Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solar Radiation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Methodology for Estimating Solar Potential on Multiple Building Rooftops for Photovoltaic Systems

In this paper, a methodology for estimating solar potential on multiple building rooftops is presented. The objective of this methodology is to estimate the daily or monthly solar radiation potential on individual buildings in a city/region using Light Detection and Ranging (LiDAR) data and a geographic information system (GIS) approach. Conceptually, the methodology is based on the upward-looking hemispherical viewshed algorithm, but applied using an area-based modeling approach. The methodology considers input parameters, such as surface orientation, shadowing effect, elevation, and atmospheric conditions, that influence solar intensity on the earth s surface. The methodology has been implemented for some 212,000 buildings in Knox County, Tennessee, USA. Based on the results obtained, the methodology seems to be adequate for estimating solar radiation on multiple building rooftops. The use of LiDAR data improves the radiation potential estimates in terms of the model predictive error and the spatial pattern of the model outputs. This methodology could help cities/regions interested in sustainable projects to quickly identify buildings with higher potentials for roof-mounted photovoltaic systems.

14 SOLAR ENERGY↗

A canopy reflectance model based on an analytical solution to the multiple scattering equation

An approximation to the radiative transfer equation for solar radiation in relatively full, homogeneous plant canopies is presented and solved analytically for solar zenith angles less than 60 deg. The model predicts reflectance at any depth in the canopy and in any direction and may be inverted with bidirectional reflectance measurements. The model was fit to data at two sun angles and two wavebands (visible and NIR) to within the assumed errors on the reflectance data. The calculated albedos are insensitive to achievable measurement errors. Some of the parameter values themselves found by the inversion agree reasonably well with independent measurements, but the uncertainties introduced by the data noise are rather large. However, the agreement is good enough to demonstrate that the model is physically realistic.

Camillo, Peter↗

Orbit Determination for the Lunar Reconnaissance Orbiter Using an Extended Kalman Filter

Orbit determination (OD) analysis results are presented for the Lunar Reconnaissance Orbiter (LRO) using a commercially available Extended Kalman Filter, Analytical Graphics' Orbit Determination Tool Kit (ODTK). Process noise models for lunar gravity and solar radiation pressure (SRP) are described and OD results employing the models are presented. Definitive accuracy using ODTK meets mission requirements and is better than that achieved using the operational LRO OD tool, the Goddard Trajectory Determination System (GTDS). Results demonstrate that a Vasicek stochastic model produces better estimates of the coefficient of solar radiation pressure than a Gauss-Markov model, and prediction accuracy using a Vasicek model meets mission requirements over the analysis span. Modeling the effect of antenna motion on range-rate tracking considerably improves residuals and filter-smoother consistency. Inclusion of off-axis SRP process noise and generalized process noise improves filter performance for both definitive and predicted accuracy. Definitive accuracy from the smoother is better than achieved using GTDS and is close to that achieved by precision OD methods used to generate definitive science orbits. Use of a multi-plate dynamic spacecraft area model with ODTK's force model plugin capability provides additional improvements in predicted accuracy.

Orbit Determination↗

Laboratory simulation of interstellar grain chemistry and the production of complex organic molecules

During the past 15 years considerable progress in observational techniques has been achieved in the middle infrared (5000 to 500 cm(-1), 2 to 20 microns m), the spectral region most diagnostic of molecular vibrations. Spectra of many different astronomical infrared sources, some deeply embedded in dark molecular clouds, are now available. These spectra provide a powerful probe, not only for the identification of interstellar molecules in both the gas solid phases, but also of the physical and chemical conditions which prevail in these two very different domains. By comparing these astronomical spectra with the spectra of laboratory ices one can determine the composition and abundance of the icy materials frozen on the cold (10K) dust grains present in the interior of molecular clouds. These grains and their ice mantles may well be the building blocks from which comets are made. As an illustration of the processes which can take place as an ice is irradiated and subsequently warmed, researchers present the infrared spectra of the mixture H2O:CH3OH:CO:NH3:C6H14 (100:50:10:10:10). Apart from the last species, the ratio of these compounds is representative of the simplest ices found in interstellar clouds. The last component was incorporated into this particular experiment as a tracer of the behavior of a non-aromatic hydrocarbon. The change in the composition that results from ultraviolet photolysis of this ice mixture using a UV lamp to simulate the interstellar radiation field is shown. Photolysis produces CO, CO2, CH4, HCO, H2CO, as well as a family of moderately volatile hydrocarbons. Less volatile carbonaceous materials are also produced. The evolution of the infrared spectrum of the ice as the sample is warmed up to room temperature is illustrated. Researchers believe that the changes are similar to those which occur as ice is ejected from a comet and warmed up by solar radiation. The warm-up sequence shows that the nitrile or iso-nitrile bearing compound produced during photolysis evaporates between 200 and 250K, suggesting that it is carried by a small molecular species. These molecules could be similar to the source material in Comet Halley that is ejected in grains into the coma, freed by sublimation, and photolyzed by solar radiation to produce the observed jets.

Allamandola, L. J.↗

Orbit determination requirements for TOPEX

The error sensitivity of orbit calculations in support of the NASA Ocean Surface Topography Mapping Experiment (TOPEX), which require an accuracy on the order of 5 cm, is investigated. The contributions of errors in the gravitational, atmospheric drag and solar radiation pressure models to the computed orbit are analyzed for the cases of an ideal data distribution and realistic laser ranging data coverage. It is found that the major contributor to radial orbital error is the error in the geopotential model, accounting for orbital errors of 30 to 70 cm, with the effects of solar radiation pressure, drag modeling, tracking station coordinate errors making lesser contributions. It is concluded that TOPEX accuracy goals cannot be met using ground-based laser ranging data without improving the geopotential model.

Tapley, B. D.↗

Airborne Remote Sensing Measurements of Particles in Different Parts of the World

Around the globe, atmospheric aerosols pose a significant yet uncertain impact on the Earth's climate, environmental air quality and human health. Suborbital sunphotometer measurements of Aerosol Optical Depth (AOD) (i.e., the amount of direct-beam solar light attenuated by aerosols within the atmospheric column) are used to validate satellite aerosol retrievals and are valuable when studying aerosol-solar radiation and/ or aerosol-cloud interactions. Since 1985, NASA Ames Research Center (ARC) has been using airborne sun-tracking sunphotometers to measure atmospheric constituents such as aerosols, clouds, and gases. The NASA Ames Airborne Tracking Sunphotometer (AATS-6) and then (AATS-14) operate by tracking the sun and measuring the transmission of solar radiation in 6 to 14 discrete spectral channels (Russell et al., 1986). The AATS systems were followed by the more advanced hyperspectral 4STAR instrument (Spectrometer for Sky-Scanning, Sun-Tracking Atmospheric Research; Dunagan et al., 2013), which combines the airborne sun-tracking capability of the AATS-14 with a sky scanning feature similar to the ground-based Aerosol Robotic Network Sun/sky photometers (AERONET). We present a comprehensive analysis of ~30 airborne campaigns undertaken by NASA and DoE based on a new database of airborne sunphotometer measurements. Using this database, we present a clear picture of airborne AODs over the range of historical campaigns and the aerosol sizes per region, especially over the ocean where AERONET data is limited. With this database, we can investigate systematic differences in AOD such as those observed over different land and ocean surfaces in specific geographical regions. Finally, we will briefly show comparisons with satellite aerosol retrievals from MODIS and/or VIIRS. Russell, P. B., T. Matsumoto, V. J. Banta, J. M. Livingston, C. Mina, D. S. Colburn, and R. F. Pueschel (1986), Measurements with an airborne, autotracking, external-head sunphotometer, Preprint Volume, Sixth Conference on Atmospheric Radiation, May 13–16, 1986, Amer. Meteor.Soc., Boston, MA, 55–58. Dunagan, Stephen E., et al. "Spectrometer for sky-scanning sun-tracking atmospheric research (4STAR): Instrument technology." Remote Sensing 5.8 (2013): 3872-3895

Brendan Stover Cornelison↗

Global ocean dimethyl sulfide climatology estimated from observations and an artificial neural network

Marine dimethyl sulfide (DMS) is important to climate due to the ability of DMS to alter Earth's radiation budget. Knowledge of the global-scale distribution, seasonal variability, and sea-to-air flux of DMS is needed in order to improve understanding of atmospheric sulfur, aerosol/cloud dynamics, and albedo. Here we examine the use of an artificial neural network (ANN) to extrapolate available DMS measurements to the global ocean and produce a global climatology with monthly temporal resolution. A global database of 82 996 ship-based DMS measurements in surface waters was used along with a suite of environmental parameters consisting of latitude–longitude coordinates, time of day, time of year, solar radiation, mixed layer depth, sea surface temperature, salinity, nitrate, phosphate, and silicate. Linear regressions of DMS against the environmental parameters show that on a global-scale mixed layer depth and solar radiation are the strongest predictors of DMS. These parameters capture ~9 % and ~7 % of the raw DMS data variance, respectively. Multilinear regression can capture more of the raw data variance (~39 %) but strongly underestimates DMS in high-concentration regions. In contrast, the artificial neural network captures ~66 % of the raw data variance in our database. Like prior climatologies our results show a strong seasonal cycle in surface ocean DMS with the highest concentrations and sea-to-air fluxes in the high-latitude summertime oceans. We estimate a lower global sea-to-air DMS flux (20.12±0.43 Tg S yr –1 ) than the prior estimate based on a map interpolation method when the same gas transfer velocity parameterization is used. Our sensitivity test results show that DMS concentration does not change unidirectionally with each of the environmental parameters, which emphasizes the interactions among these parameters. The ANN model suggests that the flux of DMS from the ocean to the atmosphere will increase with global warming. Given that larger DMS fluxes induce greater cloud albedo, this corresponds to a negative climate feedback.

54 ENVIRONMENTAL SCIENCES↗

NISAR Spacecraft Environmental Torque Modeling During Operations

Environmental torques imparted on the NISAR (NASA-ISRO (NASA Jet PropulsionLaboratory (JPL)-Indian Space Research Organization (ISRO) Synthetic Aperture Radar) spacecraft are modeled. The environmental torques comprise of the gravity gradient, atmospheric drag, and solar radiation pressure. These torques act as external disturbances on the spacecraft and cause momentum to accumulate. This momentum needs to be unloaded via attitude control hardware. In order to size the hardware, it is important to determine the environmental torques imparted on the spacecraft. The results indicate that the worst case gravity gradient, drag, and solar radiation pressure torques are 7.4 by 10 (sup -3) Nm (Newton meters), 6.01 by 10 (sup -3) Nm, and 14.03 by 10(sup -3) Nm, respectively.

Rizvi, Farheen↗

Energy and cost analysis of a solar-hydrogen combined heat and power system for remote power supply using a computer simulation

A simulation program, based on Visual Pascal, for sizing and techno-economic analysis of the performance of solar-hydrogen combined heat and power systems for remote applications is described. The accuracy of the submodels is checked by comparing the real performances of the system's components obtained from experimental measurements with model outputs. The use of the heat generated by the PEM fuel cell, and any unused excess hydrogen, is investigated for hot water production or space heating while the solar-hydrogen system is supplying electricity. A 5 kWh daily demand profile and the solar radiation profile of Melbourne have been used in a case study to investigate the typical techno-economic characteristics of the system to supply a remote household. The simulation shows that by harnessing both thermal load and excess hydrogen it is possible to increase the average yearly energy efficiency of the fuel cell in the solar-hydrogen system from just below 40% up to about 80% in both heat and power generation (based on the high heating value of hydrogen). The fuel cell in the system is conventionally sized to meet the peak of the demand profile. However, an economic optimisation analysis illustrates that installing a larger fuel cell could lead to up to a 15% reduction in the unit cost of the electricity to an average of just below 90 c/kWh over the assessment period of 30 years. Further, for an economically optimal size of the fuel cell, nearly a half the yearly energy demand for hot water of the remote household could be supplied by heat recovery from the fuel cell and utilising unused hydrogen in the exit stream. Such a system could then complement a conventional solar water heating system by providing the boosting energy (usually in the order of 40% of the total) normally obtained from gas or electricity. (author)

14 SOLAR ENERGY↗

Interpretation of solar irradiance monitor measurements through analysis of 3D MHD simulations

Measurements from the Spectral Irradiance Monitor (SIM) on board the Solar Radiation and Climate Experiment mission indicate that solar spectral irradiance at visible and IR wavelengths varies in counter phase with the solar activity cycle. The sign of these variations is not reproduced by most of the irradiance reconstruction techniques based on variations of surface magnetism employed so far, and it is not yet clear whether SIM calibration procedures need to be improved or if instead new physical mechanisms must be invoked to explain such variations. We employ three-dimensional magnetohydrodynamic simulations of the solar photosphere to investigate the dependence of solar radiance in SIM visible and IR spectral ranges on variations of the filling factor of surface magnetic fields. We find that the contribution of magnetic features to solar radiance is strongly dependent on the location on the disk of the features, which are negative close to disk center and positive toward the limb. If features are homogeneously distributed over a region around the equator (activity belt), then their contribution to irradiance is positive with respect to the contribution of HD snapshots, but decreases with the increase of their magnetic flux for average magnetic flux larger than 50 G in at least two of the visible and IR spectral bands monitored by SIM. Under the assumption that the 50 G snapshots are representative of quiet-Sun regions, we thus find that the Spectral Irradiance can be in counter-phase with the solar magnetic activity cycle.

79 ASTRONOMY AND ASTROPHYSICS↗

Solar cells based on gallium antimonide

Liquid-phase epitaxy and diffusion from the gas phase have been used to create various kinds of GaSb-based solar cell structures intended for use in cascaded solar-radiation converters. A narrow-gap (GaSb) solar cell was studied in tandem based on a combination of semiconductors GaAs-GaSb (two p-n junctions) and GaInP/GaAs-GaSb (three p-n junctions). The maximum efficiency of photovoltaic conversion in GaSb behind the wide-gap cells is {eta} = 6.5% (at sunlight concentration ratio of 275X, AM1.5D Low AOD spectrum)

36 MATERIALS SCIENCE↗

Possibility of using sources of vacuum ultraviolet irradiation to solve problems of space material science

An urgent problem in space materials science is simulating the interaction of vacuum ultraviolet (VUV) of solar emission with solids in space conditions, that is, producing a light source with a distribution that approximates the distribution of solar energy. Information is presented on the distribution of the energy flux of VUV of solar radiation. Requirements that must be satisfied by the VUV source used for space materials science are formulated, and a critical evaluation is given of the possibilities of using existing sources for space materials science. From this evaluation it was established that none of the sources of VUV satisfies the specific requirements imposed on the simulator of solar radiation. A solution to the problem was found to be in the development of a new type of source based on exciting a supersonic gas jet flowing into vacuum with a sense electron beam. A description of this gas-jet source, along with its spectral and operation characteristics, is presented.

Verkhoutseva, E. T.↗

Satellite-Based Surface Heat Budgets and Sea Surface Temperature Tendency in the Tropical Eastern Indian and Western Pacific Oceans for the 1997/98 El Nino and 1998/99 La Nina

The 1997/98 is a strong El Nino warm event, while the 1998/99 is a moderate La Nina cold event. We have investigated surface heat budgets and sea surface temperature (SST) tendency for these two events in the tropical western Pacific and eastern Indian Oceans using satellite-retrieved surface radiative and turbulent fluxes. The radiative fluxes are taken from the Goddard Satellite-retrieved Surface Radiation Budget (GSSRB), derived from radiance measurements of the Japanese Geostationary Meteorological Satellite 5. The GSSRB covers the domain 40 deg S - 4 deg N, 90 deg E-17 deg W and a period from October 1997 to December 2000. The spatial resolution is 0.5 deg x 0.5 deg lat-long and the temporal resolution is 1 day. The turbulent fluxes are taken from Version 2 of the Goddard Satellite-based Surface Turbulent Fluxes (GSSTF-2). The GSSTF-2 has a spatial resolution of 1 deg x 1 deg lat-long over global Oceans and a temporal resolution of 1 day covering the period July 1987-December 2000. Daily turbulent fluxes are derived from the S S M (Special Sensor Microwave/Imager) surface wind and surface air humidity, and the SST and 2-m air temperature of the NCEP/NCAR reanalysis, using a stability-dependent bulk flux algorithm. The changes of surface heat budgets, SST and tendency, cloudiness, wind speed, and zonal wind stress of the 1997/98 El Nino relative to the1998/99 La Nina for the northern winter and spring seasons are analyzed. The relative changes of surface heat budgets and SST tendency of the two events are quite different between the tropical eastern Indian and western Pacific Oceans. For the tropical western Pacific, reduced solar heating (more clouds) is generally associated with decreased evaporative cooling (weaker winds), and vise versa. The changes in evaporative cooling over-compensate that of solar heating and dominate the spatial variability of the changes in net surface heating. Both solar heating and evaporative cooling offset each other to reduce interannual variability of net surface heating. In addition, the area of increased SST tendency is larger than that of increased net surface heating, due to less solar radiation penetration through the bottom of deeper ocean mixed layer (stronger winds). For the tropical eastern Indian Ocean, enhanced solar heating (less clouds) is generally associated with reduced evaporative cooling (weaker winds). Both solar heating and evaporative cooling reinforce each other to increase interannual variability of net surface heating. In addition, the area of increased SST tendency is smaller than that of increased net surface heating in the southern domain. The relative changes in wind and zonal wind stress indicate more solar radiation penetration through the ocean mixed layer and more northward heat transport by Ocean current from the south to the north Indian Ocean for the El Nino than for the La Nina.

Chou, Shu-Hsien↗

NASA's Next Solar Sail: Lessons Learned from NanoSail - D2

NanoSail-D2 unfurled January 17th, 2011 and commenced a nine month Low Earth Orbit path to reentry to evaluate a sail's capacity to deploy in space and deorbit satellites. The orbit was strongly affected by variables including but not limited to: initial attitude, orbit lighting, solar radiation pressure, aerodynamic drag, gravity, and Center of Pressure offsets. The effects of these variables were evaluated through a 3-DOF rigid body simulation. The sail experienced stability in orbits which were continuously lit, i.e. did not orbit behind Earth. Probable drag area experienced by the sail for the mission is also estimated from orbital data and compared to the attitude simulation results. Analysis focuses on sail behavior in full lighting conditions to establish the limits of the sails stability in full lighting. Solar radiation pressure, aerodynamic drag, and gravity torque effects are described. Lastly, a reasonable upper bound on the variation of the Center of Pressure from the geometric center of the sail plane is established. Each of these results contributes to the design requirements for future solar sails.

Katan, Chelsea↗

Internally-heated thermal and externally-cool photovoltaic cascade solar energy system for full solar spectrum utilization

A single-stack, solar power receiver comprising both a thermal absorber layer and a photovoltaic cell layer. The stack includes an aerogel layer, that is optically transparent and thermally insulating ("OTTI"); a spectrally selective high thermal conductivity ("SSTC") thermal absorber layer; a bottom OTTI layer; and a PV cell layer. The SSTC layer includes a set of fins that substantially blocks solar radiation absorption in the band where PV cells are most sensitive. Photons with energies above or below this band block range are absorbed by the fins and the absorbed heat is conducted to pipes in the fin structure carrying a heated thermal working fluid to heat storage. Photons with energy in the band block range are reflected by the SSTC fins to the PV cell layer. The bottom OTTI aerogel layer keeps the PV cell operating near ambient temperature. The PV cell converts incident solar radiation to electrical energy.

14 SOLAR ENERGY↗

Wildfires Dynamics in Siberian Larch Forests

Wildfire number and burned area temporal dynamics within all of Siberia and along a south-north transect in central Siberia (45deg-73degN) were studied based on NOAA/AVHRR (National Oceanic and Atmospheric Administration/ Advanced Very High Resolution Radiometer) and Terra/MODIS (Moderate Resolution Imaging Spectroradiometer) data and field measurements for the period 1996-2015. In addition, fire return interval (FRI) along the south-north transect was analyzed. Both the number of forest fires and the size of the burned area increased during recent decades (p < 0.05). Significant correlations were found between forest fires, burned areas and air temperature (r = 0.5) and drought index (The Standardized Precipitation Evapotranspiration Index, SPEI) (r = 0.43). Within larch stands along the transect, wildfire frequency was strongly correlated with incoming solar radiation (r = 0.91). Fire danger period length decreased linearly from south to north along the transect. Fire return interval increased from 80 years at 62 N to 200 years at the Arctic Circle (6633' N), and to about 300 years near the northern limit of closed forest stands (about 71+ N). That increase was negatively correlated with incoming solar radiation (r = 0.95). Keywords: wildfires; drought index; larch stands; fire return interval; fire frequency; burned area; climate-induced trends in Siberian wildfires

wildfires↗

Study on the reduction of atmospheric mercury emissions from mine waste enriched soils through native grass cover in the Mt. Amiata region of Italy

Atmospheric mercury emissions from mine-waste enriched soils were measured in order to compare the mercury fluxes of bare soils with those from other soils covered by native grasses. Our research was conducted near Mt. Amiata in central Italy, an area that was one of the largest and most productive mining centers in Europe up into the 1980s. To determine in situ mercury emissions, we used a Plexiglas flux chamber connected to a portable mercury analyzer (Lumex RA-915+). This allowed us to detect, in real time, the mercury vapor in the air, and to correlate this with the meteorological parameters that we examined (solar radiation, soil temperature, and humidity). The highest mercury flux values (8000 ng m{sup −2} h{sup −1}) were observed on bare soils during the hours of maximum insulation, while lower values (250 ng m{sup −2} h{sup −1}) were observed on soils covered by native grasses. Our results indicate that two main environmental variables affect mercury emission: solar radiation intensity and soil temperature. The presence of native vegetation, which can shield soil surfaces from incident light, reduced mercury emissions, a result that we attribute to a drop in the efficiency of mercury photoreduction processes rather than to decreases in soil temperature. This finding is consistent with decreases in mercury flux values down to 3500 ng m{sup −2} h{sup −1}, which occurred under cloudy conditions despite high soil temperatures. Moreover, when the soil temperature was 28 °C and the vegetation was removed from the experimental site, mercury emissions increased almost four-fold. This increase occurred almost immediately after the grasses were cut, and was approximately eight-fold after 20 h. Thus, this study demonstrates that enhancing wild vegetation cover could be an inexpensive and effective approach in fostering a natural, self-renewing reduction of mercury emissions from mercury-contaminated soils. -- Highlights: ► Mercury air/surface exchange from grass covered soil is different from bare soil. ► Light enhances mercury emissions and is the main parameter driving the process. ► The presence of wild vegetation covering the soil reduces mercury emission. ► Vegetative covers could be a solution to reduce atmospheric mercury pollution.

54 ENVIRONMENTAL SCIENCES↗

Tracking and Data Relay Satellite (TDRS) tracking and orbit determination

Analysis results were derived using the Goddard Trajectory Determination System to determine the orbit of TDRS-East. A batch weighted least-squares algorithm is used to fit the Bilateration Ranging Transponder system tracking measurements. Six state parameters (position and velocity components) and the solar radiation pressure coefficient are estimated. The solutions are obtained by fitting the data over 34 hr arcs that overlap by 10 hr. Ephemerides are generated over the 34 hr arcs and then compared over the overlapping regions. The position differences indicate the consistency of the solutions and give a measure of their accuracy. The effect of the modeling of perturbative forces (solar radiation pressure, nonspherical geopotential field) on these results are studied. Error analysis is performed using the ORAN program to estimate the effect of force-model errors and measurement-related errors on the TDRS-East ephemeris.

Teles, J.↗