Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WIND TUNNELS - FIRST”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Low and high speed propellers for general aviation: Performance potential and recent wind tunnel test results

The performance of lower speed, 5 foot diameter model general aviation propellers, was tested in the Lewis wind tunnel. Performance was evaluated for various levels of airfoil technology and activity factor. The difference was associated with inadequate modeling of blade and spinner losses for propellers round shank blade designs. Suggested concepts for improvement are: (1) advanced blade shapes (airfoils and sweep); (2) tip devices (proplets); (3) integrated propeller/nacelles; and (4) composites. Several advanced aerodynamic concepts were evaluated in the Lewis wind tunnel. Results show that high propeller performance can be obtained to at least Mach 0.8.

Jeracki, R. J.↗

Comparison of model- and full-scale wind-tunnel performance

Experimental results from the Integrated Systems Test of the upgraded National Full-Scale Aerodynamics Complex 40- by 80-ft wind tunnel located at NASA Ames Research Center, which took place in 1987, are compared with results obtained with a 1/50 scale model of the wind tunnel. Test-section flow characteristics, air-exchange performance, total pressure distributions, and wall-static pressure distributions obtained with the model- and full-scale facilities are compared. The 1/50-scale model data were used to predict qualitative performance trends of the full-scale facility during investigation of design changes. Despite large differences in scale and Reynolds number between the two tunnels, quantitative agreement between certain model and full-scale performance characteristics was quite good.

Smith, Brian E.↗

Finite Element Analysis of a NASA National Transonic Facility Wind Tunnel Balance

This paper presents the results of finite element analyses and correlation studies performed on a NASA National Transonic Facility (NTF) Wind Tunnel balance. In the past NASA has relied primarily on classical hand analyses, coupled with relatively large safety factors, for predicting maximum stresses in wind tunnel balances. Now, with the significant advancements in computer technology and sophistication of general purpose analysis codes, it is more reasonable to pursue finite element analyses of these balances. The correlation studies of the present analyses show very good agreement between the analyses and data measured with strain gages and therefore the studies give higher confidence for using finite element analyses to analyze and optimize balance designs in the future.

Lindell, Michael C.↗

Exploratory low-speed wind-tunnel investigation of advanced commuter configurations including an over-the-wing propeller design

A recent low-speed wind-tunnel investigation of a three-surface regional transport configuration has shown large favorable power effects on longitudinal and lateral stability and marginal engine-out trim characteristics for some aft engine and empennage configurations. The present paper discusses these results in terms of static force test information obtained for power-off and power-on conditions. Also discussed in this paper are wind-tunnel results which indicate that mounting propellers over the wing can introduce large favorable slipstream interference effects which significantly reduce the wing drag at climb power conditions.

Johnson, J. L., Jr.↗

Supersonic Aftbody Closure Wind-Tunnel Testing, Data Analysis, and Computational Results

This paper reports on the model, test, and results from the Langley Supersonic Aftbody Closure wind tunnel test. This project is an experimental evaluation of the 1.5% Technology Concept Aircraft (TCA) aftbody closure model (Model 23) in the Langley Unitary Plan Wind Tunnel. The baseline TCA design is the result of a multidisciplinary, multipoint optimization process and was developed using linear design and analysis methods, supplemented with Euler and Navier-Stokes numerical methods. After a thorough design review, it was decided to use an upswept blade attached to the forebody as the mounting system. Structural concerns dictated that a wingtip support system would not be feasible. Only the aftbody part of the model is metric. The metric break was chosen to be at the fuselage station where prior aft-sting supported models had been truncated. Model 23 is thus a modified version of Model 20. The wing strongback, flap parts, and nacelles from Model 20 were used, whereas new aftbodies, a common forebody, and some new tails were fabricated. In summary, significant differences in longitudinal and direction stability and control characteristics between the ABF and ABB aftbody geometries were measured. Correcting the experimental data obtained for the TCA configuration with the flared aftbody to the representative of the baseline TCA closed aftbody will result in a significant reduction in longitudinal stability, a moderate reduction in stabilizer effectiveness and directional stability, and a moderate to significant reduction in rudder effectiveness. These reductions in the stability and control effectiveness levels of the baseline TCA closed aftbody are attributed to the reduction in carry-over area.

Allen, Jerry↗

Wind-Tunnel Overpressure Signatures From a Low-Boom HSCT Concept With Aft-Fuselage-Mounted Engines

A 1:300 scale wind-tunnel model of a conceptual High-Speed Civil Transport (HSCT) designed to generate a shaped, low-boom pressure signature on the ground was tested to obtain sonic-boom pressure signatures in the Langley Research Center Unitary Plan Wind Tunnel at a Mach number of 1.8 and a separation distance of about two body lengths or four wing-spans from the model. Two sets of engine nacelles representing two levels of engine technology were used on the model to determine the effects of increased nacelle volume. Pressure signatures were measured for (model lift)/(design lift) ratios of 0.5, 0.63, 0.75, and 1.0 so that the effect of lift on the pressure signature could be determined. The results of these tests were analyzed and used to discuss the agreement between experimental data and design expectations.

Mack, Robert J.↗

On-line analysis capabilities developed to support the AFW wind-tunnel tests

A variety of on-line analysis tools were developed to support two active flexible wing (AFW) wind-tunnel tests. These tools were developed to verify control law execution, to satisfy analysis requirements of the control law designers, to provide measures of system stability in a real-time environment, and to provide project managers with a quantitative measure of controller performance. Descriptions and purposes of the developed capabilities are presented along with examples. Procedures for saving and transferring data for near real-time analysis, and descriptions of the corresponding data interface programs are also presented. The on-line analysis tools worked well before, during, and after the wind tunnel test and proved to be a vital and important part of the entire test effort.

Wieseman, Carol D.↗

MHz-Rate NO PLIF Imaging in a Mach 10 Hypersonic Wind Tunnel

NO PLIF imaging at repetition rates as high as 1 MHz is demonstrated in the NASA Langley 31 inch Mach 10 hypersonic wind tunnel. Approximately two hundred time correlated image sequences, of between ten and twenty individual frames, were obtained over eight days of wind tunnel testing spanning two entries in March and September of 2009. The majority of the image sequences were obtained from the boundary layer of a 20 flat plate model, in which transition was induced using a variety of cylindrical and triangular shaped protuberances. The high speed image sequences captured a variety of laminar and transitional flow phenomena, ranging from mostly laminar flow, typically at lower Reynolds number and/or in the near wall region of the model, to highly transitional flow in which the temporal evolution and progression of characteristic streak instabilities and/or corkscrew-shaped vortices could be clearly identified. A series of image sequences were also obtained from a 20 compression ramp at a 10 angle of attack in which the temporal dynamics of the characteristic separated flow was captured in a time correlated manner.

Jiang, N.↗

Analysis of holographic interferograms of aerodynamic models in a wind tunnel

Holographic interferometry provides a non-invasive technique for estimating variations in the air density distribution around aerodynamic models in wind tunnels. The testing of this technique has been underway for some time and has been reported previously for a two dimensional aerodynamic model. Results obtained from tests using three dimensional aerodynamic models are summarized. Holograms were made of aerodynamic models in a wind tunnel. Interferograms were made from these holograms. The interference fringes in these holographic interferograms were digitized and this information was entered into the HOLOFT program. The HOLOFT program successfully calculated the known stagnation air density at the nose of a model and the known air density distribution across the cross section passing through the stagnation point for the axisymmetrical case of this model at a Mach number of 0.8. Thus the technique of holographic interferometry does work.The HOLOFT program stands for HOLOgraphic Inversion by 2-D Fourier Transform.

Perry, R. L.↗

Space shuttle: A comparison of wind tunnel facility data on the 040A space shuttle orbiter configuration

A series of comparisons made on the longitudinal and lateral directional stability and control characteristics of the baseline 040A space shuttle orbiter configuration is documented. The data used for the comparisons were obtained from five wind tunnel tests conducted in four different wind tunnel facilities. The media for comparison were the aerodynamic slope values plotted as a function of Mach number for the different facilities. The slopes were computed using the SADSAC system and have been reduced relative to a common reference system. Data used for the comparison were selected based on a common baseline configuration. Identical configurations were available in all cases except MSFC 551 where an off-baseline vertical tail was tested. Some of the factors considered in comparing the various data were balance operating ranges and sensitivities, Reynolds number differences, scaling effects and control deflection accuracies.

Gyorfi, R. A.↗

Wind Tunnel PSD and MVD Characterization Using New 1D2D Optical Array Probes

This work explores characterization of the liquid clouds using a combination of a forward scattering probe and two Optical Array Probes. Current OAP probes provide particle shape, size, and number concentration from two-dimensional shadow images. However, past studies have shown that such images are subject to distortion when outside of the focal plane. This affects the retrieval of particle size distributions, particularly in the Supercooled Large Droplet size range. In this article, the use of a Droplet Measurement Technologies Cloud Droplet Probe and two new OAPs produced by Science Engineering Associates, is examined using wind tunnel data, to assess suitability for use in a wind tunnel calibration in SLD conditions. The new OAP probes exploit a flexible and simple grey scale imaging method to eliminate some present shortcomings of commonly used OAPs, and to reduce correction factors. Spinning disk measurements were used to specify probe depth of field, and average size errors. Composite spectra covering the nominal 2-3200 µm size range were formed by crossing over from the CDP to 1D2D-X at 48 µm, and then to the 1D2D-Y at about 400 µm. A good overlap was found at the crossover points without any artificial scaling. Composite spectra adequately closed the liquid water content distribution, and provided integrated LWCs within about 35% of the hot-wire LWCs used for tunnel calibration. This discrepancy was at least partially attributed to LWC underestimation by the hot-wire at high MVD. A model of probe performance was used to show an example of expected accuracy of ideal probes subject to the same OAP distortions and using the same mitigating procedures and corrections, predicting PSD Median Volume Diameter and integrated LWC errors of less than 10%.

Aircraft Icing↗

Analysis of F/A-18 Tail Buffet Data Acquired in the 80- by 120-Foot Wind Tunnel

Tail buffet studies were conducted on a full-scale, production, F/A-18 fighter aircraft in the 80- by 120-Foot Wind Tunnel of the National Full-Scale Aerodynamic Complex at NASA Ames Research Center at Moffett Field, California. Tail buffet data were acquired over an angle-of-attack range of +20 deg to +40 deg, a side-slip range of -16 deg to + 16 deg, and at wind speeds up to 100 knots. The maximum speed corresponds to a Reynolds number of l2.3 x l0(exp 6) based on mean aerodynamic chord and a Mach number of 0. 15. The port, vertical tail fin was instrumented with ninety-six surface-pressure transducers, arranged in six by eight arrays, on each side of the fin. ne aircraft was also equipped with a removable Leading-Edge Extension (LEX) fence whose purpose is to reduce tail-buffet loads. Current analysis methods for the unsteady aerodynamic pressures and loads are described. Only results for the zero side-slip condition are to be presented, both with and without the LEX fence. Results of the time-averaged, power-spectral analysis are presented for the tail fin bending moments which are derived from the integrated pressure field. Local wave velocities on the tail surfaces are calculated from pressure correlations. It was found that the LEX fence significantly reduces the magnitude of the root-mean-square pressures and bending moments. Scaling and repeatability issues are addressed by comparing the present full scale results for pressures at the 60%-span and 45%-chord location with previous full-scale F/A-18 tail-buffet test in the 80- by 120- Foot Wind Tunnel, and with several small-scale tests. The comparisons show that the tail buffet frequency scales very well with tail chord and free-stream velocity, and that there is good agreement with the previous full-scale test. Root-mean-square pressures and power spectra do not scale as well as the frequency results. Addition of a LEX fence caused tail-buffet loads to be reduced at all model scales.

James, Kevin D.↗

Wind-tunnel measurements and comparison with flight of the boundary layer and heat transfer on a hollow cylinder at Mach 3

The wind tunnel tests were conducted both with and without boundary layer trips at Mach 3 and nominal free stream Reynolds numbers per meter ranging from 3.3 x 10 the 6th power. Instrumentation consisted of pressure orifices, thermocouples, a boundary layer pitot pressure rake, and a floating element skin friction balance. Measurements from both wind tunnel and flight were compared with existing engineering prediction methods.

Stallings, R. L., Jr.↗