Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “attack modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

F-15 rotary balance data for an angle-of-attack range of 8 deg to 90 deg

Aerodynamic characteristics obtained in a rotational flow environment, utilizing a rotary balance are presented in plotted form for a 1/12 scale F-15 airplane model. The configurations tested included the buildup of airplane components and the basic airplane with various control deflections. Data are presented for all configurations without analysis for an angle of attack range of 8 to 90 deg, and clockwise and counterclockwise rotations covering an omega b/2V range from 0 to 0.4. Selected configurations are presented over an extended omega b/2V range from 0 to 0.9.

Barnhart, B.↗
NASA NTRS1961

Investigation at High Subsonic Speeds of the Use of Low Auxiliary Tail Surfaces having Dihedral to Improve the Longitudinal and Directional Stability of a T-Tail Model at High Lift

An investigation of the use of low auxiliary horizontal-tail surfaces to alleviate the pitch-up tendency at high lift of an airplane configuration having a T - tail has been conducted in the Langley high-speed 7- by 10-foot tunnel. The basic model had a wing with an aspect ratio of 3, a taper ratio of 0.143, and an unswept 80-percent chord line. The Mach number for most of the tests extended from 0.60 to 0.94 and the angle-of-attack range was from -2 deg. to approximately 24 deg. at the lowest test Mach number. A preliminary study of a systematic series of auxiliary tails indicated that the pitch-up tendency at high lift encountered on the basic model could be greatly alleviated by use of a relatively small, very low-aspect-ratio auxiliary horizontal tail. This tail was located radially with respect to the fuselage center line with 30 deg. negative dihedral and therefore provided a significant favorable increment to directional stability of the model throughout most of the test angle-of-attack range.

Sleeman, William C., Jr.↗
NASA NTRS1982

V/STOL Tandem Fan transition section model test

An approximately 0.25 scale model of the transition section of a tandem fan variable cycle engine nacelle was tested in the NASA Lewis Research Center 10-by-10 foot wind tunnel. Two 12-inch, tip-turbine driven fans were used to simulate a tandem fan engine. Three testing modes simulated a V/STOL tandem fan airplane. Parallel mode has two separate propulsion streams for maximum low speed performance. A front inlet, fan, and downward vectorable nozzle forms one stream. An auxilliary top inlet provides air to the aft fan - supplying the core engine and aft vectorable nozzle. Front nozzle and top inlet closure, and removal of a blocker door separating the two streams configures the tandem fan for series mode operations as a typical aircraft propulsion system. Transition mode operation is formed by intermediate settings of the front nozzle, blocker door, and top inlet. Emphasis was on the total pressure recovery and flow distortion at the aft fan face. A range of fan flow rates were tested at tunnel airspeeds from 0 to 240 knots, and angles-of-attack from -10 to 40 deg for all three modes. In addition to the model variables for the three modes, model variants of the top inlet were tested in the parallel mode only. These lip variables were: aft lip boundary layer bleed holes, and Three position turning vane. Also a bellmouth extension of the top inlet side lips was tested in parallel mode.

Simpkin, W. E.↗
NASA NTRS1975

Results of an investigation of hypersonic viscous interaction effects on and 0.01 scale Space Shuttle Orbiter 51-0 model in the AEDC-VKF Hypervelocity Wind Tunnel (0A81)

The major hypersonic aerodynamic results obtained experimentally from the 0.010-scale (51-0) 140A/B orbiter vehicle are presented. The test was conducted over an angle-of-attack range from 20 to 35 degrees for nominal Mach numbers of 16 and 20. The Mach 16 data were obtained at Reynolds numbers, based on model length, of nominally 0.54 x 106 and 1.18 x 106. The Mach number 20 data were obtained at nominal Reynolds numbers of 0.08 x 106 and 0.27 x 106. Various elevon deflections and body flap deflections were tested for determination of control effectiveness. The test objectives were: (1) verify December 1973 aerodynamic Design Data Book estimates for Mach number greater than 10; (2) determine configuration forward and aft trim boundaries and control characteristics; (3) determine high Mach number - low Reynolds number effects; (4) determine if positive control surface flow separation is present and magnitude of separation effects.

Elder, D. J.↗
NASA NTRS1992

Thrust vectoring characteristics of the F-18 high alpha research vehicle at angles of attack from 0 to 70 deg

An investigation was conducted to determine the multiaxis thrust-vectoring characteristics of the F-18 High Alpha Research Vehicle (HARV). A 0.10-scale model was modified with hardware to simulate the three-vane thrust vectoring system of the F-18/HARV. This investigation was conducted at Mach numbers ranging from 0.30 to 0.70, at angles of attack from 0 to 70 deg, and nozzle-pressure ratios from 2.0 to approximately 5.0. Results indicate that the thrust vectoring system of F-18/HARV can successfully generate multiaxis thrust vectoring. During vectoring, resultant thrust-vector angles were always less than the corresponding geometric vane deflection angle and were accompanied by large thrust losses.

Asbury, Scott C.↗
NASA NTRS1984

Low speed rotary aerodynamics of F-18 configuration for 0 deg to 90 deg angle of attack: Test results and analysis

Aerodynamic characteristics obtained in a rotational flow environment, utilizing a rotary balance located in the Langley Spin Tunnel, are discussed and presented in tabular form for a 1/10 scale F-18 airplane model. The rotational aerodynamic characteristics were established for the basic airplane, as well as the influence of control deflections and the contribution of airplane components, i.e., body, wing, leading edge extension, horizontal and vertical tails, on these characteristics up to 90 deg angle of attack. Spin equilibrium conditions predicted using the measured data are also presented and compared with spin model and full scale flight results.

Hultberg, R.↗
NASA NTRS1972

Effects of body shape on the aerodynamic characteristics of an all-body hypersonic aircraft configuration at Mach numbers from 0.65 to 10.6

An experimental investigation was conducted to determine the effects of several variations in body shape on the aerodynamic characteristics of an all-body hypersonic aircraft configuration. The basic configuration had a delta planform with an elliptic cone forebody and an afterbody of elliptic cross section terminating in a straight-line trailing edge. Variations in body shape included the ratio of maximum cross-sectional to body planform area, body leading-edge sweep, and forebody length ratio. In addition, the effects of a thin wing mounted on one of the bodies was investigated, and the aerodynamic characteristics of just the forebodies of two of the configurations were determined. The models had no stabilizing surfaces or propulsion system packages. Ranges of angle of attack (-4 deg to +15 deg) and angle of sideslip (-4 deg to +8 deg) were investigated. Of the four complete bodies, the configuration with the lowest ratio of cross-sectional to body planform area had the highest maximum lift-drag ratio and the greatest level of longitudinal stability at most Mach numbers. All the configurations had positive longitudinal stability near maximum lift-drag ratio at most Mach numbers. With exception of the lowest subsonic Mach numbers, changes in body sweep angle and in forebody length ratio had only minor effects on maximum lift-drag ratio.

Nelms, W. P., Jr.↗
NASA NTRS1972

Summary of directional divergence characteristics of several high performance aircraft configurations

The present paper summarizes the high-angle-of-attack characteristics of a number of high-performance aircraft as determined from model force tests and free-flight model tests and correlates these characteristics with the dynamic directional-stability parameter. This correlation shows that the dynamic directional-stability parameter correlates fairly well with directional divergence. Data are also presented to show the effect of some airframe modifications on the directional divergence potential of the configuration. These results show that leading-edge slates seem to be the most effective airframe modification for reducing or eliminating the directional divergence potential of aircraft with moderately swept wings.

Greer, H. D.↗
NASA NTRS1973

Effects of fineness and closure ratios on boattail drag of circular-arc-afterbody models with jet exhaust at Mach numbers up to 1.3

The effects of variations in fineness ratio and closure ratio on the boattail drag of circular-arc afterbody models were investigated at static conditions and at Mach numbers from 0.40 to 1.30. Jet total-pressure ratio was varied from jet off to about 6, depending on Mach number. Reynolds number based on model maximum diameter varied from about 1.2 million to 2.18 million. Angle of attack was varied from -4 deg to 8 deg. The results indicate that, at subsonic speeds before the drag rise and at a scheduled pressure ratio, the total drag (pressure plus calculated skin friction) is approximately equal for configurations with the same closure ratio. Also, for configurations with the same closure ratio, increasing fineness ratio results in an increased drag-rise Mach number; and for configurations with the same fineness ratio, increasing closure ratio results in an increased drag-rise Mach number.

Reubush, D. E.↗
NASA NTRS1974

Continued investigations in the NAAL low speed wind tunnel into the effects of the air breathing propulsion system on orbiter subsonic stability and control characteristics (OA62A)

Experimental aerodynamic investigations were conducted on a stingmounted 0.0405-scale representation (model 43-0) of the 140A/B Space Shuttle Orbiter in a Low Speed Wind Tunnel. The NASA designation for this test was 0A62A. The primary test objective was to continue studies, initiated on tests 0A16 and 0A71A and 0A71C, in optimizing the air breathing propulsion system (ABPS) and investigating the aerodynamic effects of various nacelle number/location configurations on the orbiter stability and control characteristics. Orbiter stability and control characteristics, both with and without ABPS, were investigated at elevon deflections of 0, + or -5, + or -19, + or -5, and -20 deg; aileron deflections of 0 and 10 deg (about 0 deg elevon); and rudder deflections of 0, -7.5, and -15 deg. Aerodynamic force and moment data was measured in the body axis system by a 2.5-inch task type internal balance. The model was sting supported through the base region with a nominal angle of attack range of -4 to 30 deg. Yaw polars were recorded over the beta range of -10 to 10 deg at fixed angles of attack of 0, 5, 10, and 15 deg.

Mennell, R.↗
NASA NTRS1975

Aerodynamic damping and oscillatory stability in pitch of a model of a proposed manned lifting entry vehicle at Mach Numbers of 1.80, 2.16, and 2.86

Wind tunnel tests were conducted using a model of a proposed manned lifting entry vehicle to determine the aerodynamic damping and oscillatory stability in pitch. The model was tested at Mach numbers of 1.80, 2.16, and 2.86. Angles of attack varied from minus 2 degrees to plus 30 degrees at zero angle of sideslip using a small-amplitude, forced-oscillation technique. It was determined that, in general, all the configurations have near zero or slightly positive damping in pitch throughout the angle of attack range. The effects of the deflection of flaps on aerodynamic damping are discussed.

Kilgore, R. A.↗
NASA NTRS1976

Results of an investigation of jet plume effects on an 0.010-scale model (75-OTS) of the space shuttle integrated vehicle in the 9 x 7-foot leg of the NASA/Ames unitary wind tunnel (IA82B), volume 1

The base pressure environment was investigated for the first and second stage mated vehicle in a supersonic flow field from Mach 1.55 through 2.20 with simulated rocket engine exhaust plumes. The pressure environment was investigated for the orbiter at various vent port locations at these same freestream conditions. The Mach number environment around the base of the model with rocket plumes simulated was examined. Data were obtained at angles of attack from -4 deg through +4 deg at zero yaw, and at yaw angles from -4 deg through +4 deg at zero angle of attack, with rocket plume sizes varying from smaller than nominal to much greater than nominal. Failed orbiter engine data were also obtained. Elevon hinge moments and wing panel load data were obtained during all runs. Photographs of the tested configurations are shown.

Hawthorne, P. J.↗
NASA NTRS1977

Low-speed wind tunnel investigation of an advanced supersonic cruise arrow-wing configuration

A preliminary assessment of possible means for improving the low speed aerodynamic characteristics of advanced supersonic cruise arrow wing configurations and to extend the existing data base of such configurations has been made. Principle configuration variables included wing-leading and trailing-edge flap deflection, fuselage nose strakes, and engine exhaust nozzle deflection. Results showed that deflecting the wing leading edge apex flaps downward provided improved longitudinal stability but resulted in reduced directional stability. The model exhibited relatively low values of directional stability over the operational angle of attack range and experienced large asymmetric yawing moments at high angles of attack. The use of nose strakes was found to be effective in increasing the directional stability and eliminating the asymmetric yawing moment.

Coe, P. L., Jr.↗
NASA NTRS1978

Aerodynamic characteristics at Mach 6 of a wing-body concept for a hypersonic research airplane

The static aerodynamic characteristics of a 1/30 scale model of a wing-body concept for a high speed research airplane were investigated in the Langley 20 inch Mach six tunnel. The investigation consisted of configuration buildup from the basic body by adding a wing, center vertical tail, three-module scramjet, and six-module scramjet engine. The test Mach number was six at a Reynolds number, based on model fuselage length, of about 13,700,000. The test angle-of-attack range was 4 to 20 D at constant angles of sideslip of 0, 2, and 4 deg. The elevons were deflected from 10 to -15 D for pitch control. Roll and yaw control were investigated. Experimental aerodynamic characteristics are compared with analytical elements.

Dillon, J. L.↗
NASA NTRS1979

Subsonic wind-tunnel investigation of leading-edge devices on delta wings (data report)

The drag reduction potential of leading edge devices on delta wings at high lift is presented. Fences, pylon type vortex generators, chordwise slots, and sharp plate extensions were tested on wing models with 60 and 74 degree swept blunt leading edges at angles of attack to 32 degrees. Six component balance and leading edge surface pressure measurements were taken with various geometry and spanwise arrangements of the devices. Tables listing the data, without analysis, are presented.

Dhanvada, M. R.↗
NASA NTRS1986

Euler calculations for rotor configurations in unsteady forward flight

A solution procedure is presented for the lifting transonic flow past modern rotor configurations in forward flight. In this procedure, the three-dimensional, unsteady Euler equations are solved in strong conservation form on a body-fitted moving coordinate system. A hybrid procedure of second order spatial accuracy and first order temporal accuracy is used to integrate the governing equations. In lifting flows, the effect of the elements of wake not captured by the computational procedure, and other aeroelastic effects are accounted for as local angle of attack corrections. Detailed comparisons with experimental data are presented for a 1/7 scale model of the Cobra OLS rotor, and for a three-bladed rotor tested in France. Some preliminary results are also presented for a three-dimensional blade vortex interaction problem.

Sankar, L. N.↗
NASA NTRS1987

Effects of the installation and operation of jet-exhaust yaw vanes on the longitudinal and lateral-directional characteristics of the F-14 airplane

A wind tunnel investigation was conducted in the Langley 16-Foot Transonic Tunnel to determine the effects of the installation and use of jet exhaust yaw vanes on the longitudinal and lateral-directional characteristics of the F-14 aircraft. The model was tested at Mach numbers from 0.70 to 1.25 at angles of attack from 0 deg to 4.3 deg. Compressed air was used to simulate nozzle exhaust flow from jet off up to a nozzle pressure ratio of 8. The results of the investigation show that the yaw vanes can augment the rudders to provide directional control, but further investigation will be necessary to optimize the deflection schedule associated with the various nozzle power settings.

Reubush, David E.↗
NASA NTRS1986

PAN AIR analysis of the NASA/MCAIR 279-3: An advanced supersonic V/STOL fighter/attack aircraft

PAN AIR is a computer program for predicting subsonic or supersonic linear potential flow about arbitrary configurations. The program was applied to a highly complex single-engine-cruise V/STOL fighter/attack aircraft. Complexities include a close-coupled canard/wing, large inlets, and four exhaust nozzles mounted directly under the wing and against the fuselage. Modeling uncertainties involving canard wake location and flow-through approximation through the inlet and the exhaust nozzles were investigated. The recently added streamline capability of the program was utilized to evaluate visually the predicted flow over the model. PAN AIR results for Mach numbers of 0.6, 0.9, and angles of attack of 0, 5, and 10 deg. were compared with data obtained in the Ames 11- by 11-Foot Transonic Wind tunnel, at a Reynolds number of 3.69 x 10 to the 6th power based on c bar.

Madson, Michael D.↗