Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “mixture experiment models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Super-swelling behavior of stacked lipid bilayer systems

Bilayer systems comprising lipid mixtures are the most well-studied model of biological membranes. While the plasma membrane of the cell is a single bilayer, many intra- and extra-cellular biomembranes comprise stacks of bilayers. Most bilayer stacks in nature are periodic, maintaining a precise water layer separation between bilayers. That equilibrium water separation is governed by multiple inter-bilayer forces and is highly responsive. Biomembranes re-configure inter-bilayer spacing in response to temperature, composition, or mass transport cues. In synthetic bilayer systems for applications in cosmetics or topical treatments, control of the hydration level is a critical design handle. Herein we investigate a binary lipid system that leverages key inter-bilayer forces leading to unprecedented levels of aqueous swelling while maintaining a coherent multilamellar form. We found that combining cationic lipids with bicontinuous cubic phase-forming lipids (lipids with positive Gaussian modulus), results in the stabilization of multilamellar phases against repulsive steric forces that typically lead to bilayer delamination at high degrees of swelling. Using ultra-small-angle X-ray scattering alongside confocal laser scanning microscopy, we characterized various super-swelled states of 1,2-dioleoyl-3-trimethylammonium-propane (DOTAP) and glycerol monooleate (GMO) lipids, as well as other analogous systems, at varied concentration and molar ratios. Through these experiments we established swelling profiles of various binary lipid systems that were near-linear with decreasing lipid volume fraction, showing maximum swelling with periodicity well above 200 nanometers.

42 ENGINEERING↗

Investigation and modeling of the degradation of zirconium-based fuel cladding during corrosion in steam and air-steam mixtures at high temperatures - 2016-0033

This paper presents the main results of a study conducted to quantify and to model the degradation state of zirconium-based fuel claddings submitted to severe-accident conditions in a nuclear reactor core: high temperatures and either pure steam or an air-steam mixture. Due to the progressive thickening of a dense and protective ZrO{sub 2} layer, the oxidation kinetics of zirconium-based claddings in steam at high temperatures typical of severe nuclear accidents are generally cubic or parabolic. However, for some temperature domains, this oxide layer may crack, becoming porous and no longer protective. In these 'breakaway' conditions, the oxidation kinetics change from (sub)parabolic to linear or even accelerated. In addition, the temperature increase can lead core materials to melt and to relocate down to the vessel lower head, threatening its integrity. If it fails, and for specific conditions, air ingress may take place into the reactor. Hence, oxygen and nitrogen both react with zirconium-based claddings successively through the oxidation of zirconium (forming a ZrO{sub 2} layer), nitriding of zirconium (forming zirconium nitride particles), and the oxidation of zirconium nitride (forming ZrO{sub 2} and releasing nitrogen). These self-sustained chemical reactions enhance the deterioration of zirconium-based claddings and their ZrO{sub 2} layers, inducing an increase in their open porosity. To quantify this porosity, a series of two-step experiments was conducted. First, ZIRLO{sup TM} cladding samples were isothermally oxidized in pure steam or in a 50:50 mol% air-steam mixture at several different temperatures and durations. The main thermal effects on reaction kinetics and the high impact of air on the cladding degradation were all confirmed by experimental results. Second, pioneering porosimetry measurements by mercury intrusion were realized for the first time on such corroded cladding samples. In both atmospheres, it was pointed out that 1,200 and 1,250 K led to particularly porous oxide layers, especially due to strong breakaway effects. Moreover, we confirmed that the presence of air strongly enhances the oxide cracking: cladding samples were more porous when oxidized in the air-steam mixture than under pure steam. Finally, we observed that in all conditions, the open porous volume fraction of ZIRLO claddings continuously rose during their corrosion process. Hence, for each experimental condition, porosity correlations were determined through linear regressions, and porosity increase rates were deduced by derivation versus time and validated against porosimetry results of cladding samples corroded in transient nonisothermal) conditions. (authors)

36 MATERIALS SCIENCE↗

Minority Serving Institutions Partnership Program (MSIPP) - 18108

The DOE-EM recognizes that successfully completing its legacy environmental cleanup mission will require maintaining a well-trained, technically skilled, and diverse workforce. Minority representation in critical science and engineering fields is an important part of EM's vision for the future workforce. The Minority Serving Institutions Partnership Program (MSIPP) has been created and designed to increase the numbers of minorities with science and engineering experience in areas important to the success of the DOE-EM mission. MSIPP will provide financial assistance for science, technology, engineering, and mathematics (STEM) activities at Minority Serving Institutions (MSI) engaged in research and related STEM efforts supporting EM's needs. The program offers research internship opportunities at DOE National Laboratories across the DOE complex. MSIPP also encourages research collaborations between MSI Universities and DOE National Laboratories by funding research in areas relevant to DOE-EM needs. Based on current DOE-EM missions, there are two research focus areas: Tank Waste and Site Restoration. Tank Waste includes priority areas of current DOE tank waste and waste processing approaches, alternative DOE tank waste processing options, and tank management and closure. Site Restoration research concentrates in the areas of Soil and Groundwater with priority areas of attenuation-based remedies for the subsurface, deep vadose zone, remediation of mercury and industrial contaminants, and advanced simulation capability for environmental management; and, in the areas of Deactivation and Decommissioning, with priority areas of unique sensor networks for remote monitoring of entombed facilities and tanks, interactions between radiological and chemical contaminants of concern to DOE and facility materials, incombustible fixatives and decontamination agents, acceptability of DeconGel and various contaminant mixtures and robotics, remote systems with plug-and-play interchangeable components, and models for facility decommissioning. This paper gives an overview of the opportunities available to MSI students and universities and outlines the progress this program has made since its inception, and the path forward to further enhance efforts to create a pipeline into the DOE-EM workforce. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Flow Visualization, Heat Transfer, and Critical Heat Flux of Flow Boiling in Earth Gravity with Saturated Liquid-Vapor Mixture Inlet Conditions – In Preparation for Experiments Onboard the International Space Station

This study investigates flow boiling of n-Perfluorohexane with saturated two-phase mixture inlet in a rectangular channel of dimensions 114.6-mm heated length, 2.5-mm width, and 5 mm-height. The experiments were performed as part of the Mission Sequence Testing of the Flow Boiling and Condensation Experiment’s (FBCE) Flow Boiling Module (FBM) in the vertical upflow configuration in Earth gravity using the same experimental system that was launched to the International Space Station (ISS) in August 2021. The operating parameters varied are heating configuration (single- and double-sided), mass velocity (380 – 2400 kg/m2s), inlet quality (0.011 – 0.519), and inlet pressure (120 – 179 kPa). High-speed video photographs are presented to explain the two-phase flow patterns within the channel’s heated length. Flow patterns are constituted by low-density and high-density fronts moving along the channel, with the high-density fronts gradually reducing in length due to evaporation. Heat transfer results in terms of flow boiling curves, streamwise wall temperature profiles, streamwise heat transfer coefficient profiles, and average heat transfer coefficients are presented and trends discussed. CHF data from the present experiments are combined with prior databases to compile a consolidated FBCE-CHF database for saturated inlet to expand the ranges of operating conditions and include other flow orientations in Earth gravity. Experimental CHF trends are also discussed. The interfacial lift-off model shows a good CHF predictive accuracy evidenced by a mean absolute error of 11.97% for this consolidated database after constraining it to mass velocities greater than or equal to 500 kg/m2s. Finally, this study confirmed reliability of the upcoming ISS experiments for saturated inlet conditions and the collected Earth-gravity data will be compared to ISS microgravity data.

Flow boiling↗

Fast redox switches lead to rapid transformation of goethite in humid tropical soils: A Mössbauer spectroscopy study

Abstract Humid tropical forest soils experience frequent rainfall, which limits oxygen diffusion and creates redox heterogeneity in upland soils. In this study we gauged the effect of short‐term anoxic conditions on Fe mineralogy of relatively Fe‐ and C‐rich surface soils (C/Fe mole ratio ∼5) from a humid tropical forest in Puerto Rico. Soils subjected to 4‐d oxic/anoxic oscillation were characterized by selective chemical extractions, Mössbauer spectroscopy (MBS), and X‐ray diffraction. Chemical extraction data suggested that rapidly switching redox conditions had subtle effects on bulk Fe mineralogy. Mössbauer, on the other hand, indicated that (a) the soil Fe is a mixture of goethites of varying characteristics with minor contributions from ferrihydrite (<5%) and Fe(III)‐organic matter (OM) phases (∼10%), and (b) anoxic conditions rapidly transformed all forms of goethite to relatively stable Fe oxides. Such fast changes in goethite features could be due to rapid depletion and sorption of bio‐released structural Al or sorbed OM onto residual soil components. The rapid temporal changes in MBS parameters and corresponding pore water nominal oxidation state of C values suggest that Fe‐C transformations in these upland tropical soils are complex and intricately coupled. A comprehensive understanding of the fate of Fe, Al, and OM (Fe‐organic moieties) during redox switches and concurrent changes in pore water chemistry is critical for development of robust transport models in humid tropical soils, which are subject to episodic low‐redox events.

54 ENVIRONMENTAL SCIENCES↗

Property Measurements of NaCl-UCl 3 and LiF-NaF-KF Molten Salts Doped with Surrogate Fission Products

Knowing thermophysical and thermochemical property values of salts over the expected range of operating temperatures is essential to modeling and simulation efforts that support the commercialization of molten salt reactor (MSR) technologies. Salt properties being measured at Argonne include thermal transitions, phase behavior, heat capacity, density, surface tension, volumetric thermal expansion, thermal diffusivity, thermal conductivity, and viscosity. The properties of several salts of interest including NaCl-UCl 3 and LiF-NaF-KF (FLiNaK) have been measured at Argonne and reported previously. These property measurements are suitable for use in evaluating reactor performance during startup and the early operating life of the reactor. The physical and chemical behavior of the fuel salt is altered by the buildup of fission products and the resulting changes in heat transfer and other properties must be understood by reactor developers. This report summarizes melting behavior, heat capacity, and thermal diffusivity values that were measured for mixtures of FLiNaK and NaCl-UCl 3 salts that have been doped with surrogate fission products. Additional heat capacity measurements were also performed on a separate mixture of FLiNaK without dopants. Measured properties are suitable for incorporation into the Molten Salt Thermal Properties Database–Thermochemical (MSTDB–TC) and the Molten Salt Thermal Properties Database–Thermophysical (MSTDB–TP) to support the development of MSRs. Salts were prepared by doping eutectic mixtures of NaCl-UCl 3 and FLiNaK with surrogate fission products. These salts were prepared for use in salt spill experiments being performed at Argonne and were subsequently used for thermal property measurements. Thermal transitions and heat capacities were measured by using differential scanning calorimetry (DSC) and thermal diffusivity was measured by using laser flash analysis (LFA) at temperatures spanning the typical MSR operating range. The measured property values of the doped salts were compared to measured property values of salts without fission products to quantify the effects of the doped fission products.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Transient Kinetic Experiments within the High Conversion Domain: The Case of Ammonia Decomposition

In the development of catalytic materials, a set of standard conditions is needed where the kinetic performance of many samples can be compared. This can be challenging when a sample set covers a broad range of activity. Precise kinetic characterization requires uniformity in the gas and catalyst bed composition. This limits the range of convecting devices to low conversion (generally <20%). While steady-state kinetics offer a snapshot of conversion, yield and apparent rates of the slow reaction steps, transient techniques offer much greater detail of rate processes and hence more information as to why certain catalyst compositions offer better performance. In this work, transient experiments in two transport regimes are compared: an advecting differential plug flow reactor (PFR) and a pure-diffusion temporal analysis of products (TAP) reactor. The decomposition of ammonia was used as a model reaction to test three simple materials: polycrystalline iron, cobalt and a bimetallic preparation of the two. These materials presented a wide range of activity and it was not possible to capture transient information in the advecting device for all samples at the same conditions while ensuring uniformity. We push the boundary for the theoretical estimates of uniformity in the TAP device and find reliable kinetic measurement up to 90% conversion. However, what is more advantageous from this technique is the ability to observe the time-dependence of the reaction rate rather than just singular points of conversion and yield. For example, on the iron sample we observed reversible adsorption of ammonia and on cobalt materials we identify two routes for hydrogen production. From the time-dependence of reactants and product, the dynamic accumulation was calculated. This was used to understand the atomic distribution of H and N species regulated by the surface of different materials. When ammonia was pulsed at 550 °C, the surface hydrogen/nitrogen, (H/N), ratios that evolved for Fe, CoFe and Co were 2.4, 0.25 and 0.3 respectively. This indicates that iron will store a mixture of hydrogenated species while materials with cobalt will predominantly store NH and N. While much is already known about iron, cobalt and ammonia decomposition, the goal of this work was to demonstrate new tools for comparing materials over a wider window of conversion and with much greater kinetic detail. As a result, this provides an approach for detailed kinetic discrimination of more complex industrial samples beyond conversion and yield.

36 MATERIALS SCIENCE↗

Biogeochemistry of Two Types of Permeable Reafctive Barriers, Organic Carbon and Iron-bearing Organic Carbon for Mine Drainage treatment: Column experiments

Permeable reactive barriers (PRBs) are an alternative technology to treat mine drainage containing sulfate and heavy metals. Two column experiments were conducted to assess the suitability of an organic carbon (OC) based reactive mixture and an Fe{sup 0}-bearing organic carbon (FeOC) based reactive mixture, under controlled groundwater flow conditions. The organic carbon mixture contains about 30% (volume) organic carbon (composted leaf mulch) and 70% (volume) sand and gravel. The Fe{sup 0}-bearing organic carbon mixture contains 10% (volume) zero-valent iron, 20% (volume) organic carbon, 10% (volume) limestone, and 60% (volume) sand and gravel. Simulated groundwater containing 380 ppm sulfate, 5 ppm As, and 0.5 ppm Sb was passed through the columns at flow rates of 64 (the OC column) and 62 (the FeOC column) ml d{sup -1}, which are equivalent to 0.79 (the OC column) and 0.78 (the FeOC column) pore volumes (PVs) per week or 0.046 m d{sup -1} for both columns. The OC column showed an initial sulfate reduction rate of 0.4 {mu}mol g (OC){sup -1} d{sup -1} and exhausted its capacity to promote sulfate reduction after 30 PVs, or 9 months of flow. The FeOC column sustained a relatively constant sulfate reduction rate of 0.9 {mu}mol g (OC){sup -1} d{sup -1} for at least 65 PVs (17 months). In the FeOC column, the {delta}34S values increase with the decreasing sulfate concentration. The {delta}34S fractionation follows a Rayleigh fractionation model with an enrichment factor of 21.6%. The performance decline of the OC column was caused by the depletion of substrate or electron donor. The cathodic production of H{sub 2} by anaerobic corrosion of Fe probably sustained a higher level of SRB activity in the FeOC column. These results suggest that zero-valent iron can be used to provide an electron donor in sulfate reducing PRBs. A sharp increase in the {delta}13C value of the dissolved inorganic carbon and a decrease in the concentration of HCO{sub 3}{sup -} indicate that hydrogenotrophic methanogenesis is occurring in the first 15 cm of the FeOC column.

36 MATERIALS SCIENCE↗

Microwave N{sub 2}-Ar plasma torch. II. Experiment and comparison with theory

Spatially resolved emission spectroscopy techniques have been used to determine the gas temperature, the electron, and N{sub 2}{sup +} ion densities and the relative emission intensities of radiative species in a microwave (2.45 GHz) plasma torch driven by a surface wave. The experimental results have been analyzed in terms of a two-dimensional theoretical model based on a self-consistent treatment of particles kinetics, gas dynamics, and wave electrodynamics. The measured spatial variations in the various quantities agree well with the model predictions. The radially averaged gas temperature is around 3000 K and varies only slowly along the discharge zone of the source but it drops sharply down to about 400 K in the postdischarge. The experimental wave dispersion characteristics nearly follow the theoretical ones, thus confirming that this plasma source is driven by a surface wave.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Enhancing $\phi$-sensitivity of ignition delay times through dilution of fuel-air mixture

The high $\phi$-sensitivity (η) of ignition delay time (τ IDT ) is one of the desirable fuel properties for the high-load extension of advanced compression ignition engine. Recent studies revealed the effectiveness of a high dilution rate (x D ) for enhancing η at the engine-relevant conditions. This study aims to quantify the effect of dilution on the η of isooctane using a combined experiment-simulation approach. The ignition delay of the isooctane/air mixture was measured with an Advanced Fuel Ignition Delay Analyzer (AFIDA) over the temperature range of 623 - 923 K at 10 bar pressure with global $\phi$ = 0.3 - 0.6, with and without 28.6% of additional N 2 dilution. For precise evaluation of experimental η, the facility effect of the AFIDA experiment was characterized with three-dimensional computational fluid dynamics (3-D CFD) simulation. The temperature in the combustion chamber from 3-D CFD indicated a substantial temporal dependency, varying up to ~52 K by charge-cooling of fuel injection and heat transfer from the wall. We introduced the dimensionless number θ(t) for characterizing the temporal profile of chamber temperature. Consideration of the facility effect using θ(t) resulted in better agreement between the experimental ..eta.. and zero-dimensional (0-D) kinetics simulation. The refined η were then further utilized to quantify the effectiveness of dilution to η The extent of η enhancement with dilution strategy was maximized at the low-temperature chemistry regime, increasing η by 77% with a 28.6% dilution rate. Further analysis on the dilution effect was carried out using 0-D kinetics simulation, revealing the critical dimensionless numbers relevant to the effectiveness of dilution to η enhancement. Here, this study is the first experiment-simulation combined research to quantify the effect of dilution on η, facilitating the kinetics model refinement for better reproduction of $\phi$-sensitivity.

33 ADVANCED PROPULSION SYSTEMS↗

Discrete models of fluids: spatial averaging, closure and model reduction

We consider semidiscrete ODE models of single-phase fluids and two-fluid mixtures. In the presence of multiple fine-scale heterogeneities, the size of these ODE systems can be very large. Spatial averaging is then a useful tool for reducing computational complexity of the problem. The averages satisfy exact balance equations of mass, momentum, and energy. These equations do not form a satisfactory continuum model because evaluation of stress and heat flux requires solving the underlying ODEs. To produce continuum equations that can be simulated without resolving microscale dynamics, we recently proposed a closure method based on the use of regularized deconvolution. Here we continue the investigation of deconvolution closure with the long term objective of developing consistent computational upscaling for multiphase particle methods. The structure of the fine-scale particle solvers is reminiscent of molecular dynamics. For this reason we use nonlinear averaging introduced for atomistic systems by Noll, Hardy, and Murdoch-Bedeaux. We also consider a simpler linear averaging originally developed in large eddy simulation of turbulence. We present several simple but representative examples of spatially averaged ODEs, where the closure error can be analyzed. Based on this analysis we suggest a general strategy for reducing the relative error of approximate closure. For problems with periodic highly oscillatory material parameters we propose a spectral boosting technique that augments the standard deconvolution and helps to correctly account for dispersion effects. We also conduct several numerical experiments, one of which is a complete mesoscale simulation of a stratified two-fluid flow in a channel. In this simulation, the operation count per coarse time step scales sublinearly with the number of particles.

Multiscale modeling, discrete models, fluid flow↗

3D modeling of the Staged Z-pinch with the FLASH code

The Staged Z-pinch (SZP) fusion concept is a magneto-inertial compression scheme developed by Magneto-Inertial Fusion Technologies, Inc. (MIFTI), in which small amounts of fusion fuel are brought to fusion-relevant conditions by passing multi-million amperes strong current through a cylindrical shell of high atomic number material. One- and two-dimensional modeling performed by MIFTI with the MACH2 code, suggests that net fusion energy gain can be achieved when currents in the 10 million amperes range compress a 50%-50% mixture of deuterium and tritium gas. In this project we enhance and use the FLASH code to execute high-fidelity, simulations of various SZP configurations, a collaboration between the Flash Center for Computational Science at the University of Rochester and the Laboratory for Laser Energetics, and MIFTI. FLASH is a high-performance computing, multi-physics, radiation magnetohydrodynamic (MHD) code with extended physics capabilities, which is developed at the Flash Center. The goal of this project is to assess the shell/fuel stability of the pinch to two- and three-dimensional MHD instabilities and to utilize FLASH’s extended physics capabilities to understand how extended-MHD effects impact implosion dynamics and plasma conditions at stagnation. The project is a natural extension of an ongoing collaborative effort between MIFTI and the Flash Center through the U.S. DOE Advanced Research Projects Agency-Energy (ARPA-E) BETHE program and can provide MIFTI with simulation capabilities that are currently beyond their reach with MACH2. Ultimately, MIFTI wants FLASH to become one of their simulation workhorses for reliable, high-fidelity SZP platform design. During the project, the Flash Center team developed a suite of in one- and two-dimensional FLASH simulations to model different variants of the SZP platform, performed code-to-code comparisons with MACH2, and used the FLASH code to design and model SZP experiments like the Double Eagle experiments that MIFTI recently performed. Also, the Flash Center team developed the capabilities of FLASH to be able to do three-dimensional simulations of pulsed-power experiments with the code for the first time. Two publications from this effort are currently under review and two more are in preparation. MIFTI has also committed to the use of FLASH for future SZP simulation efforts.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Laboratory differential simulation design method of pressure absorbers for carbonization of phenolate solution by carbon dioxide in coal-tar processing

A laboratory differential simulation method is used for the design of carbonization columns at coal-tar processing in which phenols are regenerated from phenolate solution by carbon dioxide absorption. The design method is based on integration of local absorption rates of carbon dioxide along the column. The local absorption rates into industrial phenolate mixture are measured in a laboratory model contactor for various compositions of the gas and liquid phases under the conditions that ensure the absorption rates in the laboratory absorber simulate the local rates in the industrial column. On the bases of the calculations, two-step carbonization columns were designed for 30000 t/year of the phenolate solution treatment by carbon dioxide. The absorption proceeds at higher pressure of 500 kPa and temperatures from 50 to 65 C, pure carbon dioxide is used and toluene is added. These conditions have the following favourable effects: (I) significant size reduction of the columns, (ii) it is possible to process more concentrated solutions without danger of silting the columns by crystallization of NaHCO{sub 3} on the packing. (iii) small amount of inert gas is released, (iv) lower alkalinity and better separability of the organic phase (phenols with toluene) from water phase (soda or bicarbonate solution) in separators.

01 COAL, LIGNITE, AND PEAT↗

Continuum model of irradiation-induced spinodal decomposition in the presence of dislocations

A model of phase-separation kinetics in systems exposed to energetic particle irradiation has been extended to include the effects of mobile dislocations. It is shown that when dislocations are allowed to participate in the decomposition reaction, phase separation can occur at temperatures above the coherent spinodal, which is in agreement with several experiments on irradiated alloys. A linear stability analysis of the governing kinetic equations is performed and three regimes of microstructural evolution are identified within the parameter space of damage cascade size vs incident flux: complete phase separation, solid-solution behavior, and compositional patterning. In addition, numerical simulations of the evolving dislocation density and composition fields are performed. The numerical results provide the amplitude and wavelength of the stable patterns that can form under irradiation and elucidate the role of misfit dislocations in reducing the coherency strain due to atomic size mismatch.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of Hydrogen on Steady-State and Transient Combustion Instability Characteristics

This paper examines the effects of steady-state and transient hydrogen enrichment on thermoacoustic instability in a model gas turbine combustor. Combustion instability, a feedback loop between flame heat release rate oscillations and combustor acoustics, is characterized in a swirl-stabilized flame operated at a range of hydrogen–natural gas fuel blends and heat rates. Measurements of combustor chamber pressure fluctuations and CH* chemiluminescence imaging are used to characterize instability at a range of operating conditions. Steady-state tests show that both mixture heat rate and hydrogen content affect system stability. At a given heat rate, higher levels of hydrogen result in unstable combustion. As heat rate increases, instability occurs at lower concentrations of hydrogen in the fuel. Transient operation was tested in two directions—instability onset and decay—and two hydrogen-addition times—a short time of 1 ms and a longer time of 4 s. Results show that instability onset processes, through the transient addition of hydrogen, are highly repeatable regardless of the timescale of hydrogen addition. Certain instability decay processes are less repeatable, resulting in cases that do not fully transition from unstable to stable combustion despite similar changes in hydrogen fuel flow rate. Flame behavior before, during, and after the transient is characterized using high-speed CH* chemiluminescence imaging. Analysis of the high-speed images shows changes in flame stabilization and dynamics during the onset and decay processes. Finally, the results of this study can have implications for systems that experience variations in fuel composition, particularly in light of growing interest in hydrogen as a renewable fuel.

42 ENGINEERING↗

A Numerical and Experimental Study of Coflow Laminar Diffusion Flames: Effects of Gravity and Inlet Velocity

In this work, the influence of gravity, fuel dilution, and inlet velocity on the structure, stabilization, and sooting behavior of laminar coflow methane-air diffusion flames was investigated both computationally and experimentally. A series of flames measured in the Structure and Liftoff in Combustion Experiment (SLICE) was assessed numerically under microgravity and normal gravity conditions with the fuel stream CH4 mole fraction ranging from 0.4 to 1.0. Computationally, the MC-Smooth vorticity-velocity formulation of the governing equations was employed to describe the reactive gaseous mixture; the soot evolution process was considered as a classical aerosol dynamics problem and was represented by the sectional aerosol equations. Since each flame is axisymmetric, a two-dimensional computational domain was employed, where the grid on the axisymmetric domain was a nonuniform tensor product mesh. The governing equations and boundary conditions were discretized on the mesh by a nine-point finite difference stencil, with the convective terms approximated by a monotonic upwind scheme and all other derivatives approximated by centered differences. The resulting set of fully coupled, strongly nonlinear equations was solved simultaneously using a damped, modified Newton's method and a nested Bi-CGSTAB linear algebra solver. Experimentally, the flame shape, size, lift-off height, and soot temperature were determined by flame emission images recorded by a digital camera, and the soot volume fraction was quantified through an absolute light calibration using a thermocouple. For a broad spectrum of flames in microgravity and normal gravity, the computed and measured flame quantities (e.g., temperature profile, flame shape, lift-off height, and soot volume fraction) were first compared to assess the accuracy of the numerical model. After its validity was established, the influence of gravity, fuel dilution, and inlet velocity on the structure, stabilization, and sooting tendency of laminar coflow methane-air diffusion flames was explored further by examining quantities derived from the computational results.

microgravity↗

High Semi-Volatile Organic Aerosol Contributions Associated with Ammonium Nitrate in the Coastal Urban Environment

Organic components often contribute 50% or more of the submicron aerosol mass in coastal urban environments, but their partitioning between the gas and particle phases is controlled by a complex mixture of unidentified organic compounds that are poorly constrained by observations. This study compares daily filter organic functional groups (OFG) with online organic mass fragments from La Jolla, California, as part of the Eastern Pacific Cloud Aerosol Precipitation Experiment (EPCAPE), quantifying the contributions of four types of non-volatile (NV) organic emission sources to the submicron composition. Daily filters retained only 0.79–0.98 µg/m3 NV submicron organic mass concentration, even though 1.8–1.9 µg/m3 non-refractory (NR) submicron organic mass concentration was measured online. The 62–64% of measured NR submicron organic mass concentration that exceeded what remained on the filters after 23-hr sampling is interpreted as semi-volatile, consistent with the moderate correlation of the NR NV difference to NR ammonium, NR nitrate, and biomass burning-related NV and NR organic factors. The association between semi-volatile organic components and ammonium nitrate likely results from both co-emission and co-evaporation. Size-resolved filter analysis showed that NV organic mass concentration accounts for 68% of NR organic mass concentration for 0.5–1 µm dry diameter but account for 9.0% for 0.18–0.5 µm dry diameter showing the differences in volatility between particle modes. Importantly, volatility of organic components was size-dependent Information Classification: General and associated with ammonium nitrate and biomass burning, providing guidance for constraining atmospheric aerosol properties in global models.

Pelayo, Christian↗

Gap Size Uncertainty Quantification in Advanced Gas Reactor TRISO Fuel Irradiation Experiments

The Advanced Gas Reactor (AGR)-3/4 experiment is the combination of the third and fourth tests conducted within the tristructural isotropic fuel development and qualification research program. The AGR-3/4 test consists of twelve independent capsules containing a fuel stack in the center surrounded by three graphite cylinders and shrouded by a stainless steel shell. This capsule design enables temperature control of both the fuel and the graphite rings by varying the neon/helium gas mixture flowing through the four resulting gaps. Knowledge of fuel and graphite temperatures is crucial for establishing the functional relationship between fission product release and irradiation thermal conditions. These temperatures are predicted for each capsule using the commercial finite-element heat transfer code ABAQUS. Uncertainty quantification reveals that the gap size uncertainties are among the dominant factors contributing to predicted temperature uncertainty due to high input sensitivity and uncertainty. Gap size uncertainty originates from the fact that all gap sizes vary with time due to dimensional changes of the fuel compacts and three graphite rings caused by extended exposure to high temperatures and fast neutron irradiation. Gap sizes are estimated using as-fabricated dimensional measurements at the start of irradiation and post irradiation examination dimensional measurements at the end of irradiation. Uncertainties in these measurements provide a basis for quantifying gap size uncertainty. However, lack of gap size measurements during irradiation and lack of knowledge about the dimension change rates lead to gap size modeling assumptions, which could increase gap size uncertainty. In addition, the dimensional measurements are performed at room temperature, and must be corrected to account for thermal expansion of the materials at high irradiation temperatures. Uncertainty in the thermal expansion coefficients for the graphite materials used in the AGR-3/4 capsules also increases gap size uncertainty. This study focuses on analysis of modeling assumptions and uncertainty sources to evaluate their impacts on the gap size uncertainty.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗