Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “reference frames”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Analysis of Launch Vehicle Liftoff Debris: Historical Perspective from Space Shuttle and Application to Artemis I

Human exploration-class launch vehicles are inherently prone to debris due to the extreme environments generated during pre-launch operations, liftoff, and flight. The use of cryogenic propellants often requires thermal protection system (TPS) coatings, typically foam, to maintain the propellant conditions in the tank and prevent an accumulation ice on the external surface of the vehicle. Some ice growth is to be expected at umbilical interfaces, vents, flanges, or brackets where it is difficult to apply TPS. This ice may come loose at any time due to wind on the launch pad, structural vibration and acoustics after rocket ignition, or aerodynamic forces during flight. This phenomena is especially apparent on vehicles with no TPS, such as the Saturn V rockets used in the Apollo Program, see Figure 1. During propellant tanking, the thermal contraction of the underlying substrate may generate cracks in the TPS (Figure 1). Chunks of TPS can release due to the expansion of ingested gas from cryopumping or from aerodynamic forces if the crack creates an offset surface. Most foams will also have a certain amount of “popcorning” where small pieces of foam will pop off during flight because of the differential between the static surface pressure and the pressure of the gas trapped in the foam cell structure. There are a number of other coating or closeout materials that may be shed from the vehicle and become debris. During pre-launch operations and liftoff, the vehicle may also be exposed to debris originating from the launch pad or ground support equipment. This debris is separate from foreign object debris, or FOD, which is not intended to be present and is strictly controlled through operations and maintenance procedures. In this case, debris is generated from hardware and materials that are necessary for launch and are subject to the intense vibration, acoustics, and direct plume impingement of the launch environment. Examples include ice from umbilicals, tape and tie wraps that protect cables, and rust or corrosion from the launch platform. While NASA has historically been aware of debris as a potential issue that could cause a failure resulting in loss of mission, loss of vehicle, or loss of crew, the likelihood and severity of that risk was not always well understood or given sufficient weight in program and flight decisions. After the Space Shuttle Columbia accident (STS-107), the investigation found that foam TPS debris shed from the external tank was the proximate cause of the damage to the orbiter wing. Six previous observations of debris released from the foam ramp that covered the bipod connecting the forward end of the orbiter to the external tank resulted in minor changes or were determined to be accepted flight risks. Two occurrences of bipod ramp foam loss were not identified until the STS-107 investigation. Despite the damage inflicted by these debris strikes, the Shuttle Program Requirements Control Board deemed the vehicle safe to fly. During the Return to Flight effort following the Columbia disaster, NASA Engineering developed a process for the assessment of debris transport, impact, and damage tolerance to support independent assessments of risk by NASA Safety and Mission Assurance (S&MA). Under this system, each element (vehicle or ground system) defines a catalog of all expected debris based on launch history, component testing, or analysis. Debris transport analysis (DTA) is conducted using the debris catalog characteristics and potential flow transport mechanisms (e.g., vehicle aerodynamics, gravity, wind, plume-driven). The predicted debris impact locations and velocities are provided to the hardware owners, who use available test data and analysis to determine whether each component can withstand the impacts. In cases where the element hardware may be severely damaged or fail, the options are to mitigate the debris source through some change in design or operation, or to work with S&MA to try to characterize the probability of the impact and damage for program risk acceptance. Because of the differences in debris characteristics and transport, the DTA has been divided between the Liftoff and Ascent regimes. The development and application of Liftoff DTA methodology from the Shuttle Program to the current Artemis Program is the subject of this paper. Liftoff DTA covers the time from the start of pre-launch operations at the launch pad, up until the vehicle clears the launch tower and there is no longer any interaction with ground systems. Debris transport during this period is broadly classified as either gravity, wind, and plume-entrained (GWPE) or plume driven (PD). GWPE debris is generally lower speed, travelling in a forward-to-aft direction. PD transport includes flow features from the rocket ignition transient, as well as plume impingement and recirculation that occur as the vehicle lifts off the launch platform. In these cases, the debris typically moves in an aft-to-forward direction at higher speeds. The applicable transport mechanisms must be considered for each piece of debris depending on the material, and release location and time. For example, rust or metallic debris from the tower could fall (GWPE) and impact the vehicle before landing on the launch platform deck where it could be also be transported by plume impingement (PD). However, falling ice (GWPE) from an umbilical is unlikely to survive impact with the vehicle or launch platform and be available for PD transport. Modeling of debris transport is accomplished using a set of DTA tools which simulate debris trajectories subject to a reference frame acceleration (i.e., gravity) and aerodynamic drag. Where the trajectory encounters a solid surface, the debris is allowed to rebound with a specified coefficient of restitution. The drag is calculated by interpolating the fluid state at each point in the debris trajectory from high-fidelity computational fluid dynamics (CFD) simulations of the launch vehicle and pad. The CFD data may either be static (steady state or time averaged), typically for GWPE transport, or dynamic (time-accurate) for PD flow features like the ignition transient. Examples of the CFD flow field solutions for the Space Launch System (SLS) rocket and launch pad are shown in Figure 2. Typical SLS debris trajectory predictions from DTA are illustrated in Figure 3. The final version of this paper will include a more detailed examination of the Liftoff DTA process developed during the Shuttle Program, and how it has been augmented and applied to the SLS rocket under the Artemis Program. Comparisons with debris observations from the Artemis I launch will demonstrate validation of the tools and methodology.

Debris↗

International DORIS Service (IDS): The IDS at 20 and the IVS at 25; Together on a Long Journey

This is an invited presentation to the the IVS General Meeting 2024 to celebrate the 25th anniversary of the International VLBI Service (IVS). The presentation shares aspects of the common journey of the International DORIS Service (IDS), and IVS over the last 20 years, as sibling services of the International Association of Geodesy, and as space geodetic techniques that contribute to the International Terrestrial Reference Frame (ITRF).

DORIS↗

Oblique Eccentric Gaze Holding Evokes Larger Horizontal than Vertical Rebound Nystagmus

Rebound nystagmus (RN) has been used to probe the adaptation mechanisms of the gaze holding system. This type of nystagmus is invoked upon returning to central gaze after prolonged fixation at an eccentric point and it is thought to reflect a set-point adaptation of the neural integrator circuit. Previous studies have only observed horizontal RN after horizontal eccentric gaze holding, reflecting adaptation of the horizontal neural integrator. The current study seeks to elucidate how eccentric gaze at oblique target locations, where there are equal horizontal and vertical components, affects the characteristics of the resulting RN. For a given trial, subjects were instructed to fixate a central flashing target for 5 seconds, then fixate an eccentric continuous target for 30 seconds at one of six possible locations (4 oblique and 2 horizontal targets), and finally fixate centrally at a flashing target for 15 seconds where RN is assessed. Binocular eye-tracking data were collected at 250 Hz. Slow-phase velocity (SPV) or the slow drift part of the nystagmus was used to quantify the magnitude of RN. Subjects showed elevated SPV in the horizontal component (2.3 deg/s), but less in the vertical component (1.4 deg/s) after oblique eccentric gaze holding, reflecting an oblique RN. The smaller vertical RN may reflect a different behavior of the horizontal and vertical neural integrators which are anatomically separated. Under the current paradigm, oblique gaze holding would appear to have a smaller effect on adaptation of the vertical integrator than in the horizontal integrator. Further investigation is needed to establish the reference frame of this distinction between the horizontal and vertical integrator circuits.

gaze holding↗

New Capabilities and Improvements to the High-Order Glenn Flux Reconstruction Code

The Glenn Flux Reconstruction (GFR) code is a computational fluid dynamics (CFD) code under development at NASA Glenn Research Center. GFR is based on the high-order flux reconstruction (FR) method and provides a large-eddy simulation (LES) capability that is both accurate and efficient for complex aeropropulsion flows. Three significant new capabilities have been added to the code that improve its performance and functionality. First, a variety of explicit Runge-Kutta methods, including some with adaptive time stepping, were added to GFR with two methods offering a 33% improvement in time-to-solution. Second, GFR can now utilize fully unstructured, mixed-element meshes to more easily facilitate the grid generation process for complex geometries. Finally, a rotating reference frame capability has been added to GFR for solving rotating turbomachinery problems. A selection of results demonstrating these new capabilities are presented in this work. The Taylor-Green vortex problem is used to verify the new unstructured capability by showing similar accuracy and resolution for all element types. LES of the Turbulent Heat Flux Phase III (THX3) experiment with comparison to another high-order LES code and a popular Reynolds-averaged Navier-Stokes (RANS) code demonstrates the accuracy of the code for complex aeropropulsion flows. Finally, LES of a spacecraft cabin ventilation fan shows the ability of GFR to efficiently establish a fan performance map and identify operating points for further analysis at high orders of accuracy.

High-Order Methods↗

Investigating Low-Altitude Constellations of Ad-Hoc Lunar PNT System for Distributed Spacecraft Autonomy

In this study, we examine a low-altitude Lunar Position, Navigation, and Timing (LPNT) constellations and the localization performance of Centralized Extended Kalman Filter (CEKF) and Decentralized Extended Kalman Filter (DEKF) algorithms. The primary investigation involves a 100-node swarm operating at a 100 km altitude, in contrast to previous studies that examined a 21-node asset in a frozen-orbit at 5,500 km. The autonomous operation of large-scale swarm is based on two-way Inter-Satellite Link (ISL) measurements, which involve pseudoranges and relative velocities among swarm nodes. We perform a numerical assessment of the two filtering approaches, utilizing ‘fully sampled’ measurements from all available assets as well as ‘two ISL’ measurements where each spacecraft is restricted to only two antennas. This research includes an analysis of CEKF under 2-ISL constraints and evaluates the performance of DEKF in a 100-node swarm, which has not been explored in previous studies. In addition, we examine the impact of increasing the sampling frequency for DEKF, showing that the update cycle can be shortened from a 10-minute interval. A novel approach for ‘2-ISL limited’ DEKF will also be introduced, using a matching formulation that exhaustively enumerates all potential matches. This study provides valuable insights into large-scale distributed swarm operations, considering various filter configurations, sampling frequencies, matching strategies, and scalability of CEKF and DEKF for low-altitude LPNT applications. The Lunar PNT technology plays a key role in providing reliable and robust navigation services on the Moon's surface and the South pole, where the primary Lunar missions are planned. To support upcoming Lunar missions, including small satellites from NASA's Commercial Lunar Payload Services program, the Lunar PNT system must be adaptable to smaller platforms like CubeSats. Driven by the growing involvement of public and private exploration partnerships, the traditional low Earth orbit missions are shifting to beyond geosynchronous orbit [1]. These upcoming missions aim to foster a sustainable and innovative exploration program, in collaboration with commercial and international partners, to facilitate human expansion throughout the solar system and return new knowledge and opportunities to Earth [2]. As part of this trend, there are increasing efforts to utilize science missions in Lunar orbit to develop a non-dedicated and ad-hoc PNT network system. Two traditional approaches, the Deep Space Network (DSN) and the weak signal Global Positioning System (GPS), are established deep-space navigation technologies for missions beyond the geosynchronous orbit. Beginning in 1958, the DSN was developed to communicate with the Explorer 1 spacecraft based on the use of radiometric tracking in spacecraft navigation [3]. The DSN is capable of providing nearly unfettered coverage to spacecraft beyond low-Earth orbit (LEO), however, increased space mission volume has created concerns about future expectations of DSN usage for spacecraft navigation [4]. For cislunar mission applications, the position accuracy using DSN achieves 100 m (3σ) with at least three geometrically diverse ground stations when using radiometric tracking alone [5]. The DSN's dependence on Earth-based ground stations restricts its operational capabilities to periods of Earth visibility. This limitation, coupled with its poor localization performance, renders the DSN unsuitable for future lunar missions that demand continuous tracking and precise positioning. To satisfy the increasing requirements of DSN in Lunar applications, spacecrafts are also required to improve their onboard antenna power and efficiency of the transmission. However, there is an important aggregate cost trade between adding capabilities to every spacecraft and adding to a capacity on the ground that serves multiple spacecraft [6]. A weak GPS system can provide PNT service while the user spacecraft is bound to the Moon, leveraging a single, steerable high gain antenna with the relatively narrow beam which includes all the sources in its field of view [7]. However, the higher the altitude the receiver is above the GPS constellations, the poorer and the weaker are the relative geometry and the received signal powers, respectively, leading to a significant navigation accuracy reduction [8]. The transmitted power becomes weaker with increasing distance from the Earth as well as signals tracked from one of the side lobes of the GPS antenna pattern. As a results, the number of visible satellites and relative geometric condition of the GPS satellites at very high altitude drops dramatically and reduces the navigation solution accuracy. Therefore, the weak GPS system is also not an ideal way to provide PNT service to upcoming Lunar missions when considering its limited geometric condition and the recued navigation accuracy. Another navigation approach on the Moon is being developed, similar to the Global Navigation Satellite System (GNSS) on Earth, aiming to offer navigation service with continuous 24/7 coverage across the entire Lunar surface. For example, lunar communications relay and navigation systems (LCRNS) by NASA and Lunar navigation satellite systems (LNSS) by JAXA are designed to serve as dedicated Position, Navigation, and Timing (PNT) systems for the Moon. However, designing a dedicated LNSS and PNT service involves additional challenges, which are unique to the lunar environment, including limited payload capacity for the CubeSat platform, i.e., the size, weight, and power (SWaP) of the onboard clock, limited lunar ground monitoring stations, and limited financial investment as compared to the legacy Earth-GPS [9]. NASA’s focus on utilizing CubeSat platforms on the Moon leads to an alternative Lunar navigation platform that leverages the existing Lunar science and exploration assets. The small satellites used in Lunar missions can be used to create a low-cost, autonomous, ad-hoc, and on-demand mission-centric Lunar PNT swarm capable of providing PNT services to these low-cost lunar missions [10]. As upcoming Lunar missions will often operate at low-altitude about 30 km to 100 km for scientific observations and mapping purposes, the low-altitude orbital constellations could be employed to create an ad-hoc Lunar PNT system. However, several issues must be addressed, such as the instability of these orbits, which often require maintenance or are only suitable for short-duration missions, operating for fewer than 90 days. Additionally, at an altitude of 100 km, the satellites have a limited period during which they are above the horizon and capable of providing PNT service to users. The implementation of a non-dedicated, ad-hoc Lunar navigation constellation facilitates on-demand PNT services. A preliminary study of ad-hoc Lunar PNT system was conducted using 21 spacecraft in 5,5000 km altitude frozen orbits to test its feasibility and a basic performance of orbital asset localization among ad-hoc Lunar constellations in small satellites format [10]. These swarm assets are designed for autonomous localization with minimal Earth interaction, reducing dependency on bandwidth and ground resources. The design in [10] demonstrated the feasibility of a decentralized PNT approach, specifically employing a DEKF approach for state estimation, which helps minimize onboard operating costs. The DEKF method distributes computation across individual satellites, which lightens the computational load while maintaining accuracy in orbit ephemeris and clock offsets, similar to centralized systems [11]. In a follow-on study [12], each spacecraft was limited to 2 communications antennae, forcing the selection of measurements and scheduling spacecraft activities to perform the measurements. A matching algorithm is implemented to select the best measurements and schedule position estimation updates. The decentralized localization performance is also investigated with increasing levels of network degradation for swarm assets considering the impact of intermittent and permanent communication failure, to demonstrate the robustness and fidelity of the decentralized Lunar PNT service [13]. This study confirmed that the ad-hoc PNT constellations in frozen orbit are highly robust and resilient to communication failures. However, unlike frozen orbit swarm assets, the low-altitude satellites have a limited ground view at an altitude of 100 km, where the ad-hoc Lunar constellation consists of 98 low-altitude satellites, evenly distributed across seven circular polar orbital planes, alongside two satellites in a frozen orbit at an altitude of 5,500 km (Figure 1). Therefore, the number of satellites visible to ground users is significantly limited in low-altitude orbit constellations. As each visibility of a spacecraft remains intact for only a few ticks before it moves out of the field of view, the ground user encounters challenges in maintaining continuous navigation service, resulting in sparse availability and provision of Lunar PNT system. Consequently, service availability is primarily restricted to the Lunar South Pole region (Figure 2). Given these limitations and concerns, the localization performance of low-altitude swarm assets will be assessed in this study. We focus on the investigation of the localization performance of low-altitude swarm assets and ground users near the Lunar South Pole. The overall flow of the Lunar PNT simulation incorporates the DEKF approach of asset localization and the weighted least-squares approach in user localization (Figure 3). The autonomous Lunar PNT simulation is primarily implemented in MATLAB, where the DEKF based on the matching scheduler is implemented with Google’s OR-tools as a model builder and Gurobi optimization tool as a backend solver. The General Mission Analysis Tool (GMAT) is utilized to generate ephemeris data for swarm assets, and accounts for satellite orbital details, mass, and perturbations like solar radiation pressure and drag coefficients. Each ephemeris dataset is produced in the Moon International Celestial Reference Frame (ICRF) inertial coordinate system. For state estimation, the distributed swarm assets rely on two-way Inter-Satellite Link (ISL) measurements, which involve tracking pseudoranges and relative velocities between visible satellites and anchor nodes during each observation. Numerical evaluations of the decentralized localization process are conducted to demonstrate the feasibility of the low-altitude PNT system in providing reliable navigation services. The main approach involves using DEKF and CEKF to localize 100 satellites in low-altitude constellations, where the CEKF is implemented to serve as a baseline for comparing the performance of distributed algorithms. In both cases, we evaluate ‘fully sampled’ measurements from all available assets, and ‘two ISL’ measurements when spacecraft are constrained to have only two antennas. We test four estimation techniques: CEKF fully sampled, CEKF two ISL, DEKF fully sampled, and DEKF two ISL filters. As the DEKF update cycle is comprised of network setup, communication, and computations, a global broadcast network and 2-way ISL network setup will take from 4 to 6 minutes as maximum [12]. In this simulation, the DEKF update cycle is set to 10 minutes, including a 4-minute latency for obtaining and computing the actual measurement updates. We experiment an increased update cycle to demonstrate the feasibility and evaluate the impact on localization performance using various tuning values for measurement noise covariances (Figures 4 and 5). By comparing centralized and decentralized approaches using a matching algorithm, we analyze the influence of cross-correlation factors in the covariance matrix, assuming 100% reliability of all assets and measurements. The increased frequency and the adjustments of tuning parameters reveal distinct error patterns between the two scenarios. The localization accuracy of the swarm assets and ground users is assessed by taking the median error across 100 assets and one ground user (84.9°S, 137.5°E) over 7-day simulation period (Table 1). Since the user localization accuracy is significantly affected by the performance of the swarm assets, it is crucial to maintain high localization accuracy within the swarm. This study will continue to explore decentralized filtering for autonomous LPNT operations, with further investigation of an 'iterative' matching approach which enumerates every valid matching pair, planned for the following month.

Yeji Kim↗

Lunar Laser Ranging in the Artemis Era

The retroreflector arrays placed on the lunar surface by the Apollo astronauts and the Soviet Luna missions continue to contribute to our understanding of gravitational physics, Earth and Moon geophysics, geodesy, and dynamics. The key science questions addressed by Lunar Laser Ranging remain very relevant today: What is the interior structure of the Moon? Is the Equivalence Principle exact? Does the strength of gravity vary with space and time? What is the nature of spacetime? Do extra dimensions or other new physics alter the inverse square law of gravity? The lunar retroreflectors are also an essential component of the realizations of the lunar reference frames. The half-century old lunar retroreflectors continue to provide excellent ranging targets but are showing signs of degradation and the measurement error associated with their physical size and varying tilt is becoming a limitation in the quest for more precise range measurements. In addition, the clustering of the arrays in the mid-latitudes of the Moon limits their geometrical strength and coverage. The south polar region planned for Artemis presents an ideal opportunity for improving the geometric distribution. Retroreflectors utilizing a large optical cross-section single cube corner do not have tilt error associated with the existing arrays making them good options for lunar deployment. Several new retroreflectors of this type are being prepared for upcoming Commercial Lunar Payload Services missions as well as Artemis. This presentation will discuss NASA’s plans for expanding the lunar laser ranging capabilities with a focus on the Artemis Lunar Laser Retroreflector.

Stephen Merkowitz↗

New Capabilities and Improvements to the High-Order Glenn Flux Reconstruction Code

The Glenn Flux Reconstruction (GFR) code is a computational fluid dynamics (CFD) code under development at NASA Glenn Research Center. GFR is based on the high-order flux reconstruction (FR) method and provides a large-eddy simulation (LES) capability that is both accurate and efficient for complex aeropropulsion flows. Three significant new capabilities have been added to the code that improve its performance and functionality. First, a variety of explicit Runge-Kutta methods, including some with adaptive time stepping, were added to GFR with two methods offering a 33% improvement in time-to-solution. Second, GFR can now utilize fully unstructured, mixed-element meshes to more easily facilitate the grid generation process for complex geometries. Finally, a rotating reference frame capability has been added to GFR for solving rotating turbomachinery problems. A selection of results demonstrating these new capabilities are presented in this work. The Taylor-Green vortex problem is used to verify the new unstructured capability by showing similar accuracy and resolution for all element types. LES of the Turbulent Heat Flux Phase III (THX3) experiment with comparison to another high-order LES code and a popular Reynolds-averaged Navier-Stokes (RANS) code demonstrates the accuracy of the code for complex aeropropulsion flows. Finally, LES of a spacecraft cabin ventilation fan shows the ability of GFR to efficiently establish a fan performance map and identify operating points for further analysis at high orders of accuracy.

Direct Numerical Simulations↗

Relation Between Magnetopause Position and Reconnection Rate Under Quasi‑Steady Solar Wind Dynamic Pressure

The lunar environment heliospheric X-ray imager (LEXI) and solar wind–magnetosphere–ionosphere link explorer (SMILE) will observe the magnetopause motion in soft X-rays to understand dayside reconnection modes as a function of solar wind conditions after their respective launches in the near future. To support their successful science mission, we investigate the relationship between the magnetopause position and the dayside reconnection rate by utilizing super dual auroral radar network (SuperDARN) observations and widely used empirical models of magnetopause position (Shue et al. in J Geophys Res 103:17691–17700. https://doi.org/10.1029/98JA01103, 1998 and Lin et al. in J Geophys Res 115:A04207. https://doi.org/10.1029/2009JA014235, 2010). We select three cases when the interplanetary magnetic field rotates during periods of quasi-steady solar wind dynamic pressure. We first estimate the dayside reconnection rate by calculating the electric field along the open–closed magnetic field boundary (OCB) in the OCB moving reference frame. Then, we estimate the magnetopause position near the local noon by inputting NASA OMNI solar wind data into the empirical magnetopause models. The reconnection rate shows anti-correlation with the magnetopause position that it generally increases as the magnetopause located closer to Earth and vice versa. Our result also confirms that the reconnection rate increases as the empirical coupling efficiency between solar wind and the magnetosphere increases.

Hyangpyo Kim↗

Camera Calibration and Alignment Metrology at Johnson Space Center’s Electro-Optics Laboratory

It is increasingly common to see spacecraft equipped with cameras for the purpose of navigation. Images are either sent to Earth or processed autonomously on-board to provide information about the vehicle’s position, velocity, and/or attitude. These can be images of stars or celestial bodies for absolute navigation, or images of another spacecraft for relative navigation. While monocular cameras do not provide range information, the images they capture can be processed to determine bearing vectors to target objects within the camera’s field of view. For a camera to be effective in navigation, it must be carefully calibrated and aligned. This involves accurately modeling the optical effects that govern the projection of line-of-sight directions onto the camera’s pixels and determining the camera’s orientation relative to the spacecraft’s reference frame. Engineers at Johnson Space Center’s Electro-Optics Lab regularly perform camera inspection, calibration, and alignment metrology. This was done for the Orion Optical Navigation (OpNav) Camera, the Orion Docking Camera (DCAM), and for numerous cameras belonging to commercial partners. The nature of optical navigation means that cameras must be well-calibrated and their attitude well understood to provide high accuracy bearing measurements to the navigation filter. The stringent accuracy requirements for Orion could not have been met using traditional checkerboard camera calibration or by simply relying on design drawings. This paper details the hardware, software, techniques, and algorithms used by the EOL team to achieve this level of accuracy.

Paul D Mckee↗

Camera Calibration and Alignment Metrology at Johnson Space Center’s Electro-Optics Laboratory

It is increasingly common to see spacecraft equipped with cameras for the purpose of navigation. Images are either sent to Earth or processed autonomously on-board to provide information about the vehicle’s position, velocity, and/or attitude. These can be images of stars or celestial bodies for absolute navigation, or images of another spacecraft for relative navigation. While monocular cameras do not provide range information, the images they capture can be processed to determine bearing vectors to target objects within the camera’s field of view. For a camera to be effective in navigation, it must be carefully calibrated and aligned. This involves accurately modeling the optical effects that govern the projection of line-of-sight directions onto the camera’s pixels and determining the camera’s orientation relative to the spacecraft’s reference frame. Engineers at Johnson Space Center’s Electro-Optics Lab regularly perform camera inspection, calibration, and alignment metrology. This was done for the Orion Optical Navigation (OpNav) Camera, the Orion Docking Camera (DCAM), and for numerous cameras belonging to commercial partners. The nature of optical navigation means that cameras must be well-calibrated and their attitude well understood to provide high accuracy bearing measurements to the navigation filter. The stringent accuracy requirements for Orion could not have been met using traditional checkerboard camera calibration or by simply relying on design drawings. This paper details the hardware, software, techniques, and algorithms used by the EOL team to achieve this level of accuracy.

Paul McKee↗

Evolving the SpaceFOM: Lessons Learned and Future Development

For over fifty years, simulation has been a cornerstone technology for space missions. In many cases, one single simulator, developed by one team, is not enough to meet the simulation objectives. Astronaut crew training, docking, vehicle testing and complex mission planning all require several simulations to be connected and to interoperate, in order to achieve the goal of the simulation. To facilitate the development of interoperable simulations, an open standard, the SISO SpaceFOM was developed in collaboration between government, industry and academia. The standard was released in 2020. The initial release of SpaceFOM focuses on the core interoperability topics for space simulation: (i) specifying spatial data using several, well defined reference frames, (ii) managing time (including real-time, hard real-time, and as-fast-as-possible execution), (iii) composition of systems with subsystems such as space vehicles, and (iv) execution control, such as initializing, running, pausing, and terminating simulations. A number of requirements for the next version of SpaceFOM have been identified and proposed solutions are already under development. One key area is the object classes used for data exchange, where a richer set of classes have been proposed, based on practical use cases. For time management, the use of variable time resolutions and variable time steps is also proposed. For execution control, save and restore of simulations is considered as well as improved robustness, to handle failing components. A number of clarifications are also under consideration. This paper provides both a forward-looking view of the technical developments underway and a retrospective on the standard's evolution. The authors emphasize that prioritizing core challenges and delivering a practical first version were crucial steps. While not every idea was implemented in the initial release, the timely delivery of a functional standard enabled real-world applications, the growth of a user community, and the collection of valuable insights to shape future versions. The authors look forward to working with the next version of SpaceFOM together with the growing user community.

FOMs↗

Ontology Language to Support Description of Experiment Control System Semantics, Collaborative Knowledge-Base Design and Ontology Reuse

In this paper we discuss the control domain specific ontology that is built on top of the domain-neutral Resource Definition Framework (RDF). Specifically, we will discuss the relevant set of ontology concepts along with the relationships among them in order to describe experiment control components and generic event-based state machines. Control Oriented Ontology Language (COOL) is a meta-data modeling language that provides generic means for representation of physics experiment control processes and components, and their relationships, rules and axioms. It provides a semantic reference frame that is useful for automating the communication of information for configuration, deployment and operation. COOL has been successfully used to develop a complete and dynamic knowledge-base for experiment control systems, developed using the AFECS framework.

43 PARTICLE ACCELERATORS↗

Monte Carlo based investigation of Berry phase for depth resolved characterization of biomedical scattering samples

The propagation of light in turbid media is an active area of research with relevance to numerous investigational fields, e.g., biomedical diagnostics and therapeutics. The statistical random-walk nature of photon propagation through turbid media is ideal for computational based modeling and simulation. Ready access to super computing resources provide a means for attaining brute force solutions to stochastic light-matter interactions entailing scattering by facilitating timely propagation of sufficient (>10million) photons while tracking characteristic parameters based on the incorporated physics of the problem. One such model that works well for isotropic but fails for anisotropic scatter, which is the case for many biomedical sample scattering problems, is the diffusion approximation. In this report, we address this by utilizing Berry phase (BP) evolution as a means for capturing anisotropic scattering characteristics of samples in the preceding depth where the diffusion approximation fails. We extend the polarization sensitive Monte Carlo method of Ramella-Roman, et al.,1 to include the computationally intensive tracking of photon trajectory in addition to polarization state at every scattering event. To speed-up the computations, which entail the appropriate rotations of reference frames, the code was parallelized using OpenMP. The results presented reveal that BP is strongly correlated to the photon penetration depth, thus potentiating the possibility of polarimetric depth resolved characterization of highly scattering samples, e.g., biological tissues.

back scattered Mueller matrix↗

SOFAST: Sandia Optical Fringe Analysis Slope Tool

SOFAST is used to characterize the surface slope of reflective mirrors for solar applications. SOFAST uses a large monitor or projections screen to display fringe patterns, and a machine vision camera to image the reflection of these patterns in the subject mirror. From these images, a detailed map of surface normals can be generated and compared to design or fitted mirror shapes. SOFAST uses standard Fringe Reflection (Deflectometry) approaches to measure the mirror surface normals. SOFAST uses an extrinsic analysis of key points on the facet to locate the camera and monitor relative to the facet coordinate system. It then refines this position based on the measured surface slope and integrated shape of the mirror facet. The facet is placed into a reference frame such that key points on the facet match the design facet in orientation and position. This is key to evaluating a facet as suitable for a specific solar application. SOFAST reports the measurements of the facet as detailed surface normal location in a format suitable for ray tracing optical analysis codes. SOFAST also reports summary information as to the facet fitted shape (monomial) and error parameters. Useful plots of the error distribution are also presented.

Andraka, Charles E.↗

Coupled Fluid-Solid Interaction Under Shock Wave Loading: Part I - Statistic Interfaces

Here, this paper is the first of two that consider the treatment of fluid-solid interaction problems under shock wave loading, where the solid experiences large bulk Lagrangian displacements. This work addresses the issues associated with using a level-set as a generalized interface for fluid-solid coupling where unstructured overlapping grids are used for the fluid and solid domains. In part-I of this work, we outline the formulation used for the edge-based unstructured-grid Euler solver in the context of the discontinuous-Galerkin method. The identification of the fluid-solid interface on the unstructured fluid mesh uses a super-sampled L 2 projection technique, that in conjunction with a Lagrangian interface position, permits fast identification of the interface and the concomitant imposition of boundary conditions. The use of a narrow-band approach for the identification of the wetted interface is presented with the details of the construction of interface conditions. A series of computations are presented to demonstrate the validity of the current approach on problems with static interfaces. In part-II, we present the coupled dynamic fluid-solid system, and present an explicit monolithic algorithm for the treatment of the fully-coupled system. The interface conditions associated with moving interfaces is considered, and a comparison of moving vs. static reference frames is used to evaluate the dynamic interface treatment. Finally, a series of two and and three-dimensional projectile and shock-body calculations are presented.

42 ENGINEERING↗

Coupled Fluid-Solid Interaction Under Shock Wave Loading: Part II - Dynamic Interfaces

This article is the second of two that consider the treatment of fluid-solid interaction problems where the solid experiences wave loading and large bulk Lagrangian displacements. In part-I, we presented the formulation for the edge-based unstructured-grid Euler solver in the context of a discontinuous- Galerkin framework with the extensions used to treat internal fluid-solid interfaces. A super-sampled L 2 projection was used to construct level-set data from the Lagrangian interface, and a narrow-band approach was used to identify and construct appropriate ghost data and boundary conditions at the fluid-solid interface. A series of benchmark problems were used to verify the treatment of the fluid-solid interface conditions with a static interface position. In this paper, we consider the treatment of dynamic interfaces and the associated large bulk Lagrangian displacements of the solid.We present the coupled dynamic fluid-solid system, and develop an explicit, monolithic treatment of the fully-coupled system. The conditions associated with moving interfaces and their implementation are discussed. A comparison of moving vs. fixed reference frames is used to verify the dynamic interface treatment. Lastly, a series of two and and three-dimensional projectile and shock-body interaction calculations are presented. Ultimately, the use of the Lagrangian interface position and a super-sampled projection for fast level-set construction, the narrow-band extraction of ghost data, and monolithic explicit solution algorithm has proved to be a computationally efficient means for treating shock induced fluid-solid interaction problems.

42 ENGINEERING↗

Application specific emission and transmission tomography

A compact and mobile gantry for 3-dimensional Application Specific Emission and/or Transmission Tomography (ASETT) imaging of the breast in single photon or coincidence emission modes, and single photon, or coincidence, or x-ray transmission modes. While the ASETT gantry was designed, built and evaluated for imaging metabolically active lesions in the pendant breast, it can also be used to image other organs and objects. This system overcomes physical constraints associated with imaging a pendulous breast in prone patients, while simultaneously satisfying sampling criteria for sufficient data collection in the pendulous breast reference frame. When combined with an offset cone-beam tomographic x-ray transmission imaging system, this dual modality ASETT system could provide simultaneous and coregistered structural and functional information about large or dense breasts, breasts with indeterminate x-ray mammography, and could also be used to accurately 3-dimensionally guide biopsy or surgical resection. Moreover, with the offset beam orientation, the transmission system is designed to have a variable FOV and minimize overall absorbed breast dose.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Impedance Characterization of Utility-Scale Renewable Energy and Storage Systems: Preprint

This paper presents the impedance characterization of utility-scale wind turbines and PV/storage inverters using a multimegawatt grid simulator-based grid integration testbed. The paper describes testbed components including a 7 MVA grid simulator, 5 MW dynamometer, medium-voltage measurement system, and real-time control system used for automated impedance characterization of wind turbines and inverters. Different aspects of impedance measurement are discussed, including the selection of the magnitude and type of perturbation, measurement of frequency cross-coupling between sequence impedance responses, and the alignment of the reference frame for sequence impedance measurement. The paper also demonstrates high-fidelity validation of EMT simulation models and characterization of grid-forming inverters using impedance measurements.

17 WIND ENERGY↗