Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “loss reduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58
All sourcesNASA NTRSDOE OSTI
NASA NTRS1952

Structural Vulnerability of the Boeing B-29 Aircraft Wing to Damage by Warhead Fragments

An elementary type of analysis has been used to determine the amount of wing tip that must be severed to produce irrevocable loss of control of a B-29 airplane. The remaining inboard structure of the Boeing B-29 wing has then been analyzed and curves are presented for the estimated reduction in structural strength due to four general types of damage produced by rod-type warhead fragments. The curves indicate the extent of structural damage required to produce a kill of the aircraft within 10 seconds.

Kordes, Eldon E.↗
NASA NTRS2010

Employing ISRU Models to Improve Hardware Design

An analytical model for hydrogen reduction of regolith was used to investigate the effects of several key variables on the energy and mass performance of reactors for a lunar in-situ resource utilization oxygen production plant. Reactor geometry, reaction time, number of reactors, heat recuperation, heat loss, and operating pressure were all studied to guide hardware designers who are developing future prototype reactors. The effects of heat recuperation where the incoming regolith is pre-heated by the hot spent regolith before transfer was also investigated for the first time. In general, longer reaction times per batch provide a lower overall energy, but also result in larger and heavier reactors. Three reactors with long heat-up times results in similar energy requirements as a two-reactor system with all other parameters the same. Three reactors with heat recuperation results in energy reductions of 20 to 40 percent compared to a three-reactor system with no heat recuperation. Increasing operating pressure can provide similar energy reductions as heat recuperation for the same reaction times.

Linne, Diane L.↗
DOE OSTI2022

In silico evaluation of plant nitrification suppression effects on agroecosystem nitrogen loss

Abstract Nitrification regulates the potential for nitrogen (N) loss from ecosystems because it converts ammonium to nitrate, which is susceptible to leaching and gaseous emissions. Crops can suppress the microbes that perform nitrification by exuding nitrification‐inhibiting compounds from their roots and taking up available ammonium. However, the effect of nitrification suppression on agroecosystem N losses remains poorly characterized, and a lack of temporal synchrony between nitrification, N losses, and nitrification suppression by plants could limit the effect of nitrification suppression. We used the DayCent‐CABBI model to evaluate the effectiveness of the suppression of nitrification by sorghum to reduce N 2 O emissions and nitrate leaching in an energy sorghum/soybean rotation at the Energy Farm in Urbana‐Champaign, IL. We simulated nitrification suppression at the measured levels (MeasNS) and at the maximum measured level applied to the entire growing season (MaxNS), and we also explored ways to better utilize nitrification suppression by altering the timing of urea–ammonium–nitrate fertilizer applications. Model experiments showed that most nitrification occurred immediately after fertilizer was applied, whereas nitrification suppression began to ramp up more than a month after planting. On an annual basis, MeasNS experiments showed a 1%–2% reduction in annual N 2 O emissions relative to no nitrification suppression (NoNS), and MaxNS experiments showed a 4%–9% reduction in annual N 2 O emissions relative to NoNS. Both nitrification suppression levels showed <1% reduction in nitrate leaching. Altering the timing of fertilizer applications to better synchronize nitrification suppression with high soil ammonium levels had mixed effects on annual N 2 O emissions and nitrate leaching and sometimes resulted in increased N losses. The timing of simulated N 2 O emissions shifted with the timing of fertilization, and N 2 O emissions from denitrification increased when N 2 O emissions from nitrification decreased. Increasing N retention during the non‐growing season may be more effective than growing‐season nitrification suppression for reducing annual N losses in the rainfed Midwest.

60 APPLIED LIFE SCIENCES↗
NASA NTRS1978

Modeling aerosol losses and clothing effects in fires

The described modification of a physiochemical fire model predicts physical effects in clothed humans exposed to elevated temperatures as well as gas and aerosol concentrations in the atmosphere of an aerospace vehicle. The modifications involve the reduction in aerosol concentrations caused by settling and some improvements in dealing with mass and heat transfer effects. Predicted skin temperatures are found to be within 2 C of experimental values for the cases studied, and model predictions of total body enthalpy seem to correlate with symptomology observed experimentally.

Cagliostro, D. E.↗
DOE OSTI2025

Mechanical-Bond-Enabled Highly Efficient Charge Separation in a Light-Harvesting Hetero[2]Catenane

Photodriven charge separation is a key process for converting solar energy into chemical energy. However, it remains a challenge to develop artificial light-harvesting materials that can simultaneously achieve ultrafast charge separation and a long-lived charge-separated state with low energy loss. In contrast to conventional strategies based on covalent or noncovalent interactions, we employed a mechanical bond to forcibly assemble two strongly electron-deficient cationic chromophores (TTzBo x4+ and PDI-C 2+ ), which have very similar reduction potentials and exhibit limited noncovalent interactions, into a hetero[2]catenane (TTzPCat 6+ ). This design provides efficient π electronic couplings, enabling ultrafast charge separation (<2.3 ps) even with a low driving force (|ΔG CS | ≈ 160 meV). Furthermore, the adaptive molecular conformation of TTzPCat 6+ , in combination with the Marcus inverted region effect, successfully prolongs the charge-separated state lifetime (k CS /k CR > 1000), surpassing the conventional trade-off between driving force and charge separation efficiency in heterogeneous donor–acceptor systems. The photocatalytic system based on TTzPCat 6+ exhibits an over 2-fold enhancement in selective oxidation of aryl sulfides under mild conditions, demonstrating the potential of mechanical bonding for preparing photocatalytic materials. This investigation not only highlights a strategy for achieving highly efficient charge separation with low energy loss but also offers fresh insights into developing efficient solar energy conversion systems.

Charge transfer↗
DOE OSTI2022

Enhanced Electrolyte Transport and Kinetics Mitigate Graphite Exfoliation and Li Plating in Fast–Charging Li–Ion Batteries

Despite significant progress in energy retention, lithium-ion batteries (LIBs) face untenable reductions in cycle life under extreme fast-charging (XFC) conditions, which primarily originate from a variety of kinetic limitations between the graphite anode and the electrolyte. Through quantitative Li + loss accounting and comprehensive materials analyses, it is directly observed that the operation of LIB pouch cells at 4 C||C/3 (charging||discharging) results in Li plating, disadvantageous solid-electrolyte-interphase formation, and solvent co-intercalation leading to interstitial decomposition within graphite layers. It is found that these failure modes originate from the insufficient properties of conventional electrolytes, where employing a designed ester-based electrolyte improved the capacity retention of these cells from 55.9% to 88.2% after 500 cycles when operated at the aforementioned conditions. These metrics are the result of effective mitigation of the aforementioned failure modes due to superior Li + transport and desolvation characteristics demonstrated through both experimental and computational characterization. Finally, this work reveals the vital nature of electrolyte design to XFC performance.

25 ENERGY STORAGE↗
DOE OSTI2023

A High Energy–Density, Cobalt–Free, Low–Nickel LiNi 0.7 Mn 0.25 Al 0.05 O 2 Cathode with a High–Voltage Electrolyte for Lithium–Metal Batteries

Cobalt-free cathode materials have garnered increased attention for applications in next-generation batteries for electric vehicles, as cobalt is considered to have at a high supply chain risk. Here, the use of a localized saturated electrolyte (LSE) to enable stable cycling of a cobalt-free, low-nickel layered-oxide cathode LiNi 0.7 Mn 0.25 Al 0.05 O 2 (NMA-70) to higher voltages (4.6 V) in a lithium-metal battery is demonstrated. Compared to the baseline LP57 electrolyte, the LSE extends the cycle life from ≈100 cycles to ≈400 cycles before reaching 80% capacity retention. Visual indicators of cell degradation, such as product deposition, are observed on electrodes cycled in LP57. It is shown that cycling NMA-70 in LSE reduces the overall active material loss and overpotential growth during extended cycling. This is attributed to the formation of a beneficial fluorinated interphase layer, a lower degree of rock-salt phase formation, and a reduction in the gas evolution from the cathode surface. The decrease in gas evolution from the cathode cycled in LSE reflects a lower degree of electrolyte reactivity and an overall improvement in the safety characteristics of the cell. Furthermore, this study highlights the importance of a stable electrolyte to enable the high-voltage cycling of alternative, lower nickel, and cobalt-free cathodes.

25 ENERGY STORAGE↗
DOE OSTI2023

FACsPb Triple Halide Perovskite Solar Cells with Thermal Operation over 200 °C

Formamidinium cesium (FACs) perovskites solar cells have been shown to be among the most stable metal halide perovskites. In this report high-temperature data are presented which systematically and statistically demonstrate the high thermal operation of this system to temperatures in excess of 200 degrees C. Device measurements between 250 K and 490 K show that while some loss of performance is evident at higher temperature, this is driven by reversible halide segregation with no evidence of a structural phase transition over the measurement range probed. Moreover, upon reduction of the temperature back to ambient the power conversion efficiency is retained.

14 SOLAR ENERGY↗
DOE OSTI2023

Crystal structure of MbnF: an NADPH-dependent flavin monooxygenase from Methylocystis strain SB2

Methanobactins (MBs) are ribosomally produced and post-translationally modified peptides (RiPPs) that are used by methanotrophs for copper acquisition. The signature post-translational modification of MBs is the formation of two heterocyclic groups, either an oxazolone, pyrazinedione or imidazolone group, with an associated thioamide from an X -Cys dipeptide. The precursor peptide (MbnA) for MB formation is found in a gene cluster of MB-associated genes. The exact biosynthetic pathway of MB formation is not yet fully understood, and there are still uncharacterized proteins in some MB gene clusters, particularly those that produce pyrazinedione or imidazolone rings. One such protein is MbnF, which is proposed to be a flavin monooxygenase (FMO) based on homology. To help to elucidate its possible function, MbnF from Methylocystis sp. strain SB2 was recombinantly produced in Escherichia coli and its X-ray crystal structure was resolved to 2.6 Å resolution. Based on its structural features, MbnF appears to be a type A FMO, most of which catalyze hydroxylation reactions. Preliminary functional characterization shows that MbnF preferentially oxidizes NADPH over NADH, supporting NAD(P)H-mediated flavin reduction, which is the initial step in the reaction cycle of several type A FMO enzymes. It is also shown that MbnF binds the precursor peptide for MB, with subsequent loss of the leader peptide sequence as well as the last three C-terminal amino acids, suggesting that MbnF might be needed for this process to occur. Finally, molecular-dynamics simulations revealed a channel in MbnF that is capable of accommodating the core MbnA fragment minus the three C-terminal amino acids.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Detection of a Cobalt-Containing Interphase at the Li 6 PS 5 Cl-NMC111 Interface by In Situ μ XANES and EIS

Sulfide electrolyte all-solid-state lithium batteries (ASLBs) with uncoated Li-Ni x Mn y Co 1–x–y O 2 (NMC) cathodes suffer from a large capacity loss during initial cycling and an increase in cell impedance. Decomposition reactions are known to occur at the Li 6 PS 5 Cl-NMC111 interface due to incompatibility between the two materials. If a stabilizing coating is applied to the NMC, it delivers full capacity during initial charge. However, the loss in capacity during discharge still occurs. The interface was studied by μ XANES and through EIS analysis. A chemically-formed interphase was detected by μ XANES, evident from reduction of Co at an uncoated NMC particle surface. This interphase was produced by decomposition at rest. To study the effect of the interphase on electrochemically active surface area, piecewise in situ EIS was performed and the data was modeled using a transmission line model (TLM). The charge transfer resistance R CT was used to estimate the volume specific active surface area (a act ). The median value for a act was 296 cm –1 , a factor of 7.5 lower than the theoretical value of 2216 cm –1 . This provided evidence of a lower electrochemically active surface area in the ASLB.

36 MATERIALS SCIENCE↗
DOE OSTI2022

ERLs and Sustainability

In any new accelerator proposal, sustainability issues will be heavily scrutinized, be that in electricity and water use, the overall efficiency of the facility, including reusing the heat for other purposes (space heating, biogas production, etc.) or energy recycling. These aspects are important for all new facilities, but ERLs bring a new dimension. Directly returning the energy of an unused beam into RF that can be used for acceleration with practically no losses is a unique feature of ERLs. While not all of the energy can be recovered, the overall efficiency of the process is extremely high. This advantage starts with a reduction in the RF power needed for acceleration, which translates into smaller RF sources and their associated power transformers (reducing the resources needed for their production), and less electric power and water cooling required (reduced operating costs as well as a reduced carbon footprint). Given the inherent advantages of ERLs, it is to be expected that their sustainability profile will eclipse other colliders with similar physics potential.

Hutton, Andrew↗
NASA NTRS1983

Causes and consequences of reduced blood volume in space flight - A multi-discipline modeling study

A group of mathematical models of various physiological systems have been developed and applied to studying problems associated with adaptation to weightlessness. One biomedical issue which could be addressed by at least three of these models from varying perspectives was the reduction in blood volume that universally occurs in astronauts. Accordingly, models of fluid-electrolyte, erythropoiesis, and cardiovascular regulation were employed to study the causes and consequences of blood volume loss during space flight. This analysis confirms the notion that alterations of blood volume are central to an understanding of adaptation to prolonged space flight. More importantly, the modeling studies resulted in specific hypotheses accounting for plasma volume and red cell mass losses and testable predictions concerning the behavior of the circulatory system.

Leonard, J. I.↗
NASA NTRS1989

Observations of, and sources of the spatial and temporal variability of ozone in the middle atmosphere on climatological time scales (OZMAP) and equatorial dynamics: Seasonal variations of ozone trends

The long term trends (least square linear regression with time) of ozone content at seven European, seven North American, three Japanese and two tropical stations during 21 years (1964 to 1984) are analyzed. In all regions negative trends are observed during the 1970s, but are partly compensated by limited periods of positive trends during the late 1960s and late 1970s. Solely the North American ozone data show negative trends in all 10 year periods. When the long term ozone trends are evaluated for each month of the year separately, a seasonal variation is revealed, which in Europe and North America has largest negative trends in late winter and spring. While in Europe the negative trends in winter/spring are partly compensated by positive trends in summer, in North America the summer values reach only zero, retaining the significant negative trend in annual mean values. In contrast to the antarctic ozone hole, the spring reduction of ozone in Europe and in North America is associated with stratospheric temperatures increasing in the analyzed period and therefore is consistent with the major natural ozone production and loss processes.

Entzian, G.↗
NASA NTRS1994

Effects of plasma hydrogenation on trapping properties of dislocations in heteroepitaxial InP/GaAs

In previous work, we have demonstrated the effectiveness of a post-growth hydrogen plasma treatment for passivating the electrical activity of dislocations in metalorganic chemical vapor deposition (MOCVD) grown InP on GaAs substrates by a more than two order of magnitude reduction in deep level concentration and an improvement in reverse bias leakage current by a factor of approximately 20. These results make plasma hydrogenation an extremely promising technique for achieving high efficiency large area and light weight heteroepitaxial InP solar cells for space applications. In this work we investigate the carrier trapping process by dislocations in heteroepitaxial InP/GaAs and the role of hydrogen passivation on this process. It is shown that the charge trapping kinetics of dislocations after hydrogen passivation are significantly altered, approaching point defect-like behavior consistent with a transformation from a high concentration of dislocation-related defect bands within the InP bandgap to a low concentration of individual dislocation related deep levels, before and after passivation. It is further shown that the 'apparent' activation energies of dislocation related deep levels, before and after passivation, reduce by approximately 70 meV as DLTS fill pulse times are increased from 1 microsecond to 1 millisecond. A model is proposed which explains these effects based on a reduction of Coulombic interaction between individual core sites along the dislocation cores by hydrogen incorporation. Knowledge of the trapping properties in these specific structures is important to develop optimum, low loss heteroepitaxial InP cells.

Ringel, S. A.↗
NASA NTRS1994

Effects of Plasma Hydrogenation on Trapping Properties of Dislocations in Heteroepitaxial InP/GaAs

In previous work, we have demonstrated the effectiveness of a post-growth hydrogen plasma treatment for passivating the electrical activity of dislocations in metalorganic chemical vapor deposition (MOCVD) grown InP on GaAs substrates by a more than two order of magnitude reduction in deep level concentration and an improvement in reverse bias leakage current by a factor of approx. 20. These results make plasma hydrogenation an extremely promising technique for achieving high efficiency large area and light weight heteroepitaxial InP solar cells for space applications. In this work we investigate the carrier trapping process by dislocations in heteroepitaxial InP/GaAs and the role of hydrogen passivation on this process. It is shown that the charge trapping kinetics of dislocations after hydrogen passivation are significantly altered, approaching point defect-like behavior consistent with a transformation from a high concentration of dislocation-related defect bands within the InP bandgap to a low concentration of individual deep levels after hydrogen passivation. It is further shown that the "apparent" activation energies of dislocation related deep levels, before and after passivation, reduce by approx. 70 meV as DLTS fill pulse times are increased from 1 usec. to 1 msec. A model is proposed which explains these effects based on a reduction of Coulombic interaction between individual core sites along the dislocation cores by hydrogen incorporation. Knowledge of the trapping properties in these specific structures is important to develop optimum, low loss heteroepitaxial InP cells.

Ringel, S. A.↗
NASA NTRS1986

Statolith formation in Cnidaria: effects of cadmium on Aurelia statoliths

Statolith formation in Cnidaria was reviewed with an emphasis on Aurelia statoliths. The review provides information on the chemical composition, mechanisms of initiation of mineralization, and effects of environmental factors on Cnidarian statolith formation. Environmental factors discussed included modified sea water ingredients, X-irradiation, clinostat rotation, and petroleum oil ingredients. A detailed account of the effects of cadmium on mineralization and demineralization of Aurelia statoliths is given. Cadmium at dosages of 2 to 4 micromoles significantly reduces statolith numbers in developing ephyrae. At a dosage of 3 micromoles, cadmium accelerates statolith loss in unfed ephyrae studied at 4 and 8 days following ephyrae release from strobilae. Cadmium, therefore, is shown to reduce statolith numbers in developing ephyrae and to cause greater reduction of statolith numbers in unfed ephyrae after 4 and 8 days than occurred in controls. Supplementation of Cd(2+)-containing artificial sea water (ASW) with calcium (3X and 5X ASW calcium content) results in higher numbers of statoliths at day 4 as compared with cadmium-treated ephyrae. At 8 days only the 5X calcium supplemented ASW is effective in enhancing statolith numbers in Cd(2+)-treated ephyrae. These results suggest that cadmium competes in some manner with calcium at the mineralizing sites of Aurelia.

NASA Discipline Number 40-10↗
NASA NTRS2015

Interactions of Mean Climate Change and Climate Variability on Food Security Extremes

Recognizing that climate change will affect agricultural systems both through mean changes and through shifts in climate variability and associated extreme events, we present preliminary analyses of climate impacts from a network of 1137 crop modeling sites contributed to the AgMIP Coordinated Climate-Crop Modeling Project (C3MP). At each site sensitivity tests were run according to a common protocol, which enables the fitting of crop model emulators across a range of carbon dioxide, temperature, and water (CTW) changes. C3MP can elucidate several aspects of these changes and quantify crop responses across a wide diversity of farming systems. Here we test the hypothesis that climate change and variability interact in three main ways. First, mean climate changes can affect yields across an entire time period. Second, extreme events (when they do occur) may be more sensitive to climate changes than a year with normal climate. Third, mean climate changes can alter the likelihood of climate extremes, leading to more frequent seasons with anomalies outside of the expected conditions for which management was designed. In this way, shifts in climate variability can result in an increase or reduction of mean yield, as extreme climate events tend to have lower yield than years with normal climate.C3MP maize simulations across 126 farms reveal a clear indication and quantification (as response functions) of mean climate impacts on mean yield and clearly show that mean climate changes will directly affect the variability of yield. Yield reductions from increased climate variability are not as clear as crop models tend to be less sensitive to dangers on the cool and wet extremes of climate variability, likely underestimating losses from water-logging, floods, and frosts.

Variability↗
NASA NTRS2020

Detection of Dynamical Instability in Titan's Thermospheric Jet

Similar to Earth, Saturn’s largest moon, Titan, possesses a system of high-altitude zonal winds (or jets) that encircle the globe. Using the Atacama Large Millimeter/submillimeter Array (ALMA) in August 2016, Lellouch et al. (2019) discovered an equatorial jet at much higher altitudes than previously known, with a surprisingly fast speed of up to∼340 m s−1, but the origin of such high velocities is not yet understood. We obtained spectrally and spatially resolved ALMA observations in May 2017 to map Titan’s 3D global wind field and compare our results with a reanalysis of the August 2016 data. Doppler wind velocity maps were derived in the altitude range∼300–1000 km (from the upper stratosphere to the thermosphere). At the highest, thermospheric altitudes, a 47% reduction in the equatorial zonal wind speed was measured over the 9-month period (corresponding toLs= 82◦–90◦on Titan). This is interpreted as due to a dramatic slowing and loss of confinement (broadening) of the recently-discovered thermospheric equatorial jet, as a result of dynamical instability. These unexpectedly-rapid changes in the upper-atmospheric dynamics are consistent with strong variability of the jet’s primary driving mechanism.

M A Cordiner↗