Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Wing loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Results from a test of a 2/3-scale V-22 rotor and wing in the 40- by 80-Foot Wind Tunnel

A test of a 0.658-scale V-22 rotor and wing was conducted in the 40- by 80-Foot Wind Tunnel at Ames Research Center. The principal objectives of the test were to measure the wing download in hover for a variety of test configurations, and rotor performance in forward flight. Also, a limited amount of data on rotor performance in vertical climb were acquired. This paper presents the results from the test with predictions from appropriate analytical methods. A new method for presenting and interpreting wing surface pressure data in hover is described, and this method shows that the wing flap can produce substantial lift loads in hover. The rotor performance in vertical climb was underpredicted by CAMRAD/JA and by the free wake analysis EHPIC. A simple momentum theory is presented which provides good predictions of rotor performance in forward flight.

Felker, Fort F.↗
NASA NTRS1991

Experimental measurement of structural intensity on an aircraft fuselage

An experimental technique was used to measure structural intensity through an aircraft fuselage with an excitation load applied near one of the wing attachment locations. The fuselage was relatively large, requiring several measurement locations to analyze the intensity flow through the whole of the structure. For the measurement of structural intensity, the use of a transducer array was necessary at every location of interest. A trade-off was therefore required between the number of measurement transducers, the mounting of these transducers, and the accuracy of the measurements. Using four accelerometers mounted on a bakelite platform, structural intensity vectors were measured at locations distributed throughout the fuselage. The results of these measurements, together with a discussion on the suitability of the approach for measuring structural intensity on a real structure, are presented in this paper.

Cuschieri, J. M.↗
NASA NTRS1948

Results obtained during accelerated transonic tests of the Bell XS-1 airplane in flights to a Mach number of 0.92

Results are presented of tests up to a Mach number of 0.92 at altitudes around 30,000 feet. The data obtained show that the airplane can be flown to this Mach number above 30,000 feet. Longitudinal trim changes have been experienced but the forces involved have been small. The elevator effectiveness decreased about one-half with increase of Mach number from 0.70 to 0.87. Buffeting has been experienced in level flight but it has been mild and the associated tail loads have been small. No aileron buzz or other flutter phenomena have been noted.

STABILITY, LONGITUDINAL - DYNAMIC↗
NASA NTRS1951

Investigation of the Effects of Twist and Camber on the Aerodynamic Characteristics of a 50 Degrees 38 Minutes Sweptback Wing of Aspect Ratio 2.98 : Transonic-bump Method

An investigation of two semispan wings swept back 50 degrees 38 minutes was conducted in the Langley high-speed 7- by 10-foot tunnel over a Mach number range of 0.68 to 1.15 by use of the transonic-bump technique. This paper presents the results of the investigation of wing-alone and wing-fuselage configurations of the two wings; one was an untwisted uncambered wing and the other was the same wing but incorporated twist and camber designed to give uniform load at a lift coefficient of 0.25 at a Mach number of 1.10. The semispan wings had their quarter-chord lines swept back 50 degrees 38 minutes, aspect ratios 2.98, taper ratios 0.45, and modified NACA 64A-series airfoil sections tapered in thickness. Lift, pitching moment, drag, and bending moment were obtained for these configurations.

WINGS, COMPLETE - DESIGN VARIABLES↗
NASA NTRS1932

Span-Load Distribution as a Factor in Stability in Roll

This report gives the results of pressure-distribution tests made to study the effects on lateral stability of changing the span-load distribution on a rectangular monoplane wing model of fairly thick section. Three methods of changing the distribution were employed: variation in profile along the span to a thin symmetrical section at the tip, twist from +5 degrees to -15 degrees at the tip, and sweepback from +20 degrees to -20 degrees. The tests were conducted in a 5-foot closed-throat atmospheric wind tunnel. The investigation shows the following results: (1) change in profile along the span from the NACA-84 at the root to the NACA-M2 at the tip considerably reduces lateral instability, but also reduces the general effectiveness of the wing. (2) washout up to 11 degrees progressively reduces maximum lateral instability. (3) transition from sweepforward to sweepback gradually reduces the useful angle-of-attack range, but has no clearly defined effect on maximum lateral instability.

Knight, Montgomery↗
NASA NTRS1951

Stability of the cylindrical shell of variable curvature

This report is a first attempt to devise a calculation method for representing the buckling behavior of cylindrical shells of variable curvature. The problem occurs, for instance, in dimensioning wing noses, the stability of which is decisively influenced by the variability of curvature. The calculation is made possible by simplifying the stability equations (permissible for the shell of small curvature) and by assuming that the curvature 1/R as a function of the arc lengths can be represented by a very few Fourier terms. The formulas for the special case of an ellipse-like half oval with an axis ratio 1/3 ?= e ?= 1 under compression in longitudinal direction,shear, and a combination of shear and compression were evaluated. However, the results can also be applied approximately to an unsymmetrical oval-shell segment under compression, shear, and bending so that the numerical values contained in the diagrams 10 to 12 represent directly dimensioning data for the wing nose.

LOADS AND STRESSES, STRUCTURAL - BENDING↗
NASA NTRS1996

Full scale GLARE fuselage panel tests

A GLARE fuselage panel, representative of the crown section of the Fokker 100 fuselage in front of the wing, was tested. The panels were loaded by air pressure resulting in tangential stress in the panel by axial loading, representative of both the cabin pressure and the fuselage bending due to taxiing and gust loading. A fatigue test, simulating 180000 flights, followed by static tests were performed. The panel was loaded to failure at 1.32 ultimate load. The test set-up, the uniform strain distribution of the panel, and the fatigue loads applied at high test frequency are described. The use of GLARE leads to a substantial weight reduction without affecting the fatigue static strength.

Vercammen, Roland W. A.↗
NASA NTRS1999

Navier-Stokes Analysis of the Flowfield Characteristics of an Ice Contaminated Aircraft Wing

An analytical study was performed as part of the NASA Lewis support of a National Transportation Safety Board (NTSB) aircraft accident investigation. The study was focused on the performance degradation associated with ice contamination on the wing of a commercial turbo-prop-powered aircraft. Based upon the results of an earlier numerical study conducted by the authors, a prominent ridged-ice formation on the subject aircraft wing was selected for detailed flow analysis using 2-dimensional (2-D), as well as, 3-dimensional (3-D) Navier-Stokes computations. This configuration was selected because it caused the largest lift decrease and drag increase among all the ice shapes investigated in the earlier study. A grid sensitivity test was performed to find out the influence of grid spacing on the lift, drag, and associated angle-of-attack for the maximum lift (C(sub lmax)). This study showed that grid resolution is important and a sensitivity analysis is an essential element of the process in order to assure that the final solution is independent of the grid. The 2-D results suggested that a severe stability and control difficulty could have occurred at a slightly higher angle-of-attack (AOA) than the one recorded by the Flight Data Recorder (FDR). This stability and control problem was thought to have resulted from a decreased differential lift on the wings with respect to the normal loading for the configuration. The analysis also indicated that this stability and control problem could have occurred whether or not natural ice shedding took place. Numerical results using an assumed 3-D ice shape showed an increase of the angle at which this phenomena occurred of about 4 degrees. As it occurred with the 2-D case, the trailing edge separation was observed but started only when the AOA was very close to the angle at which the maximum lift occurred.

Chung, J.↗
NASA NTRS1992

Wing Download Results from a Test of a 0.658-Scale V-22 Rotor and Wing

A test of a 0.658-scale V-22 rotor and wing was conducted in the 40 x 80 Foot Wind Tunnel at Ames Research Center. One of the principal objectives of the test was to measure the wing download in hover for a variety of test configurations. The wing download and surface pressures were measured for a wide range of thrust coefficients, with five different flap angles, two nacelle angles, and both directions or rotor rotation. This paper presents these results, and describes a new method for interpreting wing surface pressure data in hover. This method shows that the wing flap can produce substantial lift loads in hover.

Felker, Fort F.↗
NASA NTRS2005

Discrete Event Supervisory Control Applied to Propulsion Systems

The theory of discrete event supervisory (DES) control was applied to the optimal control of a twin-engine aircraft propulsion system and demonstrated in a simulation. The supervisory control, which is implemented as a finite-state automaton, oversees the behavior of a system and manages it in such a way that it maximizes a performance criterion, similar to a traditional optimal control problem. DES controllers can be nested such that a high-level controller supervises multiple lower level controllers. This structure can be expanded to control huge, complex systems, providing optimal performance and increasing autonomy with each additional level. The DES control strategy for propulsion systems was validated using a distributed testbed consisting of multiple computers--each representing a module of the overall propulsion system--to simulate real-time hardware-in-the-loop testing. In the first experiment, DES control was applied to the operation of a nonlinear simulation of a turbofan engine (running in closed loop using its own feedback controller) to minimize engine structural damage caused by a combination of thermal and structural loads. This enables increased on-wing time for the engine through better management of the engine-component life usage. Thus, the engine-level DES acts as a life-extending controller through its interaction with and manipulation of the engine s operation.

Litt, Jonathan S.↗
NASA NTRS2012

Lessons in the Design and Characterization Testing of the Semi-Span Super-Sonic Transport (S4T) Wind-Tunnel Model

This paper focuses on some of the more challenging design processes and characterization tests of the Semi-Span Super-Sonic Transport (S4T)-Active Controls Testbed (ACT). The model was successfully tested in four entries in the National Aeronautics and Space Administration Langley Transonic Dynamics Tunnel to satisfy the goals and objectives of the Fundamental Aeronautics Program Supersonic Project Aero-Propulso-Servo-Elastic effort. Due to the complexity of the S4T-ACT, only a small sample of the technical challenges for designing and characterizing the model will be presented. Specifically, the challenges encountered in designing the model include scaling the Technology Concept Airplane to model scale, designing the model fuselage, aileron actuator, and engine pylons. Characterization tests included full model ground vibration tests, wing stiffness measurements, geometry measurements, proof load testing, and measurement of fuselage static and dynamic properties.

Source record↗
NASA NTRS2013

Methodologies for Combined Loads Tests Using a Multi-Actuator Test Machine

The NASA Langley COmbined Loads Test System (COLTS) Facility was designed to accommodate a range of fuselage structures and wing sections and subject them to both quasistatic and cyclic loading conditions. Structural tests have been conducted in COLTS that address structural integrity issues of metallic and fiber reinforced composite aerospace structures in support of NASA Programs (i.e. the Aircraft Structural Integrity (ASIP) Program, High-Speed-Research program and the Supersonic Project, NASA Engineering and Safety Center (NESC) Composite Crew Module Project, and the Environmentally Responsible Aviation Program),. This paper presents experimental results for curved panels subjected to mechanical and internal pressure loads using a D-box test fixture. Also, results are presented that describe use of a checkout beam for development of testing procedures for a combined mechanical and pressure loading test of a Multi-bay box. The Multi-bay box test will be used to experimentally verify the structural performance of the Multi-bay box in support of the Environmentally Responsible Aviation Project at NASA Langley.

Rouse, Marshall↗
NASA NTRS2015

Level-Set Topology Optimization with Aeroelastic Constraints

Level-set topology optimization is used to design a wing considering skin buckling under static aeroelastic trim loading, as well as dynamic aeroelastic stability (flutter). The level-set function is defined over the entire 3D volume of a transport aircraft wing box. Therefore, the approach is not limited by any predefined structure and can explore novel configurations. The Sequential Linear Programming (SLP) level-set method is used to solve the constrained optimization problems. The proposed method is demonstrated using three problems with mass, linear buckling and flutter objective and/or constraints. A constraint aggregation method is used to handle multiple buckling constraints in the wing skins. A continuous flutter constraint formulation is used to handle difficulties arising from discontinuities in the design space caused by a switching of the critical flutter mode.

Dunning, Peter D.↗
DOE OSTI2014

Submerged electricity generation plane with marine current-driven motors

An underwater apparatus for generating electric power from ocean currents and deep water tides. A submersible platform including two or more power pods, each having a rotor with fixed-pitch blades, with drivetrains housed in pressure vessels that are connected by a transverse structure providing buoyancy, which can be a wing depressor, hydrofoil, truss, or faired tube. The platform is connected to anchors on the seafloor by forward mooring lines and a vertical mooring line that restricts the depth of the device in the water column. The platform operates using passive, rather than active, depth control. The wing depressor, along with rotor drag loads, ensures the platform seeks the desired operational current velocity. The rotors are directly coupled to a hydraulic pump that drives at least one constant-speed hydraulic-motor generator set and enables hydraulic braking. A fluidic bearing decouples non-torque rotor loads to the main shaft driving the hydraulic pumps.

13 HYDRO ENERGY↗