATERIALS SCIENCE↗

Ferrocene-Promoted Long-Cycle Lithium-Sulfur Batteries

Confining lithium polysulfide intermediates is one of the most effective ways to alleviate the capacity fade of sulfur-cathode materials in lithium–sulfur (Li–S) batteries. To develop long-cycle Li–S batteries, there is an urgent need for material structures with effective polysulfide binding capability and well-defined surface sites; thereby improving cycling stability and allowing study of molecular-level interactions. This challenge was addressed by introducing an organometallic molecular compound, ferrocene, as a new polysulfide-confining agent. With ferrocene molecules covalently anchored on graphene oxide, sulfur electrode materials with capacity decay as low as 0.014 % per cycle were realized, among the best of cycling stabilities reported to date. With combined spectroscopic studies and theoretical calculations, it was determined that effective polysulfide binding originates from favorable cation–π interactions between Li + of lithium polysulfides and the negatively charged cyclopentadienyl ligands of ferrocene.

25 ENERGY STORAGE↗

Selective laser sintering of MA956 oxide dispersion strengthened steel

Oxide Dispersion Strengthened (ODS) steels’ qualities of radiation damage resistance and high strength at high temperature make them promising nuclear structural materials. However, the dispersed yttria that gives ODS steel its beneficial qualities are generally compromised during joining processes, making fabrication difficult and expensive. The selective laser sintering process offers a potential path through this barrier by which net-shape parts can feasibly be built via additive manufacturing without fully melting the structure. By rastering a 400 W laser over a MA956 ODS steel powder bed, here we additively built parts with varying build conditions. Although density was achieved to within 97% of the wrought MA956, ultimate tensile strengths achieved only 65% of the wrought strength. Spectroscopy analysis points to the agglomeration of the yttria nano-particles as a possible explanation for the loss in strength. Further study might benefit from exploration of other parameters such as thinner powder build layers which would require less energy input to achieve sintering while minimizing time above the melting temperature.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Adaptive Machine Learning for Bragg Coherent Diffraction Imaging (BCDI) of 3D Electron Density Maps with Application to La 2-x Ba x CuO 4 (LBCO) High Temperature Superconductor Studies [PowerPoint]

Understanding mesoscale heterogeneity is important for evaluating fatigue and failure of structural materials and for manufacturing processes. Data-driven tools can facilitate in guiding effort investment (measurements and computations) at various stages of the materials development. Our 3D reconstruction approach is to find a set of coefficients which define a bounding surface of the electron density. Data for training the 3D CNN was generated by sampling coefficients from uniform distributions. Test vs. prediction values are shown for the 28 even-valued coefficients for 1000 test structures, with the best and worst performers highlighted. The adaptive part of this work utilized a model independent extremum seeking (ES). The predictions of the CNN were used as the starting point for the ES algorithm. The convergence of the ES algorithm for 3 different structures is illustrated, and the robustness of the adaptive ML approach was demonstrated on experimentally measured 3D crystal from high energy diffraction microscopy. Reconstruction of a non-uniform density volume with different levels of Poisson noise is also shown. Preliminary attempts at reconstructing measured La 2-x Ba x CuO 4 diffraction patterns have so far failed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Nonlinear Dynamic Properties of Layered Composite Materials

We present an application of the asymptotic homogenization method to study wave propagation in a one-dimensional composite material consisting of a matrix material and coated inclusions. Physical nonlinearity is taken into account by considering the composite's components as a Murnaghan material, structural nonlinearity is caused by the bonding condition between the components.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Thermo-structural design of the European DEMO water-cooled blanket with a multiscale-multiphysics framework

The Water-Cooled Lithium-Lead (WCLL) blanket concept is one of four possible embodiments under consideration for the European Demonstration Power Plant DEMO, beyond ITER. It is based on a water-cooled first wall and blanket structure with the RAFMS (Reduced Activation Ferritic/Martensitic Steel, Eurofer 97) as structural material and PbLi as neutron multiplier and tritium breeder. We first develop a multiphysics modeling framework in order to optimize the design and achieve long blanket lifetime, maintainability, and high reliability. The approach is demonstrated by coupling Computational Fluid Dynamics (CFD), heat transfer and solid mechanics. The multiphysics framework is then utilized to provide the loading conditions for a multiscale design approach particularly focused on modeling the effects of both steady-state and operational transients on the structural integrity of the First Wall (FW). The methodology builds on the ITER Structural Design Criteria for In-Vessel Components (ISDC-IC), then extending the criteria to progressively incorporate continuum plasticity models and microstructure-based representation of deformation and fracture. We finally introduce advanced fracture mechanics concepts based on a Materials-Specific Failure Assessment Diagram (MS-FAD), in which precise calculations of the J-integral of an elasto-plastic material is required. This is especially important for the water-cooled design because of the limited fracture toughness of Eurofer 97 below 300 °C. The methodology has been applied to screen the FW/Blanket performance of a range of steady state heat flux assumed to be applied during the plasma pulse flat top, and up to 0.8 MW/m 2 . It has become clear that the radiation steady state load will be lower than the values screened here, while the local heat flux due to particle loads will lead to global higher values than the values investigated here. The methodology will be further fine-tuned to specific loading conditions in order to assess actual performance limits of the DEMO WCLL BB.

European DEMO↗

Machine learning in nuclear materials research

Nuclear materials are often demanded to function for extended time in extreme environments, including high radiation fluxes with associated transmutations, high temperature and temperature gradients, mechanical stresses, and corrosive coolants. They also have a wide range of microstructural and chemical makeups, resulting in multifaceted and often out-of-equilibrium interactions. Machine learning (ML) is increasingly being used to tackle these complex time-dependent interactions and aid researchers in developing models and making predictions, sometimes with better accuracy than traditional modeling that focuses on one or two parameters at a time. Conventional practices of acquiring new experimental data in nuclear materials research are often slow and expensive, limiting the opportunity for data-centric ML, but new methods are changing that paradigm. Here we review high-throughput computational and experimental data approaches, especially robotic experimentation and active learning that is based on Gaussian process and Bayesian optimization. We show ML examples in structural materials (e.g., reactor pressure vessel (RPV) alloys and radiation detecting scintillating materials) and highlight new techniques of high-throughput sample preparation and characterizations, and automated radiation/environmental exposures and real-time online diagnostics. Herein, this review suggests that ML models of material constitutive relations in plasticity, damage, and even electronic and optical responses to radiation are likely to become powerful tools as they develop. Finally, we speculate on how the recent trends of using natural language processing (NLP) to aid the collection and analysis of literature data, interpretable artificial intelligence (AI), and the use of streamlined scripting, database, workflow management, and cloud computing platforms that will soon make the utilization of ML techniques as commonplace as the spreadsheet curve-fitting practices of today.

36 MATERIALS SCIENCE↗

Tailoring Local Chemical Ordering via Elemental Tuning in High-Entropy Alloys

Due to the large multi-elemental space desired for property screening and optimization, high-entropy alloys (HEAs) hold greater potential over conventional alloys for a range of applications, such as structural materials, energy conversion, and catalysis. However, the relationship between the HEA composition and its local structural/elemental configuration is not well understood, particularly in noble-metal-based HEA nanomaterials, hindering the design and development of nano-HEAs in energy conversion and catalysis applications. In this work, we determined precise atomic-level structural and elemental arrangements in model HEAs composed of RhPtPdFeCo and RuPtPdFeCo to unveil their local characteristics. Notably, by changing just one constituent element in the HEA (Rh to Ru), we found dramatic changes in the elemental arrangement from complete random mixing to a local single elemental ordering feature. Additionally, we demonstrate that the local ordering in RuPtPdFeCo can be further controlled by varying the Ru concentration, allowing us to toggle between local Ru clustering and distinct heterostructures in multicomponent systems. Overall, our study presents a practical approach for manipulating local atomic structures and elemental arrangements in noble-metal-based HEA systems, which could provide in-depth knowledge to mechanistically understand the functionality of noble-metal-based HEA nanomaterials in practical applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Delayed Gamma Measurements in Different Nuclear Research Reactors Bringing Out the Importance of the Delayed Contribution in Gamma Flux Calculations

Neutron and gamma flux levels are key parameters in nuclear research reactors. In Material Testing Reactors, such as the future Jules Horowitz Reactor, under construction at the French Alternative Energies and Atomic Energy Commission (CEA Cadarache, France), the expected gamma flux levels are very high (nuclear heating is of the order of 20 W/g at 100 MWth). As gamma rays deposit their energy in the reactor structures and structural materials it is important to take them into account when designing irradiation devices. There are only a few sensors which allow measurements of the nuclear heating ; a recent development at the CEA Cadarache allows measurements of the gamma flux using a miniature ionization chamber (MIC). The measured MIC response is often compared with calculation using modern Monte Carlo (MC) neutron and photon transport codes, such as TRIPOLI-4 and MCNP6. In these calculations only the production of prompt gamma rays in the reactor is usually modelled thus neglecting the delayed gamma rays. Hence calculations and measurements are usually in better accordance for the neutron flux than for the gamma flux. In this paper we study the contribution of delayed gamma rays to the total MIC signal in order to estimate the systematic error in gamma flux MC calculations. In order to experimentally determine the delayed gamma flux contributions to the MIC response, we performed gamma flux measurements with CEA developed MIC at three different research reactors: the OSIRIS reactor (MTR - 70 MWth at CEA Saclay, France), the TRIGA MARK II reactor (TRIGA - 250 kWth at the Jozef Stefan Institute, Slovenia) and the MARIA reactor (MTR - 30 MWth at the National Center for Nuclear Research, Poland). In order to experimentally assess the delayed gamma flux contribution to the total gamma flux, several reactor shut down (scram) experiments were performed specifically for the purpose of the measurements. Results show that on average about 30 % of the MIC signal is due to the delayed gamma rays. In this paper we describe experiments in each of the three reactors and how we estimate delayed gamma rays with MIC measurements. The results and perspectives are discussed. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Characterisation of synthesised nickel and cobalt nanoscale oxides

The special features of nano-structured materials have been motivating the search for new synthesis methods for these types of materials. This paper is primarily focused on the characterisation of nickel and cobalt nanoscale oxides synthesised by a method based on the dehydration of their respective metal nitrate solutions. This chemical-based synthesis route is briefly described, and basic thermodynamic arguments are presented to theoretically support the feasibility of obtaining such oxides. In addition, a very homogeneous co-formed Ni and Co oxide compound was obtained by dehydrating a water-based solution of both nitrates. Characterisation was done with by X-ray diffraction and transmission electron microscopy, which revealed, respectively, the presence of oxides and their nanoscale structures, including particle morphology and size distribution. High-resolution electron microscopy (HREM) images indicated that the average particle sizes of the obtained NiO and Co{sub 3}O{sub 4} obtained were approximately 20 nm and 40 nm, respectively. In addition, some particles presented crystalline defects in their inner structure, although those smaller than 5 nm seemed to be defect-free and were spherical or faceted. In addition to being characterised as nano-particle-bearing materials, the co-formed oxides can also be used as the starting material for alloys and nano-composites preparations if they are submitted to complete or partial reduction, respectively. - Highlights: Black-Right-Pointing-Pointer The feasibility in obtaining Ni and Co and their co-formed oxides was evaluated. Black-Right-Pointing-Pointer Ni, Co and Ni and Co co-formed nanostructured oxides were synthesised by the route. Black-Right-Pointing-Pointer XRD, TEM and HREM techniques were used to characterise the obtained nanostructures. Black-Right-Pointing-Pointer The particles sizes of the obtained nanostructures were about 20 nm and 40 nm. Black-Right-Pointing-Pointer The particles smaller than 5 nm were spherical/faceted and seems to be defect-free.

36 MATERIALS SCIENCE↗

DEVELOPMENT OF IN SITU TECHNIQUES FOR TORSION AND TENSION TESTING IN HYDROGEN ENVIRONMENT

Reliability of hydrogen storage tanks is significantly influenced by the mechanical performance of the container materials in the hydrogen environment. Fracture behavior and fracture toughness are of specific interest since they are relevant to many catastrophic failures. However, many conventional fracture testing techniques are difficult to be realized under the presence of hydrogen. Thus it is desired to develop novel in situ techniques to study the fracture behavior of structural materials in hydrogen environments. In this study, special testing apparatus were designed to facilitate in situ fracture testing in H2. In addition to a multi-notch tensile fixture, a torsional fixture was developed to utilize an emerging fracture testing technique, Spiral Notch Torsion Test (SNTT). The design concepts will be discussed. Preliminary in situ testing results indicated that the presence of H2 significantly reduces the fracture toughness of 4340 pipeline steels by up to 50 percent. On the other hand, SNTT tests conducted in air demonstrated a significant fracture toughness reduction in samples subject to Gleeble heat treatment, which illustrated the effect of welding on the fracture toughness of this material.

08 HYDROGEN↗

Reliable density functional calculations for the electronic structure of thermoelectric material ZnSb

In this paper, we present the results of systematic test calculations for the electronic structure of thermoelectric material ZnSb using a first-principles full-potential all electron computational method. We used a linear combination of atomic orbitals (LACO) formalism, based on density functional theory (DFT). The exchange-correlation interaction potential of the many electron system was described by using a generalized gradient approximation (GGA). We compared the calculated indirect and direct band gaps as well as the effective masses of holes and electrons in ZnSb with experimental measurement results. The calculated indirect band gap of ZnSb is 0.56 eV, which agrees very well with the experimentally measured values of 0.50 eV ~ 0.61 eV. The calculated direct band gap at X point is 0.89 eV. The calculated effective masses of electrons and holes in ZnSb also agree with experimental data. The systematical test calculations as well as the comparisons of the calculated results with experimental measurements show that the obtained electronic structure of ZnSb would be reliable. We did not observe a major deficiency of the first-principles DFT calculation for the electronic structure of ZnSb, using full-potential all electron LACO method. The reported electronic structure of single crystal ZnSb from this work may provide a fundamental knowledge base for further research and applications for this important thermoelectric material.

36 MATERIALS SCIENCE↗

An effective medium study of surface plasmon polaritons in nanostructured gratings using attenuated total reflection

Recent work studied surface plasmon resonances in structured materials by the method of attenuated total reflection using a prism on top of a metallic grating. That calculation considered Transverse Magnetic polarized radiation, involved an expansion in 121 Fourier modes, and found a number of interesting features. Many of these features were attributed to localized plasmons or other factors, which arise from a discrete structure. We use a simple effective medium theory to address the same problem, and find many of the same reflection features observed in the more complex calculation, indicating that localization is not an important factor. We also evaluate the possibility of using some of the new features in the reflection spectrum for bio-sensing and find that the sensitivity of the system to small changes in relative permittivity is increased compared to some standard methods.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The Mesoscale Science of the Matter-Radiation Interactions in Extremes (MaRIE) project

The National Nuclear Security Administration (NNSA) requires the ability to understand and test how material structures, defects, and interfaces determine performance in extreme environments such as in nuclear weapons. To do this, MaRIE will be an x-ray source that is laser-like and brilliant with very fl exible and fast pulses to see at weapons-relevant time scales, and with high enough energy to study critical materials. The Department of Energy (DOE) has determined there is a mission need for MaRIE to deliver this capability. MaRIE can use some of the existing infrastructure of the Los Alamos Neutron Science Center (LANSCE) and its accelerator capability. MaRIE will be built as a strategic partnership of DOE national laboratories and university collaborators.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Resonant Ultrasonic Spectroscopy: A Modal-Analysis Approach for Additive Manufacturing

Resonant ultrasonic spectroscopy is a methodology capable of measuring a change in modal resonant frequencies of material structures. It encompasses an inversion technique based on the eigen-frequencies of a simple regular sample geometry to estimate the elastic tensor of a solid. Obtaining an accurate and complete set of resonant frequencies is a critical first step in the RUS process. In this paper a variety of techniques to extract and validate material resonances from complicated RUS measurement spectra are developed. Various processing methodologies employing modal analysis techniques are applied to estimate the underlying resonances that lead to the extraction of the elastic coefficients characterizing the specimen under test. A case study of a simple isotropic material (304 SS) is investigated to analyze the algorithms and evaluate their performance

Coal, lignite, and peat↗

Ab Initio and Kinetic Rate Theory Modeling of 316SS with Oversized Solute Additions on Radiation-Induced Segregation

Deleterious effects of radiation in nuclear reactor systems cause material degradation and the potential for component failure. Radiation damage is fundamentally due to freely migrating point defects produced in collision cascades. A reduction in the freely migrating point defect population should, then, reduce radiation damage and increase component lifetime. The addition of oversized solute atoms such as Zr or Hf to 316SS, a common structural material in reactors, is expected to reduce point defect population through a trapping mechanism that enhances recombination. The mechanism, however, requires a strong binding energy between the oversized solute atom and vacancies in order for the mechanism to significantly reduce the defect population. Experimental measurements of this binding energy are unavailable, but can be determined with atomistic calculations. Ab initio methods are used here to determine binding energies and atomic volumes of either Hf or Zr oversized solutes with vacancies in a face-centered cubic Fe matrix. The binding energies are then used to parameterize a kinetic rate-theory model, which is used here to calculate radiation-induced segregation (RIS). The calculated values of RIS are then compared to experimental measurements to benchmark the calculations and offer insight into the proposed point defect trapping mechanism. (author)

36 MATERIALS SCIENCE↗

Measuring and Modulating Substrate Confinement during Nitrogen-Atom Transfer in a Ru 2 -Based Metal-Organic Framework

The porosity and synthetic tunability of metalorganic frameworks (MOFs) motivate interest in application of these materials as designer heterogeneous catalysts. While understanding substrate mobility in these materials is critical to the rational development of highly active catalyst platforms, experimental data are rarely available. Here we demonstrate kinetic isotope effect (KIE) analysis enables direct evaluation of the extent of substrate confinement as a function of material mesoporosity. Further, we provide evidence that suggests substrate confinement within a microporous Ru 2 -based MOF gives rise to quantum tunneling during interstitial C–H amination. Here, the reported data provide the first evidence for tunneling during interstitial MOF chemistry and illustrate an experimental strategy to evaluate the impact of material structure on substrate mobility in porous catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Verification of Modelica-Based Models with Analytical Solutions for Tritium Diffusion

Here, tritium transport in metal and molten salt fluids combined with diffusion through high-temperature structural materials is an important phenomenon in both magnetic confinement fusion (MCF) and molten salt reactor (MSR) applications. For MCF, tritium is desirable to capture for fusion fuel. For MSRs, uncaptured tritium potentially can be released to the environment. In either application, quantifying the time- and space-dependent tritium concentration in the working fluid(s) and structural components is necessary.Whereas capability exists specifically for calculating tritium transport in such systems (e.g., using TMAP for fusion reactors), it is desirable to unify the calculation of tritium transport with other system variables such as dynamic fluid and structure temperature combined with control systems such as those that might be found in a system code. Some capability for radioactive trace substance transport exists in thermal-hydraulic systems codes (e.g., RELAP5-3D); however, this capability is not coupled to species diffusion through solids. Combined calculations of tritium transport and thermal-hydraulic solution have been demonstrated with TRIDENT but only for a specific type of MSR.Researchers at Oak Ridge National Laboratory have developed a set of Modelica-based dynamic system modeling tools called TRANsient Simulation Framework Of Reconfigurable Models (TRANSFORM) that were used previously to model advanced fission reactors and associated systems. In this system, the augmented TRANSFORM library includes dynamically coupled fluid and solid trace substance transport and diffusion. Results from simulations are compared against analytical solutions for verification.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗