Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STAINLESS STEELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

RF-sputtered silicon and hafnium nitrides - Properties and adhesion to 440C stainless steel

Silicon nitride and hafnium nitride coatings were deposited by reactive RF sputtering on oxidized and unoxidized 440C stainless steel substrates. Sputtering was done in mixtures of argon and nitrogen gases from pressed powder silicon nitride and from hafnium metal targets. Depositions were at two background pressures, 8 and 20 mtorr, and at two different fractions (f) of nitrogen in argon, 0.25 and 0.60, for hafnium nitride and at f = 0.25 for silicon nitride. The coatings and the interface between the coating and substrates were investigated by X-ray diffractometry, scanning electron microscopy, energy dispersive X-ray analysis and Auger electron spectroscopy. A Knoop microhardness of 1650 + or 100 kg/sq mm was measured for hafnium nitride and 3900 + or 500 kg/sq mm for silicon nitride. The friction coefficients between a 440C rider and the coatings were measured under lubricated conditions. Scratch test results demonstrate that the adhesion of hafnium nitride to both oxidized and unoxidized 440C is superior to that of silicon nitride. Oxidized 440C is found to have increased adhesion, to both nitrides, over that of unoxidized 440C.

Grill, A.↗

Proof Testing Of Stainless-Steel Bolts

Report describes study of development of method for nondestructive proof testing of bolts made of A286 stainless steel. Based on concept that the higher load bolt survives, the smaller the largest flaw and, therefore, the longer its fatigue life after test. Calculations and experiments increase confidence in nondestructive proof tests.

Hsieh, Cheng H.↗

Tribological behavior of 440C martensitic stainless steel from -184 C to 750 C

Characterization of the coefficient of friction and wear rate of 440C stainless steel is needed to understand the effects of frictional heating in the bearings of the High Pressure Oxygen Turbopump of the Space Shuttle Main Engine. The coefficient of friction and wear rate have been measured over a range of temperature varying from liquid oxygen temperature (-184 C) to 750 C. The normal load has also been varied resulting in a variation of Hertzian stress from 0.915 to 3.660 GPa while the surface velocity has been varied from 0.5 to 2.0 m/s.

Slifka, A. J.↗

Corrosion Behavior of Stainless Steel 304 and Nickel 625 Under Iodine Vapor at 300 °C

The chemical, structural, and microstructural behavior of stainless steel 304 (SS 304) and nickel 625 (Ni 625) were probed after exposure to iodine vapor laminar flow at 300 °C. This work was conducted in support of the development of in-space propulsion utilizing iodine as a propellant. The kinetics of corrosion was measured in a custom-built iodine-compatible thermogravimetric analyzer rig at 300 °C in which samples were exposed to an iodine laminar vapor flow of 1 mg/min (carried by 20 mL/min argon gas) for up to 31 days. Samples were characterized after the experiment by X-ray diffraction, electron microscopy, energy dispersive X-ray spectroscopy, and dynamic secondary ion mass spectrometry. All samples formed scales consisting mainly of metal oxyiodides showing different chemistry, microstructure, and crystalline phases. The paralinear rate law best describes the kinetics of oxidation of the samples. SS 304 exhibited slightly slower kinetics of oxidation (106±3·10(exp –5) mg/sq.cm/day) than Ni 625 (122±3·10(exp –5) mg/sq.cm/day) in the low-oxygen and low-water environment.

Chemistry and Materials↗

Effect of thermal aging on oxide film of stainless steel weld overlay cladding exposed to high temperature water

Highlights: • Oxide film of aged cladding material in high temperature water was studied. • Thermal aging contributed to high corrosion susceptibility of the ferrite phase. • Highly corrosion of aged ferrite phase was caused by spinodal decomposition. • Carbides along phase boundary facilitated the corrosion of the cladding material. - Abstract: Characteristics of the oxide film formed on stainless steel weld overlay cladding aged at 400 °C for different times in high temperature water were studied. The results showed that thermal aging showed no obvious effect on the volume fraction of ferrite phase but resulted in high corrosion susceptibility of the aged ferrite phase mainly. The oxide film formed on the unaged cladding material consisted of 100-nm-thick inner oxide layer (FeCr{sub 2}O{sub 4} and Cr{sub 2}O{sub 3}) and Fe-rich outer oxide particles (Fe{sub 3}O{sub 4}) with a size of 2 O4, Cr{sub 2}O{sub 3} and Fe{sub 3}O{sub 4}) and outer oxide particles (Fe{sub 3}O{sub 4} and FeCr{sub 2}O{sub 4}) with a size of <700 nm formed on the aged ferrite phase. Spinodal decomposition was considered as the main factor to promote the corrosion of the aged ferrite phase, and existence of carbides along phase boundary facilitated corrosion of the cladding material in high temperature water.

36 MATERIALS SCIENCE↗

Note: Electrostatic detection of stainless steel dust particles for fusion applications

Dust accumulation inside next-step fusion devices poses a significant safety concern and dust diagnostics will be needed to assure safe operations. An electrostatic dust detection device has been successfully demonstrated in the National Spherical Torus Experiment, Tore Supra, and the Large Helical Device, and the detector's response to carbon particles was previously characterized in laboratory experiments. This paper presents laboratory results showing that detection of stainless steel particles at levels as low as several μg/cm{sup 2} is also possible.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Chemical cleaning of porous stainless steel cross-flow filter elements for nuclear waste applications

The Waste Treatment and Immobilization Plant (WTP) currently under construction for treatment of High-Level Waste (HLW) at the Hanford Site will rely on cross-flow ultrafiltration to provide solids-liquid separation as a core part of the treatment process. To optimize process throughput, periodic chemical cleaning of the porous stainless steel filter elements has been incorporated into the design of the plant. It is currently specified that chemical cleaning with nitric acid will occur after significant irreversible membrane fouling is observed. Irreversible fouling is defined as fouling that cannot be removed by backpulsing the filter. PNNL has investigated chemical cleaning processes as part of integrated tests with HLW simulants and with actual Hanford tank wastes. To quantify the effectiveness of chemical cleaning, the residual membrane resistance after cleaning was compared against the initial membrane resistance for each test in a series of long-term fouling tests. The impact of the small amount of residual resistance in these tests could not be separated from other parameters and the historical benchmark of >1 GPM/ft2 for clean water flux was determined to be an adequate metric for chemical cleaning. Using the results from these tests, a process optimization strategy is presented suggesting that for the simulant material under test, the value of chemical cleaning may be suspect. The period of enhanced filtration may not be enough to offset the down time required for chemical cleaning, without respect to the other associated costs.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Manufacture of Alumina-Forming Austenitic Stainless Steel Alloys by Conventional Casting and Hot-Working Methods

Oak Ridge National Laboratory (ORNL) and Carpenter Technology Corporation (CarTech) participated in an in-kind cost share cooperative research and development agreement (CRADA) effort under the auspices of the Energy Efficiency and Renewable Energy (EERE) Technology Maturation program to explore the feasibility for scale up of developmental ORNL alumina-forming austenitic (AFA) stainless steels by conventional casting and rolling techniques. CarTech successfully vacuum melted 30lb heats of four AFA alloy compositions in the range of Fe-(20-25)Ni-(12-14)Cr-(3-4)Al-(1-2.5)Nb wt.% base. Conventional hot/cold rolling was used to produce 0.5-inch thick plate and 0.1-inch thick sheet product. ORNL subsequently successfully rolled the 0.1-inch sheet to 4 mil thick foil. Long-term oxidation studies of the plate form material were initiated at 650, 700, and 800 C in air with 10 volume percent water vapor. Preliminary results indicated that the alloys exhibit comparable (good) oxidation resistance to ORNL laboratory scale AFA alloy arc casting previously evaluated. The sheet and foil material will be used in ongoing evaluation efforts for oxidation and creep resistance under related CRADAs with two gas turbine engine manufacturers. This work will be directed to evaluation of AFA alloys for use in gas turbine recuperators to permit higher-temperature operating conditions for improved efficiencies and reduced environmental emissions.

36 MATERIALS SCIENCE↗

Investigation of MO x (M = Cr, Mn, Re, and Mo) coated stainless-steel electrodes for oxygen evolution reaction in natural seawater electrolysis

Seawater electrolysis is considered a potential strategy for large-scale of affordable H 2 production. However, poor durability of the anode for oxygen evolution reaction (OER) in natural seawater is a remaining concern due to chloride-induced reaction. Herein, the effect of various MO x (M = Mn, Cr, Re, and Mo) coated stainless steel (SS) electrodes on OER in direct natural seawater electrolysis was comprehensively studied. It is found that the Mo-coated SS electrode is superior to all others in terms of durability, followed by Re-coated SS, while the Cr and Mn-coated SS electrodes show the poorest durability. Additionally, the durability and activity of the Mo/SS electrode can be boosted remarkably in 1 M KOH/seawater compared to the natural seawater, resulting in an overpotential at 10 mA cm −2 decrease from 830 to 399 mV. Meanwhile, no degradation is observed at 1000 mA cm −2 for 100 h in 1 M KOH seawater, which is among the best stability, based on the literature review. Moreover, the improved durability and activity with Mo coating were extended to the Inconel 718 substrate, and around 40 % improvement in durability and 25 mV overpotential decrease at 10 mA cm −2 are observed, which indicates that Mo coating can be considered as a universal approach to improve the anode durability and activity. The improved performance with Mo coating may be attributed to the continuous Mo oxide layer formation or in situ generated MoO 4 2− in the OER process. In conclusion, this work provides a holistic strategy to enhance the anode durability and activity under harsh conditions, offering valuable insights for designing corrosion-resistant electrodes in direct seawater electrolysis.

Direct seawater electrolysis↗

Post-build stress-relief optimization for laser powder bed fusion 316H stainless steel

Nuclear energy remains a critical component of a diversified and efficient energy portfolio, offering reliable, high-capacity, and low-carbon power. However, in the U.S., aging infrastructure and the slow qualification and deployment of advanced materials and manufacturing techniques hinder progress in next-generation reactor technologies. This study explores the application of laser powder bed fusion (LPBF) additive manufacturing for stainless steel 316H, with a focus on optimizing post-build heat treatments to enhance material properties for high-temperature nuclear applications. The research targets the optimization of stress-relief temperatures to alleviate postbuild residual stresses, ensuring improvements in the microstructural corelated properties. A series of microstructural and mechanical evaluations were performed on LPBF-printed SS-316H samples which were subjected to annealing at temperatures varying between 650 °C and 850 °C. X-ray diffraction, scanning electron microscopy, and transmission electron microscopy analyses revealed that increasing the heattreatment temperature accelerated dislocation recovery. Vickers microhardness measurements showed an initial reduction in values, followed by stabilization over extended durations at all the temperatures. While higher temperatures facilitated faster recovery, they also promoted carbide precipitation along grain and solidification cell boundaries, narrowing the safe processing window. In contrast, heat treatment at 650°C preserved the cellular substructure and enabled controlled carbide precipitation over time. In conclusion, these findings highlight the importance of time–temperature optimization and suggest that 650°C for up to 2 h provides the most favorable balance between recovery and carbide control for a stress-relief treatment.

316 stainless steel↗

DETERMINATION OF THE SOLID-STATE RESISTANCE-WELDABILITY OF ADDITIVELY MANUFACTURED 304L STAINLESS STEEL

Additive manufacturing of pressure-containing boundaries is of interest to numerous industries, so a project was initiated to develop several different methods to join and weld additively manufactured materials. The approach investigated in this study was a low energy, solid state spot weld. This general approach has been routinely used for conventionally prepared tubing and is now being expanded to additively manufactured components. Additively manufactured 304L stainless steel sheets, semi-tubes, and tubes were resistance spot welded and compared to comparable welds in conventionally manufactured tubing. Radiographic computed tomography and metallography were used to evaluate the suitability of the welds using three criteria: weld closure length, thickness, and width. All additively manufactured test welds closely matched the conventional tubing for these criteria

additive manufacturing↗

Microstructure and texture evolution of duplex stainless steels with different molybdenum contents

Highlights: • The 3.05Mo steel has higher resistance to strain-induced transformation than the 0.28Mo steel. • The increased Mo content affects the grain growth of austenite and ferrite due to the effects of segregation and anchoring. • At high annealing temperatures, this Mo retarding effect is weakened. • The suppression of γ-fiber development in the ferrite texture is associated with the increased Mo content. • High amounts of Mo generate unfavorable conditions for the formation of CSL boundaries. - Abstract: The microstructure and texture evolution of duplex stainless steels with different molybdenum contents were studied. For this purpose, hot-rolled 2205 and 2304 samples were solution-annealed at 1100 °C for 1800 s and then cold-rolled to a 75% thickness reduction. This was followed by an isothermal annealing at 900 and 1100 °C for 180 s. The EBSD technique was used to determine the phase ratio, crystallographic texture, and microstructural characteristics. The hot-rolled steel had a work hardened microstructure and the samples submitted to intermediate annealing presented mainly deformation-free grains. Cold rolling resulted in a substantial reduction in the phase spacing with the formation of the strain-induced α′-martensite (SIM) from the metastable austenite. After annealing at 900 °C, the ferrite grains retained the elongated shape of the cold-rolled condition and the primary recrystallization progressed in the austenite phase. Increasing the Mo content increased the resistance to strain-induced martensitic transformation and inhibited the grain growth of austenite phase during annealing at 900 °C. Increasing annealing temperature to 1100 °C promoted the coarsening of both bcc and fcc structures with the formation of annealing twins in the austenitic grains. The recrystallization kinetics and subsequent grain growth occur earlier in ferrite than in austenite phase. Differences in Mo content did not significantly alter the evolution of austenite texture, whereas in the ferrite phase the increase in Mo content suppressed the γ-fiber development. Oriented nucleation was the predominant mechanism observed during the recrystallization of ferritic grains in the 2205 samples. The development of ∑19a boundaries was associated with the selected growth of {554}<225>{sub α} grains in the annealed 2304 samples. Annealing twins were associated with the formation of Σ3 boundaries after the heat treatments. Grain coarsening resulted in a larger fraction of the special boundaries in ferrite phase but inhibited the CSL formation in the austenite phase.

36 MATERIALS SCIENCE↗

Investigation of Iron-Chromium-Niobium-Titanium Ferritic Stainless Steel for Solid Oxide Fuel Cell Interconnect Applications

As part of an effort to develop cost-effective ferritic stainless steel-based interconnects for solid oxide fuel cell (SOFC) stacks, AL 441 HPTM was studied in terms of its metallurgical characteristics, oxidation behavior, and electrical performance. Minor alloying elements (Nb and Ti) captured interstitials such as C by forming carbides, stabilizing the ferritic structure and mitigating the risks of sensitization and inter-granular corrosion. Laves phases rich in Nb and Si precipitated along grain boundaries during high temperature exposure, improving the steel’s high temperature mechanical strength. The capture of Si in the Laves phase minimized the Si activity in the steel substrate and prevented formation of an insulating silica layer at the scale/metal interface. However, the relatively high oxidation rate, and thus increasing ASR over time, necessitates the application of a conductive protection layer on the steel. In particular, Mn1.5Co1.5O4 spinel protection layers drastically improved the electrical performance of the ferritic stainless steel 441, acting as barriers to chromium outward and oxygen inward diffusion.

Solid oxide fuel cell, interconnect, oxidation, co↗

Effects of Nb/Ti/V/Ta on phase precipitation and oxidation resistance at 1073 K in alumina-forming austenitic stainless steels

Highlights: • Effects of Nb/Ti/V/Ta on phase precipitation at 1073 K in AFA alloys are studied. • The precipitation of σ-FeCr can be accelerated by the formation of B2-NiAl. • The additions of V and Ta can improve the oxidation resistance of AFA alloys. • The precipitation of σ-FeCr will deteriorate the oxidation resistance. • Good performance can be achieved by M co-alloying and an appropriate M/C ratio. - Abstract: The present work investigated the effects of strong carbide-forming elements M (M = Nb, Ti, V, Ta) on the phase precipitation and oxidation resistance at 1073 K in alumina-forming austenitic (AFA) stainless steels (Fe-20Ni-(18–23)Cr-2.5Al-2.3Mo-0.08C-Nb/Ti/V/Ta wt%). The designed alloy rods were solid-solutioned at 1523 K for 1.5 h, and then aged at 1073 K for 24 h or oxidized at 1073 K for 500 h, respectively. Besides primary MC carbides, B2-NiAl, Fe{sub 2}M, and σ-FeCr phases would be precipitated from the γ-austenitic matrix in these aged AFA alloys. Furthermore, the precipitation of σ-FeCr could be accelerated by the B2-NiAl formation, which is related to the γ stability. The formation of MC and Fe{sub 2}M can be controlled via adjusting the ratio of M/C. The oxidation resistance of these AFA alloys can be improved effectively by V and Ta addition due to the formation of compact Al{sub 2}O{sub 3} protective scales. This work will provide a new approach to obtain a good combination of creep strength and oxidation resistance through co-alloying with Nb/Ta/V and controlling the M/C ratio within 1.0–2.0 (in molar ratio) simultaneously.

36 MATERIALS SCIENCE↗

Effect of processing parameters and build orientation on microstructure and performance of AISI stainless steel 304L made with selective laser melting under different strain rates

Selective laser melting (SLM) process brings diverse potentials on geometry flexibility; therefore, it is more and more widespread to be employed in fabrication metal alloys served for industries. Nonetheless, a material characterization study is desired to carry on for better understanding the correlation among process, structure, microstructure, and performance. In the current study, the SLM fabricated AISI stainless steel 304L was fabricated with different process parameters and built orientations (horizontal, inclined, and vertical. The tensile behavior was evaluated under different strain rates (0.0001 /s, 0.001 /s, 0.01 /s, and 0.1 /s) and compared to the commercial cold-rolled and annealed counterpart. Grain structures, tensile strength, elongation-to-failure, strain rate sensitivity, work hardening, and fractographic analysis were evaluated in terms of the effect of energy density, build orientation, and strain rate. The output indicates the tensile strength increases with increasing strain rates. On the contrary, the elongation-to-failure shows a decreasing trend with strain rates. Tensile properties of specimens built in the horizontal and inclined orientations are more sensitive to strain rates due to the smaller dimension of grain structures. Tensile anisotropy depends on the energy input, where a high energy density could yield a strong build orientation-dependent anisotropy. Hall-Petch relationship is validated to explain the mechanical anisotropy in different built orientations for SLM alloys. The strain hardening exponent and work hardening rate are demonstrated to be positively correlated, and they increase with smaller grain sizes. The fine dimple features indicate the ductile fracture mode regardless of strain rates. The size of the ductile dimples seems to depend on the strain rates and build orientations.

36 MATERIALS SCIENCE↗

Catastrophic oxidation mechanism of hyper duplex stainless steel S32707 at high temperature in air

Highlights: • High temperature oxidation behavior and mechanism of S32707 were investigated in air. • MoO{sub 3}, molten molybdate and precipitate jointly cause catastrophic oxidation at 900 °C. • Air-nitriding plays an important role in accelerating oxidation at 1000 and 1100 °C. • Synergism of MoO{sub 3}, molten molybdate and nitriding promotes catastrophic oxidation. • Disappearance of MoO{sub 3}, molybdate and nitriding enhances oxidation resistance at 1200 °C. - Abstract: High-temperature oxidation behavior and the mechanism of hyper duplex stainless steel S32707 were investigated at 900, 1000, 1100 and 1200 °C in air. Some interesting oxidation characteristics were observed, and the corresponding oxidation mechanisms were proposed. At 900 °C, oxidation follows a linear rate law. The combined actions of MoO{sub 3} volatilization, molten molybdate dissolution reaction and block-like σ phase and Cr{sub 2}N precipitation cause catastrophic oxidation. When the temperature is raised to 1000 and 1100 °C, the deleterious effects of MoO{sub 3} and molten molybdates are greatly enhanced. Moreover, undesirable air-nitriding occurs and further accelerates the oxidation. The synergistic effects of MoO{sub 3} volatilization, molten molybdate dissolution reaction and air-nitriding strongly promote catastrophic oxidation. Surprisingly, the oxidation at 1200 °C follows a near-parabolic rate law. The disappearances of MoO{sub 3}, molten molybdates and air-nitriding lead to the formation of a rather compact, complete and protective oxide layer. The oxidation resistance of the steel has been clearly improved.

36 MATERIALS SCIENCE↗

Effect of grain boundary character distribution on weld heat-affected zone liquation cracking behavior of AISI 316Ti austenitic stainless steel

Highlights: • Grain boundary engineered AISI 316 was produced through thermomechanical processing. • Grain boundary engineering resulted in random high angle boundary network disruption. • Liquation cracks are arrested at triple junctions having one or more CSL boundaries. • Grain boundary engineering resulted in improvement in liquation cracking resistance. - Abstract: In this work, the role of grain boundary engineering (GBE) on the weld heat-affected-zone (HAZ) liquation cracking resistance of austenitic stainless steel AISI 316Ti was investigated. Standard wrought-processed alloy 316Ti was cold rolled to 5% strain and subsequently annealed at 1373 K for 30 min to achieve the optimum grain boundary character distribution (GBCD). The GBE samples were found to consist of a significantly higher fraction (72%) of low Ʃ coincident site lattice (CSL) boundaries as compared to the as received (AR) samples (45%). To study the liquation cracking behavior, single-track longitudinal varestraint tests was performed on AR and GBE samples. Microstructural examination revealed that the grain coarsening and the liquation events were less prominent in the GBE samples as compared to the AR samples. It is believed that the reduced segregation of impurities to the special boundaries (coherent Ʃ3 twins, in particular) present in the GBE samples is responsible for the observed improvement in the HAZ liquation cracking resistance.

36 MATERIALS SCIENCE↗

CRADA No. NFE-10-02715 Assessment of AFA Stainless Steels for Tube Products in Chemical Processing and Energy Production Applications

Oak Ridge National Laboratory (ORNL) and Carpenter Technology Corporation (Carpenter) participated in an in-kind cost share cooperative research and development agreement (CRADA) effort under the auspices of the Energy Efficiency and Renewable Energy (EERE) Technology Maturation Program to assess material properties of several potential AFA family grades and explore the feasibility of producing alumina-forming austenitic (AFA) stainless steels in tubular form needed for many power generation and chemical process applications. Carpenter's Research Laboratory successfully vacuum melted 30 lb heats of seven candidate AFA alloy compositions representing a wide range of alloy content and intended application temperatures. These compositions were evaluated by ORNL and Carpenter R&D for microstructure, tensile properties, creep properties, and oxidation resistance. In parallel, additional work was directed toward an initial tube manufacture demonstration of a baseline AFA alloy. Carpenter successfully manufactured a 10,000 lb production heat and delivered appropriate billets to a partner for extrusion evaluation. Tube product was successfully manufactured from the baseline AFA alloy, indicating good potential for commercially produced AFA tubular form material.

36 MATERIALS SCIENCE↗