Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SOOT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Comparison of RCCI Operation with and without EGR over the Full Operating Map ofa Heavy-Duty Diesel Engine

Dual-fuel combustion using port-injection of low reactivity fuel combined with direct injection of a higher reactivity fuel, otherwise known as Reactivity Controlled Compression Ignition (RCCI), has been shown as a method to achieve high efficiency combustion with moderate peak pressure rise rates, low engine-out soot and NOx emissions. A key requirement for extending to high-load operation is reduce the reactivity of the premixed charge prior to the diesel injection. One way to accomplish this is to use a very low reactivity fuel such as natural gas. In this work, experimental testing was conducted on a 13L multi-cylinder heavy-duty diesel engine modified to operate using RCCI combustion with port injection of natural gas and direct injection of diesel fuel. Natural gas/diesel RCCI engine operation is compared over the EPA Heavy-Duty 13 mode supplemental emissions test with and without EGR. Emissions and efficiency metrics were examined over the entire engine map for both operating modes. It was found that the use of EGR lowered combustion noise to less than 97 dBa and lowered the cycle averaged NOx emissions by 48%, with only a slight increase in soot and 0.5 point decrease in brake thermal efficiency. Thus, operation with EGR offered the lowest total fluid consumption when considering the use of a selective catalytic reduction system for NOx aftertreatment.

Hanson, Reed↗

Numerical Methodology for Optimization of Compression-Ignited Engines Considering Combustion Noise Control

It is challenging to develop highly efficient and clean engines while meeting user expectations in terms of performance, comfort, and drivability. One of the critical aspects in this regard is combustion noise control. Combustion noise accounts for about 40 percent of the overall engine noise in typical turbocharged diesel engines. The experimental investigation of noise generation is difficult due to its inherent complexity and measurement limitations. Therefore, it is important to develop efficient numerical strategies in order to gain a better understanding of the combustion noise mechanisms. In this work, a novel methodology was developed, combining computational fluid dynamics (CFD) modeling and genetic algorithm (GA) technique to optimize the combustion system hardware design of a high-speed direct injection (HSDI) diesel engine, with respect to various emissions and performance targets including combustion noise. The CFD model was specifically set up to reproduce the unsteady pressure field inside the combustion chamber, thereby allowing an accurate prediction of the acoustic response of the combustion phenomena. The model was validated by simulating several steady operating conditions and comparing the numerical results against experimental data, in both temporal and frequency domains. Thereafter, a GA optimization was performed with the goal of minimizing indicated specific fuel consumption (ISFC) and combustion noise, while restricting pollutant (soot and NOx) emissions to their respective baseline values. Eight design variables were selected pertaining to piston bowl geometry, nozzle inclusion angle, number of injector nozzle holes, and in-cylinder swirl. An objective merit function (MF) based on the emissions, ISFC, and combustion noise was constructed to quantify the strength of the engine designs and was determined using the CFD model as the function evaluator. The in-cylinder noise level was characterized by the total resonance energy of local pressure oscillations. The optimum engine configuration thus obtained showed a significant improvement in terms of efficiency and combustion noise compared to the baseline system, along with both soot and NOx emissions within their respective constraints. This optimum configuration included a deeper and tighter bowl geometry with higher swirl and larger number of nozzle holes. Subsequently, a more detailed acoustics analysis based on proper orthogonal decomposition (POD) technique was carried out to further explore the combustion noise benefits achieved by the GA optimum. In conclusion, this computational study is a first of its kind (to the best of the authors’ knowledge), which demonstrates a comprehensive framework to incorporate combustion noise into a numerical optimization strategy for engine design.

42 ENGINEERING↗

Ignition Delay in Low Temperature Combustion

Low temperature combustion (LTC) strategies present a means of reducing soot and oxides of nitrogen (NOx) emissions while simultaneously increasing efficiency relative to conventional combustion modes. By sufficiently premixing fuel and air before combustion, LTC strategies avoid high fuel-to-air equivalence ratios that lead to soot production. Dilution of the mixture lowers the combustion temperatures to reduce NOx production and offers thermodynamic advantages for improved efficiency. However, issues such as high heat release rates (HRRs), incomplete combustion, and difficulty in controlling the timing of combustion arise with low equivalence ratios and combustion temperatures. Ignition delay (the time until the start of combustion) is a way to quantify the time available for fuel and air to mix inside the cylinder before combustion. Previous studies have used ignition delay to explain trends seen in LTC such as combustion stability and HRRs. This study provides a novel method of integrating ignition delay into the investigation of LTC to determine what insights ignition delay calculations can provide for the different challenges associated with LTC strategies. To eliminate the need for large chemical kinetic models and interpolation to predict ignition delay, an ignition delay correlation is used. The flexibility gained using the correlation allows this method to be quickly adapted to target different LTC strategies and challenges. In this work, three cases of low temperature gasoline combustion (LTGC) with varying stratification levels were evaluated with an emphasis on the non-monotonic trend of the HRRs. The described method for ignition delay calculation is used to detail the stratification and ignition delay distributions for each case and provide insight into the observed trends.

Drallmeier, Joseph↗

Mixing-limited Combustion of Alcohol Fuels in a Diesel Engine

Diesel-fueled, heavy-duty engines are critical to global economies, but unfortunately they are currently coupled to the rising price and challenging emissions of Diesel fuel. Public awareness and increasingly stringent emissions standards have made Diesel OEMs consider possible alternatives to Diesel, including electrification, fuel cells, and spark ignition. While these technologies will likely find success in certain market segments, there are still many applications that will continue to require the performance and liquid-fueled simplicity of Diesel-style engines. Three-way catalysis represents a possible low-cost and highly-effective pathway to reducing Diesel emissions, but that aftertreatment system has typically been incompatible with Diesel operation due to the prohibitively high levels of soot formation at the required stoichiometric fuel-air ratios. This paper explores a possible method of integrating three-way catalysis with Diesel-style engine operation. The proposed concept utilizes a high-temperature combustion system-enabled by a combination of thermal insulation, reduced turbocharger aftercooling, and exhaust gas retention-to combust low-cetane “sootless” fuels like ethanol, methanol, and natural gas in a traditional Diesel-style combustion mode (i.e. mixing-limited diffusive combustion, rather than HCCI-like strategies). The proposed concept has demonstrated the ability to meet EPA 2010 soot emissions limits without a particulate filter, while also maintaining a stoichiometric exhaust composition that is compatible with three-way catalysis. Further, the proposed concept can meet, and even exceed, baseline Diesel engine efficiency by combining the high compression ratio Diesel engine design with reduced heat transfer losses. Finally, use of mixing-limited, Diesel-style combustion drastically simplifies combustion phasing, and limits rate of rise. These early results motivate additional work on this concept, further optimizing components for high-temperature operation on alcohol fuels, and integrating the results into a commercial multi-cylinder engine demonstration.

Blumreiter, Julie↗

Effects of Fuel Properties on Particle Number and Particle Mass Emissions from Lean and Stoichiometric Gasoline Direct Injection Engine Operation

Engine-out particle size distributions and soot mass emissions were measured from a gasoline direct injection (GDI) engine fueled by seven different gasoline formulations. Additionally, particle size distributions were simultaneously measured downstream of a catalyzed gasoline particulate filter (GPF) to determine the size resolved filtration efficiency. Stoichiometric, lean homogeneous, and lean stratified combustion modes were studied at four steady-state engine conditions. The particulate matter (PM) Index was calculated for each fuel as a function of the double bond equivalent and vapor pressure of the fuel components. There was generally poor correlation between particle number (PN)/PM mass emissions and the PM Index for steady state stoichiometric conditions with clean injectors, which emitted low particle concentrations. However, under high-load lean homogeneous conditions, there was good correlation between PN/PM mass emission and the PM Index, with the exception that the high ethanol content fuel produced significantly higher PM emissions than the other fuels. Under lean stratified conditions, most fuels produced similar particle size distributions and concentrations with the exception that the E50 fuel produced significantly lower concentrations than the other fuels. These results demonstrate the profound sensitivity of particle emissions from high ethanol content fuel to engine operating conditions. Additionally, these results show the predominant factor influencing particle formation is charge mixture formation, which fuel properties influence, but not as significantly as engine conditions. Here, the GPF reduced the tailpipe particle number concentrations by 60 - 95% and showed evidence of passive regeneration under higher load lean engine conditions (Temp>400°C, Lambda>1.3). Total PN filtration efficiencies ranged from ~60 % with a clean filter to greater than 95% with as little as 25 mg/L of soot loaded on the filter with a most penetrating particle size (MPPS) between 100 and 150 nm. The GPF results show that GPF regeneration can be achieved with the added fuel efficiency benefit of lean operation.

33 ADVANCED PROPULSION SYSTEMS↗

Characterization of Particulate Matter Emissions from Heavy-Duty Partially Premixed Compression Ignition with Gasoline-Range Fuels

In this study, the compression ratio of a commercial 15L heavy-duty diesel engine was lowered and a split injection strategy was developed to promote partially premixed compression ignition (PPCI) combustion. Various low reactivity gasoline-range fuels were compared with ultra-low-sulfur diesel fuel (ULSD) for steady-state engine performance and emissions. Specially, particulate matter (PM) emissions were examined for their mass, size and number concentrations, and further characterized by organic/elemental carbon analysis, chemical speciation and thermogravimetric analysis. As more fuel-efficient PPCI combustion was promoted, a slight reduction in fuel consumption was observed for all gasoline-range fuels, which also had higher heating values than ULSD. Since mixing-controlled combustion dominated the latter part of the combustion process, hydrocarbon (HC) and carbon monoxide (CO) emissions were only slightly increased with the gasoline-range fuels. In contrast, soot emissions were significantly reduced with the gasoline-range fuels, including a ~70% reduction in micro soot sensor measurements and a >50% reduction in smoke meter measurements. All gasoline-range fuel PM samples were also found to contain higher amount of volatile species and organic carbon fractions compared to ULSD PM samples as measured by thermogravimetric and EC-OC analyses. Various partially oxidized HC species and nitrophenolic compounds were also detected by TDP-GC-MS and CE-MS techniques, which implied that more pronounced PPCI combustion occurred with the gasoline-range fuels. As a whole similar PM oxidation behavior was observed despite the differences in reactivity and chemical properties of the fuels, even though there may be some significant impacts under certain operating conditions.

33 ADVANCED PROPULSION SYSTEMS↗

Measurement report: The Fifth International Workshop on Ice Nucleation phase 1 (FIN-01): intercomparison of single-particle mass spectrometers

Knowledge of the chemical composition and mixing state of aerosols at a single-particle level is critical for gaining insights into atmospheric processes. One common tool to make these measurements is single-particle mass spectrometry. There remains a need to compare the performance of different single-particle mass spectrometers (SPMSs). An intercomparison of SPMSs was conducted at the Aerosol Interaction and Dynamics in the Atmosphere (AIDA) chamber at the Karlsruhe Institute of Technology (KIT) in November 2014, as part of the first phase of the Fifth International Workshop on Ice Nucleation (FIN-01). In this paper we compare size distributions and mass spectra of atmospherically relevant particle types measured by five SPMSs. These include different minerals, desert and soil dusts, soot, bioaerosol (Snomax; protein granule), secondary organic aerosol (SOA), and SOA-coated mineral particles. Most SPMSs reported similar vacuum aerodynamic diameter (d va ) within typical instrumental ranges from ~100–200 nm (lower limit) to ~2–3 µm (upper limit). In general, all SPMSs exhibited a wide dynamic range (up to ~10 3 ) and high signal-to-noise ratio (up to ~10 4 ) in mass spectra. Common spectral features with small diversities in mass spectra were found with high average Pearson's correlation coefficients, i.e., for average positive spectra r avg-pos =0.74 ± 0.12 and average negative spectra r avg-neg =0.67 ± 0.22. We found that instrument-specific detection efficiency (DE) was more dependent on particle size than particle type, and particle identification favored the use of bipolar, rather than monopolar, instruments. Particle classification from “blind experiments” showed that all instruments differentiated SOA, soot, and soil dust and detected subtle changes in the particle internal mixing but had difficulties differentiating among specific mineral types and dusts. This study helps to further understand the capabilities and limitations of the single-particle mass spectrometry technique in general and the specific performance of the instrument in characterizing atmospheric aerosol particles.

54 ENVIRONMENTAL SCIENCES↗

sp2 (00)

The single-particle soot photometer (SP2) measures the soot (black carbon) mass of individual aerosol particles by laser-induced incandescence down to concentrations as low as ng/m^3. The SP2 is part of the aerosol observing system (AOS).

54 ENVIRONMENTAL SCIENCES↗

Adelphi-Goddard emulsified fuel project

Thermal efficiency and particle emissions were studied using water/oil emulsions. These studies were done using number 2 and number 6 fuel oil. The number 6 oil had a sulfur content greater than one percent and experiments were conducted to remove the sulfur dioxide from the stack gases. Test findings include: (1) emulsion effected a reduction in soot at a low excess air levels; (2) a steam atomizing system will produce a water/oil emulsion. The fuel in the study was emulsified in the steam atomization process, hence, pre-emulsification did not yield a dramatic reduction in soot or an increase in thermal efficiency.

Source record↗

Photographic combustion characterization of LOX/hydrocarbon type propellants

Single element injectors and two fuels were tested with the aim of photographically characterizing observed combustion phenomena. The three injectors tested were the O-F-O triplet, the transverse like on like (TLOL), and the rectangular unlike doublet (RUD). The fuels tested were RP-1 and propane. The hot firings were conducted in a specifically constructed chamber fitted with quartz windows for photographically viewing the impingement spray field. All LOX/HC testing demonstrated coking with the RP-1 fuel leaving far more soot than the propane fuel. No fuel freezing or popping was experienced under the test conditions evaluated. Carbon particle emission and combustion light brilliance increased with Pc for both fuels although RP-1 was far more energetic in this respect. The RSS phenomena appear to be present in the high Pc tests as evidenced by striations in the spray pattern and by separate fuel rich and oxidizer rich areas. The RUD element was also tested as a fuel rich gas generator element by switching the propellant circuits. Excessive sooting occurred at this low mixture ratio (0.55), precluding photographic data.

Judd, D. C.↗

Heterogeneous atmospheric reactions - Sulfuric acid aerosols as tropospheric sinks

The reaction probabilities of various atmospheric species incident on a bulk sulfuric acid surface are measured in order to determine the role of sulfuric acid aerosols as pollutant sinks. Reaction products and unreacted starting materials leaving a Knudsen cell flow reactor after collision at 300 K with a H2SO4 surface or a soot surface were detected by mass spectrometry. Significant collision reaction probabilities are observed on a H2SO4 surface for H2O2, HNO3, HO2NO2, ClONO2, N2O5, H2O and NH3, and on soot for NH3. Estimates of the contribution of heterogeneous reactions to pollutant removal under atmospheric conditions indicate that while aerosol removal in the stratosphere is insignificant (loss rate constants approximately 10 to the -10th/sec), heterogeneous reactions may be the dominant loss process for several tropospheric species (loss rate constant approximately 10 to the -5th/sec, comparable to photolysis rate constants).

Baldwin, A. C.↗

Stratospheric aerosol modification by supersonic transport and space shuttle operations - Climate implications

The potential effects on stratospheric aerosols of supersonic transport emissions of sulfur dioxide gas and submicron soot granules, and space shuttle rocket emissions of aluminum oxide particulates are estimated. An interactive particle-gas model of the stratospheric aerosol layer is used to calculate changes due to exhaust emissions, and an accurate radiation transport model is employed to compute the effect of aerosol changes on the earth's average surface temperature. It is concluded that the release of large numbers of small particles (soot or aluminum oxide) into the stratosphere should not lead to a corresponding significant increase in the concentration of large, optically active aerosols, but that the increase in large particles is severely limited by the total mass of sulfate available to make large particles in situ, and by the rapid loss of small seed particles via coagulation. We find that a fleet of several hundred advanced supersonic aircraft operating daily at 20 km, or the launch of one space shuttle rocket per week, could produce roughly a 20% increase in the large-particle concentration of the stratosphere. We find, in addition, that aerosol increases of this magnitude would reduce the global surface temperature by less than 0.01 K.

Turco, R. P.↗

Synergistic effects in trace gas-aerosol interactions

The reaction of SO2 and NO2 with soot has been studied experimentally by gravimetric determination of chemisorption with subsequent analysis of the chemisorbed species by various techniques. When samples of commercially available carbon black (used as soot surrogate) are exposed to SO2 or NO2 in dry air or N2 as carrier gas, no quantitative chemisorption (less than 5 micrograms per mg of substrate) is observed. However, exposure of the same grade of carbon to a combination of SO2 and NO2 in dry air of N2 results in significant chemisorption (180-200 micrograms/mg), a major fraction of which is analyzed as sulfate.

Schryer, D. R.↗

Analysis of pressure spectra measurements in a ducted combustion system

Combustion noise propagation in an operating ducted liquid fuel combustion system is studied in relation to the development of combustion noise prediction and suppression techniques. The presence of combustor emissions in the duct is proposed as the primary mechanism producing the attenuation and dispersion of combustion noise propagating in an operating liquid fuel combustion system. First, a complex mathematical model for calculating attenuation and dispersion taking into account mass transfer, heat transfer, and viscosity effects due to the presence of liquid fuel droplets or solid soot particles is discussed. Next, a simpler single parameter model for calculating pressure auto-spectra and cross-spectra which takes into account dispersion and attenuation due to heat transfer between solid soot particles and air is developed. Then, auto-spectra and cross-spectra obtained from internal pressure measurements in a combustion system consisting of a J-47 combustor can, a spool piece, and a long duct are presented. Last, analytical results obtained with the single parameter model are compared with the experimental measurements. The single parameter model results are shown to be in excellent agreement with the measurements.

Miles, J. H.↗

Computation of Three-Dimensional Combustor Performance

Existing steady-state 3-D computer program for calculating gasturbine flow fields modified to include computation of soot and nitrogen oxide emission. In addition, radiation calculation corrected for soot particles. These advanced tools offer potential of reducing design and development time required for gas-turbine combustors.

Srivatsa, S.↗

Combustion/particle sizing experiments at the Naval Postgraduate School Combustion Research Laboratory

Particle behavior in combustion processes is an active research area at NPS. Currently, four research efforts are being conducted: (1) There is a long standing need to better understand the soot production and combustion processes in gas turbine combustors, both from a concern for improved engine life and to minimize exhaust particulates. Soot emissions are strongly effected by fuel composition and additives; (2) A more recent need for particle sizing/behavior measurements is in the combustor of a solid fuel ramjet which uses a metallized fuel. High speed motion pictures are being used to study rather large burning particles; (3) In solid propellant rocket motors, metals are used to improve specific impulse and/or to provide damping for combustion pressure oscillations. Particle sizing experiments are being conducted using diode arrays to measure the light intensity as a function of scattering angle; (4) Once a good quality hologram is attained, a need exists for obtaining the particle distributions from hologram in a short period of time. A Quantimet 720 Image Analyzer is being used to reconstruct images.

Powers, John↗

Combustion chamber heat transfer characterization of LOX/hydrocarbon-type propellants

The gas-side heat transfer rates for LOX/propane and LOX/ethanol are experimentally characterized using a 1000 lb thrust water-cooled calorimeter chamber. The effects of injector element type and fuel film cooling are defined as a function of mixture ratio. The interaction of fuel injected through the resonator cavities on heat transfer and wall soot buildup are displayed as a function of time, axial distance, fuel coolant flow rate, and mixture ratio. Comparisons between clean-burning ethanol and sooting propane show a large difference between the two fuels and significantly higher than expected heat flux levels for ethanol in the throat region.

Schoenman, Leonard↗

Global fire at the Cretaceous-Tertiary boundary

Cretaceous-Tertiary boundary clays rich in iridium from five sites in Europe and New Zealand were investigated. The clays are found to be 100-10,000-fold-enriched in elemental carbon (mainly soot), which is isotopically uniform and apparently comes from a single global fire. The soot layer coincides with the iridium layer, suggesting that the fire was triggered by meteorite impact and began before the ejecta had settled.

Wolbach, Wendy S.↗