Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “high efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Spontaneously supersaturated nucleation strategy for high reproducible and efficient perovskite solar cells

High-quality perovskite films are predominantly prepared by anti-solvent assisted spin-coating method. How- ever, small device size and narrow operation window limit their applications in practical and scalable production. Here, a spontaneously supersaturated nucleation strategy is developed to fabricate high-quality perovskite films without any antisolvents. The rapid precipitation behavior of the precursor solutions could be triggered by the volatilization of methylamine ethanol at the initial film formation stage, forming uniform and compact intermediate phase films. Mirror-like large area (10 cm × 10 cm) methylammonium lead triiodide (MAPbI 3 ) perovskite films with micrometer-sized grains can be achieved by phase transition via annealing. The average power conversion efficiency (PCE) of 19.4% is achieved for 0.1 cm 2 perovskite solar cells (PSCs). The 1 cm 2 device shows a PCE of 17.57% and retains 96.8% after aging for 39 days in the air with a relative humidity of 5–30%. The perovskite module based on the perovskite films prepared by our strategy exhibits a PCE of 13.13%. Here, the perovskite film fabrication method developed in this work shows high reproducibility of the fabrication process due to the spontaneous nucleation process. Meanwhile, it also exhibits significant potential in the application of scalable solution processing deposition techniques toward the commercialization of PSCs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Developing Stable Critical Materials and Microstructure for High-Flux and Efficient Hydrogen Production through Reversible Solid Oxide Cells

Reversible Solid Oxide Cells (RSOCs), which operate as either Solid Oxide Fuel Cells (SOFCs) or Solid Oxide Electrolytic Cells (SOECs), hold great promise for clean, high-efficiency energy conversion and hydrogen production. However, their commercial potential is hindered by stability issues arising from temperature-induced materials degradation. While substantial progress has been made in developing durable, reduced-temperature SOFCs - bringing them closer to commercial deployment, SOECs still exhibit substantially higher degradation rates at both the cell and stack levels under practical operating conditions.

08 HYDROGEN↗
DOE OSTI2025

Bio‐Inspired Cascade Photocatalysis on Fe Single‐Atom Carbon Nitride Upcycles Plastic Wastes for Effective Acetic Acid Production

Plastic imposes a critical threat to the environment, ecosystems, and human health because of the low utilization efficiency of plastics. Here, we demonstrate a sustainable, highly efficient cascade photocatalysis for upcycle plastics to value-added acetic acid using Fe single-atom catalysts (Fe@C 3 N 4 SAC) at ambient conditions. Inspired by Phanerochaete chrysosporium microbial, the defective Fe@C 3 N 4 SAC acts as a bifunctional cascade photocatalyst for both Fenton-like and CO 2 reduction reactions. During the reaction, hydroxyl radicals (*OH) form and subsequently oxidize plastics into CO 2 intermediates. These CO 2 intermediates are then photo-reduced to CH 3 COOH on the same catalyst via cascade photocatalysis. The mechanism is confirmed by in situ multimodal microscopy and spectroscopies, with density functional theory calculations. A state-of-art CH 3 COOH yield of 63.8 mg h −1 gcat −1 from PVC, 12.7 mg h −1 gcat −1 from PE, 5.4 mg h −1 gcat −1 from PET, and 5.3 mg h −1 gcat −1 from PP are directly obtained under AM1.5G solar irradiation and further validated under real sunlight (≈0.6 sun), achieving 5.6 mg h −1 gcat −1 from PET, using low-cost Fe@C 3 N 4 SAC in a sealed reactor by enhancing the photon transport and utilization efficiency. The techno-economic analysis shows it is promising to practically mitigate plastic based on broader social welfare assessments.

cascade photocatalysis↗
DOE OSTI2023

Rational design of septenary high-entropy alloy for direct ethanol fuel cells

Promoting C–C bond cleavage of ethanol by a complete 12-electron (12e) ethanol oxidation reaction (EOR) is a grand challenge for the development of highly efficient direct ethanol fuel cells (DEFCs). Most state-of-the-art catalysts only implement the EOR in an incomplete 4e or 2e pathway because of the poisoning of the catalysts by strongly adsorbed CO, leading to the poor output performance and low cell efficiency of DEFCs. Herein, a septenary PtPdFeCoNiSnMn high-entropy alloy (PtPd HEA) with a PtPd-rich surface but super-low platinum group metals loading was developed. We identified and proved the functions of each element in the PtPd HEA. The DEFCs assembled with the PtPd HEA (0.12 mg PtPd ∙cm -2 ) achieved a maximum power density of 0.72 W cm -2 and a durable operation for 1,200 h, which outperforms state-of-the-art catalysts for DEFCs. This work will be a design principle for nanostructured alloy development for renewable energy and sustainability applications.

25 ENERGY STORAGE↗
DOE OSTI2026

>24% screen printed Cu contacted n-TOPCon solar cells with successful implementation of LECO process

In this paper, we report the successful fabrication of >24.0 % efficiency n-TOPCon Si solar cells with screen-printed, fire-through Cu contact to n-TOPCon on the rear side and Ag contacted boron emitter on the front side by implementing optimized firing and LECO conditions. The highest efficiency (24.3%) Cu contacted n-TOPCon cell in this study showed excellent cell performance parameters with V oc >730 mV, J sc of 41.1 mA/cm 2 and FF of 80.8%, resulting in an absolute efficiency gap of 0.2% between Cu-contacted and fully Ag contacted n-TOPCon cells (24.5%). The mini-module fabricated with the Cu contacted n-TOPCon cell showed excellent reliability and durability of open-circuit voltage (V oc ), pseudo fill factor (pFF) and efficiency after prolonged damp-heat tests. Such high efficiency screen printed Cu contacted n-TOPCon cells provide unique opportunity to replace very expensive Ag contact on n-TOPCon with cheaper screen printable Cu metal pastes.

14 SOLAR ENERGY↗
DOE OSTI2021

Continuous Fly-Through High-Temperature Synthesis of Nanocatalysts

Conventional thermal treatment system, such as muffle and tube furnaces, typically feature low ramping and cooling rates, which lead to steep thermal gradients during bulk material synthesis that generate inefficient, non-uniform reaction conditions and result in nanoparticle aggregation. Herein, we demonstrate a continuous fly-through material synthesis approach using a novel high-temperature reactor design based on the emerging thermal-shock technology. By facing two sheets of carbon paper with a small distance apart (1–3 mm), we are able to generate uniform, ultra-high temperatures that can reach up to 3200 K within 50 ms by simply applying a voltage of 15 V. We can control this high-temperature to enable ultrafast chemical reactions by continuously feeding raw materials through the device from one end to the other, allowing the final products to be rapidly collected. As a proof-of-concept demonstration, we synthesized Pt nanocatalysts ~4 nm in size anchored to carbon black via this fly-through high-temperature reactor at ~1400 K. Furthermore, we find these supported Pt nanoparticles feature excellent electrocatalytic activities toward methanol oxidation reaction. Compared to existing heating methods, this continuous fly-through high temperature reactor offers a new and highly efficient platform for the synthesis of nanomaterials at high temperatures.

Qiao, Yun↗
DOE OSTI2025

Explainable artificial intelligence relates perovskite luminescence images to current-voltage metrics

As the demand for low-cost, high-efficiency solar energy technologies grows, metal halide perovskite (MHP) solar cells have emerged as a promising candidate for next-generation photovoltaics due to their high power conversion efficiencies. However, their poor durability and issues with manufacturing consistency remain significant barriers to commercialization. In this work, we develop deep learning models to support materials characterization and provide insight into features and processes influencing performance. The models are trained using transfer learning of a pretrained model to predict relevant current-voltage (IV) metrics based on different combinations of input electroluminescence (EL) and photoluminescence (PL) images of MHP devices. We examine which image types are most informative in accurately predicting different IV metrics. Additionally, we use explainable artificial intelligence (XAI) techniques to provide insights into specific spatial features in the devices that drive differences in performance. We find that stabilized luminescence images (e.g. those collected after biasing the devices for at least 1 min) are better for predicting metrics of open-circuit voltage (by PL) and short-circuit current (by PL with EL), but that predicting fill factor and overall power output may use the time-evolution of EL images. Based on attribution masks generated by integrated gradients for each device performance metric, we further suggest different loss mechanisms associated with categories of large and small spatial defects. Overall, this case study highlights the potential applicability of XAI methodology for streamlining MHP device analysis and accelerating detailed understanding of the relationships between spatial defects and impacts on performance.

14 SOLAR ENERGY↗
DOE OSTI2024

Photo-accelerated oxidation of spiro-OMeTAD for efficient carbon-based perovskite solar cells

Metal halide perovskite thin film solar cell (PSC) technology demonstrates promising power conversion efficiency and paves the way to commercialization. So far, the best device performance originates from the n-i-p structure with FTO/SnO 2 /perovskite/Spiro-OMeTAD/Au device architecture. Traditionally, to achieve high efficiency, several hours of oxidization of a Li-doped Spiro-OMeTAD hole transport layer (HTL) is necessary, which hinders the application of Spiro-OMeTAD for rapid large-scale manufacturing. In particular, the oxidization process significantly relies on ambient conditions, including oxygen and moisture levels. In this work, we report a fast technique to accomplish rapid oxidation in several mins of Spiro-OMeTAD HTL in perovskite solar cells by illuminating in visible light with one Sunlight intensity (100 mW cm −2 ). Compared to the traditional approach, our photo-accelerated oxidization of Spiro-OMeTAD approach can deliver a high-power conversion efficiency. We employ this photo-accelerated oxidization for the planar carbon-based perovskite solar cell and achieve a champion device efficiency of 17.47%. This strategy overcomes the barriers for a simple and rapid means toward mass manufacturing and industrial applications by utilizing Spiro-OMeTAD as the HTL for the perovskite solar module.

14 SOLAR ENERGY↗
DOE OSTI2020

Examination of Solvent- Room Temperature Ionic Liquid Interactions using 2D NMR and Computational Chemistry

Rare earth metals (REMs) are the key functioning material found in microelectronics, advanced batteries, and high-efficiency electrical motors. Current methods for producing REMs require high temperatures (i.e. energy intensive) and produce an abundance of hazardous fluoride waste. Room temperature ionic liquids (RTILs) are an ideal alternative electrolyte because they allow for a low-temperature, energy-efficient electrochemical process. RTIL properties such as viscosity and conductivity determine how effective they can be in this process. Since viscosity is directly related to both intra and intermolecular forces, this study sets out to investigate two RTILs-Trihexyltetradecylphosphonium dicyanamide (Cyphos 105) and Trihexyltetradecylphosphonium bistrifimide (Cyphos 109) and their interactions. Results from 2-dimensional nuclear magnetic resonance (2D NMR) spectroscopy show that there is an interaction between the tetradecyl tail and the phosphorus atom of the Cyphos RTIL. In order to establish whether this is an intra or an inter-molecular interaction, DFT-based computational calculations were performed to determine the optimized geometry. Calculations were done both in the gas phase and with propylene carbonate as an augmenting solvent. Preliminary results show that there is minimal intramolecular interaction between the tetradecyl tail and the phosphorus atom of the RTILs, and that the interaction seen in the 2D NMR experiment is likely of an intermolecular nature instead.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

3-D Modeling off the CFR Engine for the Investigation of Knock on Natural Gas

Engine knock and misfire are barriers to pathways leading to high-efficiency Natural Gas (NG) engines. The general tendency to knock is highly dependent on engine operating conditions and the fuel reactivity. The problem is further complicated by low emissions limits and the wide range of chemical reactivity in pipeline quality NG (65< MN<95). In order to realize diesel-like efficiencies, spark-ignited NG engines must be designed to operate at high BMEP near knock limits over a wide range of fuel reactivity. This requires a deep understanding regarding combustion-engine interactions important in flame propagation and end-gas autoignition. The present work highlights a three-dimensional computational fluid dynamics (CFD) model of the Cooperative Fuel Research (CFR) engine to investigate knock behavior with NG. The CFR engine model is used to investigate fuel-engine interactions that lead to knock with NG, including effects of fuel reactivity, engine operating parameters, and exhaust gas recirculation (EGR). Cylinder wall, piston, valves, and port surface temperatures are estimated with a 1-D Three-Pressure Analysis (TPA) model. Model validation was performed by comparing model predictions with experimental data taken with a CFR engine over varying compression ratio, CA50, EGR fraction and BMEP.

Bestel, Diego↗
DOE OSTI2024

Characterization of High-Temperature SiPM Noise

Introduction • Background: Silicon photomultipliers (SiPMs) are compact, low-power, and high-efficiency detectors that are increasingly used in radiation detection applications like medical imaging and nuclear safeguards. The have advantages of PMTs because they are smaller, operate at lower voltages, and offer high photon detection efficiency. • Challenges: SiPMs suffer from increased dark count rate (DCR) and optical crosstalk (OCT), which degrades performance. • Purpose of study: This study compares the Advansid ASD-NUV3S-P-40, Broadcom AFBR-S4K33C0147L, and Onsemi MicroFJ-30035-TSVTR under four different temperatures to compare their performance in harsh environments.

Fritchie, Jacob↗
DOE OSTI2024

17.2% Efficient CdSexTe1−x solar cell with (InxGa1−x)2O3 emitter on lightweight and flexible glass

High-efficiency, lightweight, and flexible solar cells are sought for a variety of applications particularly when high power density and flexible form factors are desired. Development of solar cells on flexible substrates may also offer production advantages in roll-to-roll or sheet-to-sheet processes. Here, we report device efficiencies of 17.2% and 14.6%, under AM1.5G and AM0 irradiances, respectively, for a flexible, lightweight, CdTe-based solar cell. To advance the efficiency relative to the highest previously reported AM1.5G value of 16.4%, we used an indium gallium oxide (IGO) emitter layer on a cadmium stannate (CTO) transparent conductor, which was deposited on 100-μm thick Corning® Willow® Glass. A sputtered CdSe layer was employed to incorporate Se into a CdTe absorber that was deposited by close-space sublimation, and CuSCN was used as a hole transport layer between the CdTe and the back metal electrode. The IGO and CTO layers remained intact during the high temperature film processing as seen in cross-sectional imaging and elemental mapping. This device configuration offers great promise for building-integrated photovoltaics, space applications, and higher rate manufacturing.

Physics↗
DOE OSTI2020

CONTROLLED END GAS AUTO IGNITION WITH EXHAUST GAS RECIRCULATION ON A STOICHIOMETRIC, SPARK IGNITED, NATURAL GAS ENGINE

The goal of this study is to address fundamental limitations to achieving diesel-like efficiencies in heavy duty on-highway natural gas (NG) engines. Engine knock and misfire are barriers to pathways leading to higher efficiency engines. This study explores enabling technologies for development of high efficiency stoichiometric, spark ignited, natural gas engines. These include design strategies for fast and stable combustion and higher dilution tolerance. Additionally, advanced control methodologies are implemented to maintain stable operation between knock and misfire limits. To implement controlled end- gas autoignition (C-EGAI) strategies a Combustion Intensity Metric (CIM) is used for ignition control with the use of a Woodward large engine control module (LECM). Tests were conducted using a single cylinder, variable compression ratio, cooperative fuel research (CFR) engine with baseline conditions of 900 RPM, engine load of 800 kPa indicated mean effective pressure (IMEP), and stoichiometric air/fuel ratio. Exhaust gas recirculation (EGR) tests were performed using a custom EGR system that simulates a high pressure EGR loop and can provide a range of EGR rates from 0 to 40%. The experimental measurements included the variance of EGR rate, compression ratio, engine speed, IMEP, and CIM. These five variables were optimized through a Modified Box- Benken design Surface Response Method (RSM), with brake efficiency as the merit function. A positive linear correlation between CIM and f-EGAI was identified. Consequently, CIM was used as the feedback control parameter for C-EGAI. As such, implementation of C-EGAI effectively allowed for the utilization of high EGR rates and CRs, controlling combustion between a narrower gap between knock and lean limits. The change from fixed to parametric ignition timing with CIM targeted select values of f-EGAI with an average coefficient of variance (COV) of peak pressure of 5.4. The RSM efficiency optimization concluded with operational conditions of 1080 RPM, 1150 kPa IMEP, 10.55:1 compression ratio, and 17.8% EGR rate with a brake efficiency of 21.3%. At this optimized point of peak performance, a f-EGAI for C-EGAI was observed at 34.1% heat release due to auto ignition, a knock onset crank angle value of 10.3° aTDC and ignition timing of - 24.7° aTDC. This work has demonstrated that combustion at a fixed f-EGAI can be maintained through advanced ignition control of CIM without experiencing heavy knocking events.

Cooperative Fuel Research Engine, Auto Ignition, E↗
DOE OSTI2021

Effects of Applied Interfacial Pressure on Li-Metal Cycling Performance and Morphology in 4 M LiFSI in DME

Lithium-metal anodes can theoretically enable 10x higher gravimetric capacity than conventional graphite anodes. However, Li-metal anode cycling has proven difficult due to porous and dendritic morphologies, extensive parasitic solid electrolyte interphase reactions, and formation of dead Li. We systematically investigate the effects of applied interfacial pressure on Li-metal anode cycling performance and morphology in the recently developed and highly efficient 4 M lithium bis(fluorosulfonyl)imide in 1,2-dimethoxyethane electrolyte. We present cycling, morphology, and impedance data at a current density of 0.5 mA/cm 2 and a capacity of 2 mAh/cm 2 at applied interfacial pressures of 0, 0.01, 0.1, 1, and 10 MPa. Cryo-focused ion beam milling and cryo-scanning electron microscopy imaging in cross section reveal that increasing the applied pressure during Li deposition from 0 to 10 MPa leads to greater than a fivefold reduction in thickness (and therefore volume) of the deposited Li. This suggests that pressure during cycling can have a profound impact on the practical volumetric energy density for Li-metal anodes. A “goldilocks zone” of cell performance is observed at intermediate pressures of 0.1–1 MPa. Increasing pressure from 0 to 1 MPa generally improves cell-to-cell reproducibility, cycling stability, and Coulombic efficiency. However, the highest pressure (10 MPa) results in high cell overpotential and evidence of soft short circuits, which likely result from transport limitations associated with increased pressure causing local pore closure in the separator. All cells exhibit at least some signs of cycling instability after 50 cycles when cycled to 2 mAh/cm 2 with thin 50 μm Li counter electrodes, though instability decreases with increasing pressure. In contrast, cells cycled to only 1 mAh/cm 2 perform well for 50 cycles, indicating that capacity plays an important role in cycling stability.

25 ENERGY STORAGE↗
DOE OSTI2019

Prediction of room-temperature half-metallicity in layered halide double perovskites

Half-metallic ferromagnets (HMFs) that possess intriguing physical properties with completely spin-polarized current are key candidates for high-efficiency spintronic devices. However, HMFs that could simultaneously have high Curie temperature ( T c ), wide half-metallic gap (Δ HM ), and large bulk magnetocrystalline anisotropy energy (MAE) are very rare, which significantly restrict their room-temperature (RT) applications. In this article, through materials screening in layered halide double perovskites (LHDPs), we have theoretically identified that Cs 4 FePb 2 Cl 12 , which has good crystallographic, dynamic and thermal stabilities, possesses an intrinsic half-metallic ground-state with a high T c ~ 450 K. Interestingly, the long-range ferromagnetic ordering in bulk Cs 4 FePb 2 Cl 12 is contributed by the strong super-superexchange interactions between the neighboring Fe d orbitals mediated by different anionic Cl p orbitals. The high T c of layered Cs 4 FePb 2 Cl 12 can be well maintained even in the monolayer limitation, i.e., T c ~ 370 K for Cs 4 FePb 2 Cl 12 monolayer, which is critical for nanoscale device applications. Moreover, both bulk and monolayer Cs 4 FePb 2 Cl 12 can exhibit wide Δ HM ~ 0.55 eV and large MAE >320 μeV/Fe, comparable to that of the best HMFs reported in the literature. Our findings can significantly extend the potentials of LHDPs for high-temperature spintronic applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Synergistic effects of Pd single atoms and nanoclusters boosting SnO 2 gas sensing performance

Tin(IV) oxide-supported Pd is a promising heterogenous catalyst for CO oxidation relevant for environmental cleanup reactions. In this study, an atomically dispersed Pd catalyst on SnO 2 (ADC Pd/SnO 2 ) hybrid material is successfully synthesized via a straightforward wet chemistry method and is found to exhibit superior performance toward CO sensing. Ex situ EXAFS analysis confirms the formation of single Pd atoms and small Pd nanoclusters stabilized on the SnO 2 (110) surface. Further, the material exhibits high efficiency in generating adsorbed O 2 - as well as high activity in catalyzing CO oxidation at low temperatures, resulting in exceptional sensitivity and selectivity toward CO in comparison to pure SnO 2 and Pd nanoparticles loaded on SnO 2 respectively. In situ FTIR measurements unravel CO adsorption kinetics on ADC Pd/SnO 2 under reaction conditions, and a possible sensing mechanism is put forth in which CO is transformed into CO 2 by reaction with active oxygen species; and concurrently, carbon-related species (bicarbonates and carbonates) are formed and decomposed into CO 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

A flexible neutron spectrometer concept with a new ultra-high field steady-state vertical-bore magnet

The proposed facility explores materials under ultra-high magnetic fields. By combining the power of high fields to tune materials and of neutron scattering to probe the resulting changes down to the atomic scale, this facility will enable transformative progress in the study of quantum materials and is named for the “TITAN” subset of Greek gods to reflect this transformation. TITAN will offer DC magnetic fields up to at least 20 T. Exploiting the record brightness and bandwidth of the Second Target Station at the Spallation Neutron Source, TITAN will probe atomic-scale responses through high efficiency neutron spectroscopy up to 80 meV energy transfer, high resolution diffraction, and small angle neutron scattering. Focusing neutron optics will maximize flux on accurately positioned samples, while radial collimation and optimized shielding and detection strategies will minimize backgrounds.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Soft x-ray high-harmonic generation in an anti-resonant hollow core fiber driven by a 3 μ m ultrafast laser

High-harmonic upconversion driven by a mid-infrared femtosecond laser can generate coherent soft x-ray beams in a tabletop-scale setup. Here, we report on a compact ytterbium-pumped optical parametric chirped pulse amplifier (OPCPA) laser system seeded by an all-fiber front-end and employing periodically poled lithium niobate (PPLN) nonlinear media operated near the pulse fluence limits of current commercially available PPLN crystals. The OPCPA delivers 3 µm wavelength pulses with 775 µJ energy at 1 kHz repetition rate, with transform-limited 120 fs pulse duration, diffraction-limited beam quality, and ultrahigh 0.33% rms energy stability over >18 h. Using this laser, we generate soft x-ray high harmonics (HHG) in argon gas by focusing into a low-loss, high-pressure gas-filled anti-resonant hollow core fiber (ARHCF), generating coherent light at photon energies up to the argon L-edge (250 eV) and carbon K-edge (284 eV), with high beam quality and ∼1% rms energy stability. This work demonstrates soft x-ray HHG in a high-efficiency guided-wave phase matched geometry, overcoming the high losses inherent to mid-IR propagation in unstructured waveguides, or the short interaction lengths of gas cells or jets. The ARHCF can operate in the long term without damage and with the repetition rate, stability, and robustness required for demanding applications in spectromicroscopy and imaging. Finally, we discuss routes for further optimizing the soft x-ray HHG flux by driving He at higher laser intensities using either the signal (1.5 μm) or idler wavelengths (3 μm).

Femtosecond lasers↗