Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “mass diffusivity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Probability density function approach for compressible turbulent reacting flows

The objective of the present work is to extend the probability density function (PDF) tubulence model to compressible reacting flows. The proability density function of the species mass fractions and enthalpy are obtained by solving a PDF evolution equation using a Monte Carlo scheme. The PDF solution procedure is coupled with a compression finite-volume flow solver which provides the velocity and pressure fields. A modeled PDF equation for compressible flows, capable of treating flows with shock waves and suitable to the present coupling scheme, is proposed and tested. Convergence of the combined finite-volume Monte Carlo solution procedure is discussed. Two super sonic diffusion flames are studied using the proposed PDF model and the results are compared with experimental data; marked improvements over solutions without PDF are observed.

Hsu, A. T.↗

Subaru SCExAO First-Light Direct Imaging of a Young Debris Disk around HD 36546

We present H-band scattered light imaging of a bright debris disk around the A0 star HD 36546 obtained from the Subaru Coronagraphic Extreme Adaptive Optics (SCExAO) system with data recorded by the HiCIAO camera using the vector vortex coronagraph. SCExAO traces the disk from r approximately 0 3 to r approximately 0".3 to r approximately 1" (34-114 au). The disk is oriented in a near east west direction (PA approximately 75deg), is inclined by I approximately 70deg-75deg, and is strongly forward-scattering(g greater than 0.5). It is an extended disk rather than a sharp ring; a second, diffuse dust population extends from the disks eastern side. While HD 36546 intrinsic properties are consistent with a wide age range (t approximately 1-250 Myr), its kinematics and analysis of coeval stars suggest a young age (310 Myr) and a possible connection to Taurus-Aurigas star formation history. SCExAOs planet-to-star contrast ratios are comparable to the first-light Gemini Planet Imager contrasts; for an age of 10 Myr, we rule out planets with masses comparable to HR 8799 b beyond a projected separation of 23 au. A massive icy planetesimal disk or an unseen super-Jovian planet at r greater than 20 au may explain the disks visibility. The HD 36546 debris disk may be the youngest debris disk yet imaged, is the first newly identified object from the now-operational SCExAO extreme AO system, is ideally suited for spectroscopic follow-up with SCExAO/CHARIS in 2017, and may be a key probe of icy planet formation and planet disk interactions.

Subaru Coronagraphic Extreme Adaptive Optics (SCEx↗

Observations of the structure of the diffuse X-ray emission from the Coma cluster

The Coma cluster has been scanned by an array of large X-ray proportional counters equipped with 10 min x 4 deg (FWHM) collimators. The results suggest the peak surface brightness is not coincident with one of the two giant elliptical galaxies, NGC 4889 and 4874, and show the X-ray emission to be more extended in the 0.5-1.5-keV band than in the 1.5-5-keV band. No evidence is found for concentrated X-ray sources, like those in M87 and NGC 1275. The X-ray surface brightness contours have an ellipticity which resembles that of the galaxy mass distribution, and evidence is found for clumpiness in the intracluster gas.

Johnson, M. W.↗

Radio continuum emission from T Tauri stars and associated structures

The current status of radio continuum observations of low mass, pre-main sequence stars (T Tauri stars) is discussed. The majority of T Tauri radio sources have been detected by the VLA telescope and a guide to both these and earlier observations is presented. Both nonthermal and thermal radio continuum emission has been detected from T Tauri stars. The likely emission processes and specific examples of their occurrence are outlined. The detected radio sources are often associated with the surroundings of the star, such as bipolar flows or diffuse extended optical nebulosity, rather than regions very close to the stellar surface. Only recently have radio continuum observations reached a sensitivity appropriate to the expected level of thermal free-free emission from the winds of ordinary T Tauri stars and it is possible that many more radio sources will now be found associated with these stars.

Brown, A.↗

Multi-Dimensional, Non-Pyrolyzing Ablation Test Problems

Non-pyrolyzingcarbonaceous materials represent a class of candidate material for hypersonic vehicle components providing both structural and thermal protection system capabilities. Two problems relevant to this technology are presented. The first considers the one-dimensional ablation of a carbon material subject to convective heating. The second considers two-dimensional conduction in a rectangular block subject to radiative heating. Surface thermochemistry for both problems includes finite-rate surface kinetics at low temperatures, diffusion limited ablation at intermediate temperatures, and vaporization at high temperatures. The first problem requires the solution of both the steady-state thermal profile with respect to the ablating surface and the transient thermal history for a one-dimensional ablating planar slab with temperature-dependent material properties. The slab front face is convectively heated and also reradiates to a room temperature environment. The back face is adiabatic. The steady-state temperature profile and steady-state mass loss rate should be predicted. Time-dependent front and back face temperature, surface recession and recession rate along with the final temperature profile should be predicted for the time-dependent solution. The second problem requires the solution for the transient temperature history for an ablating, two-dimensional rectangular solid with anisotropic, temperature-dependent thermal properties. The front face is radiatively heated, convectively cooled, and also reradiates to a room temperature environment. The back face and sidewalls are adiabatic. The solution should include the following 9 items: final surface recession profile, time-dependent temperature history of both the front face and back face at both the centerline and sidewall, as well as the time-dependent surface recession and recession rate on the front face at both the centerline and sidewall. The results of the problems from all submitters will be collected, summarized, and presented at a later conference.

Ablation↗

Numerical simulation of axisymmetric turbulent flow in combustors and diffusers

Numerical studies of turbulent flow in an axisymmetric 45-deg-expansion combustor and bifurcated diffuser are presented. The Navier-Stokes equations incorporating a k-epsilon model were solved in a nonorthogonal curvilinear coordinate system. A zonal-grid method, where the flow field was divided into several subsections, was developed. This approach permitted different computational schemes to be used in the various zones. In addition, grid generation was made a more simple task. Boundary overlap and interpolating techniques were used, and an adjustment of the flow variables was required to assure conservation of mass flux. Three finite-differencing methods (hybrid, quadratic upwind, and skew upwind) were used to represent the convection terms. Results were compared with existing experimental data. In general, good agreement between predicted and measured values was obtained.

Yung, Chain-Nan↗

Exploiting the Temperature/Concentration Dependence of Magnetic Susceptibility to Control Convection in Fundamental Studies of Solidification Phenomena

The objective of this new research project is to demonstrate by experiment, supplemented by mathematical modeling and physical property measurement, that the effects of buoyancy driven convection can be largely eliminated in ground-based experiments, and further reduced in flight, by applying a new technique. That technique exploits the dependence of magnetic susceptibility on composition or temperature. It is emphasized at the outset that the phenomenon to be exploited is fundamentally and practically different from the magnetic damping of convection in conducting liquids that has been the subject of much prior research. The concept suggesting this research is that all materials, even non-conductors, when placed in a magnetic field gradient, experience a force. Of particular interest here are paramagnetic and diamagnetic materials, classes which embrace the "model alloys", such as succinonitrile-acetone, that have been used by others investigating the fundamentals of solidification. Such alloys will exhibit a dependence of susceptibility on composition. The consequence is that, with a properly oriented field (gradient) a force will arise that can be made to be equal to, but opposite, the buoyancy force arising from concentration (or temperature) gradients. In this way convection can be stilled. The role of convection in determining the microstructure, and thereby properties, of materials is well known. Elimination of that convection has both scientific and technological consequences. Our knowledge of diffusive phenomena in solidification, phenomena normally hidden by the dominance of convection, is enhanced if we can study solidification of quiescent liquids. Furthermore, the microstructure, microchemistry and properties of materials (thereby practical value) are affected by the convection occurring during their solidification. Hitherto the method of choice for elimination of convection has been experimentation in microgravity. However, even in low Earth orbit, residual convection has effects. That residual convection arises from acceleration (drag on the spacecraft), displacement from the center of mass or transients in the gravitational field (g-jitter). There is therefore a need for both further reducing buoyancy driven flow in flight and allowing the simulation of microgravity during ground based experiments. Previous investigations, the research project description, theory behind the study and experimental methods as well as plots of magnetic fields and forces are presented.

Evans, J. W.↗

Mechanisms of Ionospheric Mass Escape

The dependence of ionospheric O+ escape flux on electromagnetic energy flux and electron precipitation into the ionosphere is derived for a hypothetical ambipolar pick-up process, powered the relative motion of plasmas and neutral upper atmosphere, and by electron precipitation, at heights where the ions are magnetized but influenced by photo-ionization, collisions with gas atoms, ambipolar and centrifugal acceleration. Ion pick-up by the convection electric field produces "ring-beam" or toroidal velocity distributions, as inferred from direct plasma measurements, from observations of the associated waves, and from the spectra of incoherent radar echoes. Ring-beams are unstable to plasma wave growth, resulting in rapid relaxation via transverse velocity diffusion, into transversely accelerated ion populations. Ion escape is substantially facilitated by the ambipolar potential, but is only weakly affected by centrifugal acceleration. If, as cited simulations suggest, ion ring beams relax into non-thermal velocity distributions with characteristic speed equal to the local ion-neutral flow speed, a generalized "Jeans escape" calculation shows that the escape flux of ionospheric O+ increases with Poynting flux and with precipitating electron density in rough agreement with observations.

Moore, T. E.↗

Mass spectrometric gas composition measurements associated with jet interaction tests in a high-enthalpy wind tunnel

Knowledge of test gas composition is important in wind-tunnel experiments measuring aerothermodynamic interactions. This paper describes measurements made by sampling the top of the test section during runs of the Langley 7-Inch High-Temperature Tunnel. The tests were conducted to determine the mixing of gas injected from a flat-plate model into a combustion-heated hypervelocity test stream and to monitor the CO2 produced in the combustion. The Mass Spectrometric (MS) measurements yield the mole fraction of N2 or He and CO2 reaching the sample inlets. The data obtained for several tunnel run conditions are related to the pressures measured in the tunnel test section and at the MS ionizer inlet. The apparent distributions of injected gas species and tunnel gas (CO2) are discussed relative to the sampling techniques. The measurements provided significant real-time data for the distribution of injected gases in the test section. The jet N2 diffused readily from the test stream, but the jet He was mostly entrained. The amounts of CO2 and Ar diffusing upward in the test section for several run conditions indicated the variability of the combustion-gas test-stream composition.

Lewis, B. W.↗

The quasi-periodic oscillations and very low frequency noise of Scorpius X-1 as transient chaos - A dripping handrail?

We present evidence that the quasi-periodic oscillations (QPO) and very low frequency noise (VLFN) characteristic of many accretion sources are different aspects of the same physical process. We analyzed a long, high time resolution EXOSAT observation of the low-mass X-ray binary (LMXB) Sco X-1. The X-ray luminosity varies stochastically on time scales from milliseconds to hours. The nature of this variability - as quantified with both power spectrum analysis and a new wavelet technique, the scalegram - agrees well with the dripping handrail accretion model, a simple dynamical system which exhibits transient chaos. In this model both the QPO and VLFN are produced by radiation from blobs with a wide size distribution, resulting from accretion and subsequent diffusion of hot gas, the density of which is limited by an unspecified instability to lie below a threshold.

Scargle, Jeffrey D.↗

Numerical modeling of diffusive physical vapor transport in cylindrical ampoules

Diffusion limited physical vapor transport in closed cylindrical ampoules of aspect ratio (length/radius) between 0.5 and 10 was studied numerically. The transport of a crystal forming component A through an inert component B, which undergoes zero net transport, was considered. A case in which the partial pressure of B is comparable to that of A, as well as systems with very low partial pressures of B (impurity cases) were treated. Concentrations and velocity distributions were obtained from the coupled transport equations for momentum, mass and components. It was found that the interdiffusion of components in viscous interaction with the container walls leads to (1) recirculation of component B, even in the absence of gravity; (2) concentration gradients normal to the main transport direction in the vapor space; and (3) non-uniform interfacial concentration gradients and, hence, non-uniform crystal growth rates.

Greenwell, D. W.↗

Dynamic evolution of low-energy ions in the terrestrial magnetosphere

Results of a statistical study of low-energy (0-50 eV) field-aligned ion pitch angle distributions for H(+), He(+), and O(+) observed by the Dynamics Explorer retarding ion mass spectrometer instrument are presented. Ion distributions are characterized as uni- and bi-directional field-aligned and bi-directional conic distributions. The spatial relationships of these distributions can be interpreted as dynamic evolution of low-energy ion flow in which injected unidirectional field-aligned streams originating in the nightside auroral zone evolve first into bi-directional flows under the influence of convection in the mirror magnetic field configuration. Characteristic convection times are evaluated with a pitch angle diffusion model in which field-aligned flows evolve into conical distributions through charge exchange loss of particles to the atmosphere during particle mirroring periods.

Giles, B. L.↗

Design, development, and test of a laser velocimeter for a small 8:1 pressure ratio centrifugal compressor

The instrument was designed as a diagnostic tool for the basic fluid dynamics of the inducer, impeller, and diffuser regions of this type compressor. The LV instrumentation was optimized to measure instantaneous velocities up to approximately 500 m/s, measured in absolute coordinates, within the rotating compressor impeller and in the two dimensional radial plane of the diffuser. Some measurements were made within the diffuser and the impeller inlet flows; however, attempts to make detailed measurements of the velocity field were not successful. Difficulties in maintaining high seed particle rates within the probe volume and the improper operation of the blade gating optics may explain the lack of success. Recommendations are made to further pursue these problems. At 100% speed the stage attained a total static pressure ratio of 7.5:1 at 75% total-static efficiency. Flow range from choke-to-surge was 6.8% of choking mass flow rate. Performance was lower than the design intent of 8:1 pressure ratio at 77% efficiency and 12% flow range. Detailed measurements of the stage components are presented which show the reasons for the stage performance deficiencies.

Dolan, F. X.↗

Global empirical model of the Venus thermosphere

Direct measurements of neutral CO2, O, CO, N2, He, and N densities from the Pioneer Venus Orbiter Neutral Mass Spectrometer are described in terms of a spherical harmonic representation (latitude and local time coordinates) of exospheric temperature and number densities at 150 km, using modified Bates temperature profiles. The exospheric temperatures are determined from the altitude variations of atomic oxygen. A global average temperature of 228 K is derived with a first harmonic variation of 5%. The altitude profiles are extended downward to 100 km by using empirical formulas to provide a transition through the turbopause region (simulating the effect of eddy diffusion and vertical flows) and matching entry probe density data. The model reflects the observed variations of temperature and density with the 10.7 cm radio flux index. For a given change in flux at the planet, the exospheric temperature on Venus changes by only 10% of the change seen in the terrestrial thermosphere.

Hedin, A. E.↗

Diffusion instability in a bimodal disc

A simplified model of radial diffusion in a planetary disk with a bimodal size distribution is presented. The large particle component excites the small particles' dispersion velocity via gravitational scattering. The resulting small particle viscous stress goes through a maximum near optical depth = sq root 3. Such a stress profile promotes the development of high and low optical depth zones. The resulting ringlet appearance is due primarily to the distribution of small particles, which produce most of the optical depth but may constitute only a minor portion of system mass.

Ward, W. R.↗

A simple biosphere model (SiB) for use within general circulation models

A simple realistic biosphere model for calculating the transfer of energy, mass and momentum between the atmosphere and the vegetated surface of the earth has been developed for use in atmospheric general circulation models. The vegetation in each terrestrial model grid is represented by an upper level, representing the perennial canopy of trees and shrubs, and a lower level, representing the annual cover of grasses and other heraceous species. The vegetation morphology and the physical and physiological properties of the vegetation layers determine such properties as: the reflection, transmission, absorption and emission of direct and diffuse radiation; the infiltration, drainage, and storage of the residual rainfall in the soil; and the control over the stomatal functioning. The model, with prescribed vegetation parameters and soil interactive soil moisture, can be used for prediction of the atmospheric circulation and precipitaion fields for short periods of up to a few weeks.

Sellers, P. J.↗

Discovery of high-ionization far-ultraviolet line emission from the interstellar medium

Diffuse, highly ionized line emission from the 1550 lines of C IV and the 1663 lines of O II was discovered on Space Shuttle mission 61-C. The emission-lines ratios are consistent with a single temperature in most directions, although there is some evidence that the emission results from gas with a nonequilibrium ionization balance and a distribution of temperatures. It is concluded that the observation of UV emission is consistent only with a galactic fountain model with a fountain having a mass flux of 6-25 solar mass/yr and a luminosity of (2.5-13) X 10 to the 40th ergs/s.

Martin, Christopher↗

Synthetic Jet Interaction With A Turbulent Boundary Layer Flow

Perhaps one of the more notable advances to have occurred in flow control technology in the last fifteen years is the application of surface-issuing jets for separation control on aerodynamic surfaces. The concept was introduced by Johnston and Night (1990) who proposed using circular jets, skewed and inclined to the wall, to generate streamwise vortices for the purpose of mitigating boundary layer separation. The skew and inclination angles have subsequently been shown to affect the strength and sign of the ensuing vortices. With a non-circular orifice, in addition to skew and inclination, the yaw angle of the major axis of the orifice can influence the flow control effectiveness of the jet. In particular, a study by Chang arid Collins (1997) revealed that a non-circular orifice, yawed relative to the freestream, can be used to control the size and strength of the vortices produced by the control jet. This early work used jets with only a steady injection of mass. Seifert et al. revealed that an unsteady blowing jet, could be as effective at separation control as a steady jet but with less mass flow. Seifert et al. showed that small amplitude blowing oscillations superimposed on a low momentum steady jet Was the most effective approach to delaying separation on a NACA 0015 airfoil at post-stall angles of attack. More recent work suggests that perhaps the most efficient jet control effect comes from a synthetic (oscillatory) jet where the time-averaged mass flux through the orifice is zero, but the net wall normal momentum is non-zero. The control effectiveness of synthetic jets has been demonstrated for several internal and external flow fields used synthetic jet control on a thick, blunt-nosed airfoil to delay stall well beyond the stall angles for the uncontrolled airfoil and with a dramatic increase in the lift-to-drag performance. Amitay et al. used an array of synthetic jets to mitigate flow separation in curved and diffusing ducts. While the control effectiveness of synthetic jet actuators in an application setting has been confirmed through a number of studies, the fluid dynamic mechanism by which control is effected is not well understood. Issues like yaw angle arid velocity ratio that have been studied for steady control jets have not been investigated for synthetic jets. Moreover, the role played by the inherently unsteady nature of a synthetic jet in the interaction with the controlled flow is not known. Some recent work by Rinehart and Glazer and Smith suggests that away from tile immediate vicinity of the jet orifice the flow field is steady in the mean, and that the interaction of a synthetic jet and a boundary layer creates a secondary flow in the boundary layer consisting primarily of streamwise vortices.

Smith, Douglas R.↗