Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “graphitization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Development of polyphenylquinoxaline graphite composites

The potential of polyphenylquinoxaline (PPQ)/graphite composites to serve as structural material at 316 C (600 F)has been demonstrated using a block copolymer, BlCo(13), PPQ derivative. Initially, thirteen polyphenylquinoxalines were evaluated. From this work, four candidate polymers were selected for preliminary evaluation as matrices for HMS graphite fiber reinforced composites. The preliminary composite evaluation enabled selection of one of the four polymers for advanced composite preparation and testing. Using an experimentally established cure schedule for each of the four polymers, preliminary laminates of 50% resin volume content, prepared without postcure, were tested for flexure strength and modulus, interlaminar shear strength (short beam), and tensile strength and modulus at ambient temperature. A block copolymer (Bl Co 13) derived from one mole p-bis (phenylglyoxalyl) benzene, one fourth mole 3,3'-diaminobenzidine and three-fourths mole 3,3', 4,4'-tetraminobenzophenone was selected for extensive study. Tensile, flexural, and interlaminar shear values were obtained after aging and testing postcured BlCo(13) laminates at 316 C (600 F). The potential of PPQ/graphite laminates to serve as short term structural materials at temperatures up to 371 C (700 F) was demonstrated through weight loss experiments.

Hoggatt, J. T.↗
NASA NTRS1972

Graphite epoxy reflector support truss for applications technology satellite /ATS/.

The design, development, fabrication, and qualification load testing of the reflector support truss for Applications Technology Satellites F and G are described. Because the truss is stability-critical, high modulus graphite epoxy composite was used to provide a minimum weight structure. The work was performed under the sponsorship of the NASA Goddard Space Flight Center with Fairchild Industries as the prime contractor.

Randolph, R. E.↗
NASA NTRS1972

Lubricating characteristics of polyimide bonded graphite fluoride and polyimide thin films.

A friction and wear life study was conducted on the use of a polyimide (PI) varnish as a binder for the solid lubricant, graphite fluoride (CF sub 1.1) sub n. Also studied were the lubricating properties of PI thin films with no solid lubricant additives. For comparison, similar experiments on PI-bonded MoS2 and burnished films of MoS2 or (CF sub 1.1) sub n were conducted. The best results were obtained with the PI-bonded (CF sub 1.1) sub n films. The polyimide thin films (with no solid lubricant additives) did not lubricate well at 25 C; however, when heated to 100 C, low friction and long wear lives were obtained.

Fusaro, R. L.↗
NASA NTRS1973

High-energy electron-beam deposition onto a hot graphite surface.

The momentum transfer and blow-off vapor yield resulting from the deposition of a pulsed high-power electron beam onto a plane graphite target with surface temperatures of 300 K and 5000 K are examined experimentally. The results show that with identical electron beams the momentum transfer and vapor yield are between two and three times larger when irradiating the 5000 K surface as compared with the 300 K surface.

Robin, J. E.↗
NASA NTRS1973

Development of polyphenylquinoxaline graphite composites.

The potential of polyphenylquinoxaline (PPQ)/graphite composites to serve as structural material at 316 C (600 F) has been demonstrated using a block copolymer, BICo(1:3), PPQ derivative. Initially, 13 polyphenylquinoxalines were evaluated. From this work, four candidate polymers were selected for preliminary evaluation as matrices for HMS graphite fiber reinforced composites. The preliminary composite evaluation enabled selection of one of the four polymers for advanced composite preparation and testing. Using an experimentally established cure schedule for each of the four polymers, preliminary laminates of 50% resin volume content, prepared without postcure, were tested for flexure strength and modulus, interlaminar shear strength (short beam), tensile strength, and modulus of ambient temperature. The potential of PPQ/graphite laminates to serve as short term structural materials at temperatures up to 371 C (700 F) was demonstrated through weight loss experiments.

Shdo, J. G.↗
NASA NTRS1973

Graphite oxidation at low temperature in subsonic air.

Coupled mass loss and heat transfer was studied experimentally for thin two inch diameter graphite disks heated as high as 2800 F in a flow of ambient air at velocities of 97 to 717 ft/sec. Oxidation was predominately reaction rate controlled with rate constants which were determined experimentally for POCO AXF 5Q, ATJ, ATJS, and an AVCO 3D Orthogonal material. The specimen thermal response was used with an energy balance to obtain the influence of mass loss and chemical reactions on the heat transfer. Specimen heating due to exothermic reactions correlates qualitatively with an approximate theory.

Knight, D. D.↗
NASA NTRS1974

Evaluation of graphite composite materials for bearingless helicopter rotor application

Small scale combined load fatigue tests were conducted on twelve unidirectional graphite-glass scrim-epoxy composite specimens. The specimens were 1 in. (2.54 cm) wide by 0.1 in. (.25 cm) thick by 5 in. (12.70 cm) long. The fatigue data was developed for the preliminary design of the spar for a bearingless helicopter main rotor. Three loading conditions were tested. Combinations of steady axial, vibratory torsion, and vibratory bending stresses were chosen to simulate the calculated stresses which exist at the root and at the outboard end of the pitch change section of the spar. Calculated loads for 150 knots (77.1 m/sec) level flight were chosen as the baseline condition. Test stresses were varied up to 4.4 times the baseline stress levels. Damage resulted in reduced stiffness; however, in no case was complete fracture of the specimen experienced.

Ulitchny, M. G.↗
NASA NTRS1974

Development of design data for graphite reinforced epoxy and polyimide composites

Processing techniques and design data were characterized for a graphite/epoxy composite system that is useful from 75 K to 450 K, and a graphite/polyimide composite system that is useful from 75 K to 589 K. The Monsanto 710 polyimide resin was selected as the resin to be characterized and used with the graphite fiber reinforcement. Material was purchased using the prepreg specification for the design data generation for both the HT-S/710 and HM-S/710 graphite/polyimide composite system. Lamina and laminate properties were determined at 75 K, 297 K, and 589 K. The test results obtained on the skin-stringer components proved that graphite/polyimide composites can be reliably designed and analyzed much like graphite/epoxy composites. The design data generated in the program includes the standard static mechanical properties, biaxial strain data, creep, fatigue, aging, and thick laminate data.

Scheck, W. G.↗
NASA NTRS1973

Laboratory simulation of graphite formation in stellar envelopes

A technique has been developed which permits laboratory simulation of graphite condensation in the envelopes of cool, late sequence stars. Processes in the stellar envelope were simulated by allowing hydrogen-carbon mixtures of typical circumstellar composition and temperature to expand freely into vacuum, cooling and supersaturating the vapor. Expansion products were determined mass spectrometrically through the use of molecular beam techniques. The results of laboratory expansions were scaled to those occurring near M and N stars by comparing the number of collisional events in each case. Kinetic considerations indicate that the important rate process in rarefied envelopes will be C2 formation; consequently scaling by termolecular collisions was employed. Results of this study imply that envelope expansions near M giants contribute at most .01 of the observed interstellar grain density. In the case of pulsating N stars, on the other hand, the results are not inconsistent with previous predictions of essentially complete carbon condensation.

Dorfeld, W. G.↗
NASA NTRS1974

Nonequilibrium boundary layer at a stagnation point for a hydrogen-helium stream over ablating graphite

The nonequilibrium axisymmetric stagnation point boundary layer over an ablating graphite surface is considered. The external stream is a high temperature mixture of hydrogen and helium. Variable thermodynamic and transport properties are assumed. Lennard-Jones potential model is used to calculate the transport coefficients of each species. Although the mixture rules for viscosity of the gas mixture are used, the weighting functions are more sophisticated than those commonly employed. For the conductivity of the mixture, generalized Wassiljewa coefficients are used. Seven species with 28 dissociation/recombination reactions are considered. Hansen's model for the dissociation rate constants is employed. The recombination rate constants are obtained by invoking detailed balance principles assisted by the JANAF thermodynamic data and the Hansen-Pearson thermodynamic data for C3.

Liu, T.-M.↗
NASA NTRS1975

Development of high temperature resistant graphite fiber coupling agents

Surface treatments were investigated as potential coupling agents to improve the elevated temperature shear strength retention of polyimide/graphite and polyphenylquinoxaline/graphite composites. The potential coupling agents were evaluated by fiber strand tensile tests, fiber and composite weight losses at 533 and 588K, and by interlaminar shear strength retention at 533 and 588K. The two surface treatments selected for more extensive evaluation were a coating of Ventromer T-1, a complex organometallic reaction product of titanium tetrachloride and trimethyl borate, and a polyphenylquinoxaline (PPQ) sizing which was pyrolyzed in nitrogen to form a carbonaceous layer on the fiber. Pyrolyzed polyphenylquinoxaline is a satisfactory coupling agent for polyimide/Thornel 300 graphite fiber composites. During 1000 hours aging at 588K such composites lose a little over half their transverse tensile strength, and suffer a slight loss in flexural modulus. No degradation of flexural strength or interlaminar shear strength occured during 1000 hours aging at 588K. None of the coupling agents examined had a markedly beneficial effect with polyphenylquinoxaline composites.

Griffin, R. N.↗
NASA NTRS1975

Organopolysiloxane-bonded graphite fluoride as a solid lubricant

A study was conducted on the lubricating properties of organopolysiloxane-bonded graphite fluoride (CF sub 1.1) sub n films. The effects of temperature, atmosphere, composition of organopolysiloxane, and burnishing additional (CF sub 1.1) sub n powder onto the film surface were studied. For comparison, similar experiments were conducted on organopolysiloxane-bonded MoS2 films. The results are equivalent for both films, except that in a moist air environment the wear lives of the films formulated with (CF sub 1.1) sub n are up to 10 times longer than the wear lives of the MoS2-formulated films. Comparison to other (CF sub 1.1) sub n films showed organopolysiloxane films to give better lubrication results than hand-burnished (CF sub 1.1) sub n films but not as good as polyimide-bonded (CF sub 1.1) sub n films.

Fusaro, R. L.↗
NASA NTRS1975

Effects of environment on the fatigue of graphite-epoxy composites

Torsional and flexural fatigue tests were performed on both uniaxial (0 deg) and crossplied (plus or minus 45 deg) graphite-epoxy materials at temperatures of 24 and 74 C in environments of air and water. The results of the torsion testing showed that the number of cycles required to cause an initial decrease in stiffness as well as the rate of stiffness loss was a function of temperature and environment; the most significant losses were noted for tests at the higher temperature in water. The torsional fatigue specimens were subsequently tested in four-point bending to determine the effect of torsional damage on longitudinal properties. This damage caused changes in the flexural stiffness, failure stress, and failure energy, depending on the stress and environmental histories. The flexural fatigue tests also showed a significant effect of water (at 24 C) on the material behavior. These results are compared with the results of previous investigations and are discussed in terms of proposed damage mechanisms.

Sumsion, H. T.↗
NASA NTRS1974

Tensile properties of an ultrahigh-strength graphite fiber in an epoxy matrix

The fiber performance and reinforcement potential for fiber composites of a special PAN-based graphite fiber were evaluated by testing the fiber's tensile properties in an epoxy matrix. Representative strand samples were taken from 30 spools of single-end, 1500-filament fiber to make over 5000 fiber/epoxy strand specimens using the filament-winding process. Characteristics studied were fiber uniformity, strength and modulus distributions at room and liquid-nitrogen temperatures, stress-strain behavior, the effect of strain rate on fiber strength, and acoustic emission during tensile loading to failure. The fiber was found to have a 3570-MPa failure stress, a 1.7% failure strain, a 206-GPa modulus, and a density of 1.77 Mg/cu m at 23 C. Liquid-nitrogen temperature and various strain rates had no significant effect on fiber tensile properties.

Chiao, T. T.↗
NASA NTRS1976

Graphite-reinforced bone cement

Chopped graphite fibers added to surgical bone cement form bonding agent with mechanical properties closely matched to those of bone. Curing reaction produces less heat, resulting in reduced traumatization of body tissues. Stiffness is increased without affecting flexural strength.

Knoell, A. C.↗
NASA NTRS1975

Thermostructural testing of instrumented ATJ-S graphite nosetip models in the AFFDL 50 MW rent facility

Instrumented ATJ-S graphite shell nosetip models were tested in the AFFDL 50 MW RENT Facility. The inside surface of the models were instrumented with seven thermocouples and three clip-on extensometers. One thermocouple was located at the inside stagnation point and three thermocouples were located at 120 degree intervals on the aft portion of the skirt of the model. In addition, three thermocouples at 120 degree intervals plus three clip-on extensometers at 120 degree intervals offset 60 degrees from the thermocouples were located in the critical region. The outside surface temperature of the models was monitored in two locations by optical pyrometers. Finally, the tests were recorded by three high speed motion picture cameras. Pressure models and calorimeters were also tested in order to help define the flow field condition and heating distribution around the models.

Budde, C. L.↗