SEARCH · Engineering Papers

Results for “avionics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

All sources NASA NTRS DOE OSTI

NASA NTRS1983

New results in fault latency modelling

Studies carried out by McGough and Swern (1981, 1983) are summarized. In these studies, an avionics processor was simulated and a series of fault injection experiments was carried out to determine the degree of fault latency in a redundant flight control system that employed comparison monitoring as the exclusive means of failure detection. A determination was also made of the fault coverage of a typical self-test program. The summary presented stresses that a self-test program should be designed to capitalize on the hardware mechanization of the processor. If this is not done, subtests tend to repeatedly exercise the same hardware components while neglecting to exercise a substantial proportion of the remainder. It is also pointed out that fault latency is relatively independent of both the length and instruction mix of a program. A significant difference is found in fault coverage assessed using pin-level and gate-level fault models.

Mcgough, J. G.↗

NASA NTRS1983

Observations of severe in-flight environments on airplane composite structural components

The development of relatively inexpensive, highly sophisticated avionics systems makes it now possible for general aviation aircraft to fly under more severe weather conditions than formerly. Increased instrument flying increases exposure of aircraft to potentially severe thunderstorm activity such as high rain rates, hail stones, and lightning strikes. In particular, the effects of lightning on aircraft can be catastrophic. Interest in aircraft lightning protection has been stimulated by the introduction of advanced composites as an aircraft structural material. The present investigation has the objective to report experiences with three composite components which have flown in thunderstorms, taking into account three F-106B composite fin caps. The only visible lightning strike damage to a flame sprayed aluminum coated glass/epoxy fin cap was a small area of the aluminum which was burned. Visible lightning strike damage to a Kevlar/epoxy fin cap was limited to the exterior ply of aluminum coated glass fabric. In the case of a graphite/epoxy fin cap, lightning currents could be conducted.

Howell, W. E.↗

NASA NTRS1983

Organizing Space Shuttle parametric data for maintainability

A model of organization and management of Space Shuttle data is proposed. Shuttle avionics software is parametrically altered by a reconfiguration process for each flight. As the flight rate approaches an operational level, current methods of data management would become increasingly complex. An alternative method is introduced, using modularized standard data, and its implications for data collection, integration, validation, and reconfiguration processes are explored. Information modules are cataloged for later use, and may be combined in several levels for maintenance. For each flight, information modules can then be selected from the catalog at a high level. These concepts take advantage of the reusability of Space Shuttle information to reduce the cost of reconfiguration as flight experience increases.

Angier, R. C.↗

NASA NTRS1983

A simulator evaluation of an automatic terminal approach system

The automatic terminal approach system (ATAS) is a concept for improving the pilot/machine interface with cockpit automation. The ATAS can automatically fly a published instrument approach by using stored instrument approach data to automatically tune airplane avionics, control the airplane's autopilot, and display status information to the pilot. A piloted simulation study was conducted to determine the feasibility of an ATAS, determine pilot acceptance, and examine pilot/ATAS interaction. Seven instrument-rated pilots each flew four instrument approaches with a base-line heading select autopilot mode. The ATAS runs resulted in lower flight technical error, lower pilot workload, and fewer blunders than with the baseline autopilot. The ATAS status display enabled the pilots to maintain situational awareness during the automatic approaches. The system was well accepted by the pilots.

Hinton, D. A.↗

NASA NTRS1983

Single pilot scanning behavior in simulated instrument flight

Results from a simulation of general aviation instrument flight tasks in which the pilot's scan pattern and lookpoint were measured along with control inputs and state variables are given. The objective was to provide a baseline for comparing results from later studies of advanced avionics. Some of the scanning parameters measured are described, and conclusions from this and subsequent studies are presented.

Pennington, J. E.↗

NASA NTRS1983

Some thoughts concerning large load-carrying vehicles

Some implications relative to combat operations and force sustainability into the twenty-first century are discussed. The basic conjecture is that, sometime in the future, secure overseas basing may be denied to the United States by the Soviet Union or by unfriendly, unstable governments. In that event, the support of future battle itself, may be conducted from the continental U.S. and would introduce requirements for large, long-range, efficient, and sometimes, fast air vehicles. Some unusual design concepts and the technology requirements for such vehicles are suggested. It is concluded that, while much of the required technology is already being pursued, further advanced should be expected and sought in improved aerodynamics, propulsion, structures, and avionics with a view toward increased efficiency, utility, and affordability.

Spearman, M. L.↗

NASA NTRS1983

AFTI/F-16 flight test results and lessons

The advanced fighter technology integration (AFTI) F-16 aircraft is a highly complex digital flight control system integrated with advanced avionics and cockpit. The use of dissimilar backup modes if the primary system fails requires the designer to trade off system simplicity and capability. The tradeoff is evident in the AFTI/F-16 aircraft with its limited stability and fly by wire digital flight control systems when a generic software failure occurs the backup or normal mode must provide equivalent envelop protection during the transition to degraded flight control. The complexity of systems like the AFTI/F-16 system defines a second design issue, which is divided into two segments: (1) the effect on testing, (2) and the pilot's ability to act correctly in the limited time available for cockpit decisions. The large matrix of states possible with the AFTI/F-16 flight control system illustrates the difficulty of both testing the system and choosing real time pilot actions. The third generic issue is the possible reductions in the user's reliability expectations where false single channel information can be displayed at the pilot vehicle interface while the redundant set remains functional.

Ishmael, S. D.↗

NASA NTRS1983

A helicopter flight investigation of roll-control sensitivity, damping and cross coupling in a low altitude lateral maneuvering task

A helicopter in-flight simulation was conducted to determine the effects of variations in roll damping, roll sensitivity, and pitch and roll rate cross-coupling on helicopter flying qualities in a low altitude maneuver. The experiment utilized the UH-1H helicopter in-flight simulator, which is equipped with the V/STOLAND avionics system. The response envelope of this vehicle allowed simulation of configurations with low to moderate damping and sensitivity. A visual, low level slalom course was set up, consisting of constant speed and constant altitude S-turns around the 1000 ft makers of an 8000 ft runway. Results are shown in terms of Cooper-Harper pilot ratings, pilot commentary, and statistical and frequency analyses of the lateral characteristics. These results show good consistency with previous ground simulator results and are compared with existing flying qualities criteria.

Corliss, L. D.↗

NASA NTRS1983

Sensory redundancy management: The development of a design methodology for determining threshold values through a statistical analysis of sensor output data

Sensor redundancy management (SRM) requires a system which will detect failures and reconstruct avionics accordingly. A probability density function to determine false alarm rates, using an algorithmic approach was generated. Microcomputer software was developed which will print out tables of values for the cummulative probability of being in the domain of failure; system reliability; and false alarm probability, given a signal is in the domain of failure. The microcomputer software was applied to the sensor output data for various AFT1 F-16 flights and sensor parameters. Practical recommendations for further research were made.

Scalzo, F.↗

NASA NTRS1983

Path discrepancies between great circle and rhumb line

A mathematical model for a comparative analysis of great circle vs. rhumb line navigation in the continental United States has been developed at the Avionics Engineering Center, Ohio University. A FORTRAN simulation of the model has been implemented on the IBM 370 computer. The simulation predicts pertinent navigation information for the two flight paths. The basis for the project, which is a part of an M.S. thesis, is to provide a data base for computing discrepancies between the two flight paths. This document briefly describes the model and discusses the implications of the results obtained.

Kaul, R.↗

NASA NTRS1984

Thermal energy management process experiment

The thermal energy management processes experiment (TEMP) will demonstrate that through the use of two-phase flow technology, thermal systems can be significantly enhanced by increasing heat transport capabilities at reduced power consumption while operating within narrow temperature limits. It has been noted that such phenomena as excess fluid puddling, priming, stratification, and surface tension effects all tend to mask the performance of two-phase flow systems in a 1-g field. The flight experiment approach would be to attack the experiment to an appropriate mounting surface with a 15 to 20 meter effective length and provide a heat input and output station in the form of heaters and a radiator. Using environmental data, the size, location, and orientation of the experiment can be optimized. The approach would be to provide a self-contained panel and mount it to the STEP through a frame. A small electronics package would be developed to interface with the STEP avionics for command and data handling. During the flight, heaters on the evaporator will be exercised to determine performance. Flight data will be evaluated against the ground tests to determine any anomalous behavior.

Ollendorf, S.↗

NASA NTRS1983

Human factors issues associated with the use of speech technology in the cockpit

The human factors issues associated with the use of voice technology in the cockpit are summarized. The formulation of the LHX avionics suite is described and the allocation of tasks to voice in the cockpit is discussed. State-of-the-art speech recognition technology is reviewed. Finally, a questionnaire designed to tap pilot opinions concerning the allocation of tasks to voice input and output in the cockpit is presented. This questionnaire was designed to be administered to operational AH-1G Cobra gunship pilots. Half of the questionnaire deals specifically with the AH-1G cockpit and the types of tasks pilots would like to have performed by voice in this existing rotorcraft. The remaining portion of the questionnaire deals with an undefined rotorcraft of the future and is aimed at determining what types of tasks these pilots would like to have performed by voice technology if anything was possible, i.e. if there were no technological constraints.

Kersteen, Z. A.↗

NASA NTRS1984

AFTI/F-16 digital flight control system experience

The Advanced Flighter Technology Integration (AFTI) F-16 program is investigating the integration of emerging technologies into an advanced fighter aircraft. The three major technologies involved are the triplex digital flight control system; decoupled aircraft flight control; and integration of avionics, pilot displays, and flight control. In addition to investigating improvements in fighter performance, the AFTI/F-16 program provides a look at generic problems facing highly integrated, flight-crucial digital controls. An overview of the AFTI/F-16 systems is followed by a summary of flight test experience and recommendations.

Mackall, D. A.↗

NASA NTRS1977

Space Station Systems Analysis Study. Volume 2: Program review report

Major growth options for tended and manned space stations in LEO and GEO are examined including increased orbiter augmentation and habitation requirements. Approaches for providing power supplies, construction aids needed to assemble support platforms, transportation system constraints, and the hardware required for various missions categories are defined. Subsystem requirements are analyzed for structure; flight control; power generation and storage; avionic; life support systems; personnel provisions; and environmental control. Tradeoffs are considered.

Source record↗

NASA NTRS1984

A flight-test and simulation evaluation of the longitudinal final approach and landing performance of an automatic system for a light wing loading STOL aircraft equipped with wing spoilers

As part of a comprehensive flight-test investigation of short takeoff and landing (STOL) operating systems for the terminal systems for the terminal area, an automatic landing system has been developed and evaluated for a light wing-loading turboprop-powered aircraft. An advanced digital avionics system performed display, navigation, guidance, and control functions for the test aircraft. Control signals were generated in order to command powered actuators for all conventional controls and for a set of symmetrically driven wing spoilers. This report describes effects of the spoiler control on longitudinal autoland (automatic landing) performance. Flight-test results, with and without spoiler control, are presented and compared with available (basically, conventional takeoff and landing) performance criteria. These comparisons are augmented by results from a comprehensive simulation of the controlled aircraft that included representations of the microwave landing system navigation errors that were encountered in flight as well as expected variations in atmospheric turbulence and wind shear. Flight-test results show that the addition of spoiler control improves the touchdown performance of the automatic landing system. Spoilers improve longitudinal touchdown and landing pitch-attitude performance, particularly in tailwind conditions. Furthermore, simulation results indicate that performance would probably be satisfactory for a wider range of atmospheric disturbances than those encountered in flight. Flight results also indicate that the addition of spoiler control during the final approach does not result in any measurable change in glidepath track performance, and results in a very small deterioration in airspeed tracking. This difference contrasts with simulations results, which indicate some improvement in glidepath tracking and no appreciable change in airspeed tracking. The modeling problem in the simulation that contributed to this discrepancy with flight was not resolved.

Brown, S. C.↗

NASA NTRS1983

Graphics enhanced computer emulation for improved timing-race and fault tolerance control system analysis

A computer simulation system has been developed for the Space Shuttle's advanced Centaur liquid fuel booster rocket, in order to conduct systems safety verification and flight operations training. This simulation utility is designed to analyze functional system behavior by integrating control avionics with mechanical and fluid elements, and is able to emulate any system operation, from simple relay logic to complex VLSI components, with wire-by-wire detail. A novel graphics data entry system offers a pseudo-wire wrap data base that can be easily updated. Visual subsystem operations can be selected and displayed in color on a six-monitor graphics processor. System timing and fault verification analyses are conducted by injecting component fault modes and min/max timing delays, and then observing system operation through a red line monitor.

Szatkowski, G. P.↗

NASA NTRS1983

Unified analysis methods for a fault tolerant redundant strapdown inertial measurement unit

The use of a redundant strapdown inertial measurement unit (RSDIMU) has been considered as a source of sensor information for future aircraft. It is pointed out that failure detection and isolation (FDI) should be accomplished at the sensor level to ensure the accurate transfer of information to elements of the integrated avionics system. The present investigation is concerned with the impact of the FDI algorithm on system reliability and vice versa. A description is given of a technique to identify and assess critical areas of reliability requirements for the RSDIMU. Attention is given to the development of an FDI algorithm to meet these requirements.

Morrell, F. R.↗

NASA NTRS1983

The effects of cuing in time-shared tasks

The results of two divided-attention experiments involving the editing of route-way-point displays on an avionics computer unit are reported. Two side tasks were required of the subjects, and either no cue, verbal cues appearing on the CRT, or symbolic cues (lights on the keyboard adjacent to keys to be used) were given to facilitate the primary editing task. Forty female and 30 male undergraduates were trained in the separate and combined tasks and divided randomly into groups of 25 for the cuing tests. A second test with three 10-subject groups was conducted at least one month later to investigate the efficacy of cuing for infrequently used procedures. It is found that only symbolic cuing significantly improved primary-task performance, increasing editing accuracy in the repetitive tests and reducing editing time in the delayed tests. Verbal cuing, probably because it requires additional cognitive effort, has no significant beneficial effect. These results are considered important for designing instruments for work environments requiring the performance of concurrent tasks, and as aircraft cockpits.

Chechile, R. A.↗