Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “attenuator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Analysis of pressure spectra measurements in a ducted combustion system

Combustion noise propagation in an operating ducted liquid fuel combustion system is studied in relation to the development of combustion noise prediction and suppression techniques. The presence of combustor emissions in the duct is proposed as the primary mechanism producing the attenuation and dispersion of combustion noise propagating in an operating liquid fuel combustion system. First, a complex mathematical model for calculating attenuation and dispersion taking into account mass transfer, heat transfer, and viscosity effects due to the presence of liquid fuel droplets or solid soot particles is discussed. Next, a simpler single parameter model for calculating pressure auto-spectra and cross-spectra which takes into account dispersion and attenuation due to heat transfer between solid soot particles and air is developed. Then, auto-spectra and cross-spectra obtained from internal pressure measurements in a combustion system consisting of a J-47 combustor can, a spool piece, and a long duct are presented. Last, analytical results obtained with the single parameter model are compared with the experimental measurements. The single parameter model results are shown to be in excellent agreement with the measurements.

Miles, J. H.↗
NASA NTRS1981

Laboratory measurements of selected optical, physical, chemical, and remote-sensing properties of five water mixtures containing Calvert clay and a nonfluorescing dye

Total suspended solids concentrations ranged from 6.1 ppm to 24.3 ppm and sizes ranged between 1.5 micrometers and 10 micrometers with the most frequently occurring size less than 2 micrometers. Iron concentration was less than 1 percent of the total suspended solids. Nonfluorescing dye concentrations of the two mixtures were 20 ppm and 40 ppm. Attenuation coefficient for the five mixtures ranged from 4.8/m to 21.3/m. Variations in volume scattering function with phase angle were typical. Variations in attenuation and absorption coefficient with wavelength were similar for the mixtures without the dye. Attenuation coefficient of the mixtures with the dye increased for wavelengths less than 600 nm due to the dye's strong absorption peak near 500 nm. Reflectance increased as the concentration of Calvert clay increased and peaked near 600 nm. The nonfluorescent dye decreased the magnitude of the peak, but had practically no effect on the variation for wavelengths greater than 640 nm. At wavelengths less than 600 nm, the spectral variations of the mixtures with the dye were significantly different from those mixtures without the dye.

Usry, J. W.↗
NASA NTRS1980

Snow Electromagnetic Measurements

An electromagnetic system is described for measuring the dielectric constant and attenuation of snow samples in the frequency range of 4 to 12 GHz. System components consists of a swept-frequency source, microwave horns, network analyzer, and XY plotter. The procedure for calibrating the effect of wetness on the snow properties is described. Equations are given that express the experimentally determined relation between attenuation per unit length and volume percent wetness at any frequency between 4 and 12 GHz. permittivity can be calculated from the snow density, attenuation per unit length, and frequency. Some applications of the techniques are described such as runoff forecasting from mountain snowpacks.

Linlor, W. I.↗
NASA NTRS1981

Ground effects on aircraft noise for a wide-body commercial airplane

Ground effects on noise from a high-bypass ratio engined aircraft are investigated. A 747 is flown at altitudes from 30 to 960 m past a 20-microphone array, and ground effects are calculated from noise measurements as a function of elevation angle and slant range. Results are given in terms of EPNL units and are compared with previous results of a turbojet-powered T-38 and SAE-recommended empirical lateral attenuation prediction procedures. Theoretical predictions are made based on a method developed by Pao et al. (1978) and are compared with both 747 and T-38 results, demonstrating good agreement although a consistent underprediction of peak measured attenuation is observed. Measured ground effects are found largest at 200 Hz, and no definite shielding differences are apparent for a directivity angle of 122.5 deg. Less lateral attenuation of effective perceived noise is measured for both aircraft and is attributed to the dominance of low-frequency noise in the source spectrum.

Willshire, W. L., Jr.↗
NASA NTRS1979

Handbook for the estimation of microwave propagation effects: Link calculations for earth-space paths (path loss and noise estimation)

A single model for a standard of comparison for other models when dealing with rain attenuation problems in system design and experimentation is proposed. Refinements to the Global Rain Production Model are incorporated. Path loss and noise estimation procedures as the basic input to systems design for earth-to-space microwave links operating at frequencies from 1 to 300 GHz are provided. Topics covered include gaseous absorption, attenuation by rain, ionospheric and tropospheric scintillation, low elevation angle effects, radome attenuation, diversity schemes, link calculation, and receiver noise emission by atmospheric gases, rain, and antenna contributions.

Crane, R. K.↗
NASA NTRS1981

Laboratory measurements of physical, chemical, and optical characteristics of Lake Chicot sediment waters

Reflectance, chromaticity, diffuse attenuation, beam attenuation, and several other physical and chemical properties were measured for various water mixtures of lake bottom sediment. Mixture concentrations range from 5 ppm to 700 ppm by weight of total suspended solids in filtered deionized tap water. Upwelled reflectance is a nonlinear function of remote sensing wave lengths. Near-infrared wavelengths are useful for monitoring highly turbid waters with sediment concentrations above 100 ppm. It is found that both visible and near infrared wavelengths, beam attenuation correlates well with total suspended solids ranging over two orders of magnitude.

Witte, W. G.↗
NASA NTRS1982

Ultrasonic and mechanical characterizations of fatigue states of graphite epoxy composite laminates

Eight-ply (0, + or - 45, 0)s laminates of Hercules AS/3501-6 graphite epoxy composite are fabricated using various cure pressures ranging from 0.52 to 0.86 MPa and cure temperatures ranging from 150 C to 200 C. In general, the minimum composite void volume fraction is obtained at a cure temperature of 175 C and a cure pressure of 0.86 MPa, or at 200 C and 0.86 MPa. The ultrasonic attenuation at 4 MHz was found to correlate with the composite void volume fraction. Composite specimens were tested in flexural fatigue. Beyond 10,000 fatigue cycles, the ultrasonic attenuation at 4 MHz was found to increase and the flexural stiffness was found to decrease. The ultrasonic attenuation at 4 MHz of the as-fabricated composite can be correlated with the number of fatigue cycles to failure.

Williams, J. H., Jr.↗
NASA NTRS1981

Harmonic and Anharmonic Properties of Diamond Structure Crystals with Application to the Calculation of the Thermal Expansion of Silicon

Silicon has interesting harmonic and anharmonic properties such as the low lying transverse acoustic modes at the X and L points of the Brillouin zone, negative Gruneisen parameters, negative thermal expansion and anomalous acoustic attenuation. In an attempt to understand these properties, a lattice dynamical model employing long range, nonlocal, dipole-dipole interactions was developed. Analytic expression for the Gruneisen parameters of several modes are presented. These expressions explain how the negative Gruneisen parameters arise. This model is applied to the calculation of the thermal expansion of silicon from 5K to 1700K. The thermoelastic contribution to the acoustic attenuation of silicon is computed from 1 to 300 K. Strong attenuation anomalies associated with negative thermal expansion are found in the vicinity of 17K and 125K.

Wanser, K. H.↗
NASA NTRS1983

Pair production in superstrong magnetic fields

The production of electron-positron pairs by single photons in magnetic fields 10 to the twelth power G was investigated in detail for photon energies near threshold as well as for the asymptotic limit of high photon energy. The exact attenuation coefficient, which is derived and then evaluated numerically, is strongly influenced by the discrete energy states of the electron and positron. Near threshold, it exhibits a sawtooth pattern as a function of photon energy, and its value is significantly below that predicted by the asymptotic expression for the attenuation coefficient. The energy distributions of the created pair are computed numerically near threshold and analytic expressions are derived in the asymptotic limit. These results indicate that as field strength and photon energy increase, it becomes increasingly probable for the pair to divide the photon energy unequally. This effect, as well as the threshold behavior of the attenuation coefficient, could have important consequences for pulsar models.

Daugherty, J. K.↗
NASA NTRS1983

The effect of stress on ultrasonic pulses in fiber reinforced composites

An acoustical-ultrasonic technique was used to demonstrate relationships existing between changes in attenuation of stress waves and tensile stress for an eight ply 0 degree graphite-epoxy fiber reinforced composite. All tests were conducted in the linear range of the material for which no mechanical or macroscopic damage was evident. Changes in attenuation were measured as a function of tensile stress in the frequency domain and in the time domain. Stress wave propagation in these specimens was dispersive, i.e., the wave speed depends on frequency. Wave speeds varied from 267 400 cm/sec to 680 000 cm/sec as the frequency of the signal was varied from 150 kHz to 1.9 MHz which strongly suggests that flexural/lamb wave modes of propagation exist. The magnitude of the attenuation changes depended strongly on tensile stress. It was further observed that the wave speeds increased slightly for all tested frequencies as the stress was increased.

Hemann, J. H.↗
NASA NTRS1983

Passive remote sensing of ocean optical propagation parameters

A method is described for producing a global data of ocean optical properties through the exploitation of optical remote sensing techniques. The diffuse attenuation, K, and the radiance reflectance factor R sub L, of the ocean surface waters can be derived from the radiance data provided by the Coastal Zone Color Scanner and compiled into a computer based atlas of these properties. While these remotely sensed values can only be directly related to the water properties in the first or upper attenuation length, extensive in water measurements have demonstrated that a useful correlation exists between the K that applies to the upper attenuation length, for example, and the mean K over the upper 100 or 200 meters of the ocean. Such an empirical finding greatly enhances the usefulness of this remotely sensed propagation parameter. Examples of the type of information being produced and archived for the atlas are presented.

Austin, R. W.↗
NASA NTRS1984

Numerical methods for analyzing electromagnetic scattering

The wave attenuation in a cylindrical waveguide coated with lossy dielectric material was studied. The scope was extended to the high frequency case for calculating attenuation coefficients and propagation constants of a dielectric coated circular waveguide. The magnetic material coating was studied. At low frequency a one way 3dB attenuation was achieved within a longitudinal distance of one diameter. A software program was generated to plot the field patterns of the lowest 30 modes in the cylindrical waveguides.

Lee, S. W.↗
NASA NTRS1983

Pair production in superstrong magnetic fields

The production of electron-positron pairs by single photons in magnetic fields of not less than about 10 to the 12th gauss has been investigated in detail for photon energy. The exact attenuation coefficient, which is derived and then evaluated numerically, is strongly influenced by the discrete energy states of the electron and positron. Near threshold, it exhibits a 'sawtooth' pattern as a function of photon energy and its value is significantly below that predicted by the asymptotic expression for the attenuation coefficient. The energy distributions of the created pair are computed numerically near threshold, and analytic expressions are derived in the asymptotic limit. These results indicate that as field strength and photon energy increase, it becomes increasingly probable for the pair to divide strength energy unequally. This effect, as well as the threshold behavior of the attenuation coefficient, could have important consequences to pulsar models.

Daugherty, J. K.↗
NASA NTRS1985

Numerical methods for analyzing electromagnetic scattering

Numerical methods to analyze electromagnetic scattering are presented. The dispersions and attenuations of the normal modes in a circular waveguide coated with lossy material were completely analyzed. The radar cross section (RCS) from a circular waveguide coated with lossy material was calculated. The following is observed: (1) the interior irradiation contributes to the RCS much more than does the rim diffraction; (2) at low frequency, the RCS from the circular waveguide terminated by a perfect electric conductor (PEC) can be reduced more than 13 dB down with a coating thickness less than 1% of the radius using the best lossy material available in a 6 radius-long cylinder; (3) at high frequency, a modal separation between the highly attenuated and the lowly attenuated modes is evident if the coating material is too lossy, however, a large RCS reduction can be achieved for a small incident angle with a thin layer of coating. It is found that the waveguide coated with a lossy magnetic material can be used as a substitute for a corrugated waveguide to produce a circularly polarized radiation yield.

Lee, S. W.↗
NASA NTRS1985

Sound propagation studies for a large horizontal axis wind turbine

Systematic noise measurements in three directions with respect to the wind vector, over a range of distances to 1050 m, over a range of frequencies from 8 Hz to 2000 Hz, and for a stable wind turbine noise source (WTS-4) in windy conditions (V = 9.4 to 13.0 m/s) are presented. At frequencies above 63 Hz in the downwind and crosswind directions the sound pressure levels decay with distance according to predictions based on atmospheric absorption and spherical spreading, assuming no excess attenuation due to ground effects. In the upwind direction there is excess attenuation due to an acoustic shadow zone. The assumption of a distributed noise source leads to better noise estimates in the upwind direction. For very low frequencies 8 to 16 Hz no excess attenuation was observed in the upwind direction at distances up to 1050 m and a sound pressure level decay rate of approximately 3 dB per doubling of distance was observed in the downwind direction.

Shepherd, K. P.↗
NASA NTRS1984

Modeling the backscattering and transmission properties of vegetation canopies

Experimental measurements of canopy attenuation at 10.2 GHz (X-band) for canopies of wheat and soybeans, experimental observations of the effect upon the microwave backscattering coefficient (sigma) of free water in a vegetation canopy, and experimental measurements of sigma (10.2 GHz, 50 deg, VV and VH polarization) of 30 agricultural fields over the growing season of each crop are discussed. The measurements of the canopy attenuation through wheat independently determined the attenuation resulting from the wheat heads and that from the stalks. An experiment conducted to simulate the effects of rain or dew on sigma showed that sigma increases by about 3 dB as a result of spraying a vegetation canopy with water. The temporal observations of sigma for the 30 agricultural fields (10 each of wheat, corn, and soybeans) indicated fields of the same crop type exhibits similar temporal patterns. Models previously reported were tested using these multitemporal sigma data, and a new model for each crop type was developed and tested. The new models proved to be superior to the previous ones.

Allen, C. T.↗
NASA NTRS1985

Numerical methods for analyzing electromagnetic scattering

Attenuation properties of the normal modes in an overmoded waveguide coated with a lossy material were analyzed. It is found that the low-order modes, can be significantly attenuated even with a thin layer of coating if the coating material is not too lossy. A thinner layer of coating is required for large attenuation of the low-order modes if the coating material is magnetic rather than dielectric. The Radar Cross Section (RCS) from an uncoated circular guide terminated by a perfect electric conductor was calculated and compared with available experimental data. It is confirmed that the interior irradiation contributes to the RCS. The equivalent-current method based on the geometrical theory of diffraction (GTD) was chosen for the calculation of the contribution from the rim diffraction. The RCS reduction from a coated circular guide terminated by a PEC are planned schemes for the experiments are included. The waveguide coated with a lossy magnetic material is suggested as a substitute for the corrugated waveguide.

Lee, S. W.↗
NASA NTRS1986

Ultrasonic measurement of porosity in casts and welds

The development of a quantitative nondestructive method which involves ultrasonic attenuation measurements in frequency domain to determine volume fraction of porosity in aluminum cast is discussed. The aluminum alloy A357 casting samples were produced at the Ohio State University Foundry with controlled porosity contents ranging from 0% to 6%. A computer controlled system was used to direct ultrasonic beam to a test sample to different places to conduct ultrasonic attenuation measurements. The plot of attenuation coefficients as a function of frequency was then evaluated based on existing theories to determine volume fraction of porosity and pore size.

Adler, L.↗