Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “analytical”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Assessing the sensitivity and repeatability of permanganate oxidizable carbon as a soil health metric: An interlab comparison across soils

Soil organic matter is central to the soil health framework. Therefore, reliable indicators of Soil organic matter is central to the soil health framework. Therefore, reliable indicators of changes in soil organic matter are essential to inform land management decisions. Permanganate oxidizable carbon (PDXC), an emerging soil health indicator, has shown promise for being sensitive to soil management. However, strict standardization is required for widespread implementation in research and commercial contexts. Here, we used 36 soils-three from each of the 12 USDA soil orders-to determine the effects of sieve size and soil mass of analysis on PDXC results. Using replicated measurements across 12 labs in the US and the EU (n = 7951 samples), we quantified the relative importance of 1) variation between labs, 2) variation within labs, 3) effect soil mass, and 4) effect of soil sieve size on the repeatability of PDXC. We found a wide range of overall variability in PDXC values across labs (0.03 to 171.8%; mean = 13.4%), and much of this variability was attributable to within-lab variation (median = 6.5%) independently of soil mass or sieve size. Greater soil mass (2.5 g) decreased absolute PDXC values by a mean of 177 mg kg -1 soil and decreased analytical variability by 6.5%. For soils with organic carbon (SOC) >10%, greater soil mass (2.5 g) resulted in more frequent PDXC values above the limit of detection whereas the lower soil mass (0.75 g) resulted in PDXC values below the limit of detection for SOC contents <5%. A finer sieve size increased absolute values of PDXC by 124 mg kg -1 while decreasing the analytical variability by 1.8%. In general, soils with greater SOC contents had lower analytical variability. These results point to potential standardizations of the PDXC protocol that can decrease the variability of the metric. We recommend that the PDXC protocol be standardized to use 2.5 g for soils <10% SOC. Sieve size was a relatively small contributor to analytical variability and therefore we recommend that this decision be tailored to the study purpose. Tradeoffs associated with these standardizations can be mitigated, ultimately providing guidance on how to standardize PDXC for routine analysis.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Nonlinear sparse Bayesian learning for physics-based models

This paper addresses the issue of overfitting while calibrating unknown parameters of over-parameterized physics-based models with noisy and incomplete observations. Here, a semi-analytical Bayesian framework of nonlinear sparse Bayesian learning (NSBL) is proposed to identify sparsity among model parameters during Bayesian inversion. NSBL offers significant advantages over machine learning algorithm of sparse Bayesian learning (SBL) for physics-based models, such as 1) the likelihood function or the posterior parameter distribution is not required to be Gaussian, and 2) prior parameter knowledge is incorporated into sparse learning (i.e. not all parameters are treated as questionable). NSBL employs the concept of automatic relevance determination (ARD) to facilitate sparsity among questionable parameters through parameterized prior distributions. The analytical tractability of NSBL is enabled by employing Gaussian ARD priors and by building a Gaussian mixture-model approximation of the posterior parameter distribution that excludes the contribution of ARD priors. Subsequently, type-II maximum likelihood is executed using Newton's method whereby the evidence and its gradient and Hessian information are computed in a semi-analytical fashion. We show numerically and analytically that SBL is a special case of NSBL for linear regression models. Subsequently, a linear regression example involving multimodality in both parameter posterior pdf and model evidence is considered to demonstrate the performance of NSBL in cases where SBL is inapplicable. Next, NSBL is applied to identify sparsity among the damping coefficients of a mass-spring-damper model of a shear building frame. These numerical studies demonstrate the robustness and efficiency of NSBL in alleviating overfitting during Bayesian inversion of nonlinear physics-based models.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Accurately simulating nine-dimensional phase space of relativistic particles in strong fields

Next-generation high-power laser systems that can be focused to ultra-high intensities exceeding 10 23 W/cm 2 are enabling new physics regimes and applications. The physics of how these lasers interact with matter is highly nonlinear, relativistic, and can involve lowest-order quantum effects. The current tool of choice for modeling these interactions is the particle-in-cell (PIC) method. In the presence of strong electromagnetic fields, the motion of charged particles and their spin is affected by radiation reaction (either the semi-classical or the quantum limit). Standard (PIC) codes usually use Boris or similar operator-splitting methods to advance the particles in standard phase space. These methods have been shown to require very small time steps in the strong-field regime in order to obtain accurate results. In addition, some problems require tracking the spin of particles, which creates a nine-dimensional (9D) particle phase space, i.e., (x, u, s). Therefore, numerical algorithms that enable high-fidelity modeling of the 9D phase space in the strong-field regime (where both the spin and momentum evolution are affected by radiation reaction) are desired. Here we present a new particle pusher that works in 9D and 6D phase space (i.e., with and without spin) based on analytical rather than leapfrog solutions to the momentum and spin advance from the Lorentz force, together with the semi-classical form of radiation reaction in the Landau-Lifshitz equation and spin evolution given by the Bargmann-Michel-Telegdi equation. Analytical solutions for the position advance are also obtained, but these are not amenable to the staggering of space and time in standard PIC codes. These analytical solutions are obtained by assuming a locally uniform and constant electromagnetic field during a time step. The solutions provide the 9D phase space advance in terms of a particle's proper time, and a mapping is used to determine the proper time step duration for each particle as a function of the lab frame time step. Due to the analytical integration of particle trajectory and spin orbit, the constraint on the time step needed to resolve trajectories in ultra-high fields can be greatly reduced. The time step required in a PIC code for accurately advancing the fields may provide additional constraints. We present single-particle simulations to show that the proposed particle pusher can greatly improve the accuracy of particle trajectories in 6D or 9D phase space for given laser fields. We have implemented the new pusher into the PIC code Osiris. Example simulations show that the proposed pusher provides improvement for a given time step. A discussion on the numerical efficiency of the proposed pusher is also provided.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2021

PARIS: Predicting application resilience using machine learning

The traditional method to study application resilience to errors in HPC applications uses fault injection (FI), a time-consuming approach. Furthermore, while analytical models have been built to overcome the inefficiencies of FI, they lack accuracy. In this paper, we present PARIS, a machine-learning method to predict application resilience that avoids the time-consuming process of random FI and provides higher prediction accuracy than analytical models. PARIS captures the implicit relationship between application characteristics and application resilience, which is difficult to capture using most analytical models. We overcome many technical challenges for feature construction, extraction, and selection to use machine learning in our prediction approach. Our evaluation on 16 HPC benchmarks shows that PARIS achieves high prediction accuracy. PARIS is up to 450x faster than random FI (49x on average). Compared to the state-of-the-art analytical model, PARIS is at least 63% better in terms of accuracy and has comparable execution time on average.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

The Dynamics of Ions on Phased Radio-frequency Carpets in High Pressure Gases and Application for Barium Tagging in Xenon Gas Time Projection Chambers

Radio-frequency (RF) carpets with ultra-fine pitches are examined for ion transport in gases at atmospheric pressures and above. We develop new analytic and computational methods for modeling RF ion transport at densities where dynamics are strongly influenced by buffer gas collisions. An analytic description of levitating and sweeping forces from phased arrays is obtained, then thermodynamic and kinetic principles are used to calculate ion loss rates in the presence of collisions. This methodology is validated against detailed microscopic SIMION simulations. We then explore a parameter space of special interest for neutrinoless double beta decay experiments: transport of barium ions in xenon at pressures from 1 to 10 bar. Our computations account for molecular ion formation and pressure dependent mobility as well as finite temperature effects. We discuss the challenges associated with achieving suitable operating conditions, which lie beyond the capabilities of existing devices, using presently available or near-future manufacturing techniques.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

Methodology for inferring reactor core power distribution from an optical fiber based gamma thermometer array

Here, a 4-step data analytic methodology has been devised for the purpose of inferring the distribution of power in a reactor core, based on the response of an array of optical fiber based gamma thermometers (OFBGTs). This data analytic methodology is crucial for the development of a system of OFBGTs for the purpose of calibrating local power range monitors in boiling water reactors. Such a system would be an improvement to the present calibration system in boiling water reactors, in terms of safety, efficiency, and permanence. The first step of this methodology is to establish an energy balance method. In this method, one uses MCNP to determine response functions, which allow one to convert from gamma thermometer response to power. The gamma thermometers and the reactor core are segmented, such that each gamma thermometer segment provides an estimate of power for each reactor core segment. The estimates of power for the reactor core segments (hereafter referred to as fuel assembly segments) are calculated based on the measured response of the gamma thermometers. The second step of the methodology is to employ a weighting scheme to combine the estimates of the power of the various fuel assembly segments, based on the response of the various OFGBT segments and the incremental dose rates of the various fuel assembly segments to the OFBGT segments. The third step is to iteratively calculate the estimates of the power of the fuel assembly segments, until a convergence criterion is met, which indicates that the calculation has converged. The fourth and final step of the methodology is to estimate the uncertainty of the power for each fuel assembly segment. The mathematical basis for this step is not the focus of this paper. We have used a 3-D homogeneous reactor model to demonstrate the data analytic methodology; and have found that the data analytic methodology operates as intended.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2025

Deciphering Reaction Mechanisms of Molecular Proton Reduction Catalysts with Cyclic Voltammetry: Kinetic vs Thermodynamic Control

The kinetics and thermodynamics of elementary reaction steps involved in the catalytic reduction of protons to hydrogen define the reaction landscape for catalysis. The mechanisms can differ in the order of the elementary proton transfer, electron transfer, and bond-forming steps and can be further differentiated by the sites at which protons and electrons localize. Access to fully elucidated mechanistic, kinetic, and thermochemical details of molecular catalysts is crucial to facilitate the development of new catalysts that operate with optimal efficiency, selectivity, and durability. The mechanism by which a catalyst operates, as well as the kinetics and thermodynamics associated with the individual steps, can often be accessed through electroanalytical studies. Here, this Account details the application of cyclic voltammetry to interrogate reaction mechanisms and quantify the kinetics and thermodynamics of elementary reaction steps for a series of molecular catalysts that mediate electrochemical proton reduction. I distinguish the limiting scenarios wherein a catalyst operates under kinetic control vs thermodynamic control, with a focus on detecting how cyclic voltammetry features shift with proton source strength and concentration, as well as scan rate. For systems that operate under kinetic control, catalytic currents are observed at, or slightly positive toward, the formal potential for the redox process that triggers catalysis. Under thermodynamic control, catalytic responses shift as a function of the proton source pKa and effective pH of the solution. After drawing this distinction, we introduce the appropriate voltammetry experiments and accompanying analytical expressions for extracting key metrics from the data. To illustrate analytical strategies to quantify elementary reaction steps of catalysts operating under kinetic control, I describe our studies of proton reduction catalysts Co(dmgBF 2 ) 2 (CH 3 CN) 2 (dmgBF 2 = difluoroboryl-dimethylglyoxime) and [Ni(P 2 Ph N 2 Ph ) 2 ] 2+ (P 2 Ph N 2 Ph = 1,5-phenyl-3,7-phenyl-1,5-diaza-3,7-diphosphacyclooctane). Here, peak shift analysis, foot-of-the-wave analysis, and plateau current analysis are applied to data sets wherein voltammetric response are recorded as a function of catalyst concentration, proton source concentration, proton source strength, and scan rate to quantify rate constants for elementary proton transfer and bond-forming steps in a catalytic cycle. Further, the case study of [Ni(P 2 Ph N 2 Ph ) 2 ] 2+ illustrates how complementary spectroscopic methods can bolster the mechanistic assignment. Collectively, these two studies showcase how detailed mechanistic studies inform on rate-limiting elementary steps in catalysis and other key processes underpinning catalysis. Second, I present analytical strategies to interrogate catalysts operating under thermodynamic control, centered on the case study of [Ni II (P 2 Ph N 2 Bn ) 2 ] 2+ (P 2 Ph N 2 Bn = 1,5-dibenzyl-3,7-diphenyl-1,5-diaza-3,7-diphosphacyclooctane). Here, the application of nonaqueous Pourbaix theory to extract thermodynamic information is introduced, and the construction of a coupled Pourbaix diagram is detailed. This study identifies ligand-based protonation as the key process that places catalysis under thermodynamic control and influences the reaction mechanism. Together, the work detailed in this Account showcases the utility of electroanalytical methods to disentangle complex reaction mechanisms and extract key thermochemical and kinetic parameters for elementary steps of catalysis. Through detailed presentation of the key analytical expressions that underpin these analyses, this Account seeks to facilitate the adoption of cyclic voltammetry by the community to fully extract kinetic, thermochemical, and mechanistic information on electrochemical small-molecule activation.

catalysts↗
DOE OSTI2021

Transport Modeling of Kinetically Limited Microscale Extraction Systems: Droplet and Supported Liquid Membrane Separations

Microfluidic droplet extraction devices can be used to efficiently measure solute phase transfer kinetics in liquid–liquid extraction systems. In this work, a droplet extraction apparatus was constructed using off-the-shelf and custom 3D printed parts for less than 110 USD. The interfacial kinetics of the transfer of Pu(IV) between an aqueous nitric acid phase and a 5 v/v% tridodecylamine (TDA) in toluene phase were characterized by determining the extent of Pu(IV) transfer between phases at different flow rates. Forward interfacial rate constants calculated from this data using an analytical model are 5.6 × 10 –3 mm s –1 under extraction (aqueous-to-organic solute transfer) conditions and 3.3 × 10 –3 mm s –1 under stripping (organic-to-aqueous solute transfer) conditions. The analytical model is valid when the rate of solute transfer across the interface between the two liquid phases has pseudo-first-order reversible reaction kinetics and is slow relative to the rate of solute transport to the interface. The change in the outlet concentration with residence time determined using the analytical model was compared with the results of a numerical model accounting for advection/diffusion to the interface in addition to kinetically limited interfacial solute transfer. These calculations revealed that for systems with forward interfacial rate constants greater than approximately 10 –2 mm s –1 , the analytical model must be supplemented with a numerical transport model accounting for an additional advection/diffusion mass transfer resistance. This threshold corresponds to a Damköhler number of one. The measured interfacial kinetic rate constants for Pu(IV)/TDA were used in a supported liquid membrane (SLM) numerical model, which showed that the Pu(IV) phase transfer kinetics are fast enough for use in a practical separation.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2021

Adsorbate Free Energies from DFT-Derived Translational Energy Landscapes

Adsorption free energies are fundamental to surface chemistry and catalysis. Standard models combine some assumed analytical form of the translational potential energy surface, often parameterized against density functional theory (DFT) calculations, with an analytical expression for the resultant translational densities of states (DOS), free energy, and entropy. Here we compare the performance of such models against numerical evaluations of the DOS and thermodynamic functions derived from solutions to the translational Schrodinger equation. We compare results for a translational potential energy surface (PES) derived from nudged eleastic band calculations with those obtained from adsorbate rastering across a series of monatomic (O, S, C, N, H) and polyatomic (NH x ) adsorbates on (100) Pt and Au facets. We find that analytical models as commonly parameterized have mixed performance for describing the translational PES and that the consequences for computed free energies are modest but potentially significant in microkinetic models. Here, numerical solutions are possible for modest to no additional computational cost over analytical models and thus should be considered when reliable free energy estimates are needed or translational potential energy surfaces are available.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

Versatile Cell Design for Molten Fluoride Salt Spectroscopy: Investigating Metal-Ion Speciation in Molten Fluoride Salts

Fluoride-based molten salts are widely used in industrial applications including aluminum production, thermal energy storage, optical crystal growth, and advanced nuclear reactor designs. Despite the wide range of uses, fundamental understandings of coordination chemistry and methods for probing molten fluorides are scarce, likely due to the difficulty of probing fluoride melts with spectroscopic techniques. Performing spectroscopic measurements of fluoride-based salts is challenging due to the highly corrosive nature of these salts, which can degrade many common optical materials. Here, in this work, we present a versatile optical cell design that enables spectroscopic measurements of corrosive melts. This innovative cell design overcomes the challenges posed by the corrosive nature of the salts, allowing for an accurate and consistent spectroscopic analysis. This work reports temperature-dependent absorption measurements for Co 2+ , Ni 2+ , and Cr 3+ analytes in LiF-NaF-KF eutectic salt (i.e., FLiNaK), which are common corrosion products originating from structural alloys in molten-fluoride handling. Absorption spectra were used to understand interactions of these analytes with FLiNaK, particularly ligand field coordination. The analysis of absorption spectra was complemented by structural analyses using ab initio molecular dynamics (AIMD) simulations, providing deeper insights into the behavior of the analytes in FLiNaK. Our findings indicate that the analytes studied in this work exist in octahedral or near-octahedral coordination states that remain stable across the temperature range of 500–600 °C. This work not only highlights an applied solution to performing optical spectroscopy in corrosive, high-temperature melts but also provides important fundamental insight on coordination behavior of transition-metal species in molten fluorides.

Fluoride salt spectroscopy↗
DOE OSTI2024

Self‐Potential Tomography Preconditioned by Particle Swarm Optimization—Application to Monitoring Hyporheic Exchange in a Bedrock River

Abstract A self‐potential (SP) data‐inversion algorithm was developed and tested on an analytical model of electrical‐potential profile data attributed to single and multiple polarized electrical sources. The developed algorithm was then validated by an application to SP‐monitoring field data measured on the floodplain of East Fork Poplar Creek, Oak Ridge, Tennessee, to image electrical sources in areas conducive to preferential flow into the flood plain from the bedrock‐lined riverbed. The algorithm combined stochastic source‐localization by particle‐swarm‐optimization (PSO) of electrical sources characterized by simplified geometries with source tomography by regularized weighted least‐squares minimization of a quadratic objective function. Prior information was incorporated by preconditioning the tomography algorithm by PSO results. Variable percentages of random noise were added to analytical‐model data to evaluate the algorithm performance. Results indicated that true parameters of single‐source models were inverted and approximated with small residual error, whereas inversion of analytical‐model data representing multiple electrical sources accurately approximated the locations of the sources but miscalculated some parameters because of the non‐uniqueness of the inverse‐model solution. Source tomography applied to analytical model data during testing produced a spatially continuous parameter field that identified the locations of point‐scale synthetic dipole sources of electrical current flow with varying degrees of accuracy depending on the prior information incorporated into the tomography. When applied to SP‐monitoring field data, the algorithm imaged electrical sources within a known fault that intersects the bedrock riverbed and flood plain of East Fork Poplar Creek and depicted dynamic electrical conditions attributed to hyporheic exchange.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

On the Impact of Bus Dwelling on Macroscopic Fundamental Diagrams

Network macroscopic fundamental diagrams (MFDs) have recently been shown to exist in real-world urban traffic networks. When present, MFDs can be used to model traffic dynamics within an urban network by dividing the network into a set of spatially compact homogeneous regions and tracking the average level of congestion in each region. Existing analytical methods to estimate MFD mostly focus on the behavior of a single type of vehicle and do not capture the patterns of mixed traffic (e.g., cars and buses). The existence of buses matters since a bus will block the movements of other vehicles when it dwells at the bus stop. This paper proposes an analytical method to estimate the impact of bus dwelling on a network’s MFD based on the network’s geometric features, traffic control strategies, and bus operation parameters, and validates the performance of the proposed method using simulations based on microscopic traffic models. Comparisons of the analytical and simulation results show that the proposed analytical method can generally provide a good estimate of the lower bound and upper bound of the network’s MFD.

Xu, Guanhao↗
DOE OSTI2021

Plasma heating and current sheet structure in anti-parallel magnetic reconnection

A theoretical model and an analytic theory of current sheet structure are presented for understanding anti-parallel driven magnetic reconnection in 2-1/2 dimension in collisionless plasmas. The theoretical model provides formulation to compute the current sheet y-profiles by specifying the profiles of electron and ion flow velocities V ex (x,y) and V ix (x,y). The current sheet solutions depend on the plasma density n in , merging magnetic field B 0 , ion velocity v i , and electron velocity ve in the upstream and the S evz =V ez /V dz parameter where V ez is the electron velocity accelerated by the reconnection electric field E z in the electron orbit meandering region, V dz ≃cE y /B x is the $\overrightarrow{E}$ × $\overrightarrow{B}$ drift velocity as electrons enter the orbit meandering region, B x is the merging magnetic field, and E y is the electrostatic electric field. With simplifying assumptions on the y-profiles of V ex and V ix , we have also developed an analytic theory of the current sheet structure. Analytic expressions for the anomalous resistivity, the electrostatic potential drop, and the maximum E y amplitude E max are obtained. The analytic results agree reasonably well with both the particle-in-cell simulation results and the numerical solutions of the theoretical model. The ions energy gain due to the potential drop is $∝B^2_0/n_{in}$. The electron energy gain is $∝(B^2_0 /8πn_{in})S_{evz}$. The $B^2_0/n_{in}$ scaling of the average ion and electron energy gains are consistent with laboratory experiments and space plasma observations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Finite-difference multiple fluid solution for source-driven rotation in highly magnetized linear plasma device

The rotation profile of a magnetized plasma cylinder composed of multiple fluids is investigated analytically, expanding on previous results. The analytic steady-state solution is used as a benchmark for a time-dependent multiple-fluid finite-difference code, MITNS: Multiple-Ion Transport Numerical Solver. Magnetic field evolution is taken into account, both analytically and numerically. Its details are shown to be of importance when particles are allowed out of the domain. MITNS reproduces the asymptotic expansion results for a small parameter $δ<<<1$. For $\sqrt{m_elm_i} ~ δ << 1$ , a slightly different regime, dominated by viscosity-induced transport of ions, is found numerically and analytically. Finally, this verification supports the use of this code for more complex time-dependent calculations in the future. Additionally, we derive the angular velocity profile of each species due to radial particle and charge fluxes of various strengths.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Planar turbulent wakes under pressure gradient: Integral and self-similarity analyses

By using a combination of integral and self-similarity analyses, the generalized analytical solutions for the mean transverse velocity and Reynolds shear stress are rigorously derived for the first time for the far field of planar turbulent wakes under arbitrary pressure gradients. Specifically, by assuming self-similarity for the mean axial velocity, the analytical formulation for the mean transverse velocity is obtained from the integral of the mean continuity equation, and the analytical formulation for the Reynolds shear stress is obtained from the integral of the momentum equation. The generalized analytical formulations for the mean transverse velocity and Reynolds shear stress consist of multiple components, each with its unique scale and physical mechanism. In the zero pressure gradient limit, the generalized formulations recover the single-scale equations reported by Wei, Liu, and Livescu. Furthermore, simpler approximate formulations for the mean transverse velocity and Reynolds shear stress are also obtained, and show excellent agreement with the experimental measurements. Here, the findings provide new insights into the properties of planar turbulent wakes under pressure gradients, filling some long-standing gaps in the existing literature.

42 ENGINEERING↗
DOE OSTI2024

Distribution of centrality measures on undirected random networks via the cavity method

The Katz centrality of a node in a complex network is a measure of the node’s importance as far as the flow of information across the network is concerned. For ensembles of locally tree-like undirected random graphs, this observable is a random variable. Its full probability distribution is of interest but difficult to handle analytically because of its “global” character and its definition in terms of a matrix inverse. Leveraging a fast Gaussian Belief Propagation-Cavity algorithm to solve linear systems on tree-like structures, we show that i) the Katz centrality of a single instance can be computed recursively in a very fast way, and ii) the probability P ( K ) that a random node in the ensemble of undirected random graphs has centrality K satisfies a set of recursive distributional equations, which can be analytically characterized and efficiently solved using a population dynamics algorithm. We test our solution on ensembles of Erdős-Rényi and Scale Free networks in the locally tree-like regime, with excellent agreement. The analytical distribution of centrality for the configuration model conditioned on the degree of each node can be employed as a benchmark to identify nodes of empirical networks with over- and underexpressed centrality relative to a null baseline. We also provide an approximate formula based on a rank- 1 projection that works well if the network is not too sparse, and we argue that an extension of our method could be efficiently extended to tackle analytical distributions of other centrality measures such as PageRank for directed networks in a transparent and user-friendly way.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2026

Propagation of partially spatially coherent laser beams in instantaneous Kerr media

The propagation of intense, partially spatially coherent laser beams in a medium with instantaneous third-order susceptibility is studied analytically and numerically. For sufficiently high power relative to that required for nonlinear self-focusing, the propagation initially proceeds in two stages. In the first stage, spatial coherence builds up, and in the second stage, the number of speckles reduces. Once the degree of coherence is sufficiently high, whole-beam self-focusing occurs. The beam power is mostly confined within the initial spot radius. Two analytical approaches for describing the evolution of the beam are presented. The method of moments leads to an analytical solution for the rms spot radius that is in excellent agreement with simulations. This method does not require any knowledge of the field statistics beyond the initial conditions and provides no information about the evolution of the individual speckles. The other approach employs a self-similar solution for the second-order coherence function of the field and assumes that the fourth-order coherence function is factorizable and obeys complex circular Gaussian random statistics. The latter method also leads to an analytical expression for the spot radius, but its predictions for the qualitative evolution of the speckles disagree with wave-optics simulations.

lasers↗
DOE OSTI2025

Acausality-driven instabilities in relativistic viscous hydrodynamics

We investigate non-linear instabilities stemming from superluminal propagation of information in Israel-Stewart-like models of relativistic viscous fluid dynamics. In relativity, the characteristic speed of propagation of information, $w$, and the speed of the fluid, $v$, allow us to differentiate between regimes of the hydrodynamic equations that are acausal but stable ($w>1$), unstable ($v^{2} w^{2} \geq 1$), and covariantly ill-posed ($w^{2} \leq 0$). As an analytical benchmark, we present a new solution that illustrates these distinct regimes. We compare this analytical solution to the result of a numerical relativistic viscous fluid dynamics solver, and confirm that the analytical result can be recovered numerically in the stable regime, whether causal or acausal. The onset of numerical instabilities is further found to occur in the regime predicted by the analytical solution.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗