Results for “Reacting” — Page 58

NASA NTRSDate not supplied

Implementation of active sites to capture pitting of oxidizing carbon materials in DSMC.

In this work we demonstrate a newly developed capability to capture pitting of carbon fibers in DSMC simulations, specifically using the Stochastic PArallel Rarefied-gas Time-accurate Analyzer (SPARTA) code [1]. State-of-the-art reactive surface models in DSMC compute collision dependent carbon consumption rates (usually through desorption of CO) based on a set of surface reactions that has been derived from molecular beam experiments [2]. The reactivity on each carbon surface element is constant in those models, such that the carbon surface recedes uniformly as a result of ablation. However, it is well known that in reality the carbon surface has locally different reaction rates due to the presence of defects at the atomic scale [3]. These defective sites have a much higher reactivity than the average sites (2-3 orders of magnitude) and are first to react during ablation leading to its removal. This causes all the neighboring atoms to be defective and increase their reactivity, thus leading to the localized carbon removal around these ”active” sites (as shown in Fig. 1). In this manner, these highly reactive defective sites serve as nucleation sites for the formation and growth of etch pits with potentially detrimental effects on the structural integrity. Recently a detailed surface chemistry framework was developed in SPARTA, capable of incorporating various reaction mechanisms such as adsorption, desorption, Eley-Rideal (ER) and Langmuir-Hinshelwood (LH) mechanisms [4]. Within this framework, we have implemented the capability of a single surface having multiple site sets with different reactivities. Using this feature, we can simulate the presence of active sites on carbon surfaces, whose reactivity is much greater than an average site as a result of defects. We have implemented the active site fraction as a property of surface elements within SPARTA, which is directly proportional to the local reactivity of each surface element. By introducing an initial distribution of the active site fraction across the carbon surface, and propagating it in a manner that mimics the evolution of real reacting carbon surfaces, we are able to capture the formation and growth of etch pits as a result of surface consumption reactions such as oxidation.

DSMC↗

NASA NTRSDate not supplied

Implementation of Active Sites in DSMC to Capture Pitting of Oxidizing Carbon Materials

In this work we demonstrate a newly developed capability to capture pitting of carbon fibers in DSMC simulations, specifically using the Stochastic PArallel Rarefied-gas Time-accurate Analyzer (SPARTA) code. State-of-the-art reactive surface models in DSMC compute collision dependent carbon consumption rates (usually through desorption of CO) based on a set of surface reactions that has been derived from molecular beam experiments. The reactivity on each carbon surface element is constant in those models, such that the carbon surface recedes uniformly as a result of ablation. However, it is well known that in reality the carbon surface has locally different reaction rates due to the presence of defects at the atomic scale. These defective sites have a much higher reactivity than the average sites (2-3 orders of magnitude) and are first to react during ablation leading to its removal. This causes all the neighboring atoms to be defective and increase their reactivity, thus leading to the localized carbon removal around these ”active” sites. In this manner, these highly reactive defective sites serve as nucleation sites for the formation and growth of etch pits with potentially detrimental effects on the structural integrity. Recently a detailed surface chemistry framework was developed in SPARTA, capable of incorporating various reaction mechanisms such as adsorption, desorption, Eley-Rideal (ER) and Langmuir-Hinshelwood (LH) mechanisms. Within this framework, we have implemented the capability of a single surface having multiple site sets with different reactivities. Using this feature, we can simulate the presence of active sites on carbon surfaces, whose reactivity is much greater than an average site as a result of defects. We have implemented the active site fraction as a property of surface elements within SPARTA, which is directly proportional to the local reactivity of each surface element. By introducing an initial distribution of the active site fraction across the carbon surface, and propagating it in a manner that mimics the evolution of real reacting carbon surfaces, we are able to capture the formation and growth of etch pits as a result of surface consumption reactions such as oxidation.

DSMC↗

NASA NTRSDate not supplied

Simulation of etch pit formation through active sites in carbon fiber micro-structures

Erosion of carbon due to oxidation does not occur uniformly but through localized etch pit formation as a result of active surface sites. In this work we demonstrate a newly developed capability to capture pitting of carbon fiber microstructures such as FiberForm, which is commonly used as the base material for NASA’s spacecraft ablative thermal protection systems (TPS). The simulations are performed at the meso-scale in order to capture the pit formation and growth using direct simulation Monte Carlo (DSMC), specifically using the Stochastic PArallel Rarefied-gas Time-accurate Analyzer (SPARTA) code. Legacy and latest models both assume uniform reactivity of carbon surface sites with oxygen even at the meso-scale level. However, in reality the carbon surface has locally different reaction rates due to the presence of defects at the atomic scale. The defective nature of these sites enhances their reactivity with atmospheric gases compared to the non-defective sites (2-3 orders of magnitude) and are termed as “active sites”. Thus, these sites tend to be the first to react and eventually get removed through the formation of gasses such as CO, CO2, and CN. Their removal results in all the neighboring atoms becoming defective, thus leading to chain reaction of localized carbon removal and formation of etch pits. Capturing the formation of pits during the ablation simulation of carbon micro-structures is critical to predicting their structural failure. Recently a detailed surface chemistry framework was developed in SPARTA, capable of incorporating various reaction mechanisms such as adsorption, desorption, Eley-Rideal (ER) and Langmuir-Hinshelwood (LH) mechanisms. We have implemented the capability of a single surface having multiple site sets with different reactivities within this framework. We have used this feature to model the presence of active sites on carbon surfaces, whose reactivity is orders of magnitude higher than that of the passive sites due to the presence of defects. The active site fraction is a property of surface elements within SPARTA and is directly proportional to the local reactivity of each surface element. By introducing an initial distribution of the active site fraction across the carbon surface and propagating it in a manner that mimics the evolution of real reacting carbon surfaces, we can capture the formation and growth of etch pits as a result of surface consumption reactions such as oxidation.

DSMC↗

NASA NTRSDate not supplied

Development of the Advanced Regolith Ground Operations (ARGO) Test Bed – A Robotic Excavation and Construction Test Facility with Simulated Lunar Environments

NASA’s Artemis Program is working towards developing a sustained presence on the Moon and eventually Mars. To achieve this goal, robotic excavation, site preparation and construction technologies are under development to establish the capability to construct infrastructure such as launch/landing pads and radiation protection shelters. Technologies must be proven in simulated Lunar conditions prior to surface demonstration missions. To that end, the Relevant Additive Construction Technology (REACT) Announcement of Collaboration Opportunities (ACO) project with AI Space Factory and the NASA Kennedy Space Center’s (KSC) Granular Mechanics and Regolith Operations Laboratory (a.k.a. Swamp Works) has developed the Advanced Regolith Ground Operations (ARGO) Test Bed. ARGO includes a ~1.5m x 1.5m x 1.2m (~5x5x4ft) vacuum chamber, cryogenically cooled thermal shroud, 3-axis robotic positioning system, and regolith bin. For the REACT project, a pellet extruder, feed hopper, and heated 600mm x 600mm (23.6x23.6in) build plate have been installed on ARGO to advance the Technology Readiness Level (TRL) of regolith-polymer composite Fused Deposition Modeling (FDM) additive construction systems, processes, and materials. This paper will focus on the design and operational characteristics of the ARGO Test Bed with pellet extruder.

regolith↗

NASA NTRSDate not supplied

Simulation of Etch Pit Formation in DSMC Through Active Sites in Carbon Fiber Micro-Structures

Erosion of carbon due to oxidation does not occur uniformly but through localized etch pit formation because of active surface sites. In this work we demonstrate a newly developed capability to capture pitting of carbon fiber microstructures such as FiberForm, which is commonly used as the base material for NASA’s spacecraft ablative thermal protection systems (TPS). The simulations are performed at the meso-scale in order to capture the pit formation and growth using direct simulation Monte Carlo (DSMC), specifically using the Stochastic PArallel Rarefied-gas Time-accurate Analyzer (SPARTA) code. Legacy and latest models both assume uniform reactivity of carbon surface sites with oxygen even at the meso-scale level. However, in reality the carbon surface has locally different reaction rates due to the presence of defects at the atomic scale. The defective nature of these sites enhances their reactivity with atmospheric gases compared to the non-defective sites (2-3 orders of magnitude) and are termed as “active sites”. Thus, these sites tend to be the first to react and eventually get removed through the formation of gases such as CO, CO2, and CN. Their removal results in all the neighboring atoms becoming defective, thus leading to chain reaction of localized carbon removal and formation of etch pits. Capturing the formation of pits during the ablation simulation of carbon micro-structures is critical to predicting their structural failure. Recently a detailed surface chemistry framework was developed in SPARTA, capable of incorporating various detailed surface reaction mechanisms. We have implemented the capability of a single surface having multiple site sets with different reactivities within this framework. We have used this feature to model the presence of active sites on carbon surfaces, whose reactivity is orders of magnitude higher than that of the passive sites due to the presence of defects. The active site fraction is a property of surface elements within SPARTA and is directly proportional to the local reactivity of each surface element. By introducing an initial distribution of the active site fraction across the carbon surface and propagating it in a manner that mimics the evolution of real reacting carbon surfaces, we can capture the formation and growth of etch pits as a result of surface consumption reactions such as oxidation.

DSMC↗

NASA NTRSDate not supplied

Development of the Advanced Regolith Ground Operations (ARGO) Test Bed: A Robotic Excavation and Construction Test Facility with Simulated Lunar Environments

NASA’s Artemis Program is working towards developing a sustained presence on the Moon and eventually Mars. To achieve this goal, robotic excavation, site preparation and construction technologies are under development to establish the capability to construct infrastructure such as launch/landing pads and radiation protection shelters. Technologies must be proven in simulated Lunar conditions prior to surface demonstration missions. To that end, the Relevant Additive Construction Technology (REACT) Announcement of Collaboration Opportunities (ACO) project with AI Space Factory and the NASA Kennedy Space Center’s (KSC) Granular Mechanics and Regolith Operations Laboratory (a.k.a. Swamp Works) has developed the Advanced Regolith Ground Operations (ARGO) Test Bed. ARGO includes a ~1.5m x 1.5m x 1.2m (~5x5x4ft) vacuum chamber, cryogenically cooled thermal shroud, 3-axis robotic positioning system, and regolith bin. For the REACT project, a pellet extruder, feed hopper, and heated 600mm x 600mm (23.6x23.6in) build plate have been installed on ARGO to advance the Technology Readiness Level (TRL) of regolith-polymer composite Fused Deposition Modeling (FDM) additive construction systems, processes, and materials. This paper will focus on the design and operational characteristics of the ARGO Test Bed with pellet extruder.

regolith↗

NASA NTRSDate not supplied

Advancements in Burst-Mode Filtered Rayleigh Scattering for High-Speed Gas-Phase Multi-Parameter Measurements

Filtered Rayleigh scattering (FRS) can be used for velocity, density, temperature, and/or pressure measurements over a wide range of non-reacting flow conditions as well as more limited reacting flow conditions. However, the application of FRS to gas-phase measurements in large-scale test facilities can be limited due to low signal levels, strong background interferences, or the requirement for multiple cameras and/or molecular filters to spectrally resolve the signal. This work focuses on the spectral characteristics and wavelength-agility of burst-mode lasers for use in FRS systems. These advancements could improve measurement capability and data quality in applications with high levels of stray background scattering as well as where increased temporal resolution is desirable, such as high-speed flows.

filtered Rayleigh scattering↗

NASA NTRSDate not supplied

Acid Alteration of Clay Minerals With Implication for Mars’ Surface Processes

The co-occurrence of phyllosilicates (clays) and sulfate stratigraphies at many locations on Mars are associated with a sharp change in surface conditions from neutral/alkaline pH during the Noachian (4.1-3.7 Ga) which favored the formation of clays to acidic conditions during the Hesperian (3.7-2.9 Ga) which favored the formation of sulfates. Yet, if these two contrasting geosystems were temporarily sequential, it is unknown how the Hesperian acidic conditions altered the previously formed clay units. We performed laboratory batch experiments to fingerprint the diagnostic features produced during interactions of Mars-analog clays and acidic solutions. Two clays, and silicon (IV) oxide, were reacted with solution of either sulfuric acid or filtered natural acid rock drainage (ARD) in plastic bottles. The solutions were adjusted at four pH values (1, 3, 5, and 7) and reacted at 4, 30, and 80°C for 3, 7, and 14 days. At the end of the experiments, the filtered supernatants were analyzed by ICP-MS while the solids were characterized by X-Ray Diffraction; Energy-Dispersive X-Ray Fluorescence analyses; Raman and Short-Wave Infrared spectroscopies and Scanning Electron Microscopy. Results show that the solution chemistry played a key role in the evolution of the clay-solution systems. In H2SO4 systems, the solution pH steadily increased due to partial clay dissolution with no secondary phase formation detected. Contrary, in the ARD systems, the pH decreased due to the ample presence of Fe which controlled both the reactivity of clays by the growth of protecting surface coatings and the solution pH by the precipitation of Fe nanophases; secondary phase detected included goethite, jarosite, gypsum, and siderite. These results indicate that, on Mars, the chemical interaction between clays and acidic solutions was complex and dependent on the solution chemistry. Acidic, sulfate-rich solutions have a high dissolution capacity and could have induced widespread clay disintegration. Notably, if Fe-rich ARD was involved, the clays on Mars could have remained stable during acidic Hesperian period due to formation of protective coatings. Comparison of our results with martian observations will be performed to determine how acidic conditions could potentially affect clays in sedimentary settings, including the Gale crater.

L. Lefticariu↗

NASA NTRSDate not supplied

DSMC Simulation of Etch Pit Formation Through Active Sites in Carbon Fiber Micro-Structures

Erosion of carbon due to oxidation does not occur uniformly but through localized etch pit formation because of active surface sites. In this work we demonstrate a newly developed capability to capture pitting of carbon fiber microstructures such as FiberForm, which is commonly used as the base material for NASA’s spacecraft ablative thermal protection systems (TPS). The simulations are performed at the meso-scale in order to capture the pit formation and growth using direct simulation Monte Carlo (DSMC), specifically using the Stochastic PArallel Rarefied-gas Time-accurate Analyzer (SPARTA) code. Legacy and latest models both assume uniform reactivity of carbon surface sites with oxygen even at the meso-scale level. However, in reality the carbon surface has locally different reaction rates due to the presence of defects at the atomic scale. The defective nature of these sites enhances their reactivity with atmospheric gases compared to the non-defective sites (2-3 orders of magnitude) and are termed as “active sites”. Thus, these sites tend to be the first to react and eventually get removed through the formation of gases such as CO, CO2, and CN. Their removal results in all the neighboring atoms becoming defective, thus leading to chain reaction of localized carbon removal and formation of etch pits. Capturing the formation of pits during the ablation simulation of carbon micro-structures is critical to predicting their structural failure. Recently a detailed surface chemistry framework was developed in SPARTA, capable of incorporating various detailed surface reaction mechanisms. We have implemented the capability of a single surface having multiple site sets with different reactivities within this framework. We have used this feature to model the presence of active sites on carbon surfaces, whose reactivity is orders of magnitude higher than that of the passive sites due to the presence of defects. The active site fraction is a property of surface elements within SPARTA and is directly proportional to the local reactivity of each surface element. By introducing an initial distribution of the active site fraction across the carbon surface and propagating it in a manner that mimics the evolution of real reacting carbon surfaces, we can capture the formation and growth of etch pits as a result of surface consumption reactions such as oxidation.

DSMC↗

NASA NTRS2024

Basalt Alteration in a CO 2 -SO 2 Atmosphere: Implications for Surface Processes on Venus

Venus’ surface and interior dynamics remain largely unconstrained, due in great part to the major obstacles to exploration imposed by its 470°C, 90 bar surface conditions and its thick, opaque atmosphere. Orbiter-based thermal emission data provide opportunities to characterize the surface composition of Venus. However, interpretations of such spectra depend on understanding interactions between the planet’s surface basaltic rocks and its caustic, sulfur dioxide (SO 2 )-bearing carbon dioxide (CO 2 ) atmosphere. Several studies, using remote sensing, thermodynamic modeling, and laboratory experiments, have placed constraints on basaltic alteration mineralogies and rates. Yet constraint with respect to SO 2 -mediated reactions with basalts of contrasting compositions remains incomplete. Here, we present new data from a series of gas-solid reaction experiments, in which samples of two basalt compositions were reacted in an SO 2 -bearing CO 2 atmosphere, at relevant Venus temperatures, pressure, and oxygen fugacity. We subjected reacted specimens to scanning electron microscopy (SEM) and scanning transmission electron microscopy (STEM) analyses using sample cross-sections produced with focused ion beam (FIB) milling. Surface alteration products were characterized, and their abundances estimated; subsurface cation concentrations were mapped to show depth of alteration. We demonstrate that the initial rate of reaction in our experiments is very rapid. Alkaline basalt samples are coated by (meta)thenardite (Na 2 SO 4 ) and amorphous calcium carbonate (CaCO 3 ) alteration products, and tholeiitic basalt samples are primarily covered by anhydrite (CaSO 4 ), Fe-oxide (Fe x O y : likely magnetite, Fe 3 O 4 ), and other minor phases.

Venus↗

NASA NTRSDate not supplied

Fiber-Based Multi-Resolution Imaging and Multidimensional X-ray Diagnostics for Ejecta Dynamics in Plume Surface Interactions

The interaction of a rocket exhaust plume with a particulate-laden surface creates a complex, multiphase flow field that can destabilize the vehicle and damage nearby equipment. This study investigates two methods for capturing the particulate dynamics of plume-surface interaction (PSI): optical fiber-based multi-resolution Mie scattering and multi-dimensional X-ray radiography. Mie scattering was used to track PSI-interacted particles, trace their paths, and measure velocities. While effective for the jet periphery and early PSI stages, the technique becomes limited as the scattering cross-section increases over time due to particle displacement from the soil bed, causing the core to become optically dense and appear as a luminous, opaque region. To address this, X-ray radiography was explored as a complementary method for visualizing the optically dense core. PSI experiments were conducted with both reacting and non-reacting jets to evaluate these approaches across a range of optical and flow parameters. The results demonstrated the capability of the fiber-based multi-resolution imaging system to capture simultaneous fields of view at varying magnifications (1x, 2x, 4x), and the ability of X-ray imaging to penetrate the optically dense plume, revealing flow structures that would otherwise be obscured in scattering-based methods. Data were collected for various PSI parameters, including three different heights above the surface, to analyze the ejecta properties and the plume’s temporal evolution. These results provide the first imaging strategy capable of resolving flow structures over a wide spatial dynamic range while also offering the first visualization of the optically dense core.

Ejecta↗

NASA NTRSDate not supplied

Mitigating Grazing Flow Impedance Eduction Errors in Additively Manufactured Porous Liners

Additively manufactured porous metamaterials, including triply periodic minimal surface (TPMS) cores, are promising candidates for aeroengine liners but often behave as extended-reacting treatments under grazing flow. Standard impedance eduction procedures assume locally-reacting behavior and can yield physically inconsistent results for such materials. This study evaluates internal partitions (thin solid walls inserted at regular intervals along the liner’s streamwise extent) as a means of suppressing internal streamwise propagation to improve eduction consistency. Six TPMS configurations were tested in the NASA Langley Grazing Flow Impedance Tube (GFIT) at partition spacings of 4′′, 2′′, and 1′′, as well as unpartitioned, and at Mach numbers up to 0.3. For most geometries, 2′′ partition spacing eliminated impedance discontinuities and substantially improved Prony correlation, though effectiveness varied with core topology. Partitions also altered the acoustic response of the liners: resistance increased, resonance frequencies shifted downward, and peak attenuation decreased while bandwidth broadened in some cases. Because partitions modify the liner itself, the educed impedance characterizes the partitioned system rather than the original unpartitioned core. These results establish partitioning as a practical pathway toward liners that are more compatible with standard eduction methods, while demonstrating that the intervention is itself an acoustic design change.

liners↗

DOE OSTI2020

Amidoxime-functionalized materials and their use in extracting metal ions from liquid solutions

A method of producing a functionalized material that extracts metal ions from solution, the method comprising: (i) providing a precursor material having nitrile groups appended to its surface; and (ii) reacting said nitrile groups with hydroxylamine or a derivative thereof in the presence of a polar aprotic solvent at a temperature of 60-80° C. for at least 1 hour, to convert at least a portion of said nitrile groups to amidoxime and imide dioxime groups, followed by reaction with a base capable of hydrolyzing any remaining nitrile groups to carboxylic acid groups; wherein said functionalized material has a higher uranium absorption capacity than a functionalized material produced under same conditions except that the nitrile groups are reacted with hydroxylamine in only a protic solvent. The invention is also directed to functionalized materials produced by the above-described method, and methods for using the functionalized material for extracting metal ions from metal-containing solutions.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Method of selectively oxidizing lignin

A method of selectively reacting lignin or a lignin-derived reactant to yield an aromatic product. The method includes the step of reacting lignin or a lignin-derived reactant with a molybdenum-containing catalyst, in a solvent, and optionally in the presence of an oxidant, for a time and a temperature wherein at least a portion of the lignin or lignin-derived reactant is selectively converted into an aromatic product, preferably coniferaldehyde and/or sinapaldehyde.

09 BIOMASS FUELS↗

DOE OSTI2021

Noble metal catalysts and processes for reforming of methane and other hydrocarbons

Processes for converting methane and/or other hydrocarbons to synthesis gas (i.e., a gaseous mixture comprising H 2 and CO) are disclosed, in which at least a portion of the hydrocarbon(s) is reacted with CO 2 . At least a second portion of the methane may be reacted with H 2 O (steam), thereby improving overall thermodynamics of the process, in terms of reducing endothermicity (ΔH) and the required energy input, compared to “pure” dry reforming in which no H2O is present. Catalysts for such processes advantageously possess high activity and thereby can achieve significant levels of methane conversion at temperatures below those used conventionally under comparable conditions. These catalysts also exhibit high sulfur tolerance, in addition to reduced rates of carbon (coke) formation, even in the processing (reforming) of heavier (e.g., naphtha boiling-range or jet fuel boiling-range) hydrocarbons. The robustness of the catalyst translates to high operating stability. A representative catalyst comprises 1 wt-% Pt and 1 wt-% Rh as noble metals, on a cerium oxide support.

Marker, Terry L.↗

DOE OSTI2021

Synthesis of metal complexes and uses thereof

The present disclosure provides novel methods of making aluminum complexes with utility for promoting epoxide carbonylation reactions. Methods include reacting neutral metal carbonyl compounds with alkylaluminum complexes. For example, a compound of formula I: is reacted with a neutral metal carbonyl compound (such as Q′dMe(CO)w′) to produce an aluminum-based carbonylation catalyst:

Lee, Han↗

DOE OSTI2021

Methods and apparatus for additively manufacturing structures using in situ formed additive manufacturing materials

A method of additively manufacturing a structure comprises nuclear reactor comprises disposing a feed material on a surface of a substrate in a reaction vessel, disposing at least one material formulated and configured to react with the feed material in the reaction vessel, and exposing the feed material and the at least one material to energy from an energy source to react the feed material and the at least one material to form an additive manufacturing material and reaction by-products. The additive manufacturing material is separated from the reaction by-products and exposed to energy from the energy source to form inter-granular bonds between particles of the additive manufacturing material and form a layer of a structure comprising the additive manufacturing material. Related apparatuses and methods are disclosed.

van Rooyen, Isabella J.↗

DOE OSTI2021

Systems and methods for producing nitriles

An aspect of the present disclosure is a method that includes a first reacting a molecule from at least one of a carboxylic acid, an ester of a carboxylic acid, and/or an anhydride with ammonia to form a nitrile, where the first reacting is catalyzed using an acid catalyst. In some embodiments of the present disclosure, the molecule may include at least one of acetic acid, lactic acid, and/or 3-hydroxyproprionic acid (3-HPA). In some embodiments of the present disclosure, the molecule may include at least one of methyl acetate, ethyl lactate, and/or ethyl 3-hydroxypropanoate (ethyl 3-HP). In some embodiments of the present disclosure, the anhydride may be acetic anhydride.

Karp, Eric M.↗