Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “mechanical properties testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Durability of plasma sprayed Thermal Barrier Coatings with controlled properties part Ⅱ: Effects of geometrical curvature

The present investigation elucidates the effects of substrate curvature on the durability of Air Plasma Sprayed (APS) Thermal Barrier Coatings (TBCs). Traditionally, planar disk specimens are utilized in Furnace Cycle Testing (FCT). In most cases, delamination is initiated at the disk's free edge and then propagates along the TBC-bond coat interface. However, in turbine components (e.g., blades/vanes), they lack significant free edges and the coatings are deposited on non-flat surfaces of varying radii of curvature. These geometrical discrepancies imply significant differences in the stress states as compared to planar disk specimens. Therefore, the part geometry inevitably affects the TBC failure mechanisms in the turbine system, and consequently influences TBC durability. Nevertheless, these effects have not been fully explored in the past, despite the anecdotal knowledge which suggests the leading edge of turbine blades to be one of the most common failure/spallation locations. Here in this study, representative TBC systems were deposited onto superalloy disks with flat substrate and rods with curved substrate. The experimental results from FCT suggest TBC durability on rods is significantly lower than when sprayed on disks. Furthermore, the durability of TBCs on rods appears to increase with higher porosity, which is contradictory to reported trends for TBCs on disks. In addition, the effects of various bond coats are not consistent with those observed in disks. To clarify the underlying effects of curved geometries, detailed stress analyses were performed. They revealed a state of thermal stresses which is unique to curved geometries. It was found that TBC on rods experience tensile radial stresses as well as tensile hoop stresses during the cooling. These stresses result in a complex interplay in failure processes in rods, which explains the different observed trends in the durability from those obtained with disks.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Reversible Physical Gelation of Thermotropic Liquid Crystals Driven by Nanoplate Self-Assembly

Physically gelled soft materials, driven by the self-assembly of low-molecular-mass gelators (LMGs), have emerged as a platform for designing advanced gels that exhibit reversible gelation and property tunability. Liquid crystal (LC) gels are of great interest due to their supramolecular orderings as gel hosts and their enhanced electro-optical properties. In this study, we demonstrate the physical gelation of a nematic LC driven by nanoplate self-assembly, expanding the concept of gelators from small molecules to nanoparticles. These nanoplates are functionalized with promesogenic ligands and form a fibrillar network in LCs with face-to-face interplate stacking, resembling LMGs. The critical gelation volume fraction in the tilt test is only 0.14 v %, comparable to values reported for LMGs. Rheological analyses confirm viscoelastic properties characteristic of gelation. In situ small-angle X-ray scattering (SAXS) characterizes the formation of nanoplate networks in the LC with decreasing temperature, wherein LC mesogens become trapped in pores. Molecular dynamics (MD) simulations reveal that the interaction between ligand-coated nanoplates and LC-forming mesogens induces a multidomain LC structure, increasing friction between LC domains and stabilizing the gel. This study establishes direct relationships among molecular interactions, nanostructures, and mechanical properties in physically gelled LCs. In conclusion, the findings inspire the future gelator design of both LMGs and nanoplates, with potential applicability in bioscaffold engineering and liquid crystalline nanocomposites.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Conceptual Design of Temperature-Controlled Fueled-Salt Irradiation Experiment to Support Demonstration of Advanced Nuclear Reactors

The irradiation testing of fuel-bearing molten salts is critical to supporting the development and demonstration of molten salt reactors (MSRs). These experiments can inform several important reactor design and safety parameters, including source term modeling, evolution of thermophysical properties with burn-up, and the degradation of structural materials under reactor relevant conditions. Idaho National Laboratory is designing an instrumented and heated high temperature molten salt-fueled irradiation capsule to study the behavior of the fuel salt during in-pile irradiation. This paper details the neutronics, thermal, and mechanical analysis performed to-date. Parametric studies are performed to assess a range of material, different experiment dimensions, two in-reactor positions, and the fuel enrichment used. Principal recommendations are to opt for a peripheral reactor position to alleviate neutronic constraints, a thin salt annulus to alleviate thermal constraints, and high-temperature alloys that provide additional safety margins.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Durable and Low-Cost Fractal Structured Multifunctional Coatings for Next-Generation CSP

Fractal coatings on various low-cost and high-temperature metallic substrates such as SS316, SS347, In800H, In740H, In625, Haynes 230, etc. were fabricated employing our patented novel electrodeposition process at various deposition potentials and deposition times, as well as chemical etching. The best combination of the materials and processing conditions were co-optimized for the reliable and repeatable fabrication of the multifunctional coatings. Surface morphologies were examined using SEM and AFM, and fractal characterization was done using a 3D optical surface profiler. Fractal dimension was used to identify successful fabrication and material parameters. The mechanical durability of the coatings was evaluated using several standardized tests, such as sand abrasion (ASTM D968) and adhesion (ASTM D3359), to fully characterize and demonstrate the mechanical durability of the fabricated surfaces. HTF immersion tests on the fractal multifunctional coatings were conducted based on a modification of the ASTM D870, which is established for static water immersion testing. To calculate the corrosion rates and descaled weight loss of the samples subjected to thermal exposure for different time durations (100 h, 300 h, 500 h, and optionally 750 h) to estimate the corrosion rate. While protecting the substrates from corrosion is an important goal, an allied goals is also to examine the post-corrosion temperature stability and properties of the molten salts themselves due to the dissolution of the constituents of the alloys and the corrosion products from the coatings that cause “fouling” of the molten salts. Fouling characteristics of the different molten salt HTFs exposed to coated and uncoated substrates were investigated. Finally, considering a prototype molten salt/sCO2 heat exchanger, cost/performance model is developed to demonstrate that the coatings on low-cost alloys such as stainless steel provide lower levelized cost of heat exchanger compared to high nickel content Ha230.

14 SOLAR ENERGY↗
DOE OSTI2025

The Effects of Manufacturing Techniques on Neutron-Irradiated C26M Mechanical Properties

Nuclear energy provides 13% of the total energy produced globally. To further improve the safety and reliability of nuclear reactors material challenges need to be successfully resolved. C26M/FeCrAl alloy systems can improve the safety and reliability of current Generation III reactors due to the potential benefits of a stable passivation layer from the Al, which can protect against corrosion, and promising mechanical performance at boiling- and light-water reactor temperatures. However, information is limited on how manufacturing techniques affect the mechanical performance of C26M in neutron-irradiated environments. In this research, C26M specimens were manufactured using three techniques and then irradiated at the Advanced Test Reactor at Idaho National Laboratory. This research aims to bridge this gap by investigating how the manufacturing techniques affects the mechanical performance of irradiated C26M at Generation III reactor relevant temperatures.

36 - MATERIALS SCIENCE↗
DOE OSTI2024

Tunable Metamaterials for Impact Mitigation

Traditional methods of shielding fragile goods and human tissues from impact energy rely on isotropic foam materials. The mechanical properties of these foams are inferior to an emerging class of metamaterials called plate lattices, which have predominantly been fabricated in simple 2.5-dimensional geometries using conventional methods that constrain the feasible design space. Here in this work, additive manufacturing is used to relax these constraints and realize plate lattice metamaterials with nontrivial, locally varying geometry. The limitations of traditional computer-aided design tools are circumvented and allow the simulation of complex buckling and collapse behaviors without a manual meshing step. By validating these simulations against experimental data from tests on fabricated samples, sweeping exploration of the plate lattice design space is enabled. Numerical and experimental tests demonstrate plate lattices absorb up to six times more impact energy at equivalent densities relative to foams and shield objects from impacts ten times more energetic while transmitting equivalent peak stresses. In contrast to previous investigations of plate lattice metamaterials, designs with nonuniform geometric prebuckling in the out-of-plane direction is explored and showed that these designs exhibit 10% higher energy absorption efficiency on average and 25% higher in the highest-performing design.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Supercritical Methanol Solvolysis and Catalysis for the Conversion of Delignified Woody Biomass into Light Alcohol Gasoline Bioblendstock

Supercritical methanol (SCM) solvolysis and catalysis has recently emerged as a promising pathway to produce gasoline-range light alcohols from woody biomass through staged depolymerization and hydro-deoxygenation (DHDO). Here, structure-property relationships of Cu"M"AlO x catalysts (M = Mg, Zr, and Ce) are examined for upgrading delignified hybrid poplar via SCM-DHDO. CuCeAlO x displays the highest activity, increasing the C 2 -C 7 alcohol production rate and selectivity by twofold in batch reactions, and >50% in semicontinuous reactions relative to the current state-of-the-art CuMgAlO x . The performance of CuCeAlOx is correlated with its high reducibility and acidity. Cu sintering and biogenic impurity poisoning are identified as possible deactivation mechanisms over 60 h of continuous testing. The gasoline-range SCM-DHDO products are comprised of primarily aliphatic alcohols that result in improved energy density and favorably reduced vapor pressure, relative to ethanol, with the tradeoff of nonsynergistic octane blending with conventional gasoline and lower oxidation stability. Overall, this work highlights the potential to produce suitable light oxygenates by SCM-DHDO processing for gasoline bioblendstock applications.

09 BIOMASS FUELS↗
DOE OSTI2023

Influence of native oxide film on corrosion behavior of additively manufactured stainless steel 316L

The influence of the native oxide film on passive film properties and localized corrosion of additively manufactured SS 316L was studied in 1 wt% HCl by XPS characterization, electrochemical polarization curves, and post-test morphology analysis by SEM. Increased Cr oxidation kinetics was observed in the as-polished sample with the native oxide film resulting in formation of an overall more protective and compact film compared to the cathodically-activated sample. Electrochemical analysis showed that corrosive attack varied between dislocation cell boundaries to cell interiors depending on the initial surface state and polarization conditions. In conclusion, a corrosion mechanism is proposed to explain this variation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Two promoters integrate multiple enhancer inputs to drive wild-type knirps expression in the Drosophila melanogaster embryo

Abstract Proper development depends on precise spatiotemporal gene expression patterns. Most developmental genes are regulated by multiple enhancers and often by multiple core promoters that generate similar transcripts. We hypothesize that multiple promoters may be required either because enhancers prefer a specific promoter or because multiple promoters serve as a redundancy mechanism. To test these hypotheses, we studied the expression of the knirps locus in the early Drosophila melanogaster embryo, which is mediated by multiple enhancers and core promoters. We found that one of these promoters resembles a typical “sharp” developmental promoter, while the other resembles a “broad” promoter usually associated with housekeeping genes. Using synthetic reporter constructs, we found that some, but not all, enhancers in the locus show a preference for one promoter, indicating that promoters provide both redundancy and specificity. By analyzing the reporter dynamics, we identified specific burst properties during the transcription process, namely burst size and frequency, that are most strongly tuned by the combination of promoter and enhancer. Using locus-sized reporters, we discovered that enhancers with no promoter preference in a synthetic setting have a preference in the locus context. Our results suggest that the presence of multiple promoters in a locus is due both to enhancer preference and a need for redundancy and that “broad” promoters with dispersed transcription start sites are common among developmental genes. They also imply that it can be difficult to extrapolate expression measurements from synthetic reporters to the locus context, where other variables shape a gene’s overall expression pattern.

Li, Lily (ORCID:0000000301986521)↗
DOE OSTI2025

VitriEdge: Repairable & Durable Vitrimer Coatings for Wind Turbine Blade Leading Edges

The primary goal of this Level 1b incubator project was to explore the use of vitrimer coatings for repair of leading-edge erosion on end-of-life wind turbine blade surfaces, beyond coating strength of adhesion which has previously been demonstrated in the Level 1a project. Uniform vitrimer coatings (thickness: 400 µm) were applied to two end-of-life wind turbine blades for flexural, fatigue, and laminate tensile testing where the addition of the coating did not produce any statistical variation in tensile properties with minor drops in flexural strength for some laminate formulations. However, a <2% variation in storage modulus was measured for laminate structures (i.e., blade samples with vitrimer coatings) across 100,000 flexural cycles and upon laminate tensile failure, the vitrimer coatings displayed no visible signs of delamination. In addition, three methods to heal vitrimer coating damage was displayed: oven heating, addition of hot water, and a forced convection heat gun. All three heating and healing mechanisms demonstrated significant healing with scratch depths decreasing between 79-91% at healing times ranging between 1-min and 10-minutes. Finally, a water jet machine was used to simulate rain erosion for both the blade surfaces and vitrimer-coated blade surfaces where the diameter and depth of the damage was recorded as a function of exposure time, water pressure, height of exposure, and angle of exposure. Of interest, while the vitrimer coating did not significantly lessen the damage experienced during rain erosion, the addition of vitrimer composite coatings(5 wt.% mica addition) did result in a crack-resistant, durable coating capable of self-healing behavior and in all cases the angle of rain exposure was the most critical parameter explored. It is crucial to continue exploring this space where vitrimer coatings are of interest for both their self-healing properties and potential use as reversible adhesives.

17 WIND ENERGY↗
DOE OSTI2022

Mechanical response and microstructure evolution from multiaxial stress relaxation in textured zircaloy nuclear cladding

Modern energy markets provide motivation for nuclear reactors to increase operational flexibility and load following capacity of existing reactor designs. The operational power changes result in fuel pellet expansion and contraction resulting in pellet-cladding mechanical interaction (PCMI) and high cladding stresses that are strongly related to stressed corrosion cracking (SCC) which can lead to fuel rod failure. This work aims to quantify the stress fields in cladding with a focus on multiaxial stress relaxation response from an imposed strain and the resulting microstructure changes in textured zircaloy claddings. Stress relaxation tests resulting in multiaxial stress fields are performed to measure the material response of Zircaloy-4 nuclear cladding. Multiple experiments using samples from the same piece of cladding are performed so samples with the same processing history may be removed at strategic points throughout mechanical testing for microstructure characterization. The microstructure evolution is analyzed with mechanical response to evaluate the static recovery impact on crystallographic texture and grain morphology. Experiments are performed at Idaho National Laboratory using an experimental device capable of applying internal pressure and independent axial load to commercial nuclear cladding at elevated temperatures with stress- or strain-controlled experimental capability. X-ray diffraction and electron backscatter diffraction are used for microstructure analysis. Rheological models are used to visualize the multiaxial stress-strain relationships and isolate elastic, plastic, and viscoplastic material properties for analysis.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Unveiling the Degradation Mechanism of High-Temperature Superconductor Bi 2 Sr 2 CaCu 2 O 8+δ in Water-Bearing Environments

We report the physical properties of copper oxide high-temperature superconductors have been studied extensively, such as its band structure, and doping effects of Bi 2 Sr 2 CaCu 2 O 8+δ (Bi-2212). However, some chemical-related properties of these superconductors are rarely reported, such as their stability in air. Here, we report experiments combined with ab initio calculations that address the effects of water in contact with Bi-2212. The evolution of Bi-2212 flake with exposure to water for different time intervals were tested and characterized by optical microscopy (OM), atomic force microscopy (AFM), Raman spectroscopy, transmission electron microscopy (TEM) and electrical measurements. The thickness of Bi-2212 flakes is gradually decreased in water, and some thin flakes can be completely etched away after a few days. The stability of Bi-2212 in other solvents is also evaluated, including alcohol, acetone, HCl and KOH. The morphology of Bi-2212 flakes is relatively stable in organic solvents. However, the flakes are etched relatively quick in HCl and KOH, especially in acidic environment. Our results imply that hydrogen ion is primarily responsible for the deterioration of their properties. Both TEM and calculation results demonstrate that the atoms in Bi-O plane is relatively stable when compared to the inner atoms in Sr-O, Ca-O and Cu-O planes. This work contributes towards understanding the chemical stability of Bi-2212 superconducting device in environmental medium, which is important for both fundamental studies and practical applications of copper oxide high-temperature superconductors.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

3D Time-Lapse Electrical Resistivity Imaging of Rock Damage Patterns and Gas Flow Paths Resulting from Two Underground Chemical Explosions

Abstract Rock damage from underground nuclear explosions (UNEs) has a strong influence on sub-surface gas movement and on seismic waveform characteristics, both of which are used to detect UNEs. Although advanced numerical simulation capabilities exist to predict rock damage patterns and corresponding detection signals, those predictions are dependent on (generally) unknown properties of the host rock. For example, the effects of in-situ mechanical heterogeneities on the explosively generated damage/fractures that provide gas flow pathways to the surface are not well understood, due largely to the difficulty in accessing and characterizing the near-source region. In this paper we demonstrate the emerging use of electrical resistivity tomography (ERT) for imaging rock damage and gas flow patterns resulting from two relatively small-scale underground chemical explosions. Pre-explosion ERT and crosshole seismic imaging revealed a natural fracture zone within the test bed. Post-explosion imaging revealed that the damage zone was non-symmetric and was focused primarily within the pre-existing fracture zone, located 10 m above the first explosion and 5 m above the second explosion. Time-lapse ERT imaging of heated air injected into the detonation borehole revealed the primary gas flow paths to be within the upper margin of the same primary damage zone. These results point to the utility of ERT imaging for understanding rock damage and gas flow patterns under experimental conditions, and to the importance of understanding the effects of geologic heterogeneity on UNE detection signals, particularly gas surface breakthrough times.

58 GEOSCIENCES↗
DOE OSTI2025

Electromagnetic moments of 215,217 Bi: Probing shell evolution beyond N = 126

The nuclear properties of bismuth isotopes (Z = 83) , with just one valence proton above the closed spherical shell at (Z = 82) , are expected to be governed by a single unpaired proton. However, already in semimagic 209 Bi (Z = 83, N = 126) , , the magnetic moment (μ) strongly deviates from the single-particle Schmidt value. A near linear decrease in μ with the increase of N after the N = 126 magic number was observed up to N = 130 . In order to test whether this trend is kept at N > 130 and to reveal the underlying mechanisms, an investigation of 215,217 Bi (N = 132, 134) has been undertaken. The magnetic dipole and electric quadrupole moments of the I π = 9/2 - nuclear ground states in these isotopes have been measured for the first time using the in-source resonance-ionization spectroscopy technique at ISOLDE (CERN). It has been shown that the linearly decreasing trend of μ( 209,211,213 Bi g ) is broken in 215,217 Bi with a nearly constant value of μ observed. Experimental data have been compared to calculations in the framework of the configuration-interaction shell model with the monopole-based universal V MU +LS interaction. The peculiarities in the behavior of μ(Bi, 9/2 - ) with increasing neutron number are explained as being due to the shell evolution, change of the neutron orbitals occupancies and strong configuration mixing beyond N = 130 . Also, the difference in the μ trends for bismuth (Z = 83) and astatine (Z = 85) isotopes with N > 126 are reproduced by the shell-model calculations. It is shown that monopole interaction plays noticeable role in the description of the peculiarities of the μ behaviour. Additionally, the extension of the application of the V MU interaction to the μ isotopic trends for heavy nuclei is important for further study of the capabilities of this promising version of the shell-model calculations.

Dipole magnetic moments↗
DOE OSTI2020

Evidence of Ba-substitution induced spin-canting in the magnetic Weyl semimetal EuCd 2 As 2

Recently EuCd 2 As 2 was predicted to be a magnetic Weyl semimetal with a lone pair of Weyl nodes generated by A-type antiferromagnetism and protected by a rotational symmetry. However, it was soon discovered that the actual magnetic structure broke the rotational symmetry and internal pressure was later suggested as a route to stabilize the desired magnetic state. In this work we test this prediction by synthesizing a series of Eu 1-x BaxCd 2 As 2 single crystals and studying their structural, magnetic, and transport properties via both experimental techniques and first-principles calculations. We find that small concentrations of Ba (~3%–10%) lead to a small out-of-plane canting of the Eu moment. However, for higher concentrations this effect is suppressed and a nearly in-plane model is recovered. Studying the transport properties we find that all compositions show evidence of an anomalous Hall effect dominated by the intrinsic mechanism as well as large negative magnetoresistances in the longitudinal channel. A nonmonotonic evolution of the transport properties is seen across the series which correlates to the proposed canting suggesting canting may enhance the topological effects. Careful density functional theory calculations using an all-electron approach revise prior predictions finding a purely ferromagnetic ground state with in-plane moments for both the EuCd 2 As 2 and Eu 0.5 Ba 0.5 Cd 2 As 2 compounds, corroborating our experimental findings. This work suggests that Ba substitution can tune the magnetic properties in unexpected ways which correlate to changes in measures of topological properties, encouraging future work to locate the ideal Ba concentration for Eu moment canting.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Lattice Design and Advanced Modeling to Guide the Design of High-Performance Lightweight Structural Materials

Lightweight structural materials are required to increase the mobility of fission batteries. The materials must feature a robust combination of mechanical properties to demonstrate structural resilience. The primary objective of this project is to produce lightweight structural materials whose strength-to-weight ratios exceed those of the current widely used structural materials such as 316L stainless steels (316L SS). To achieve this, advanced modeling and simulation tools were employed to design lattice structures with different lattice parameters and different lattice types. A process was successfully developed for transforming lattice-structures models into Multiphysics Object Oriented Simulation Environment (MOOSE) inputs. Finite element modeling (FEM) was used to simulate the uniaxial tensile testing of the lattice-structured parts to investigate the stress distribution at a given displacement. The preliminary results showed that the lattice-structured sample displayed a lower Young’s modulus in comparison with the solid material and that the unit cell size of the lattice had a minimal effect. The novelty here is to apply up-front modeling to determine the best structure for the application before actually producing the sample. The approach of using modeling as a guiding tool for preliminary material design can significantly save time and cost for material development.

36 MATERIALS SCIENCE↗
DOE OSTI2020

An experimental investigation of the effectiveness of Ar-CO 2 shielding gas mixture for the wire arc additive process

Wire arc additive manufacturing (AM) is the process by which a large, metallic structure is built layer-by-layer using a welding arc to melt a wire feedstock. A novel opportunity exists to alter the shielding gas composition to fabricate distinct geometrical features without altering the other AM parameters. In this paper, shielding gases with varied concentrations of Argon (Ar) and CO 2 was used to deposit three distinct geometric shapes (walls, infill, and overhang) using a wire-based additive manufacturing system utilizing the gas metal arc welding (GMAW) surface tension transfer (STT) process. Computer-aided design (CAD) models were sliced with a custom-built slicer, and the sliced algorithm was converted into optimal robotic toolpaths. A custom virtual instrument (VI) was built in LabVIEW to compare the temperature profiles on the surface during each deposition process. After each deposition, the geometric features were scanned, and the surface waviness value was evaluated. Tensile and Charpy impact coupons were extracted from the wall geometries in the longitudinal and transverse directions and tested. The results indicated that a higher CO 2 content produced higher melt pool temperatures to an extent, while lower contents of CO 2 resulted in a dimensionally accurate geometry. The data also indicated that the 2%/98% CO 2 /Ar blend produced scatter in tensile strength and the analysis of variance (ANOVA) shows significant difference. However, the intermediate range of CO 2 (5–10%) resulted in uniform tensile properties. Altogether, these results indicate that a 5%/95% CO 2 /Ar blend is the ideal shielding gas for lowering process temperatures and improving mechanical properties in wire arc additive manufacturing using the gas metal arc welding surface tension transfer process. Additionally, varying concentrations of Ar/CO 2 can be used within the same part in order to modify the local properties or process parameters such as strength, toughness, temperature, or dimensional features. This may improve overall manufacturing quality without sacrificing specific properties.

42 ENGINEERING↗
DOE OSTI2020

Fatigue behavior and modeling for additive manufactured 304L stainless steel: The effect of surface roughness

The fatigue strength of additively manufactured metallic parts in their as-built surface condition is mainly dominated by the surface roughness. Post-processing is often inevitable to reduce surface roughness effects even though post-processing diminishes the main advantage of additive manufacturing, which is net-shaped direct-to-service production. This work investigates the underlying mechanisms responsible for fatigue failure of additively manufactured 304L stainless steel parts in as-built and machined/polished surface conditions. Both strain- and force-controlled, fully reversed fatigue tests were conducted to gain a comprehensive understanding of surface roughness effects on fatigue behavior. The sensitivity to surface roughness is shown to be dependent on the control mode, with stress-based fatigue tests showing greater sensitivity than strain-based fatigue tests. Moreover, the fatigue life estimation for as-built specimens was performed based on surface roughness parameters as well as the fatigue properties of the specimens in machined/polished surface condition of the material without using any fatigue data of specimens in as-built surface condition. Accordingly, the effect of surface roughness on the fatigue behavior could be estimated reasonably well in both strain-life and stress-life approaches.

36 MATERIALS SCIENCE↗