Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Water System”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58
All sourcesNASA NTRSDOE OSTI
DOE OSTI2012

Collection of Lanthanides and Actinides from Natural Waters with Conventional and Nanoporous Sorbents

Effective collection of trace-level lanthanides and actinides is advantageous for recovery and recycling of valuable resources, environmental remediation, chemical separations and in-situ monitoring. Using isotopic tracers, we have evaluated a number of conventional and nanoporous sorbent materials for their ability to capture and remove selected lanthanides (Ce and Eu) and actinides (Th, Pa, U, and Np) from fresh and salt water systems. In general, the nanostructured materials demonstrated a higher level of performance and consistency. Nanoporous silica surface modified with 3,4- hydroxypyridinone provided excellent collection and consistency in both river water and seawater. The MnO2 materials, particular the high surface area small particle material also demonstrated good performance. Other conventional sorbents typically performed at the levels below the nanostructured sorbents and demonstrate a larger variability and matrix dependency.

Actinide, lanthanide, mesoporous, nanoporous, mang↗
NASA NTRS2024

Short Exploration Extravehicular Mobility Unit Testing Setup: Evaluation Under Realistic Pressure and Thermal Conditions

The purpose of Short Exploration Extravehicular Mobility Unit (SxEMU) thermal vacuum testing was to verify the functionality of the Design Verification Testing (DVT) prototype xEMU (SxEMU for this test) at vacuum pressures and extreme space and lunar surface temperature conditions. The SxEMU Thermal Vacuum Test was the culmination of the DVT xEMU project. This paper’s focus is on the pre-Extravehicular Activity (EVA) test setup, and general performance of the SxEMU Portable Life Support Subsystem (xPLSS), with focus on the performance of the Primary Oxygen Assembly (POA) and Secondary Oxygen Assembly (SOA), including Secondary Oxygen Regulator (SOR) takeover and the POA and SOA low-setpoint change inhibit. The initial pre-EVA test preparation included recharging the batteries and replenishing consumables, including test-system water, oxygen assemblies (with gaseous nitrogen), and the integrated thermal loops, including the Feedwater Supply Assemblies. xPLSS functionality testing included carbon dioxide (CO2) removal via the Rapid Cycle Amine swingbed system, thermal loop temperature control, and monitoring of suit ventilation loop pressure, temperature, and CO2 percentages. Testing evaluated automatic takeover of suit pressure control by the SOR after the primary oxygen supply is depleted. The Primary Oxygen Regulator and SOR low-setpoint change inhibit function prevents the crewmember from inadvertently setting the primary regulator to a low pressure setpoint during an EVA.

xPLSS↗
DOE OSTI2020

Policy Brief: Integrated Nexus Policies for Sustainable and Resilient Energy, Water, and Food Systems

Population growth, climate change, and resource depletion put food and water security and energy supply at risk. Sustainable and resilient water, food, and energy systems are crucial to meet Sustainable Development Goals (SDGs) and increase resilience to global health crises such as the COVID-19 pandemic. This policy brief describes the challenges and presents proposals regarding synergies in the land, water, and energy nexus to maximize net environmental, health, and social benefits. First, this brief focuses on water desalination, where the nexus approach helps to balance the full cost, including externalities, of desalinated water, and its socio-economic benefits. Second, this policy brief highlights nutrition-sensitive food policies that improve health and contribute to the preservation of natural resources. Finally, this brief presents challenges and opportunities for developing renewable energy.

energy↗
DOE OSTI2020

Physical drivers facilitating a toxigenic cyanobacterial bloom in a major Great Lakes tributary

The Maumee River is the primary source for nutrients fueling seasonal Microcystis -dominated blooms in western Lake Erie's open waters though such blooms in the river are infrequent. The river also serves as source water for multiple public water systems and a large food services facility in northwest Ohio. On 20 September 2017, an unprecedented bloom was reported in the Maumee River estuary within the Toledo metropolitan area, which triggered a recreational water advisory. Here we (1) explore physical drivers likely contributing to the bloom's occurrence, and (2) describe the toxin concentration and bacterioplankton taxonomic composition. A historical analysis using 10-years of seasonal river discharge, water level, and local wind data identified two instances when high-retention conditions occurred over ≥ 10 d in the Maumee River estuary: in 2016 and during the 2017 bloom. Observation by remote sensing imagery supported the advection of cyanobacterial cells into the estuary from the lake during 2017 and the lack of an estuary bloom in 2016 due to a weak cyanobacterial bloom in the lake. A rapid-response survey during the 2017 bloom determined levels of the cyanotoxins, specifically microcystins, in excess of recreational contact limits at sites within the lower 20 km of the river while amplicon sequencing found these sites were dominated by Microcystis . These results highlight the need to broaden our understanding of physical drivers of cyanobacterial blooms within the interface between riverine and lacustrine systems, particularly as such blooms are expected to become more prominent in response to a changing climate.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2018

Microbial source tracking markers associated with domestic rainwater harvesting systems: Correlation to indicator organisms

Highlights: • Microbial source tracking markers are present in harvested rainwater. • HF183, Lachnospiraceae, B. adolescentis and adenovirus correlate with indicators. • HF183, adenovirus and Lachnospiraceae co-occurred with indicator organisms. • These MST markers may be incorporated in a toolbox to supplement indicator analysis. Domestic rainwater harvesting (tank water) systems were screened for the presence of a panel of microbial source tracking (MST) markers and traditional indicator organisms. The indicator organisms were enumerated utilizing traditional culture-based methods, while the MST markers were quantified by quantitative PCR (qPCR). The indicators Escherichia coli (E. coli) and enterococci were also quantified using qPCR. Correlations and concurrence between these parameters were then investigated to determine which markers could be utilized to supplement traditional indicator analysis. Quantitative PCR analysis indicated that Bacteroides HF183, adenovirus, Lachnospiraceae and E. coli were detected and quantifiable in 100% of the tank water samples collected throughout the sampling period, while human mitochondrial DNA (mtDNA) was quantifiable in 90% of the tank water samples and Bifidobacterium adolescentis (B. adolescentis) and enterococci were quantifiable in 67% of the tank water samples, respectively. Significant positive correlations were recorded for Lachnospiraceae versus heterotrophic bacteria (p = 0.000), adenovirus versus E. coli (culturing) (p = 0.000) and heterotrophic bacteria (p = 0.024), the HF183 marker versus E. coli (qPCR) (p = 0.024) and B. adolescentis versus fecal coliforms (p = 0.037). In addition, 100% concurrence was observed for the HF183 marker, adenovirus and Lachnospiraceae versus E. coli (qPCR), enterococci (qPCR) and heterotrophic bacteria, amongst others. Based on the correlations and the concurrence analysis, the HF183 marker, Lachnospiraceae and adenovirus may be utilized to supplement indicator organism analysis for the monitoring of harvested rainwater quality.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Performance study of a novel dew point evaporative cooler in the climate of central Europe using building simulation tools

This paper presents the performance research of a hybrid air conditioning system (System II) equipped with novel dew point evaporative cooler (DPIEC) for a retail building located in temperate climatic conditions. The new cooler has a dedicated, adaptable structure that maximizes its performance in the climate conditions of central Europe. The unit can operate as a typical regenerative air cooler when outdoor air is drier than indoor air, it can operate as a counter-flow heat recovery unit when indoor conditions are more dry than outdoor and it can operate as a combination of both arrangements. The year-round, hourly-stepped building energy simulations were carried-out using a prognostic tool of energy consumption. The novel dew point evaporative cooler application potential was established using the black-box model based on regression equations was established based on experimental tests on a prototype of novel DPIEC. The hybrid system operation was compared to the typical air handling unit equipped with a standard energy wheel for heat recovery (System I). Presented research shows that DPIEC can cover about 95% of total cooling loads while the energy wheel covers only 9% of total cooling load. System II allows us to save 65% of seasonal electricity consumption comparing to System I. It comes from the fact that during most of the cooling season DPIEC is in operation and it covers most of the cooling loads without the need to switch the chilled water system.

Air conditioning↗
DOE OSTI2017

From aggregative adsorption to surface depletion: Aqueous systems of C n E m amphiphiles at hydrophilic surfaces

Adsorption of a short-chain nonionic amphiphile (C 6 E 3 ) at the surface of mesoporous silica glass (CPG-10) was studied by a combination of adsorption measurements and mesoscale simulations. Adsorption measurements covering a wide composition range of the C 6 E 3 + water system show that no adsorption occurs up to the critical micelle concentration (cmc), at which a sharp increase of adsorption is observed that is attributed to ad-micelle formation at the pore walls. Intriguingly, as the concentration is increased further, the surface excess of the amphiphile begins to decrease and eventually becomes negative, which corresponds to preferential adsorption of water rather than amphiphile at high amphiphile concentrations. The existence of such a surface-azeotropic point has not previously been reported in the surfactant adsorption field. Dissipative particle dynamics (DPD) simulations were performed to reveal the structural origin of this transition from aggregative adsorption to surface depletion. Finally, the simulations indicate that this transition can be attributed to the repulsive interaction between head groups, causing amphiphilic depletion in the region around the corona of the surface micelles.

36 MATERIALS SCIENCE↗
DOE OSTI2018

EPA and Idaho National Laboratory create first of its scale

Advancing the science and engineering of decontaminating water distribution systems and safely disposing of high-volumes of contaminated water are high priorities for the EPA. To help address these science gaps, EPA homeland security researchers have developed the first-of-its-scale Water Security Test Bed (WSTB). Water is an important component of everyday life. We rely on safe, clean water for our health and the health of the environment. Protecting this vital resource is critical to living safely and securely. The U.S. Environmental Protection Agency is responsible for working with water utilities to protect water systems from contamination and to clean up systems that become contaminated. Purposeful or inadvertent distribution system contamination can result in large amounts of infrastructure and water that must be cleaned. Water distribution systems contamination can be caused by, for example, natural disasters such as Superstorm Sandy or by individuals hoping to cause harm. The WSTB, constructed at the Department of Energy’s (DOE) Idaho National Laboratory, replicates a section of a typical municipal drinking water system including a piping system with roughly 445 feet of pipe and two fire hydrants laid out in an “L” shape using 40-year-old, eight-inch cement mortar lined, ductile iron pipes, excavated after twenty years of use for water conveyance. Researchers built the WSTB above ground for easy access during experiments, and to facilitate fast leak detection. Over the next several years, EPA and partner researchers will conduct experiments using simulants of various biological, chemical, and radioactive materials that simulate high toxic versions of these agents. At this “full” sized system, researchers will demonstrate approaches to contamination detection, sensor and model testing, infrastructure decontamination, water treatment and cyber testing developed at lab and pilot scale. Researchers are also able to verify if laboratory results that were effective in controlled conditions are as effective in full-scale testing. Having the ability to conduct bench scale studies in a real world setting can help address specific research gaps, and help water researchers understand conditions in which real world drinking water systems operate.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Department of Energy/IDEA: More best-practices research

This article continues the overview of the U.S. Department of Energy and IDEA collaboration by highlighting additional case studies that demonstrate innovative engineering approaches in district energy systems. It focuses on how campuses are improving efficiency, integrating advanced technologies, and reducing energy use and emissions through data-driven strategies. The University of Cincinnati is featured for its highly efficient chilled water system, using advanced algorithms and upgraded “smart chillers” to optimize performance, reduce energy consumption, and lower costs. Wake Forest University emphasizes a data-informed modernization process, using system optimization and targeted building improvements to significantly boost efficiency and reduce overall energy use. Arizona Western College showcases creative solutions to extreme cooling demands, including system redesign, smart controls, and thermal storage to improve reliability and cut peak energy costs. Overall, the article demonstrates that combining innovative engineering, real-time data analysis, and system optimization can significantly enhance performance, reduce emissions, and deliver cost savings in district energy systems.

96 KNOWLEDGE MANAGEMENT AND PRESERVATION↗
NASA NTRS1999

Bubble Generation in a Flowing Liquid Medium and Resulting Two-Phase Flow in Microgravity

The present investigation reports a study of bubble generation under reduced gravity conditions, using both a co-flow and a cross-flow configuration. This study may be used in the conceptual design of a space-based thermal management system. Ensuing two-phase flow void fraction can be accurately monitored using a single nozzle gas injection system within a continuous liquid flow conduit, as utilized in the present investigation. Accurate monitoring of void fraction leads to precise control of heat and mass transfer coefficients related to a thermal management system; hence providing an efficient and highly effective means of removing heat aboard spacecraft or space stations. Our experiments are performed in parabolic flight aboard the modified DC-9 Reduced Gravity Research Aircraft at NASA Lewis Research Center, using an air-water system. For the purpose of bubble dispersion in a flowing liquid, we use both a co-flow and a cross-flow configuration. In the co-flow geometry, air is introduced through a nozzle in the same direction with the liquid flow. On the other hand, in the cross-flow configuration, air is injected perpendicular to the direction of water flow, via a nozzle protruding inside the two-phase flow conduit. Three different flow conduit (pipe) diameters are used, namely, 1.27 cm, 1.9 cm and 2.54 cm. Two different ratios of nozzle to pipe diameter (D(sub N))sup * are considered, namely (D(sub N))sup * = 0.1 and 0.2, while superficial liquid velocities are varied from 8 to 70 cm/s depending on flow conduit diameter. It is experimentally observed that by holding all other flow conditions and geometry constant, generated bubbles decrease in size with increase in superficial liquid velocity. Detached bubble diameter is shown to increase with air injection nozzle diameter. Likewise, generated bubbles grow in size with increasing pipe diameter. Along the same lines, it is shown that bubble frequency of formation increases and hence the time to detachment of a forming bubble decreases, as the superficial liquid velocity is in-creased. Furthermore, it is shown that the void fraction of the resulting two-phase flow increases with volumetric gas flow rate Q(sub d), pipe diameter and gas injection nozzle diameter, while they decrease with surrounding liquid flow. The important role played by flowing liquid in detaching bubbles in a reduced gravity environment is thus emphasized. We observe that the void fraction can be accurately controlled by using single nozzle gas injection, rather than by employing multiple port injection, since the later system gives rise to unpredictable coalescence of adjacent bubbles. It is of interest to note that empirical bubble size and corresponding void fraction are somewhat smaller for the co-flow geometry than the cross-flow configuration at similar flow conditions with similar pipe and nozzle diameters. In order to supplement the empirical data, a theoretical model is employed to study single bubble generation in the dynamic (Q(sub d) = 1 - 1000 cu cm/s) and bubbly flow regime within the framework of the co-flow configuration. This theoretical model is based on an overall force balance acting on the bubble during the two stages of generation, namely the expansion and the detachment stage. Two sets of forces, one aiding and the other inhibiting bubble detachment are identified. Under conditions of reduced gravity, gas momentum flux enhances, while the surface tension force at the air injection nozzle tip inhibits bubble detachment. In parallel, liquid drag and inertia can act as both attaching and detaching forces, depending on the relative velocity of the bubble with respect to the surrounding liquid. Predictions of the theoretical model compare well with our experimental results. However, at higher superficial liquid velocities, as the bubble loses its spherical form, empirical bubble size no longer matches the theoretical predictions. In summary, we have developed a combined experimental and theoretical work, which describes the complex process of bubble generation and resulting two-phase flow in a microgravity environment. Results of the present study can be used in a wide range of space-based applications, such as thermal energy and power generation, propulsion, cryogenic storage and long duration life support systems, necessary for programs such as NASA's Human Exploration for the Development of Space (HEDS).

Pais, S. C.↗
DOE OSTI2024

Electrochemical reduction of per- and polyfluorinated alkyl substances (PFAS): is it possible? Applying experimental and quantum mechanical insights from the reductive defluorination literature

Remediation of per- and polyfluorinated alkyl substances (PFAS) in global water systems is a critical human and environmental health challenge facing society. PFAS consumption is associated with a litany of adverse health effects, and our knowledge of these dangers is still evolving. Current techniques to remove PFAS from water include adsorption to media (e.g. granular activated carbon, ion-exchange resin), nanofiltration, and reverse osmosis. However, these processes create a concentrated PFAS residual that requires further management. Destructive techniques are therefore needed to detoxify these residuals. Oxidative techniques have garnered the most attention (e.g. supercritical water oxidation, electrochemical oxidation) but are energy intensive and potentially form toxic by-products. As an alternative, several groups have researched advanced reduction processes that form aqueous electrons, but these processes are still chemical and energy intensive (e.g. ultraviolet/SO 3 2− , electron beam). This concise review therefore focuses on whether electrochemical reduction — a chemical-free, modular process — could be technically feasible for PFAS destruction.

King, Jacob F.↗
DOE OSTI2017

Subtle Effects of Aliphatic Alcohol Structure on Water Extraction and Solute Aggregation in Biphasic Water/ n -Dodecane

Organic phase aggregation behavior of 1-octanol and its structural isomer, 2-ethylhexanol, in a biphasic n-dodecane water system is studied with a combination of physical measurement, small-angle X-ray scattering (SAXS), and atomistic molecular dynamic simulations. Physical properties of the organic phases are probed following their mixing and equilibration with immiscible water phases. Studies reveal that the interfacial tension decreases as a function of increasing alcohol concentration over the solubility range of the alcohol with no evidence for a critical aggregate concentration (cac). An uptake of water into the organic phases is quantified, as a function of alcohol content, by Karl Fischer titrations. The extraction of water into dodecane was further assessed as a function of alcohol concentration via the slope-analysis method sometimes employed in chemical separations. This provides a qualitative understanding of solute (water/alcohol) aggregation in the organic phase. The physical results are supported by analyses of SAXS data that reveals an emergence of aggregates in n-dodecane at elevated alcohol concentrations. The observed aggregate structure is dependent on the alcohol tail group geometry, consistent with surfactant packing parameter. The formation of these aggregates is discussed at a molecular level, where alcohol-alcohol and alcohol-water H-bonding interactions likely dominate the occurrence and morphology of the aggregates.

Knight, Andrew W.↗
DOE OSTI2022

Water use in a young Pinus taeda bioenergy plantation: Effect of intensive management on stand evapotranspiration

Abstract The increasing demand for plant‐derived bioenergy is projected to expand tree plantations with intensive silviculture and improved tree genetics. These silvicultural practices result in faster stand development and canopy closure, which may also influence the systems' water dynamics. Here, we studied the evapotranspiration (ET) of a young (5 years old) intensively managed loblolly pine ( Pinus taeda ) stand and investigated the components of ET to determine its contribution to overall water use. We also compared ET with plantations that received less intensive management to determine whether our stand used more water. We used the eddy covariance method to estimate ecosystem‐level total ET (ET EC ), while plot‐level estimates of ET (ET P ) were obtained via soil lysimeters, sap flow sensors, and throughfall collectors, enabling measurement of the components of ET. Soil evaporation (Es) was the largest component of ET P (36%) over the course of the study, while transpiration and canopy interception accounted for 27% and 22%, respectively. Es decreased with stand development, while transpiration and canopy interception increased. Leaf area index (LAI) and precipitation were the most significant factors controlling ET and its components. Compared to previous studies in different sites that have similar age but lower LAI, our stand had higher water use. This high water use in the early stages of stand development was primarily due to high Es before the canopy was fully developed. While there are potential sources of uncertainty when comparing ET EC and the component fluxes in ET P , results from the two methods were not significantly different. This study had the advantage of using multiple methods to understand and verify the component processes that contribute to ET. Therefore, we recommend that multiple measurement techniques be used in the long‐term observation of ET, and in particular for the evaluation of the impact that intensively managed forests have on water resources in the southeastern United States.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2018

Data Driven Temperature Control of Heat Exchangers

The following poster presents a couple of approaches for temperature control at heat exchanger’s exit. One of the approaches is based on using n-step ahead neural network while the other approach utilizes a combination of control + learning module for temperature control. Designing robust controllers for typical heat exchangers is very challenging primarily because of complexities associated with the synthesis of dynamics of industrial heat exchangers. Even if a dynamics model is synthesized, the accuracy of it would be called into question as there can be lot of unmodeled system dynamics and random noise in input parameters. In many situations, the degree of uncertainty in the model of system being controlled limits the utility of optimal control design. Controller can be manually tuned on the field but it is very difficult to determine manual adjustments that result in overall improvement. These practical challenges call for learning based approaches for temperature control that would result in optimal heat exchanger performance. We utilize the existing mathematical model for air-water system synthesized by Underwood and Crawford for testing our algorithms. Underwood and Crawford developed a model of heating coil by fitting a second-order non-linear equations to measurements of air and water temperature and flow rates obtained from the actual coil. The uncertainties in the model include air and water inlet temperatures and air-flow rate. These uncertainties are modeled as random variables that are sampled from a uniform distribution. The control variable is the water flow rate which is controlled for regulating the air-outlet temperature. Neural networks are frequently used in various literatures for learning time-series. We propose a modified version of neural networks known as n-step ahead neural network that take the state variables and output at time t as input to successfully predict output at time t+n. The variable n is a hyper-parameter which can be optimized based on performance constraints. The n-step ahead neural network was then trained on training data generated from experimental model to high training accuracies. This trained model performed appreciably in its objective to regulate outlet temperature of a heat exchanger. The second approach uses a combination of control and learning module for temperature regulation. The control module used is a proportional controller while the learning module used is steady state neural network. The steady state neural network is used to learn the controller output as a function of random variables and temperature set-point. The proportional controller is then used to compensate for transient behavior of linearized system around various operating points. The algorithm works effectively for temperature regulation as neural network captures the non-linear input-output behavior of closed loop system leaving proportional controller to compensate for steady state errors of a linearized plant. The proposed algorithm’s performances were evaluated against the performance of a PI controller. Further, the robustness of the algorithms were also studied in great detail under small perturbations around tuned parameters of the proposed algorithms.

Sundar, Sreenath↗
DOE OSTI2023

Solution Structure and Hydration Forces between Mica and Hydrophilic Versus Hydrophobic Surfaces

Solid-liquid interfaces are central to a range of interesting phenomena including catalysis, heterogeneous nucleation, water desalination, and biomolecular assembly. While three-dimensional Fast Force Mapping (3D FFM) has emerged as a technique for resolving interfacial solution structure at the molecular scale, key challenges for data interpretation persist, most notably regarding the influence of the probe on the measured structure. Using the mica-water system as a case study, we investigate the effect of hydrophilic and hydrophobic probes on interfacial solution structure measured by 3D FFM. Data from hydrophilic silicon-based probes are in good agreement with molecular dynamics simulations, wherein the innermost water molecules adsorb preferentially at the surface ditrigonal cavity sites followed by two subsequent hydration layers. In contrast, the hydrophobic carbon-based probes detect vertical oscillatory features, but do not show lateral patterning that matches the underlying mica lattice. At high ionic strength, up to six of these oscillatory features are observed extending 2 nm into the solution phase with an average spacing of 0.29 ± (0.04) nm. Further, we also determine that the repulsive hydration force between mica and the hydrophilic probe depends on the nature and concentration of ions in solution. Specifically, solutions with stronger ion-water and ion-ion interactions increase the interfacial viscosity, which results in a stronger repulsive hydration force as the probe approaches the surface. Based on these observations, we present a scheme for controlling the outcomes of particle attachment and aggregation by varying the solution conditions to tune the hydration force.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Machine learning coarse grained models for water

An accurate and computationally efficient molecular level description of mesoscopic behavior of ice-water systems remains a major challenge. Here, we introduce a set of machine-learned coarse-grained (CG) models (ML-BOP, ML-BOP dih , and ML-mW) that accurately describe the structure and thermodynamic anomalies of both water and ice at mesoscopic scales, all at two orders of magnitude cheaper computational cost than existing atomistic models. In a significant departure from conventional force-field fitting, we use a multilevel evolutionary strategy that trains CG models against not just energetics from first-principles and experiments but also temperature-dependent properties inferred from on-the-fly molecular dynamics (~ 10’s of milliseconds of overall trajectories). Our ML BOP models predict both the correct experimental melting point of ice and the temperature of maximum density of liquid water that remained elusive to-date. Our ML workflow navigates efficiently through the high-dimensional parameter space to even improve upon existing high-quality CG models (e.g. mW model).

42 ENGINEERING↗
DOE OSTI2019

Agrivoltaics provide mutual benefits across the food–energy–water nexus in drylands

The vulnerabilities of our food, energy and water systems to projected climatic change make building resilience in renewable energy and food production a fundamental challenge. We investigate a novel approach to solve this problem by creating a hybrid of colocated agriculture and solar photovoltaic (PV) infrastructure. We take an integrative approach - monitoring microclimatic conditions, PV panel temperature, soil moisture and irrigation water use, plant ecophysiological function and plant biomass production within this 'agrivoltaics' ecosystem and in traditional PV installations and agricultural settings to quantify trade-offs. We find that shading by the PV panels provides multiple additive and synergistic benefits, including reduced plant drought stress, greater food production and reduced PV panel heat stress. The results presented here provide a foundation and motivation for future explorations towards the resilience of food and energy systems under the future projected increased environmental stress involving heat and drought.

14 SOLAR ENERGY↗