Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “WHEELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Numerical and experimental analysis of precooled desiccant system

This paper presents a numerical and experimental study of four novel, desiccant air-conditioning systems based on pre-cooling of the ambient air. The purpose of the study is to: 1) establish which configuration is most profitable for the future studies through numerical and experimental methods; 2) verify the concept of precooled system and confirm that it is working in experimental conditions (for this purpose two prototypes of evaporative cooling units were developed and compared for different operation arrangements with desiccant wheel); 3) Analyze practical aspects of the systems, which includes water consumption analysis, economic analysis and establishing operational modes during a cooling season in temperate climate conditions (the proposed solution has a significant advantage during operation in a temperate climate, since it can utilize its first evaporative cooler the only source of cooling energy when the humidity of outdoor air allows to to meet the latent cooling load). Four arrangements of the system with different dew point evaporative air cooler prototypes were selected and developed for comparative analysis. The system was simulated as a whole, also, each component was individually tested on measurement station. develop the optimal arrangement of the system through numerical and experimental analysis. Four different performance indicators were considered: thermal COP (Coefficient Of Performance), the ERR (Energy Efficiency Ratio), coefficient a describing the potential in compensating indoor cooling loads, water consumption ratio. Also costs of the systems were compared through economic analysis. It was established that arrangement which is characterized by best-averaged performance in terms of all considered factors is a unit combined with two different types of evaporative coolers (marked as System B)- this is caused by the favorable arrangement of two units, where one is better suited to the pre-cooler role, while the other is better suited as the post-cooler.

42 ENGINEERING↗

A methodology for selection of solid desiccants in energy recovery ventilators

Controlling indoor humidity levels is essential for maintaining acceptable indoor air quality in buildings. The use of energy recovery ventilators (ERVs) is an energy-efficient way to regulate indoor air humidity. Fixed-bed regenerators and rotary wheels are widely used ERVs because of their high sensible and latent effectiveness. These ERVs are made of desiccant-coated substrates, which enable them to transfer moisture between the supply and exhaust air streams. However, the moisture transfer ability of ERVs depends on the physiochemical and sorption properties of desiccants. Extensive, full-scale experiments are required to determine the best desiccant material for these systems. This paper presents a simplified method of selecting suitable desiccant materials for ERVs. The methodology involves important characterization methods, literature correlations for performance prediction, and cost-effective testing methods prior to full-scale testing, and full-scale test methods are discussed in detail. Furthermore, the performance of a few newly derived materials is evaluated and compared with that of conventional desiccants such as silica gel and molecular sieves. The highest latent effectiveness was obtained for composite of super absorbent polymer (SAP) with potassium formate (SAP-HCO2K-50 %), all-polymer porous solid desiccant (APPSD) and metal organic framework (MOF)–MIL–101 (Cr), followed by activated carbon fibre felt (ACFF) Silica sol-LiCl30, SAP, silica gel, MOF–303, and molecular sieve. Researchers and manufacturers would benefit from the proposed methodology and presented data in developing new desiccant materials for ERV applications.

Energy recovery↗

On the validity and limitations of 1D model for heat and mass transfer performance evaluation in a multilayer binder-free desiccant dehumidifier: isothermal dehumidification with internal cooling

Efficient humidity control is essential for maintaining indoor thermal comfort, yet conventional vapor-compression-based dehumidifiers are energy-intensive. Employing separate sensible and latent cooling through desiccant-coated heat exchangers (DCHEs) combined with evaporative coolers offers energy savings of up to 80 % compared to conventional systems. However, the dehumidification performance of DCHEs remains limited due to the use of polymer binders for coating desiccant materials onto heat exchange surfaces. In our previous study, we developed a multilayer fixed-bed binder-free desiccant dehumidifier (MFBDD) that demonstrated high dehumidification capacity and low pressure drop compared to rotary desiccant wheels. Nevertheless, its potential for further enhancement through internal cooling and the use of step-shaped adsorption isotherms has not been explored. In this study, a physics-based one-dimensional (1D) transient model is developed and validated to capture the coupled heat and mass transfer processes in the MFBDD and extended to simulate internal cooling using a high-capacity composite metal–organic framework, MIL-101/GO-6 (water uptake ≈1.6 g/g within 35–47 % RH). The model enables detailed analysis of local air and bed temperature dynamics and quantifies how internal cooling affects the dehumidification performance under a wide range of operating conditions. Results show that integrating internal cooling and using MIL-101/GO-6 enhance mass adsorbed, moisture removal capacity, and dehumidification effectiveness by 50 %–99 % compared with the M.S. Gel baseline. The study further reveals that achieving near-isothermal operation requires simultaneous enhancement of the convective heat transfer coefficient and heat exchange surface area. In conclusion, this work provides the first detailed physical insight into the interplay between internal cooling and step-shaped isotherms in a binder-free desiccant device and establishes a validated modeling framework for scaling up and system-level performance evaluation of next-generation energy-efficient dehumidification systems.

Heat and mass transfer↗

Effect of cathode shape on vertical buffered electropolishing for niobium SRF cavities

This paper reports the research results of the effect of cathode shape during vertical buffered electropolishing (BEP) by employing a demountable single cell niobium (Nb) superconducting radio frequency (SRF) cavity. Several different cathode shapes such as, for instance, bar, ball, ellipsoid, and wheels of different diameters have been tested. Detailed electropolishing parameters including I–V characteristic, removal rate, surface roughness, and polishing uniformity at different locations inside the demountable cavity are measured. Similar studies are also done on conventional electropolishing (EP) for comparison. It is revealed that cathode shape has dominant effects for BEP especially on the obtaining of a suitable polishing condition and a uniform polishing rate in an Nb SRF single cell cavity. EP appears to have the same tendency. This paper demonstrates that a more homogeneous polishing result can be obtained by optimizing the electric field distribution inside the cavity through the modification of the cathode shape given the conditions that temperature and electrolyte flow are kept constant. Electric field distribution and electrolyte flow patterns inside the cavity are simulated via Poisson–Superfish and Solidworks respectively. Finally, with the optimal cathode shape, BEP shows a much faster polishing rate of ~2.5 μm/min and is able to produce a smoother surface finish in the treatments of single cell cavities in comparison with EP.

36 MATERIALS SCIENCE↗

Forced running exercise attenuates hippocampal neurogenesis impairment and the neurocognitive deficits induced by whole-brain irradiation via the BDNF-mediated pathway

Highlights: •Forced exercise can ameliorate WBI induced cognitive impairment in our rat model. •Mature BDNF plays an important role in the effects of forced exercise. •Exercise may be a possible treatment of the radiation-induced cognitive impairment. -- Abstract: Cranial radiotherapy induces progressive and debilitating cognitive deficits, particularly in long-term cancer survivors, which may in part be caused by the reduction of hippocampal neurogenesis. Previous studies suggested that voluntary exercise can reduce the cognitive impairment caused by radiation therapy. However, there is no study on the effect of forced wheel exercise and little is known about the molecular mechanisms mediating the effect of exercise. In the present study, we investigated whether the forced running exercise after irradiation had the protective effects of the radiation-induced cognitive impairment. Sixty-four Male Sprague–Dawley rats received a single dose of 20 Gy or sham whole-brain irradiation (WBI), behavioral test was evaluated using open field test and Morris water maze at 2 months after irradiation. Half of the rats accepted a 3-week forced running exercise before the behavior detection. Immunofluorescence was used to evaluate the changes in hippocampal neurogenesis and Western blotting was used to assess changes in the levels of mature brain-derived neurotrophic factor (BDNF), phosphorylated tyrosine receptor kinase B (TrkB) receptor, protein kinase B (Akt), extracellular signal-regulated kinase (ERK), calcium-calmodulin dependent kinase (CaMKII), cAMP-calcium response element binding protein (CREB) in the BDNF–pCREB signaling. We found forced running exercise significantly prevented radiation-induced cognitive deficits, ameliorated the impairment of hippocampal neurogenesis and attenuated the down-regulation of these proteins. Moreover, exercise also increased behavioral performance, hippocampal neurogenesis and elevated BDNF–pCREB signaling in non-irradiation group. These results suggest that forced running exercise offers a potentially effective treatment for radiation-induced cognitive deficits.

60 APPLIED LIFE SCIENCES↗

Voluntary running suppresses tumor growth through epinephrine- and IL-6-dependent NK cell mobilization and redistribution

Regular exercise reduces the risk of cancer and disease recurrence. Yet the mechanisms behind this protection remain to be elucidated. In this study, tumor-bearing mice randomized to voluntary wheel running showed over 60% reduction in tumor incidence and growth across five different tumor models. Microarray analysis revealed training-induced up-regulation of pathways associated with immune function. NK cell infiltration was significantly increased in tumors from running mice, whereas depletion of NK cells enhanced tumor growth and blunted the beneficial effects of exercise. Mechanistic analyses showed that NK cells were mobilized by epinephrine, and blockade of beta-adrenergic signaling blunted training-dependent tumor inhibition. Moreover, epinephrine induced a selective mobilization of IL-6-sensitive NK cells, and IL-6-blocking antibodies blunted training-induced tumor suppression, intratumoral NK cell infiltration, and NK cell activation. Altogether, these results link exercise, epinephrine, and IL-6 to NK cell mobilization and redistribution, and ultimately to control of tumor growth.

59 BASIC BIOLOGICAL SCIENCES↗

Experimental investigation on flame pattern formations of DME-air mixtures in a radial microchannel

Flame pattern formations of premixed DME-air mixture in a heated radial channel with a gap distance of 2.5 mm were experimentally investigated. The DME-air mixture was introduced into the radial channel through a delivery tube which connected with the center of the top disk. With an image-intensified high-speed video camera, rich flame pattern formations were identified in this configuration. Regime diagram of all these flame patterns was drawn based on the experimental findings in the equivalence ratio range of 0.6-2.0 and inlet velocity range of 1.0-5.0 m/s. Compared with our previous study on premixed methane-air flames, there are several distinct characteristics for the present study. First, Pelton-wheel-like rotary flames and traveling flames with kink-like structures were observed for the first time. Second, in most cases, flames can be stabilized near the inlet port of the channel, exhibiting a conical or cup-like shape, while the conventional circular flame was only observed under limited conditions. Thirdly, an oscillating flame phenomenon occurred under certain conditions. During the oscillation process, a target appearance was seen at some instance. These pattern formation characteristics are considered to be associated with the low-temperature oxidation of DME. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Comparing total cost of ownership of battery electric vehicles and internal combustion engine vehicles

The technological advance of electrochemical energy storage and the electric powertrain has led to rapid growth in the deployment of electric vehicles. The high cost and the added weight of the batteries have limited the size (energy storage capacity) and, therefore, the driving range of these vehicles. However, consumers are steadily purchasing these vehicles because of the fast acceleration, quiet ride, and high energy efficiency. The higher pack-to-wheel efficiency and the lower energy cost per mile, as well as the lower expense for maintenance and repair, translate to operating savings over conventional vehicles. Here we compare battery electric vehicles with internal combustion engine vehicles based on the total cost of ownership. It is seen that the higher initial cost of electric vehicles can be recovered in as little as 5 years. This is especially true for electric vehicles with shorter driving ranges. Specifically, a vehicle with an electric driving range under 200 miles may achieve cost parity with an equivalent internal combustion engine vehicle in 8 years or less.

33 ADVANCED PROPULSION SYSTEMS↗

A horizontal powder injector for W7-X

We report that injection of low-Z powders into fusion plasma has been used to improve wall conditions, similar to the standard boronization process using diborane. Powder injection has the advantage of being much simpler, non-toxic, and efficient. The W7-X stellarator is planning on utilizing powder injection in long pulse discharges; a proof-of-principle test for horizontal injection into the plasma was conceived, a Probe Mounted Particle Injector (PMPI). The PMPI concept is developed using a polyetheretherketone (PEEK) paddle wheel hub that is driven by a piezo motor, due to the high magnetic fields, that rotates at 100 deg/s. This small PMPI fits into an envelope of 120 mm diameter × 150 mm long, a standard size for Multi-Purpose Manipulator (MPM). The device is housed in a carbon cup mounted on a retractable probe that can be placed near the plasma edge, enabling powder injection ˜4–8 cm radially into the boundary plasma. The feed for the paddle is via piezo electric actuator that vibrates a funnel filled with powder into a trough for the paddle to push. The 8 paddle arms, 35 mm long and 10 mm wide, are made from 0.38 mm thick PEEK which drag slightly along the powder-filled trough bottom, becoming a spring-loaded paddle which accelerates the powder upon release. Finally, design challenges are the high ambient magnetic field, vacuum compatible materials, high temperature environment, limited rotary-drive options, and compact space. The design and testing of this new device will be presented.

36 MATERIALS SCIENCE↗

Co-optimized trading of hybrid wind power plant with retired EV batteries in energy and reserve markets under uncertainties

To be competitive in the electricity markets, various technologies have been reported to increase profits of wind farm owners. Combining battery storage system, wind farms can be operated as conventional power plants which promotes the integration of wind power into the power grid. However, high expenses on batteries keep investors away. Retired EV batteries, fortunately, still have enough capacity to be reused and could be obtained at a low price. In this work, a two-stage optimization of a wind energy retired EV battery-storage system is proposed. The economic performance of the proposed system is examined concerning its participation in the frequency containment normal operation reserve (FCR-N) market and the spot market simultaneously. To account uncertainties in the wind farm output, various electricity market prices, and up/down regulation status, a scenario-based stochastic programming method is used. The sizing of the equipment is optimized on top of daily operations of the hybrid system which formulates a mixed-integer linear programming (MILP) problem. Scenarios are generated with the Monte Carlo simulation (MCS) and Roulette Wheel Mechanism (RWM), which are further reduced with the simultaneous backward method (SBM) to increase computational efficiency. A 21 MW wind farm is selected as a case study. Here, the optimization results show that by integrating with a retired EV battery-storage system (RESS) and a bi-directional inverter, the wind farm can increase its profits significantly when forwarding bids in both of the aforementioned electricity markets.

17 WIND ENERGY↗

Thermodynamic and kinetic analysis of the melt spinning process of Fe-6.5 wt.% Si alloy

Here, the microstructural evolution of Fe-6.5 wt.% Si alloy during rapid solidification was studied over a quenching rate of 4 × 10 4 K/s to 8 ×10 5 K/s. The solidification and solid-state diffusional transformation processes during rapid cooling were analyzed via thermodynamic and kinetic calculations. The Allen-Cahn theory was adapted to model the experimentally measured bcc_B2 antiphase domain sizes under different cooling rates. The model was calibrated based on the experimentally determined bcc_B2 antiphase domain sizes for different wheel speeds and the resulting cooling rates. Good correspondence of the theoretical and experimental data was obtained over the entire experimental range of cooling rates. Along with the asymptotic domain size value at the infinite cooling rates, the developed model represents a reliable extrapolation for the cooling rate > 10 6 K/s and allows one to optimize the quenching process.

36 MATERIALS SCIENCE↗

Life cycle assessment of fuel ethanol produced from soluble sugar in sweet sorghum stalks in North China

This paper describes the results of a life cycle assessment of sweet sorghum stalk (SSS)-based ethanol in North China. We determined the environmental performance of SSS-based ethanol and examined its advantages and disadvantages, as compared to gasoline, focusing on the life cycle of feedstock production, transportation, ethanol production and distribution, and use. The GREET transportation model and the method developed by the Centre of Environmental Sciences at Leiden University (CML method) were used to compile a life cycle inventory and to assess environmental impacts. Results indicate that SSS-based ethanol has advantages in terms of energy consumption, with a well to wheel decrease of 85% fossil energy and 44% global warming potential, as compared with gasoline. Abiotic depletion potential, acidification potential, and photochemical ozone creation potential were also 50–90% lower than in the case of gasoline, while human health toxic potential was 36% lower. However, SSS-based sorghum did not have advantages over gasoline in terms of life cycle cost, land use, and water consumption. Results indicate that such an evaluation cannot just consider a few types of environmental impacts, researchers should promote systematic and comprehensive life cycle assessment of ethanol to guide the development of an energy strategy for China.

Environment impact↗

An improved stochastic weighted particle method for boundary driven flows

Here, the stochastic weighted particle method (SWPM) is a generalization of the Direct Simulation Monte Carlo (DSMC) method where particle weights are variable and dynamic. SWPM is backed by a strong theoretical foundation but has not been critically evaluated for problems of practical interest. A thorough assessment of SWPM for boundary-driven flows reveals significant numerical artifacts near the boundary, notably a diverging heat flux. To correct the boundary heat flux, two modifications to SWPM are proposed: separated grouping and a spatially-dependent weight transfer function. To gauge the relative efficiency of SWPM in comparison to DSMC, a high-Mach-number wheel flow which forms a strong density gradient is also simulated.

97 MATHEMATICS AND COMPUTING↗

Crystallization behavior in a highly driven marginal glass forming alloy

Al{sub 90}Sm{sub 10}, a marginal glass former, was rapidly solidified using Cu-block single roller melt spinning at wheel speeds of 30 and 40 m/s. The product phases of rapid solidification were identified and analyzed using high energy synchrotron X-ray diffraction (HEXRD), high resolution transmission electron microscopy, and atom probe tomography. The as-quenched structure consists of a saturated amorphous phase and nanocrystalline Al with typical length scale of about 5 nm. The appearance of a pre-peak on HEXRD diffraction patterns and a low activation energy for first crystallization as determined using the Kissinger and Ozawa methods indicate some local ordering in the amorphous phase. The devitrification phase transformation path was determined using in situ high energy synchrotron radiation. Three phases, MS1, H1, and Al{sub 4}Sm, were identified during decomposition of the amorphous phase. MS1, H1 and Al{sub 4}Sm are cubic, hexagonal and orthorhombic metastable phases, respectively.

36 MATERIALS SCIENCE↗

Synthesis, structures, luminescent and magnetic properties of four coordination polymers with the flexible 1,3-phenylenediacetate ligands

Four coordination polymers, [Zn(pda)(bpy)(H{sub 2}O)]{sub n}.nH{sub 2}O (1), [Cd(pda)(prz)(H{sub 2}O)]{sub n} (2), [Co{sub 3}({mu}{sub 3}-OH){sub 2}(pda){sub 2}(pyz)]{sub n}.2nH{sub 2}O (3) and [Pr{sub 2}(pda){sub 3}(H{sub 2}O){sub 2}]{sub n} (4) (H{sub 2}pda=1,3-phenylendiacetic acid, bpy=4,4'-bipyridine, prz=piperazine and pyz=pyrazine) have been hydrothermally synthesized and characterized. Complex 1 is a 1D wheel-like chain structure, which is further extended into a 3D metal-organic supramolecular framework by H-bonds and {pi}-{pi} stacking interactions. Complex 2 is a 1D ladder-like chain structure, which is also further extended into a 3D metal-organic supramolecular framework by H-bonds. Complex 3 possess a 2D sheet structure with infrequent two pairs of double-helix chains. Complex 4 features a 3D structure. Both 1 and 2 display strong blue fluorescent emission at room temperature. Magnetic susceptibility measurements of complexes 3 and 4 exhibit antiferromagnetic interactions between the nearest metal ions, with C=9.99 and 3.43 cm{sup 3} mol{sup -1} K, and {theta}=-23.9 and -46.3 K, respectively. -- Graphical abstract: Four new coordination polymers with 1,3-phenylenediacetate ligands have been hydrothermally synthesized and characterized. Complexes 1 and 2 display strong blue fluorescent emission at room temperature. Magnetic susceptibility measurements of 3 and 4 exhibit antiferromagnetic interactions between the nearest metal centers. Display Omitted Research highlights: > Coordinative property of H{sub 2}pda ligand was shown when bonded by different block metals. > Careful selection of co-ligand and metals resulted in dramatic framework evolution. > (c) The compounds constructed with Zn{sup 2+} and Cd{sup 2+} exhibit strong blue fluorescent emission. > The magneto-structural correlation of the complexes constructed with Co{sup 2+} and Pr{sup 3+} was elucidated.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Three complexes of Cu(I) cluster with flexible and rigid ligands: Synthesis, characterization and photoluminescent properties

Three new Cu(I) cluster complexes, viz. [(Cu{sub 4}I{sub 4})(Cu{sub 2}I{sub 2})(dimb){sub 3}]{sub n} (1; dimb=1,4-diimidazol-1-ylbutane), [(Cu{sub 3}I{sub 2})(dimb)(dmtz)]{sub n} (2; dmtz=3,5-dimethyl-1,2,4-triazole), and [Cu{sub 6}(mbt){sub 6}] (3; mbt=2-mercaptobenzothiazole), have been solvothermally synthesized and structurally characterized. In 1, a Cu{sub 4}I{sub 4} cubane core as a 4-connecting node, connects the neighboring nodes either through single dimb or μ{sub 2}-[(Cu{sub 2}I{sub 2})(dimb){sub 2}] linkers, affording an undulated 2D (4,4) net. Parallel interpenetration occurs between the adjacent nets and thus the overall 2D→3D network is formed. Complex 2 is constructed by 2D (4,4) topological plane grid layers of AB stacking. The core, a distorted triangular bipyramidal Cu{sub 3}I{sub 2} cluster, is acted as a 4-connecting node and connected with dimb and μ{sub 3}-dmtz to form the layer. Complex 3 contains a (Cu{sub 6}S{sub 6}) core in discrete paddle-wheel molecule, which serves as a 4-connecting node to link equivalent ones via π···π interaction, forming 2D (4,4) layers. Solid-state luminescence properties and thermogravimetric analyses of 1, 2 and 3 were investigated. - Graphical abstract: Complexes based on Cu(I) clusters possess two-fold 2D→3D parallel interpenetrating (1), triple emissions (2) and near-infrared emission (3). - Highlights: • Complex 1 represents two-fold 2D→3D parallel interpenetrating framework. • Complex 2 shows triple emissions. • Complex 3 displays a quite intense near-infrared (NIR) emission. • These complexes have good thermal stability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗