Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “high strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Perspectives on Quenching and Tempering 4340 Steel

Steels are ubiquitous due to their affordability and the landscape of useful properties that can be generated for engineering applications. But to further expand the performance envelope, one must be able to understand and control microstructure development by alloying and processing. In this paper we use multiscale, advanced characterization to better understand the structural and chemical evolution of AISI 4340 steel after quenching and tempering (Q&T), including the role of quench rate and short-time, isothermal tempering below 573 K (300 °C), with an emphasis on carbide formation. We compare the microstructure and/or property changes produced by conventional tempering to those produced by higher temperature, short-time “rapid” tempering. We underscore that no single characterization technique can fully capture the subtle microstructure changes like carbon redistribution, transition carbide and/or cementite formation, and retained austenite decomposition that occur during Q&T. Only the use of multiple techniques begins to unravel these complexities. After controlled fast or slow quenching, η transition carbides clearly exist in the microstructure, likely associated with autotempering of this high martensite start temperature (Ms) steel. Isothermal tempering below 598 K (325 °C) results in the relief of carbon supersaturation in the martensite, primarily by the formation of η transition carbides that exhibit a range of carbon levels, seemingly without substitutional element partitioning between the carbide and matrix phases. Hägg transition carbide is present between 300 °C and 325 °C. After conventional tempering at or above 598 K (325 °C) for 2 h, cementite is predominant, but small amounts of cementite are also present in other conditions, even after quenching. Previous work has indicated that silicon (Si) and substitutional elements partition between the cementite, which initially forms under paraequilibrium conditions, and the matrix. Phosphorous (P) may also be preferentially located at cementite/matrix interfaces after high temperature tempering. Slower quench rates result in greater amounts of retained austenite compared to those after fast quenching, which we attribute to increased austenite stability resulting from “autopartitioning”. Rapid, high temperature tempering is also found to diminish tempered martensite embrittlement (TME) believed to be associated with the extent of austenite decomposition, resulting in mechanical properties not attainable by conventional tempering, which may have important implications with respect to industrial heat treatment processes like induction tempering. Controlling the amount and stability of retained austenite is not only relevant to the properties of Q&T steels, but also next-generation advanced high strength steels (AHSS) with austenite/martensite mixtures.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Manipulating Retained Austenite Fraction and Stability With Controlled Chemical Heterogeneities in Q&P Steels

Advanced high-strength steels go through complex heat treatment processes with the goal of retaining austenite to enhance the mechanical properties. Martensite start temperature predictions are generally based on bulk composition when designing heat treatments, so compositional heterogeneities are not considered. Here, the effects of compositional heterogeneities on retained austenite fractions in a quenching and partitioning steel are investigated. In conclusion, the results show that Mn banding from solidification can be used to change retained austenite fractions.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Stimulating β -Series Precipitation in Mg–Nd Alloys Via Microalloying: A Comparison of Electron Microscopy and Small-Angle Scattering Techniques

The Mg–Nd alloy system is of particular interest in the development of high-strength, lightweight structural alloys due to the formation of strengthening metastable Mg–Nd β-series precipitates during heat treatment. The strengthening is primarily provided by a combination of the β''' and β 1 precipitation. It is therefore important to understand how the precipitation behavior can be enhanced by other common alloying elements. In this work, the effects of 0.2 wt pct Zn and Ca on β-series precipitation were studied. Small-angle/ultra-small-angle X-ray scattering (SAXS/USAXS) techniques in combination with scanning transmission electron microscopy (STEM) were used to study the evolution of precipitation microstructure. Here, it is found that the Zn additions refine the precipitates, leading to an increase in hardness with aging at 200 °C. On the other hand, the Ca additions result in an acceleration in the formation of larger β 1 precipitates and chains which provides less strengthening. The β 1 chains are surrounded by precipitate-free zones (PFZs) that further contribute to the decreases in hardness observed in the over-aged condition. This paper demonstrated that SAXS/USAXS provides a powerful tool for an in situ study of the early stages of precipitation in the Mg–Nd-based alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Microstructural, Oxidation, and Mechanical Behavior of NbTi-Based Refractory Alloys with 5 to 10 Pct Co, Cr, and Ni Additions

NbTi-based refractory alloys with additions of Co, Cr, and Ni represent an interesting medium-entropy alloy system with potential for protective oxide film formation, high strength, and ductility. This study investigates the microstructural evolution, oxidation behavior, and mechanical properties of NbTi-based alloys containing 5 to 10 at. pct Co, Cr, and Ni. CALPHAD predictions suggest that this composition range can be heat treated to obtain a predominantly body-centered cubic matrix phase. Mechanical properties, including microhardness, yield strength, maximum strength, and specific strength are evaluated through isothermal compression tests conducted between room temperature and 800 °C. The oxidation kinetics of these alloys are assessed through discontinuous oxidation tests. Parabolic oxidation kinetics were observed for NbTi–10Ni and NbTi–5Co, while linear oxidation kinetics were found for NbTi–10Cr and NbTi–10(CoCrNi). Microstructures and oxide layers are characterized using X-ray diffraction, electron backscatter diffraction, energy-dispersive X-ray spectroscopy, and scanning electron microscopy. All alloys exhibit significant mechanical softening between room temperature and 800 °C, with elastic-perfectly plastic flow observed at 800 °C. The addition of 10 pct Cr to NbTi resulted in two BCC phases up to 1050 °C, conflicting with CALPHAD predictions of a single-phase solid solution at this temperature, and resulting in higher flow stress at 800 °C. NbTi–10(CoCrNi) exhibited the lowest flow stress at 800 °C despite having more ‘cocktail effect’ potential and insufficient molar fractions of Co, Cr, or Ni to form a desirable protective oxide film.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Quality Control of Additively Manufactured Metallic Structures with Machine Learning of Thermography Images

Additive manufacturing (AM) of high-strength metals is currently based on the laser powder bed fusion (LPBF) process, which can introduce internal material flaws, such as pores and anisotropy. Quality control (QC) requires nondestructive evaluation of actual AM structures. Flash thermography is a potentially promising QC technique because it is scalable to arbitrary structure size. However, the detection sensitivity of this method is limited by noise. We investigate separation of signal from noise in thermography images using several machine learning (ML) methods, including new spatial–temporal blind source separation and spatial–temporal sparse dictionary learning methods. Performance of the ML methods is benchmarked using thermography data obtained from imaging stainless steel 316L and Inconel 718 specimens produced by the LPBF method with imprinted calibrated porosity defects. The ML methods are ranked by F-score and execution runtime. Finally, the ML methods with higher accuracy require a longer runtime. However, this runtime is sufficiently short to perform QC within a realistic time frame.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Insights into the Transformation-Induced Plasticity (TRIP) Effect in Ti-Free Grade 300 Maraging Steel Manufactured by Laser Powder Bed Fusion (LPBF)

The near-net fabrication capabilities of laser powder-bed fusion (LPBF) offer the potential to manufacture tools with complex cooling channels that can improve the production efficiency of the tools with reduced greenhouse gas emissions. High strength, toughness, and wear resistance are some of the key properties required by the tooling industries to qualify tools. While strength can be increased through appropriate heat treatments, the increase in strength comes with an associated ductility loss. Here, we show that the non-equilibrium conditions inherent to LPBF can suppress the transformation-induced plasticity effect to room temperature in a Ti-free version of grade 300 maraging steel (G300MS), which is commonly not observed at room temperature in G300MS manufactured using conventional methods. The presence of retained austenite along with Ni-rich regions was found to increase the kinetics for austenite reversion during aging, thereby enabling the transformation of austenite into ε martensite during tensile deformation at room temperature, in turn increasing the strength with minimal ductility loss.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Cladding and Butt-Joining Dissimilar Aluminum Alloys Simultaneously via Shear Assisted Processing and Extrusion

Shear assisted processing and extrusion has been used to fabricate multi-metallic tubing that incorporates regions with clad and butt-joined structures. In this work, aluminum alloys 6061, 7075, and 1100 are combined to create a monolithic extruded tubing with weldable ends (6061), a high strength center (7075), and a corrosion-resistant cladding (1100). Optical microscopy shows a gradual, defect-free, transition between alloys at the butt-joint interfaces and a sharp transition between alloys at the clad interface. Tensile testing proved the mechanical coherency of the joint, with failure occurring outside the tri-metallic structure. In conclusion, smoothed particle hydrodynamic simulations identified a spiral pattern of the cladding alloy that leads to inconsistent cladding thickness, and identified a simplified 2-alloy combination of aluminum alloys 6082 and 2014 that accomplished the design objectives of the tri-metallic structure.

Coatings↗
DOE OSTI2026

MoNbTi-based Refractory Multi-principal Element Alloy System: A Review of the Thermodynamic Phase Predictions, Formed Microstructures, and Mechanical Properties as a Function of the Fabrication Methods (AM versus SPS versus VAM)

Abstract Multi-principal element alloys, particularly of refractory compositions, are an increasingly popular candidate for extreme-environment applications, including for next-generation nuclear reactors and in other industries, such as biomedical and aerospace, due to their high strength. The ability to achieve solid-solution microstructures provides these alloys with improved mechanical properties; however, these microstructures are heavily composition- and processing-dependent. In this review, the multi-principal element alloy MoNbTi-based system (with Zr, V, and Cr additions) was selected to compare the effects of elemental composition and processing route on the resulting microstructures and mechanical properties. The review provides insight into identifying the optimal alloy composition and processing route for a balance of desired microstructure and mechanical properties.

Krogh, Kara↗
DOE OSTI2025

An Integrated High-Speed Microstructural Characterization Method Using Simultaneous XRD, Stereo-DIC, and PCI

High-speed characterization of the deformation mechanisms in polycrystalline metals requires the quantification of full strain fields and local microstructural evolutions simultaneously. In this paper, we present a novel experimental method to integrate phase-contrast imaging (PCI), stereographic digital image correlation (stereo-DIC), and full-ring X-ray diffraction (XRD) to allow for the simultaneous characterization of polycrystalline metals at 1MHz or higher. A Kolsky bar was integrated into the synchrotron X-ray source in Sector 32 ID-B at the Advance Photon Source (APS) at Argonne National Laboratory. When the sample is dynamically loaded, the diagnostic methods of full-ring XRD, PCI, and stereo-DIC are properly synchronized to record the deformation behavior at both continuum and microstructural scales as a function of the loading history. An advanced high-strength steel (AHSS) is used as a model material to demonstrate the capabilities of this new experimental method.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Turning Natural Herbaceous Fibers into Advanced Materials for Sustainability

Considering the growing concerns about natural resource depletion, energy inequality, and climate crises, biomass-derived materials—the most abundant organic matter on the planet—have received a lot of attention as a potential alternative to petroleum-based plastics. Herbaceous biomasses and extracted cellulose have recently been extensively used in the development of high-performance and multifunctional materials. Herbaceous biomass has sparked interest due to its species diversity, abundance, low cost, lightweight, and sustainability. This review discusses the structure versus property relationships of various sources of herbaceous biomasses (e.g., sugarcane, straw, and bamboo) and their extracted biomaterials, as well as the latest emerging applications from macro- and microscales to nanoscales. We report, high-strength structural materials, porous carbon materials, multichannel materials, and flexible materials are examples of these applications, which include sustainable electronics, environmentally friendly energy harvesting, smart materials, and biodegradable structural buildings.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Gradient nanostructuring via compositional means

Nanocrystalline metals are inherently unstable against thermal and mechanical stimuli, commonly resulting in significant grain growth. Also, while these metals exhibit substantial Hall-Petch strengthening, they tend to suffer from low ductility and fracture toughness. With regard to the grain growth problem, alloying elements have been employed to stabilize the microstructure through kinetic and/or thermodynamic mechanisms. And to address the ductility challenge, spatially-graded grain size distributions have been developed to facilitate heterogeneous deformation modes: high-strength at the surface and plastic deformation in the bulk. In the present work, we combine these two strategies and present a new methodology for the fabrication of gradient nanostructured metals via compositional means. Here, we have demonstrated that annealing a compositionally stepwise Pt-Au film with a homogenous microstructure results in a film with a spatial microstructural gradient, exhibiting grains which can be twice as wide in the bulk compared to the outer surfaces. Additionally, phase-field modeling was employed for the comparison with experimental results and for further investigation of the competing mechanisms of Au diffusion and thermally induced grain growth. This fabrication method offers an alternative approach for developing the next generation of microstructurally stable gradient nanostructured films.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Deuterium trapping mechanisms in reduced activation ferritic martensitic steels and their correlation with mechanical strengthening

Development of high-strength materials often involves introduction of additional strengthening microstructures that also serve as tritium trapping sites. Such additions in fusion material development could degrade the fuel efficiency in fusion reactors and raise radiological concerns. The contribution of individual microstructure features in hydrogen trapping must be evaluated to ensure fuel efficiency and radiological safety. This study explores the mechanistic origins of deuterium trapping in reduced-activation ferritic–martensitic steels and its correlation to mechanical strengthening. A series of model alloys and engineering steels were fabricated and subjected to different heat treatments to control deuterium trapping site density. Deuterium retention was evaluated using D 2 gas charging and thermal desorption spectroscopy, focusing on the role of grain boundary, dislocation, M 23 C 6 precipitates, and TiC precipitates. Multiscale microstructure characterization and synchrotron X-ray diffraction were performed to characterize microstructure, which was correlated to the deuterium retention property. Results show that TiC precipitates exhibit the highest deuterium trapping capacity, followed by M 23 C 6 precipitates. Dislocation and grain boundary demonstrate the lowest and similar efficiencies. Furthermore, the relationship of trapping quantity and mechanical strengthening of these microstructure features was quantified, demonstrating that TiC precipitates offer highest deuterium trapping per unit of mechanical strengthening.

Retention↗
DOE OSTI2021

Large-scale additive manufacturing tooling for extrusion-compression molds

Carbon fiber reinforced polymer composites (CFPC) have been used in additive manufacturing (AM) due to both the high-strength-to-weight and superior-stiffness-to-weight ratios. CF AM is being considered for tooling applications. In AM, CFPCs are usually aligned along the deposition direction; however, it results in anisotropic thermal properties which affect the heat transfer and warpage of the final part. In this study, three male molds with different infill patterns were produced via the material extrusion additive manufacturing (EDF-AM) process. These include (a) 0°: infill pattern along the printing direction; (b) 90°: infill pattern perpendicular to the printing direction; and (c) 0°/90°: alternate layers along and perpendicular directions. The effect of the infill pattern on thermal conductivity was analyzed and observed that 0° infill (surface temperature: 79.2°C) had the highest conductivity; and 90° infill (surface temperature: 66.4°C) had the least.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Assessment of critical flaw sizes and crack driving forces during additive manufacturing of metallic materials

Additive manufacturing (AM) of complex engineering components is often plagued by a high susceptibility to cracking, particularly in high-strength metallic materials. While alloy design efforts have made progress in mitigating solidification defects, there remains a need for mechanistic guidelines to predict susceptibility to solid-state cracking. To address this gap, driving forces for the growth of melt pool cracks are calculated across a wide range of alloys using an efficient computational framework. Calculations are coupled with rapid single track laser experiments to elucidate trends in cracking from laser melting. The analyses conducted here highlight the important role of material properties in susceptibility to cracking, notably fracture toughness and elastic modulus. An important finding is that residual stresses that are limited in magnitude to the yield stress of the material are likely insufficient to drive cracking during cooling. Furthermore, the implications of these results are discussed in the context of alloy design for AM and residual stress accumulation during AM.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Design of a 2 MW ZrC/W-based molten-salt-to-sCO 2 PCHE for concentrated solar power

To increase the power cycle efficiency and lower the levelized cost of electricity (LCOE) of concentrated solar power (CSP) plants, printed circuit heat exchangers (PCHEs) capable of operating above 700 °C with molten chloride salt and a sCO 2 -based fluid are needed. In this paper, the design of a high-pressure, high-temperature, 2 MW PCHE comprised of a thermomechanically-robust, zirconium carbide/tungsten (ZrC/W) composite is conducted for CSP plants. The ZrC/W composite is a material with high thermal conductivity, high stiffness, and high failure strength at high temperatures, along with excellent resistance to thermal cycling and thermal shock. In this work, a thermomechanical design analysis was conducted to select appropriate material thicknesses of the ZrC/W plates, and to determine the geometrical dimensions and the thermal performance of the PCHE. The influences of the plate number and heat exchanger length on power density and pressure drop have also been systematically investigated. Economic analyses were conducted to compare the cost of ZrC/W-based PCHEs to those comprised of IN740H (a state-of-the-art, nickel-based superalloy) and 316 stainless steel (316SS). Finally, at a sufficiently high plate production rate, the manufacturing cost of ZrC/W-based PCHEs can be significantly lower, while achieving a much higher power density, compared with state-of-the-art, nickel alloy-based and stainless steel-based PCHEs.

14 SOLAR ENERGY↗
DOE OSTI2020

Overcoming geometric limitations in metallic glasses through stretch blow molding

Bulk metallic glasses (BMGs) exhibit remarkable mechanical properties, such as high strength and elasticity, which is often paired with fracture toughness. Their supercooled liquid region gives rise to plastic-like processing and suggests parts and shapes that can otherwise not be obtained for crystalline metals. However, current processing techniques only allow for limited options in terms of geometry, thicknesses uniformity, and shape complexity. Here we introduce a new processing technique, “stretch blow molding,” to expand the range of possible parts and increase the available geometries that can be fabricated with BMGs. Additionally, a model is derived that allows for the quantification and prediction of stretch blow molding and provides insight into its potential use and limitations. We demonstrate that with stretch blow molding overall strains exceeding 2000% are achievable, compared to the previously reported ~150% of blow molding. With the ability to stretch blow mold shapes that were previously unachievable with any other metal fabrication technique in a fast and economical manner, and the superb properties of BMGs, we look forward to a broad commercial adaptation of this technique.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Tribological behaviors of nanotwinned Al alloys

Wear-induced damages cause significant materials loss each year. Al alloys are widely used by industry but usually have low wear resistance. Here, we compare the tribological behaviors of ultrafine grained Al, a nanoprecipitate hardened Al 7075 alloy and nanotwinned Al–Ni alloys using the nanoscratch. The nanotwinned Al–Ni alloys exhibit lower coefficient of friction and much greater wear resistance than the Al and Al 7075 alloys. Additionally, the enhanced wear properties of Al–Ni alloys arise from their high strength and the evolution of nanotwinned microstructures into gradient nanograins during wear. These findings on fundamental wear mechanisms in nanotwinned alloys may advance the discovery of wear-resistant metallic materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Optimization based process modeling of an anaerobic membrane bioreactor system: Application to swine wastewater

To maintain current levels of consumption in the economy with the dwindling supply of non-renewable material and energy, alternative resource streams more traditionally viewed as waste streams must be considered. Fermentation of high-strength wastewaters is one such pathway that allows for the recovery of energy, nitrogen, phosphorus, and carbon compounds. Anaerobic membrane bioreactors (AnMBRs) are an emerging technology that allow for the digestion of wastewater in a much smaller footprint than traditional anaerobic digesters. Adoption of this technology into industry has been limited by membrane capital and cleaning costs, but these costs may be offset through the recovery of valuable products. To evaluate the viability of AnMBR technology in the context of swine wastewater treatment, an optimization-based process model built upon Anaerobic Digestion Model No. 1 (ADM1) has been developed. Modeling results show that a swine wastewater stream provides potential for net positive energy generation from the AnMBR system in most cases. Sensitivity analyses around important variables were conducted to determine focus areas for future research into AnMBR technology and evaluate the robustness of the model to microbial variables that may change with different microbial communities.

09 BIOMASS FUELS↗