Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “polarization selection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Injection module thrust vector control

A three-axis controlled Injection Module propelled by a Star 48 solid rocket motor has been considered for use as a final 'kick' stage to supplement the Inertial Upper Stage in a proposed launch option for the Galileo and International Solar Polar missions. A flight control law for the Injection Module is developed. A position plus rate control law is considered, with integral, path guidance, and derived rate terms added for improved pointing accuracy and fuel efficiency. Selection of control gains is accomplished with the help of analytical limit cycle expressions and verified by computer simulation of the closed loop system. A computer simulation of the flight control system is built around a rigid spacecraft model with gyro dynamics and thruster delays included. Models for pitch/yaw/roll disturbance torques are included. Through simple gain changes the proposed flight control law is shown to accommodate the widely different mass properties of the Galileo and International Solar Polar spacecraft. Pointing accuracies of better than the desired 0.2 degrees are achieved.

Bell, C. E.↗

Quantum interferometry and pathway selectivity in the nonlinear response of photosynthetic excitons

We propose a time–frequency resolved spectroscopic technique which employs nonlinear interferometers to study exciton–exciton scattering in molecular aggregates. A higher degree of control over the contributing Liouville pathways is obtained as compared to classical light. We show how the nonlinear response can be isolated from the orders-of-magnitude stronger linear background by either phase matching or polarization filtering. Both arise due to averaging the signal over a large number of noninteracting, randomly oriented molecules. We apply our technique to the Frenkel exciton model which excludes charge separation for the photosystem II reaction center. We show how the sum of the entangled photon frequencies can be used to select two-exciton resonances, while their delay times reveal the single-exciton levels involved in the optical process.

Science & Technology - Other Topics↗

Factors Determining Selectivity of Acid- and Base-Catalyzed Self- and Cross-Condensation of Acetone and Cyclopentanone

In a combined kinetics and density functional theory (DFT) study, we have explored several factors that affect the selectivity of acid- and base-catalyzed self- and cross-aldol condensation of acetone (ACE) and cyclopentanone (CPO). These factors include competitive adsorption, molecular structure, and electron polarization of the two ketones on the catalyst surface. Here, kinetic analysis shows that on MgO, self-condensation of both ACE and CPO is limited by the initial unimolecular enolization step. Accordingly, CPO exhibits a higher self-condensation rate than ACE due to the more favorable α-C–H abstraction by the basic O site. The thermodynamic parameters derived from the kinetic analysis indicate that under cross-condensation reaction conditions, the MgO surface fraction covered by CPO is significantly higher than that covered by ACE. Therefore, the product distribution is dominated by [CPO]-activated products ([CPO]CPO + [CPO]ACE). Also, for a given enolate (indicated as [CPO] or [ACE]), the higher surface coverage of CPO leads to enhanced C–C coupling with CPO as the electrophile ([CPO]CPO > [CPO]ACE; [ACE]CPO > [ACE]ACE). By contrast, for both acid catalysts investigated, the rate-limiting step is the bimolecular C–C coupling, with aspects of this step depending on the density of acid sites. That is, on the high-acid-density MCM-41-SO 3 H catalyst, condensation follows a bimolecular dual-site mechanism (Langmuir–Hinshelwood model). On this catalyst surface, the ACE coverage is higher than that of CPO, which causes a higher selectivity for those products in which ACE is the electrophile ([CPO]ACE > [CPO]CPO; [ACE]ACE > [ACE]CPO). Steric hindrance is another factor that affects selectivity in the same way, favoring products in which the electrophile is ACE since it presents a lower steric hindrance to C–C coupling than CPO. Therefore, the same sequence of products is obtained for the low-acid-density MCM-41-SO 3 H catalyst, which proceeds on a single-acid site with the other molecule in the liquid phase (Eley–Rideal model). In this case, the electrophile coverage is not relevant, but the steric hindrance is, yielding the same trend as above ([CPO]ACE > [CPO]CPO; [ACE]ACE > [ACE]CPO).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Simulation of electromechanical responses of ferroelectric ceramics driven by alternating compressive stress and static electric field

The effect of static electric field on mechanical and dielectric properties of a lead zirconate titanate (PbZr{sub x}Ti{sub 1-x}O{sub 3}) piezoceramic sample driven by an alternating compressive stress has been experimentally investigated by Zhou et al.[J. Am. Ceram. Soc. 88, 867 (2005)]. Numerical simulation for this experimental result using two-dimensional four-state Potts model is presented in this article. Upon polarization switching, the dipole in the perovskite cell undergoes 90 deg. rotation, which is in turn associated with the switching of ferroelastic strain state. Consequently, the stress-strain relation and hence the mechanical stiffness are strongly influenced by the magnitude of the dc bias. Optimal mechanical and piezoelectric responses can be obtained by the suitable selection of biasing field.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Corrosion evaluation of alloys and MCrAlX coatings in molten carbonates for thermal solar applications

Here, stainless steels (SS) 310, 321, 347, Incoloy 800H (In800H), alumina-forming austenitic (AFA-OC6), Ni superalloy Inconel 625 (IN625), and MCrAlX (M: Ni, and/or Co; X: Y, Hf, Si, and/or Ta) coatings were corroded in molten carbonates in N 2 and bone-dry CO 2 atmospheres. Electrochemical tests in molten eutectics K 2 CO 3 -Na 2 CO 3 and Na 2 CO 3 -K 2 CO 3 -Li 2 CO 3 at temperatures higher than 600 °C were evaluated using an open-circuit potential followed by a potentiodynamic polarization sweep to determine the corrosion rates. Because the best-performing alloys at 750 °C were In800H followed by SS310, these two alloys were selected as the substrate material for the MCrAlX coatings. The coatings were able to mitigate corrosion in molten carbonates environments. The corrosion of substrates SS310 and In800H was reduced from ~2500 um/year to 34 um/year when coated with high-velocity oxyfuel (HVOF) NiCoCrAlHfSiY and pre-oxidized (air, 900 °C, 24 h, 0.5 °C/min) before molten carbonate exposure at 700 °C in bone-dry CO 2 atmosphere. Metallographic characterization of the corroded surfaces showed that the formation of a uniform alumina scale during the pre-oxidation seems to protect the alloy from the molten carbonate attack.

14 SOLAR ENERGY↗

Chemical Design of Pb-Free Relaxors for Giant Capacitive Energy Storage

Dielectric capacitors have captured substantial attention for advanced electrical and electronic systems. Developing dielectrics with high energy density and high storage efficiency is challenging owing to the high compositional diversity and the lack of general guidelines. Herein, we propose a map that captures the structural distortion ($\delta$) and tolerance factor (t) of perovskites to design Pb-free relaxors with extremely high capacitive energy storage. Our map shows how to select ferroelectric with large $\delta$ and paraelectric components to form relaxors with a t value close to 1 and thus obtaining eliminated hysteresis and large polarization under a high electric breakdown. Taking the Bi 0.5 Na 0.5 TiO 3 -based solid solution as an example, we demonstrate that composition-driven predominant order-disorder characteristic of local atomic polar displacements endows the relaxor with a slushlike structure and strong local polar fluctuations at several nanoscale. This leads to a giant recoverable energy density of 13.6 J cm -3 , along with an ultrahigh efficiency of 94%, which is far beyond the current performance boundary reported in Pb-free bulk ceramics. In conclusion, our work provides a solution through rational chemical design for obtaining Pb-free relaxors with outstanding energy-storage properties.

25 ENERGY STORAGE↗

Using chiral-induced spin selectivity as a tool to improve materials and processes for energy science

Studies relating to electrical energy conversion, storage, and generation, date back to the 19th century, however only in recent years have scientists begun to investigate the impact of the electron spin on these processes. Control and manipulation of the electron spin, an intrinsically quantum property of matter, opens new approaches to addressing energy science challenges. Furthermore, the chiral-induced spin selectivity (CISS) effect is enabling for this effort, because of the control over the transport and generation of both pure spin currents and spin-polarized charge currents. In this review article, we begin with a brief introduction on design strategies for the implementation of CISS in materials and then describe recent studies that demonstrate how CISS can be used to improve electrocatalysis and spintronics. Lastly, we conclude with forward-looking thoughts on the next steps for leveraging CISS in energy science.

Batteries↗

Capture Cavities For The Cw Polarized Positron Source Ce + baf

The initial design of the capture cavities for the continuous wave (CW) polarized positron beams at Jefferson Lab (Ce + BAF) is presented. A chain of standing wave multi-cell copper cavities inside a solenoid tunnel are selected to improve the positron capture efficiency. The cavity design strategy is presented to accommodate constrains from the large phase distribution of the incident beams, RF power and RF heating. A matrix of design parameters’ range are given for future system optimization when the capture cavities are considered together with other sub-systems and beam dynamics. The contents will also be useful for other CW cavity design for beams with large phase space distribution.

43 PARTICLE ACCELERATORS↗

Selective area epitaxy of monolithic white-light InGaN/GaN quantum well microstripes with dual color emission

Monolithic color synthesis is demonstrated using InGaN/GaN multiple quantum wells (QWs) grown on GaN microstripes formed by selective area epitaxy on SiO{sub 2} mask patterns. The striped microfacet structure is composed of (0001) and (11-22) planes, attributed to favorable surface polarity and surface energy. InGaN/GaN QWs on different microfacets contain spatially inhomogeneous compositions owing to the diffusion of adatoms among the facets. This unique property allows the microfacet QWs to emit blue light from the (11-22) plane and yellow light from the top (0001) plane, the mixing of which leads to the perception of white light emission.

42 ENGINEERING↗

Deliverable for FαST project: Ln Resin based PLE

This memo describes the fabrication of a polymer ligand extractant based on Eichrom's LN-1 resin. This work has been in support of the Fast Alpha Spectrometry Tool (FαST) project. The first part of LANL's role in this project is to evaluate new extractants for use in polymer ligand extractants (PLEs). The first new extractant evaluated is Di(2-ethyl hexyl) phosphoric acid (HDEHP), which is an effective metal extractant. It has very efficient chelating properties for a wide variety of metal ions. HDEHP is an amphiphillic molecule with two long hydrocarbon chains and a polar end with a phosphoryl oxygen (P=O) and an acidic -OH group as shown in Figure 1. HDEHP has shown effectiveness in extracting lanthanides, selective actinides, and other trivalent elements. Several authors have reported that lanthanides and elements with +3 oxidation state have similar extraction behavior in nitric acid. The distribution ratio for lanthanides rapidly decreases at lower nitric concentration then start to increase at higher concentration as shown in. The trivalent americium, curium, and yttrium exhibit similar trend as trivalent lanthanides. This extraction trend can be also observed from hydrogen chloride solution. This work describes the use of this ligand in a PLE to extract plutonium from solution. Polymer ligand films were prepared by dissolving HDEHP ligands and polystyrene beads in THF. The solution was directly deposited onto a 40 mm diameter stainless steel substrate using an automated pipette. HDEHP based PLEs with direct stippling method are shown in Figure 2. The solution was air dried at room temperature overnight to ensure complete evaporation of THF. The plutonium tracer solution was prepared in 0.01, 0.1, 1, and 8M nitric solutions to study the effect of nitric concentration in plutonium extraction. 0.1667 Bq 239 Pu tracer solution was directly stippled on each PLE and was allowed to equilibrate for 3 hours before removing the solution. The plutonium activity of each sample was measured by direct alpha counting to quantify the plutonium recovery by HDEHP PLE. The alpha spectra from alpha spectroscopy are shown in Figure 3. 1:5, 1:10, and 1:20 PLEs had sharp peak with low tailing. 1:2 had an extremely long tail, which is a possible indication that a large amount of ligands caused the film to not form a smooth surface. Also, it can be noted that 1:2 ratio PLE surface was not as rigid as the other ratio PLEs and it was prone to scratching during sample handing. The resolution of alpha spectra was quantified by measuring Full Width at Half of the Maximum (FWHM) using Bortels equation. The tailing component of the peak was also measured along with FWHM. The peak resolutions and tailing measurements for 0.1M nitric solution samples are given in Table 1. The best resolution was achieved with 1:5 PLE and worst was given by 1:2 PLE. The plutonium recovery by HDEHP PLE was dependent on both nitric concentration and ligand to polymer ratio. 1:2 PLE consistently had the highest recovery followed by 1:5 as shown in Figure 4. It should be noted that 1:2 ratio PLEs consistently had long tailing and the ROI of the spectrum had to be increased to encompass total counts from the tracer. 1:10 and 1:20 PLEs had close to zero percent recovery in all nitric concentration except for 0.01M. The highest plutonium recovery was observed for 0.1M nitric acid. 1:5 PLE gave the best combination of alpha spectroscopy resolution and plutonium recovery. Radiography image of samples were generated to study the plutonium distribution on the PLE surface. Samples were placed on an imaging plate (Fujifilm BAS-TR 2025) for 24 hours and the plate was scanned using GE Typhoon FLA 7000 system. The radiography image in Figure 5 shows uneven distribution with hot spots along the edge and in the center of the samples. These hot spots may be the result of highly localized concentration of ligands or surface defects that were observed in SEM. This unevenness in distribution may cause inaccurate activity measurement by alpha spectroscopy due to a bias in the energy calibration. PLEs based on HDEHP have been evaluated. The concentration of ligand in polystyrene is critical in the performance of the PLE; both for extraction efficiency as well as for alpha spectrometry results. The optimal PLE using this ligand has a concentration of 1:5 ligand to polystyrene. Under laboratory conditions, this configuration can produce similar results to those obtained for DIPEX based PLEs from previous studies. The concentration is very important to the results obtained for this ligand. This PLE is a good candidate for use in later field studies. Our next report will detail the evaluation of PLEs utilizing crown ether ligands.

36 MATERIALS SCIENCE↗

Final Report: Stability and Novel Properties of Magnetic Materials and Ferromagnet / Insulator Interfaces

We report investigations of the synthesis, structure, and properties of new materials for spintronic applications integrated onto silicon substrates. Our primary focus is materials with very high, negative, intrinsic spin polarization of the density of states at the Fermi level. We have developed a new synthesis method for Fe 3 O 4 thin films through selective oxidation of Fe, resulting in smooth, low-defect density films. We have synthesized Fe4N films and shown that they preferentially oxidize to Fe 3 O 4 . When integrated into magnetic tunnel junctions consisting of Fe4N / AlOx / Fe, oxidation at the Fe4N / AlOx interface creates Fe 3 O 4 , leading to negative tunneling magnetoresistance (TMR). Oxidation of Fe in nominally symmetric CoFe / AlOx / CoFe also produces Fe 3 O 4 and negative TMR under selected oxidation conditions.

36 MATERIALS SCIENCE↗

Capture Cavities for the CW Polarized Positron Source Ce+BAF

The initial design of the capture cavities for the continuous wave (CW) polarized positron beams at Jefferson Lab (Ce+BAF) is presented. A chain of standing wave multi-cell copper cavities inside a solenoid tunnel are selected to bunch/capture positrons. The cavity design strategy is presented to accommodate constrains from the large phase distribution of the incident beams, RF power, radiation and RF heating, beam loading, etc. to improve the capture efficiency. A matrix of design parameters' range are given for future system optimization when the capture cavities are considered together with other sub-systems and beam dynamics. The contents will also be useful for other CW cavity design for beams with large phase space distribution.

Wang, Shaoheng↗

Extreme ultraviolet and X-ray spectroheliograph for OSO-H

A complex scientific instrument was designed, fabricated, tested, and calibrated for launch onboard OSO-H. This instrument consisted of four spectroheliographs and an X-ray polarimeter. The instrument is designed to study solar radiation at selected wavelengths in the X-ray and the extreme ultraviolet ranges, make observations at the H-alpha wavelength, and measure the degree of polarization of X-ray emissions.

Sterk, A. A.↗

Microstrip Antenna Generates Circularly Polarized Beam

Circular microstrip antenna excited with higher order transverse magnetic (TM) modes generates circularly polarized, conical radiation patterns. Found both theoretically and experimentally that peak direction of radiation pattern is varied within wide angular range by combination of mode selection and loading substrate with materials of different dielectric constants.

Huang, J.↗

Universities Earth System Scientists Program

This document constitutes the final technical report for the National Aeronautics and Space Administration (NASA) Grant NAGW-3172. This grant was instituted to provide for the conduct of research under the Universities Space Research Association's (USRA's) Universities Earth System Scientist Program (UESSP) for the Office of Mission to Planet Earth (OMTPE) at NASA Headquarters. USRA was tasked with the following requirements in support of the Universities Earth System Scientists Programs: (1) Bring to OMTPE fundamental scientific and technical expertise not currently resident at NASA Headquarters covering the broad spectrum of Earth science disciplines; (2) Conduct basic research in order to help establish the state of the science and technological readiness, related to NASA issues and requirements, for the following, near-term, scientific uncertainties, and data/information needs in the areas of global climate change, clouds and radiative balance, sources and sinks of greenhouse gases and the processes that control them, solid earth, oceans, polar ice sheets, land-surface hydrology, ecological dynamics, biological diversity, and sustainable development; (3) Evaluate the scientific state-of-the-field in key selected areas and to assist in the definition of new research thrusts for missions, including those that would incorporate the long-term strategy of the U.S. Global Change Research Program (USGCRP). This will, in part, be accomplished by study and evaluation of the basic science needs of the community as they are used to drive the development and maintenance of a global-scale observing system, the focused research studies, and the implementation of an integrated program of modeling, prediction, and assessment; and (4) Produce specific recommendations and alternative strategies for OMTPE that can serve as a basis for interagency and national and international policy on issues related to Earth sciences.

Estes, John E.↗

Studies of Potential Mars Surveyor 1998 Landing Sites

The 1998 lander payload consists of a descent imager, the Mars Volatiles and Climate Surveyor (MVACS) instruments (lander stereo camera, arm-mounted close-up imager, meteorology package, thermal and evolved gas analyzer), and a LIDAR instrument. The mission focuses on assessment of near-surface water ice in the south polar region, and the volatile and climate history of Mars. In order to achieve these objectives, the landing site must allow access to polar layered deposits by the robotic arm, which may be able to dig as much as 0.5 m below the surface. Hence, the presence of recent aeolian debris at the landing site may adversely affect the ability of the MVACS instruments to gather the samples and acquire data needed to properly address the science objectives. The studies described here include mapping surface units in the landing region (73S - 77S, 140W - 230W) to infer the distribution of aeolian debris and to identify potential landing sites where mantling is minimal. Because the '98 lander will not be able to survive very low temperature conditions, this study also includes mapping of south polar seasonal frost retreat based on Viking Orbiter images. The results of this work, in conjunction with complementary studies by other investigators, will facilitate the selection of the Mars Surveyor 1998 landing site (and backup) by the summer of 1998.

Herkenhoff, K. E.↗

Fiber Laser Development for LISA

We have developed a linearly-polarized Ytterbium-doped fiber ring laser with single longitudinal-mode output at 1064nm for LISA and other space applications. Single longitudinal-mode selection was achieved by using a fiber Bragg grating (FBG) and a fiber Fabry-Perot (FFP). The FFP also serves as a frequency-reference within our ring laser. Our laser exhibits comparable low frequency and intensity noise to Non-Planar Ring Oscillator (NPRO). By using a fiber-coupled phase modulator as a frequency actuator, the laser frequency can be electro-optically tuned at a rate of 100kHz. It appears that our fiber ring laser is promising for space applications where robustness of fiber optics is desirable.

Numata, Kenji↗

Programmable Phase Selection between Altermagnetic and Noncentrosymmetric Polymorphs of MnTe on InP via Molecular Beam Epitaxy

Phase selecting nearly degenerate crystalline polymorphs during epitaxial growth can be challenging yet critical to targeting physical properties for specific applications. Here, we establish how phase selectivity of altermagnetic and noncentrosymmetric polymorphs of MnTe can be programmed by subtle changes to the surface of lattice-matched InP substrates in molecular beam epitaxy growth. Bulk altermagnetic MnTe is thermodynamically stable in the hexagonal NiAs-structure and is synthesized here on the polar (111)A surface (In-terminated) of InP, while the noncentrosymmetric, cubic ZnS-structure with wide band gap (>3 eV), which epitaxially matches III–V materials, is stabilized on the (111)B surface (P-terminated). Electron microscopy, X-ray photoemission spectroscopy, and reflection high-energy electron diffraction indicate that phase selection is triggered at the interface and proceeds along the growing surface. First-principles calculations suggest that interfacial termination and strain have a significant effect on the interfacial energy; stabilizing the NiAs polymorph on the In-terminated surface and the ZnS structure on the P-terminated surface. Here, selectively grown, high-quality, phase pure films of both MnTe polymorphs will enable our understanding of the novel properties of these materials, thereby facilitating their use in new applications ranging from spintronics to microelectronic devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗