Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “circularity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Transonic shock-induced dynamics of a flexible wing with a thick circular-arc airfoil

A simple flexible wing model with an 18-percent circular arc airfoil was constructed and tested in the Langley Transonic Dynamics Tunnel to investigate the dynamic characteristics that a wing might have under these conditions. In the region of shock-boundary layer oscillations, buffeting of the first bending mode was obtained. This mode was well separated in frequency from the shock boundary layer oscillations. A limit cycle oscillation was also measured in a 'third bending-like' mode, involving wing vertical bending and splitter plate motion, which was in the frequency range of the shock-boundary layer oscillations. Several model configurations were tested, and a few potential fixes were investigated.

Bennett, Robert M.↗
NASA NTRS1991

Secondary frequencies in the wake of a circular cylinder with vortex shedding

A detailed numerical study of two-dimensional flow past a circular cylinder at moderately low Reynolds numbers was conducted using three different numerical algorithms for solving the time-dependent compressible Navier-Stokes equations. It was found that if the algorithm and associated boundary conditions were consistent and stable, then the major features of the unsteady wake were well-predicted. However, it was also found that even stable and consistent boundary conditions could introduce additional periodic phenomena reminiscent of the type seen in previous wind-tunnel experiments. However, these additional frequencies were eliminated by formulating the boundary conditions in terms of the characteristic variables. An analysis based on a simplified model provides an explanation for this behavior.

Abarbanel, Saul S.↗
NASA NTRS1991

An experimental trace gas investigation of fluid transport and mixing in a circular-to-rectangular transition duct

An ethylene trace gas technique was used to map out fluid transport and mixing within a circular-to-rectangular transition duct. Ethylene gas was injected at several points in a cross stream plane upstream of the transition duct. Ethylene concentration contours were determined at several cross stream measurement planes spaced axially within the duct. The flow involved a uniform inlet flow at a Mach number level of 0.5. Statistical analyses were used to quantitatively interpret the trace gas results. Also, trace gas data were considered along with aerodynamic and surface flow visualization results to ascertain transition duct flow phenomena. Convection of wall boundary layer fluid by vortices produced regions of high total pressure loss in the duct. The physical extent of these high loss regions is governed by turbulent diffusion.

Reichert, B. A.↗
NASA NTRS1991

Computation of a circular-to-rectangular transition duct flow field

This paper presents the results of a Computational Fluid Dynamics (CFD) calibration study of flow through a circular-to-rectangular transition duct. The design of these ducts is critical to the optimum performance of aircraft with rectangular exhaust nozzles, since these ducts transfer the flow from the gas turbine engine to the exhaust nozzle. Two duct inflow conditions are considered, the first with straight inflow and the second with swirling inflow. Both flows contain realistic wall boundary layers. The first case permits examination of the effects of the geometric transition on the flowfield, while the second case adds in the rotational flow effect that can be present from the gas turbine engine. The flowfields associated with the two cases have been shown, both with CFD and experiment, to have significant differences. The Navier-Stokes CFD code PARC with the Baldwin and Lomax turbulence model was used in this study. The turbulence model had to be modified for both cases in order to achieve accurate determination of the edge of the wall bounded vorticity layers and thus turbulent viscosity. The results of this calibration study will be valuable to aircraft designers who rely on CFD to assist in the design and evaluation of propulsion systems.

Sirbaugh, J. R.↗
NASA NTRS1991

A 29.3-GHz cavity-enclosed aperture-coupled circular-patch antenna for microwave circuit integration

A circular patch antenna fed by an aperture-coupled microstrip line has been demonstrated at 29.3 GHz. The patch was enclosed by a cavity to reduce surface-wave interactions in an array environment and to improve heat dissipation when using active devices. The antenna exhibited a 2:1 input VSWR (voltage standing wave ratio) over a bandwidth of 12 percent from 27.52 to 30.95 GHz. The antenna should have applications in conformal phased arrays at millimeter-wave frequencies.

Navarro, Julio A.↗
NASA NTRS1991

Transient scattering analysis for a circular disk

The backscattered fields of a perfectly conducting circular disk are analyzed from a transient signature viewpoint. The significant dominant scattering mechanisms are identified for both principal polarizations at a variety of angles. Particular attention is given to the edge wave. The backscattered field behavior due to an incident plane wave on a perfectly conducting disk is presented. Good agreement was obtained between the eigenfunction and geometric theory of diffraction solutions. The expected mechanisms from first-, second-, and third-order diffractions with an accurate edge wave representation are demonstrated through the use of transient signatures. The most significant error in the geometric theory of diffraction (GTD) solution occurs in time where the nonprincipal plane double diffraction term exists.

Dominek, Allen K.↗
NASA NTRS1992

Generalized probability model for calculation of interference to the Deep Space Network due to circularly Earth-orbiting satellites

The probability of exceeding interference power levels and the duration of interference at the Deep Space Network (DSN) antenna is calculated parametrically when the state vector of an Earth-orbiting satellite over the DSN station view area is not known. A conditional probability distribution function is derived, transformed, and then convolved with the interference signal uncertainties to yield the probability distribution of interference at any given instant during the orbiter's mission period. The analysis is applicable to orbiting satellites having circular orbits with known altitude and inclination angle.

Ruggier, C. J.↗
NASA NTRS1990

The use of curvilinear fiber format to improve buckling resistance of plates with central circular holes

The potential gain in buckling resistance is explored by using the curvilinear format with a plate containing a centrally located circular hole and subjected to a uniaxial compressive load. The buckling loads for a uniform stress loading and simple support boundary conditions were examined. The method of analysis is outlined for the buckling improvement study. Several designs that represent an improvement over a baseline quasi-isotropic design (a design that is quite good for buckling resistance) are discussed. The tensile load of these designs is examined. A recommended design is presented that not only shows an improved buckling capacity, but also shows improved tensile performance. Follow-on activities are also discussed.

Lee, H. H.↗
NASA NTRS1990

Compression behavior of graphite-epoxy and graphite-thermoplastic panels with circular holes or impact damage

An experimental investigation of the compression behavior of laminated specimens made from graphite-epoxy tape (AS4-3502), graphite-thermoplastic tape (AS4-PEEK), and graphite-thermoplastic fabric (AS4-PEEK) was conducted. Specimens with five different stacking sequences were loaded to failure in uniaxial compression. Some of the specimens had central circular holes with diameters up to 65 percent of the specimen width. Other specimens were subjected to low speed impact with impact energy up to 30 J prior to compressive loading. This investigation indicates that graphite-thermoplastic specimens with holes have up to 15 percent lower failure stresses and strains than graphite-epoxy specimens with the same stacking sequence and hole size. However, graphite-thermoplastic specimens subjected to low speed impact have up to 15 percent higher failure stresses and strains than graphite-epoxy specimens with the same stacking sequence and impact energy. Compression tests of graphite-thermoplastic specimens constructed of unidirectional tape and of fabric indicate that the material form has little effect on failure strains in specimens with holes or low speed impact damage.

Jegley, Dawn C.↗
NASA NTRS1990

Robust, angstrom level circularity profilometry

A noncontacting approach is presented which involves measuring the local circumferential curvature of the test piece by simultaneously measuring its circumferential slope at two slightly displaced locations. A pair of sensing beams is scanned along the circumference, and a profile of curvature is built, from which the circularity profile is deduced. The sensing of curvature makes the approach insensitive to all types of vibration and drift and runout errors in the relative rotation. The special qualities of the approach are summarized which make it well suited to measuring cylindrical optics and enable it to accommodate radii as small as twenty millimeters.

Glenn, Paul↗
NASA NTRS1991

Analysis of a slot loaded microstrip disk antenna for circular polarisation

A method is presented to analyze a circular microstrip disk antenna loaded with a narrow, inclined slot at its center and fed by a coaxial probe. Making use of the exact dyadic Green's functions for a grounded dielectric slab due to electric and magnetic currents, Richmond's reaction integral equation in conjunction with the method of moments (Galerkin), a generalized h-parameter equivalent network for the loaded patch is obtained. An expression for the input impedance of a slot loaded microstrip patch is obtained from the equivalent parameters. The theoretical results are compared with the experiment.

Rao, Y. R.↗
NASA NTRS1991

Constant covariance in local vertical coordinates for near-circular orbits

A method is presented for devising a covariance matrix that either remains constant or grows in keeping with the presence of a period error in a rotating local-vertical coordinate system. The solution presented may prove useful in the initialization of simulation covariance matrices for near-circular-orbit problems. Use is made of the Clohessy-Wiltshire equations and the travelling-ellipse formulation.

Shepperd, Stanley W.↗
NASA NTRS1992

Large quasi-circular features beneath frost on Triton

Specially processed Voyager 2 images of Neptune's largest moon, Triton, reveal three large quasi-circular features ranging in diameter from 280 to 935 km within Triton's equatorial region. The largest of these features contains a central irregularly shaped area of comparatively low albedo about 380 km in diameter, surrounded by crudely concentric annuli of higher albedo materials. None of the features exhibit significant topographic expression, and all appear to be primarily albedo markings. The features are located within a broad equatorial band of anomalously transparent frost that renders them nearly invisible at the large phase angles (alpha greater than 90 deg) at which Voyager obtained its highest resolution coverage of Triton. The features can be discerned at smaller phase angles (alpha = 66 deg) at which the frost only partially masks underlying albedo contrasts. The origin of the features is uncertain but may have involved regional cryovolcanic activity.

Helfenstein, Paul↗
NASA NTRS1992

Compression failure mechanisms of uni-ply composite plates with a circular cutout

The effect of circular-hole size on the failure mode of uniply graphite-epoxy composite plates is investigated experimentally and analytically for uniaxial compressive loading. The test specimens are sandwiched between polyetherimide plastic for nondestructive evaluations of the uniply failure mechanisms associated with a range of hole sizes. Finite-element modeling based on classical lamination theory is conducted for the corresponding materials and geometries to reproduce the experimental results analytically. The type of compressive failure is found to be a function of hole size, with fiber buckling/kinking at the hole being the dominant failure mechanism for hole diam/plate width ratios exceeding 0.062. The results of the finite-element analysis supported the experimental data for these failure mechanisms and for those corresponding to smaller hole sizes.

Khamseh, A. R.↗
NASA NTRS1992

Orbit maintenance for low altitude near-circular lunar orbits

The behavior of low altitude near-circular lunar orbits is a key design issue for some missions in the proposed Space Exploration Initiative. The lunar gravity field strongly perturbs low altitude orbits, so an effective orbit maintenance strategy is needed. This strategy must contend with the long term orbit evolution due to the zonal gravity field. Two possible orbit control scenarios are passive control using a frozen orbit and active orbit control using maneuvers. A maneuver strategy can be designed which optimizes the propellant required for long term orbit sustenance. The long term requirements dominate the total propellant required for orbit control. Additional propellant may be required to offset the impact of medium period gravity field effects. Careful selection of maneuver times and directions, however, can eliminate any medium period penalty.

Cook, Richard A.↗
NASA NTRS1992

Heat transfer in thin, compact heat exchangers with circular, rectangular, or pin-fin flow passages

Heat transfer and pressure drop have been measured of three thin, compact heat exchangers in helium gas at 3.5 MPa and higher, with Reynolds numbers of 450 to 36,000. The flow geometries for the three heat exchanger specimens were: circular tube, rectangular channel, and staggered pin fin with tapered pins. The specimens were heated radiatively at heat fluxes up to 77 W/sq cm. Correlations were developed for the isothermal friction factor as a function of Reynolds number, and for the Nusselt number as a function of Reynolds number and the ratio of wall temperature to fluid temperature. The specimen with the pin fin internal geometry had significantly better heat transfer than the other specimens, but it also had higher pressure drop. For certain conditions of helium flow and heating, the temperature more than doubled from the inlet to the outlet of the specimens, producing large changes in gas velocity, density, viscosity, and thermal conductivity. These changes in properties did not affect the correlations for friction factor and Nusselt number in turbulent flow.

Olson, D. A.↗
NASA NTRS1992

The long-term behavior of near-circular orbits in a zonal gravity field

A simple solution has been developed for the long term behavior of a near-circular orbit in a zonal gravity field. The solution is obtained by linearizing the singly averaged variational equations of motion and eliminating a degree of freedom with an integral of motion. The resulting solution is expressed in semiequinoctial elements (h and k), and has either an exponential or periodic form. The type of solution is dependent upon a stability factor determined by the inclination and the values of the gravity field coefficients. Frozen orbits correspond to the equilibrium solutions of the set of simplified variational equations. An approximate expression for the location of these orbits has been developed and can be useful for certain mission design applications.

Cook, Richard A.↗
NASA NTRS1992

Failure mechanisms of uni-ply composite plates with a circular hole under static compressive loading

The objective of the study was to identify and study the failure mechanisms associated with compressive-loaded uniply graphite/epoxy square plates with a central circular hole. It is found that the type of compressive failure depends on the hole size. For large holes with the diameter/width ratio exceeding 0.062, fiber buckling/kinking initiated at the hole is found to be the dominant failure mechanism. In plates with smaller hole sizes, failure initiates away from the hole edge or complete global failure occurs. Critical buckle wavelengths at failure are presented as a function of the normalized hole diameter.

Khamseh, A. R.↗