Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “VisIt”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Consortium for Verification Technology Fellowship Report.

As one recipient of the Consortium for Verification Technology (CVT) Fellowship, I spent eight days as a visiting scientist at the University of Michigan, Department of Nuclear Engineering and Radiological Sciences (NERS). During this time, I participated in multiple department and research group meetings and presentations, met with individual faculty and students, toured multiple laboratories, and taught one-half of a one-unit class on Risk Analysis in Nuclear Arms control (six 1.5 hour lectures). The following report describes some of the interactions that I had during my time as well as a brief discussion of the impact of this fellowship on members of the consortium and on me/my laboratory’s technical knowledge and network.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

Assessment of the US Department of Energy's Sustainable Energy Resources for Consumers Grant Program

This report presents the results of an assessment of the Sustainable Energy Resources for Consumers (SERC) grant program that was administered by the US Department of Energy Weatherization and Intergovernmental Program Office. Grants totaling $90 million were awarded to 101 local weatherization agencies located in 27 states. More than 15,000 housing units were touched by the SERC program. Close to 29,000 SERC technologies were installed and/or services delivered. The report summarizes the results of site visits to 27 agencies in which the following 14 technologies were observed: solar photovoltaic panels, solar hot water heaters, solar thermal air panels for space heating, tankless water heaters, heat pump water heaters, geothermal heat pumps, super-evaporative cooling systems, combination boilers and indirect water heaters, small-scale residential wind systems, cool roofs, masonry spray foam insulation, attic radiant barriers, mini-split heat pumps, and in-home energy monitors. The evaluation found that the national weatherization network is capable of installing and delivering a wide range of new and innovative technologies, but the usability and adoptability of some technologies may prove impractical for the weatherization network and the demographic for which it serves.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Final Report - Subcontract B623760

During my visit to LLNL during July 17{27, 2017, I worked on linear system solvers. The two level hierarchical solver that initiated our study was developed to solve linear systems arising from hp adaptive finite element calculations, and is implemented in the PLTMG software package, version 12. This preconditioner typically requires 3-20% of the space used by the stiffness matrix for higher order elements. It has multigrid like convergence rates for a wide variety of PDEs (self-adjoint positive de nite elliptic equations, convection dominated convection-diffusion equations, and highly indefinite Helmholtz equations, among others). The convergence rate is not independent of the polynomial degree p as p ! 1, but but remains strong for p 9, which is the highest polynomial degree allowed in PLTMG, due to limitations of the numerical quadrature rules implemented in the software package. A more complete description of the method and some numerical experiments illustrating its effectiveness appear in. Like traditional geometric multilevel methods, this scheme relies on knowledge of the underlying finite element space in order to construct the smoother and the coarse grid correction.

97 MATHEMATICS AND COMPUTING↗

High-Efficiency Housing at the Fort Peck Indian Reservation: Opportunities and Lessons Learned

This project was initiated to provide design assistance in an effort to maximize energy performance for affordable housing at the Fort Peck Indian Reservation near Poplar, Montana. The Make It Right Foundation (MIRF) built 20 high performing homes (LEED Platinum) in 2015 and 2016 with three (3) different design options. NREL and EPA set out to provide energy analysis along with measurement and verification (M and V) of the homes to characterize energy use and provide clarity for future decision making with regard to tribal housing options. The results included herein summarize the energy end uses and documents projected energy impacts from various aspects of the MIRF home designs and construction. This report includes an analysis of energy use in 5 MIRF homes, comparing energy use across the different styles and configurations. Energy models were created for the 2 styles of MIRF homes, including renewable energy assessment for photovoltaic (PV) systems. Existing tribal housing has also been analyzed, with 5 housing units being analyzed for energy use and an energy model being created for 1 housing unit. The findings of this study highlight many of the challenges that arise when attempting to construct high performance housing in a region where such construction practices are still relatively rare. Homes in Poplar are well designed and, for the most part, and include climate specific design considerations appropriate for northeastern Montana. The most significant issues identified in MIRF homes were related to the work done to put the homes on the foundation, insulate the crawlspaces, and do final connection with the utilities. The Taxed II Credit homes are well designed and well suited to northeastern Montana, and with slight modifications to the design and construction could be very efficient. All occupant comfort and energy usage issues that were identified during the site visits can be remedied through retrofit measures that are relatively inexpensive. Energy efficiency opportunities were found that can be implemented in each of the homes. These retrofits are generally inexpensive and have a quick return on investment. While the MIRF houses as well as the Taxed II Credit homes can achieve high levels of energy performance with modest retrofits. Similar houses built in the future could achieve even better performance with minor design changes, and generally low incremental cost. Renewable energy systems are economically feasible in this area, but the payback is on the high side of what would likely be acceptable to homeowners. If the price of solar comes down to $2/watt installed, the systems will achieve a simple payback of 13 years, which is likely a return on investment that is attractive to homeowners. If the homes are made sufficiently tight to be high performance, energy recovery ventilators will be necessary to maintain acceptable indoor air quality. The Taxed II Credit homes are already equipped with heat recovery ventilators (HRVs), and they seem to function well. As PV prices continue to decline, start implementing projects as they become cost effective.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

MST e-News March 2018

Growing up, Matthew Herman explored new worlds through books. He had enrolled at Western Washington University, intent on studying literature and becoming a writer, when a professor suggested he visit the school’s engineering department. Herman soon determined that science has, at its core, the same purpose that motivated him to write– problem-solving. He now makes discoveries as an R&D technologist in Engineered Materials (MST-7), applying his affinity for creating and problem-solving to materials with clear, concrete applications, such as additively manufactured microlattice structures and a particle accelerator the size of a shoebox.

36 MATERIALS SCIENCE↗

Marine Hydrokinetic Resource Assessment for Domestic Army, Air Force, and Coast Guard Facilities

NREL/DOE undertook a study for the US Army, Coast Guard and Air Force to investigate the potential for marine hydrokinetic (MHK) devices to meet the energy load at coastal bases in the future as MHK technology evolves. A wide range of data from tidal and wave, environmental, shipping, etc. databases were used to screen the DOD bases. A series of scoring algorithms were developed to facilitate site review to lead to eventual down select for more detailed, site specific bathymetric tidal resource evaluation. The Army's Camp Edwards, MA and the Coast Guard's Training Center Cape May, NJ (TRACEN Cape May) were selected and the Georgia Institute of Technology performed the analyses. An NREL/DOE MHK team visited the bases to further discuss with the base personnel MHK technology's potential for providing power to the bases in the future and frame the potential impact to existing power systems.

13 HYDRO ENERGY↗

Lab touts plutonium storage best practices for Japanese visitors

Engineers from Japan's Oarai Research and Development Center's Plutonium Fuel Research Facility visited TA-55's Plutonium Facility 4 (PF-4) recently to learn best practices from the Laboratory for safely packaging and storing plutonium and other radioactive materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE Residential Energy Code Field Study - Pennsylvania

This project consisted of three distinct phases – all focused on residential one- and two-family dwellings and townhouses. Phase 1 included a baseline field study with inspections and performance testing to assess construction practices with respect to the energy code. PNNL used the data to perform EUI and savings potential analyses. Phase 2 consisted of training, education, and outreach to building industry professionals with content based on the findings from Phase 1. Phase 3 was a post-program field study using the same methodology as Phase 1 and was intended to measure the impact of Phase 2. During Phase 1 of the project, PSD collected data from 171 job sites across eastern Pennsylvania, a territory bounded by PECO, PPL, and Met-Ed electric distribution territories, to reach the required 63 “home equivalents” deemed necessary by PNNL for a representative sample. Based on subsequent analysis, four key items were identified as having significant savings potential from improvement in compliance, including duct leakage, above-grade wall insulation (specifically insulation installation quality), foundation insulation, and high-efficacy lighting. About half the total savings potential is from duct leakage, so that was the primary focus. The goal of Phase 2 was to improve upon these key compliance weaknesses through an intensive training, education, and outreach program. PSD dubbed this effort the Penn Energy Codes Program. For Phase 3, PSD obtained a new sample plan from PNNL, obtained permit data from sample municipalities, and made substitutions where necessary. PSD field staff visited 165 job sites to collect the required 504 key observations. PSD submitted all data collection sheets to PNNL for their analysis to determine if there was a measurable change due to Phase 2 activities.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Waste to Wisdom: Utilizing Forest Residues for the Production of Bioenergy and Biobased Products

The Waste to Wisdom project was part of the Biomass Research and Development Initiative (BRDI) and funded by the Department of Energy (DE-EE0006297) at an amount of $5.8 million. Our interdisciplinary research team, consisting of academics, business professionals, and land managers, worked together for about four years (September 2013 to December 2017) to: 1) conduct field-based experiments to develop innovative tools and systems that improve the economics, accessibility, and production of quality feedstocks from forest residues, 2) develop and test stand-alone in-woods or near-the forest biomass conversion technologies (BCTs) for the production of biochar, torrefied wood, and briquettes, and 3) perform analyses to evaluate the economic feasibility of commercial deployment of BCTs and to quantify the life cycle economic and environmental benefits of utilizing forest residues with BCTs for the production of bioenergy and bioproducts. The research papers presented in this Special Issue cover key aspects of the research efforts and findings made by the project team. We encourage the audience to visit the project web site (http://wastetowisdom.com/) to learn more about the team’s research on feedstock development, biomass conversion technologies, and the financial and environmental benefits of utilizing forest residues for production of bioenergy and biobased products.

09 BIOMASS FUELS↗

University Research in Support of TREAT Modeling and Simulation, FY 2017

INL is currently evolving a modeling and simulation (M&S) capability that will enable im- proved core operation as well as design and analysis of TREAT experiments. This M&S capability primarily uses MAMMOTH, a reactor physics application being developed under the Multi-physics Object Oriented Simulation Environment (MOOSE) framework. MAMMOTH allows the coupling of a number of other MOOSE-based applications. This work is being supplemented by related research projects at a number of universities. INL is funding TREAT-related research at North Carolina State University, University of New Mexico, Oregon State University, and MIT under internally funded projects within the INL/Battelle National University Consortium Program. Under the DOE Nuclear Energy Advanced Modeling and Simulation program (NEAMS), other research is being performed at MIT, University of Florida, and Texas A&M University. In addition, Dr. Barry Ganapol of University of Arizona was funded for summer work at the INL. This report is a compilation of conference papers that were submitted as part of this research by the NEAMS University partners and from the visiting professor.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Integrated Component-Specific Measurements to Develop Emission Factors for Compressors and Gas Gathering Lines

The Department of Energy (DOE) National Energy Technology Laboratory (NETL) and other critical stakeholders (e.g., U.S. Environmental Protection Agency (USEPA), state regulators, and industry) seek to more accurately characterize and quantify methane emissions from compressors and gathering lines within the Gathering and Boosting (G&B) segment of the natural gas system network. These efforts will reduce uncertainties in emissions estimates in USEPA’s current Green House Gas Inventory (GHGI) under their Greenhouse Gas Reporting Program (GHGRP). For this study, four G&B stations in the Gulf Coast Area were visited four times over the course of one year. Components were classified according to equipment and component type and emissions from select components were measured using multiple measurement technologies. The following major equipment types were considered: i) compressors, ii) separators, iii) dehydrators, iv) coalescers, v) slug catchers, vi) yard piping, vii) tanks, and viii) gathering lines. Individual components on each equipment type were further divided into the following main categories: i) connectors, ii) valves, iii) pressure relief valves (PRV), iv) meters, v) gauges, vi) regulators, vii) pneumatic device vents, and viii) compressor vents (e.g., distance piece vents [DPVs] and rod packing vents [RPVs]). Components were screened for the presence of leaks and venting emissions with an optical gas imaging (OGI) camera, and methane emission rates were measured using a microdilution high volume sampler. Downwind emissions were measured using an Open Path Fourier Transform Infrared (OP-FTIR) Spectrometer. Data were evaluated to assess correlation with site, equipment, time, and operational variables. Key findings and recommendations from the study include: A) Different counting methodologies can result in vastly different component counts, thus influencing total emissions calculations using Subpart W population EFs. A standard methodology should be adopted for classifying and counting components in order to minimize inconsistencies across studies and instruct stakeholders responsible for GHGI reporting. B) Results support current component subcategories listed in USEPA Subpart W, including the subdivision of connectors (flanged and “other”) and pneumatic device vents (intermittent, continuous low bleed, and continuous high bleed). C) Emission rates vary across sites and a relationship between higher emissions and compressor age was observed for some components. D) Component emission rates varied between field campaigns. The type of components contributing to overall measured emissions also varied among field campaigns. However, the emission rate variability was larger between different components (of the same category) than the variability in one component over the four field campaigns. Therefore, when calculating emission factors, it is not necessary to take repeat measurements to capture component variability. E) Measuring the emission rate of a sample for an extended period of time is not necessary to capture the average component emission rate. F) For reporting purposes, excluding liquid lines from site-wide screening may have a negligible effect on component-related emissions. However, from a site management perspective, malfunctioning components were not uncommon on liquid lines and contributed substantially to fugitive emissions at some sites. G) Population EFs, whether including or excluding liquid lines, were a conservative estimate of fugitive emissions. Leaker EFs consistently underestimated emissions at the field sites. Measurements at more sites, particularity sites in other areas of the country, need to be completed before determining the accuracy of EFs.

03 NATURAL GAS↗

PROTEUS-MOC User Manual

The PROTEUS-MOC code is a three-dimensional (3D) neutron transport code based on the finite element mesh and the method of characteristics (MOC) which combines a 2D MOC with the discontinuous Galerkin finite element method for the axial direction. Thus, for PROTEUS-MOC, a 3D geometry is represented with by the implicit extrusion of a single 2D planar geometry with different material assignments allowable on each plane. The code requires four input files for a steady-state calculation without the thermal feedback: a driver input, a mesh input, a cross section input, and a material assignment input. With thermal feedback, a T/H input file is needed. For kinetics, a kinetics driver input file is required. The PROTEUS-MOC software produces a text output file as well as a data file which includes integral and average quantities such on fluxes, powers, temperatures, densities, etc. The detailed output file can be converted to the VTK format using the post processing code so that the outputs can be visualized using a visualization software such as VisIt.

97 MATHEMATICS AND COMPUTING↗

ECP Milestone Memo WBS 2.3.4.13 ECP/VTK-m FY19Q1 [MS-19/01-03] ZFP / Release / Clip STDA05-17

The STDA05-17 milestone comprises the following 3 deliverables. VTK-m Release 2 We will provide a release of VTK-m software and associated documentation. The source code repository will be tagged at a stable state, and, at a minimum, tarball captures of the source code will be made available from the web site. A version of the VTK-m User's Guide documenting this release will also be made available. Productionize zfp compression The "ZFP: Compressed Floating-Point Arrays" project (WBS 1.3.4.13) is creating an implementation of ZFP compression in VTK-m. Their implementation will be focused on operating in CUDA. The VTK-m project will assist by generalizing the implementation to other devices (such as multi-core CPUs). We will also assist in productionizing the code such that it can be used by external projects and products. Clip Clip operations intersect meshes with implicit functions. It is the foundation of spatial subsetting algorithms, such as "box," and the foundation of data-based subsetting, such as "isovolume." The algorithm requires considering thousands of possible cases, and is thus quite difficult to implement. This milestone will implement clipping to be sufficient for Visit's and ParaView's needs.

97 MATHEMATICS AND COMPUTING↗

ECP Milestone Memo WBS 2.3.4.13 ECP/VTK-m FY18Q4 [MS-18/09-10] Dynamic Types / Rendering Topologies STDA05-16

The STDA05-16 milestone comprises the following 3 distinct deliverables. OpenMP VTK-m currently supports three types of devices: serial CPU, TBB, and CUDA. To run algorithms on multicore CPU-type devices (such as Xeon and Xeon Phi), TBB is required. However, there are known issues with integrating a software product using TBB with another one using OpenMP. Therefore, we will add an OpenMP device to the VTK-m software. When engaged, this device will run parallel algorithms using OpenMP directives. This will mesh more nicely with other code also using OpenMP. Rendering Topological Entities VTK-m currently supports surface rendering by tessellation of data structures,and rendering the resulting triangles. We will extend current functionality to include face, edge, and point rendering. Better Dynamic Types Impl For the best efficiency across all platforms, VTK-m algorithms use static typing with C++ templates. However, many libraries like VTK, ParaView, and Visit use dynamic types with virtual functions because data types often cannot be determined at compile time. We have an interface in VTK-m to merge these two typing mechanisms by generating all possible combinations of static types when faced with a dynamic type. Although this mechanism works, it generates very large executables and takes a very long time to compile. As we move forward, it is clear that these problems will get worse and become infeasible at exascale. We will rectify the problem by introducing some level of virtual methods, which require only a single code path, within VTK-m algorithms. This first milestone produces a design document to propose an approach to the new system.

97 MATHEMATICS AND COMPUTING↗

An Overview of Technologies for Individual Trip History Collection: Mobility Decision Science Pillar SMART Mobility Consortium

WholeTraveler is a project of the Department of Energy's Smart Mobility consortium that explores how an individual's attitudes and lifestyle characteristics are embodied in transportation behaviors throughout one's life trajectory. As a study at the nexus of decision science and urban systems analysis, fine-grained location data (FGLD), or records of an individual's location collected at a resolution sufficient to determine both the unique destinations a traveler visits each day and the modes used to travel between them, underlie high quality results. Moreover, the methods for collecting FGLD and the means through which they are associated with a traveler's personal attributes have significant implications for the burden on research participants, the cost and complexity of the study, as well as the confidence with which hypotheses can be validated. This paper provides a broad overview of existing technologies for FGLD collection and is intended to provide a literature review for researcher exploring similar domain areas. Technologies are categorized as either network or onboard approaches. An onboard system, such as smartphone or GPS device, sends signals to external networks to capture its own location. Conversely, network systems, such as cell towers, are comprised of sensing nodes with known locations that record when individually identifiable assets come within their range of detection. Our analysis indicates that the most sensible approach to FGLD collection, for the purposes of WholeTraveler, is to leverage onboard devices, and in particular the existing Moves or Google Maps applications for Android and iOS smartphones. Dedicated GPS devices have been widely implemented by the transportation research community and pose an alternatively acceptable form of FGLD collection. Independently developing a custom smartphone application is not recommended because of the notable challenges in establishing minimal viable functionality, as well as in ensuring compatibility across an ever-growing combination of hardware devices and software versions. No matter the technical means of data collection, the secure handling of FGLD is of critical importance.

33 ADVANCED PROPULSION SYSTEMS↗

United States Nuclear Manufacturing Infrastructure Assessment

This report provides a review and assessment of the existing U.S. infrastructure capabilities to manufacture on a commercial scale, the major components and unique materials required by the various U.S. designs for advanced nuclear reactors and small modular reactors (SMRs). The approach was to compare the needs of SMRs and advanced reactors against the capability of U.S. manufacturers to ascertain gaps that could inhibit U.S. industrial support for deployment of SMRs or advanced reactors. This report focused on the reactor plant designs being developed by NuScale Power (the NuScale Power Module), TerraPower (both the Traveling Wave Reactor and the Molten Chloride Fast Reactor to a limited extent), and X-energy (the Xe-100). To gather the information, MPR visited each of these companies and selected candidate suppliers to tour their facilities and conduct in-person interviews. Information was also obtained by telephone interviews, internet research, and literature review of technical reports. The overarching conclusion from this study is that the U.S. has existing capability or can readily develop capability to support and sustain most, but not all, aspects of commercial deployment of advanced reactors and SMRs. The greatest concerns for capability gaps in the U.S. infrastructure for supply of components for SMRs and advanced reactors are associated with reactor pressure vessels, steam generators, and fuel fabrication. Foreign vendors can supply reactor pressure vessels and steam generators. Issues with fuel fabrication are associated with uranium enrichment and development of fabrication methods for the innovative fuel concepts planned for advanced reactors. The technical capabilities of U.S. manufacturers appear satisfactory with the possible exceptions noted above. However, the capacity of the existing U.S. manufacturing infrastructure may be insufficient for a high rate of construction. Manufacturers contacted as part of this study indicated a willingness to expand capacity if sufficient orders are in place. The review of U.S. infrastructure included a detailed review of capabilities in many different processes including forging, tube drawing, machining, fabrication, and testing. In addition, MPR researched the advanced manufacturing processes for additive manufacturing (i.e., 3D printing) and powder metallurgy - hot isostatic pressing. Reactor plant designers and candidate suppliers are planning to rely on traditional processes for the initial plants. If advanced manufacturing processes are developed and accepted by the nuclear industry, these processes may be used in the future. In the immediate term, ongoing research (much of which is funded by DOE) is necessary to develop and refine advanced manufacturing methods. This report includes several recommendations for DOE that will advance deployment of SMRs and advanced reactors from a manufacturing perspective and other areas identified during the course of this project.

36 MATERIALS SCIENCE↗

Final Technical Report - Renewable Energy Clean Air Project (RECAP)

The Renewable Clean Air Project (RECAP) is the culmination of a design of a 21 st century integrated waste-to-energy facility that encapsulates the best practices of the existing waste-to energy industry and new knowledge worldwide for bettering the industry. After visiting and reviewing several waste-to-energy facilities first hand on different continents and examining different new technologies, Koochiching Development Authority(KDA) and Coronal obtained an unique understanding of the waste-to-energy industry and how different technologies can better the industry.

09 BIOMASS FUELS↗

Study of Regional Climate Change Final Technical Report

Anthropogenic activity of fossil fuel and biomass burning emissions increase tropospheric aerosol concentrations causing a direct cooling effect by scattering solar radiation and thus increasing the Earth’s albedo. In addition, the aerosols can act as cloud condensation nuclei to regulate cloud droplet number and size, thereby changing both the cloud albedo, and the cloud lifetime and precipitation. Thus, the aerosol climate effect concerns intricate aerosol-cloud-radiation-precipitation interactions which are recognized to introduce the largest uncertainties in using GCMs to project future regional climate changes. The climate effects of aerosols are significant in the land regions of the Northern Hemisphere, in particular the sulfate aerosols over East Asia where significant anthropogenic SO 2 emissions have been observed and concentrations of other aerosol species are also high. The objective of the present project is to advance “modeling aerosol-cloud-climate interactions” in two areas: the aerosol-cloud microphysics interactions and model simulations of aerosol effects on regional climate with focus on East Asia. To achieve the objective, in addition to analyzing relevant observations, the project conducts and diagnoses regional and global climate model simulations. Specifically, two collaborative tasks were carried out: Task-1: Incorporating a physics-based, two-moments cloud scheme developed by J. P. Chen/National Taiwan University (NTU) into regional models (WRF and WRF-Chem) to study “aerosol-cloud microphysics interactions over eastern China and the southeast Pacific” ; for latter region, CMIP5 models exhibit distinct biases in (weaker) cloud radiative effects and (warmer) sea surface temperature. The task is conducted in collaboration with J.-P. Chen, H.-W. Xue/Peking University, and H. Liao/Institute of Atmospheric Physics; and Task-2: Diagnosis of NCAR-CESM and WRF model simulations of “aerosol climate effects” focusing on changes of circulation, precipitation and clouds over East Asia. The task is conducted in collaboration with J.-P. Chen, and I-Chun Tsai & H.-H. Hsu/Academia Sinica. For each task, several topical studies were carried out and documented in eleven (11) articles (five for Task-1 and six for Task-2), published in: J. Atmospheric Sciences (2); J. Climate (1); Climate Dynamics (3); J. Geophysical Research (2); Geophysical Research Letter (1); Int. J. Climatology (1); and Advances in Atmospheric Sciences (1). In addition, Wei-Chyung Wang (the PI) continues serving as the U. S. Chief Scientist for the joint agreement, “Climate Sciences”, between the U. S. DOE and China Ministry of Sciences and Technology (Riches et al., 2010). In this capacity, he works closely with Michael Riches/DOE (the U. S. Manager) to coordinate the scientific exchanges (visiting scientists) between the two countries. Educations (graduate students) and trainings (postdoctoral research associates) are key elements of the research project.

54 ENVIRONMENTAL SCIENCES↗