Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RETENTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Enhanced Electrochemical Performance of Disordered Rocksalt Cathodes in a Localized High‐Concentration Electrolyte

Abstract Lithium (Li)‐rich transition metal oxide cathodes with a cation disordered rock salt structure (DRX) are increasingly gaining popularity for advanced Li batteries as they offer high capacity and cost benefits over the commonly used layered Li transition metal oxide cathodes. However, the performance of DRX cathodes and their applications are limited by severe side reactions between the cathode and the state‐of‐the‐art carbonate‐based electrolytes at high voltage of 4.8 V, transition metal dissolution, and structural instability of the cathode particles. In this work, an advanced localized high‐concentration electrolyte (LHCE) is developed to form a stable cathode‐electrolyte interphase and mitigate structural instability of the Li 1.13 Mn 0.66 Ti 0.21 O 2 (LMTO) DRX during electrochemical cycling. Li||LMTO half cells with the LHCE demonstrate increased capacity, cycling stability, and superior rate capability compared with cells containing a conventional carbonate electrolyte. For instance, the Li||LMTO cells cycled in LHCE show a higher initial capacity of 205.2 mAh g −1 and a better capacity retention of 72.5% after 200 cycles at a current density of 20 mA g −1 than those with the conventional electrolyte (initial capacity of 187.7 mAh g −1 and capacity retention of 19.9%). This work paves the way to the development of practical DRX cathode‐based high‐energy Li batteries.

25 ENERGY STORAGE↗

Battery Electrolyte Design for Electric Vertical Takeoff and Landing (eVTOL) Platforms

Here, the development of robust and high-performance battery systems is crucial for the advancement of Electric Vertical Takeoff and Landing (eVTOL) vehicles for urban air mobility. This study evaluates the performance of different lithium-ion battery chemistries under Electric Vertical Takeoff and Landing (eVTOL) load profiles. The actual flight data coupled with physical models is used to create discharge profiles for testing on developed lithium-ion cells for eVTOLs. The performance of a standard liquid electrolyte (1.2 M LiPF 6 in EC:EMC), labeled Gen-2, is benchmarked and compared with a fast-charging electrolyte (1.2 M LiFSI in EC:EMC), labeled XFC. Cell analysis involves the use of various techniques, such as impedance spectroscopy, polarization curves, and capacity retention measurements. Capacity retention is stable for both systems over 500 cycles, but unique discharge capacity trends are observed for different mission segments. During the initial takeoff hover stages, Gen-2 electrolytes experience substantial voltage fade, while XFC electrolytes maintain consistent behavior. In general, the Gen-2 electrolyte demonstrated lower discharge overpotentials and higher decay during cycling compared to the XFC electrolyte. This work highlights the complexity of eVTOL battery behavior and provides insights into battery system design, contributing to the advancement of battery energy storage solutions for urban air mobility.

25 ENERGY STORAGE↗

A Comprehensive Experimental Study on Microstructure‐Graded Graphite Anodes for Enhancing Fast‐Charging Capability of Lithium‐Ion Batteries

Lithium‐ion batteries with high gravimetric capacity density and improved cycle life performance under fast‐charging conditions are crucial for widespread electric vehicle (EV) adoption. This study investigates how designing graphite anode microstructure, specifically porosity, and particle‐size gradients, improves lithium‐ion (Li + ) transport during fast‐charging conditions. Three‐layered graphite anodes with varying porosity (24%, 36%, 46%) and particle size gradients (3, 5, 10 μm) were compared to a conventional single‐layered electrode in half‐cell configurations. At room temperature and high discharge rate (2C), both gradient structures showed significantly enhanced capacity retention (80% and 67% vs. 50%) compared to the conventional electrode, highlighting the effectiveness of microstructure engineering for fast charging. The study also investigated the temperature's impact on cycle life. After 200 cycles at 2°C and 45°C, all gradient structures demonstrated superior capacity retention (≈80%) compared to the conventional electrode (35%), suggesting the gradients mitigate degradation rate at high temperatures. Electrochemical impedance spectroscopy confirmed superior Li+ diffusion and lower resistivity in gradient electrodes. Simulations explored the influence of gradient profiles on reaction kinetics across the electrode thickness. Overall, this research demonstrates that the fast‐charging capability of graphite electrodes can be greatly enhanced by engineering the electrode microstructure, thereby making EV technology more accessible and appealing.

Ahmadi, Soma↗

Halophytes and heavy metals: A multi‐omics approach to understand the role of gene and genome duplication in the abiotic stress tolerance of Cakile maritima

Abstract Premise The origin of diversity is a fundamental biological question. Gene duplications are one mechanism that provides raw material for the emergence of novel traits, but evolutionary outcomes depend on which genes are retained and how they become functionalized. Yet, following different duplication types (polyploidy and tandem duplication), the events driving gene retention and functionalization remain poorly understood. Here we usedCakile maritima, a species that is tolerant to salt and heavy metals and shares an ancient whole‐genome triplication with closely related salt‐sensitive mustard crops (Brassica), as a model to explore the evolution of abiotic stress tolerance following polyploidy. Methods Using a combination of ionomics, free amino acid profiling, and comparative genomics, we characterize aspects of salt stress response inC. maritimaand identify retained duplicate genes that have likely enabled adaptation to salt and mild levels of cadmium. Results Cakile maritimais tolerant to both cadmium and salt treatments through uptake of cadmium in the roots. Proline constitutes greater than 30% of the free amino acid pool inC. maritimaand likely contributes to abiotic stress tolerance. We find duplicated gene families are enriched in metabolic and transport processes and identify key transport genes that may be involved inC. maritimaabiotic stress tolerance. Conclusions These findings identify pathways and genes that could be used to enhance plant resilience and provide a putative understanding of the roles of duplication types and retention on the evolution of abiotic stress response.

Plant Sciences↗

Vacancy‐Enabled O3 Phase Stabilization for Manganese‐Rich Layered Sodium Cathodes

Abstract Manganese‐rich layered oxide materials hold great potential as low‐cost and high‐capacity cathodes for Na‐ion batteries. However, they usually form a P2 phase and suffer from fast capacity fade. In this work, an O3 phase sodium cathode has been developed out of a Li and Mn‐rich layered material by leveraging the creation of transition metal (TM) and oxygen vacancies and the electrochemical exchange of Na and Li. The Mn‐rich layered cathode material remains primarily O3 phase during sodiation/desodiation and can have a full sodiation capacity of ca. 220 mAh g −1 . It delivers ca. 160 mAh g −1 specific capacity between 2–3.8 V with >86 % retention over 250 cycles. The TM and oxygen vacancies pre‐formed in the sodiated material enables a reversible migration of TMs from the TM layer to the tetrahedral sites in the Na layer upon de‐sodiation and sodiation. The migration creates metastable states, leading to increased kinetic barrier that prohibits a complete O3‐P3 phase transition.

Xiao, Biwei↗

Making Plasticized Polymer Electrolytes Stable Against Sodium Metal for High‐Energy Solid‐State Sodium Batteries

Abstract Solid polymer electrolytes based on plastic crystals are promising for solid‐state sodium metal (Na 0 ) batteries, yet their practicality has been hindered by the notorious Na 0 ‐electrolyte interface instability issue, the underlying cause of which remains poorly understood. Here, by leveraging a model plasticized polymer electrolyte based on conventional succinonitrile plastic crystals, we uncover its failure origin in Na 0 batteries is associated with the formation of a thick and non‐uniform solid electrolyte interphase (SEI) and whiskery Na 0 nucleation/growth. Furthermore, we design a new additive‐embedded plasticized polymer electrolyte to manipulate the Na 0 deposition and SEI formulation. For the first time, we demonstrate that introducing fluoroethylene carbonate (FEC) additive into the succinonitrile‐plasticized polymer electrolyte can effectively protect Na 0 against interfacial corrosion by facilitating the growth of dome‐like Na 0 with thin, amorphous, and fluorine‐rich SEIs, thus enabling significantly improved performances of Na//Na symmetric cells (1,800 h at 0.5 mA cm −2 ) and Na//Na 3 V 2 (PO 4 ) 3 full cells (93.0 % capacity retention after 1,200 cycles at 1 C rate in coin cells and 93.1 % capacity retention after 250 cycles at C/3 in pouch cells at room temperature). Our work provides valuable insights into the interfacial failure of plasticized polymer electrolytes and offers a promising solution to resolving the interfacial instability issue.

Zou, Peichao↗

Making Plasticized Polymer Electrolytes Stable Against Sodium Metal for High‐Energy Solid‐State Sodium Batteries

Solid polymer electrolytes based on plastic crystals are promising for solid-state sodium metal (Na 0 ) batteries, yet their practicality has been hindered by the notorious Na 0 -electrolyte interface instability issue, the underlying cause of which remains poorly understood. Here, in this study, by leveraging a model plasticized polymer electrolyte based on conventional succinonitrile plastic crystals, we uncover its failure origin in Na 0 batteries is associated with the formation of a thick and non-uniform solid electrolyte interphase (SEI) and whiskery Na 0 nucleation/growth. Furthermore, we design a new additive-embedded plasticized polymer electrolyte to manipulate the Na 0 deposition and SEI formulation. For the first time, we demonstrate that introducing fluoroethylene carbonate (FEC) additive into the succinonitrile-plasticized polymer electrolyte can effectively protect Na 0 against interfacial corrosion by facilitating the growth of dome-like Na 0 with thin, amorphous, and fluorine-rich SEIs, thus enabling significantly improved performances of Na//Na symmetric cells (1,800 h at 0.5 mA cm −2 ) and Na//Na 3 V 2 (PO 4 ) 3 full cells (93.0 % capacity retention after 1,200 cycles at 1 C rate in coin cells and 93.1 % capacity retention after 250 cycles at C/3 in pouch cells at room temperature). Our work provides valuable insights into the interfacial failure of plasticized polymer electrolytes and offers a promising solution to resolving the interfacial instability issue.

25 ENERGY STORAGE↗

Halting Oxygen Evolution to Achieve Long Cycle Life in Sodium Layered Cathodes

Oxygen redox chemistries at high voltage have materialized as a revolutionary paradigm for cathodes with high-energy density; however, they are plagued by the challenges of labile oxygen loss and rapid degradations upon cycling, even after concerted endeavors from the research community. Here we propose a multi-concentration stratagem propelled by entropy reinforcement to enhance the electronic structure disorder (ESD) at high desodiation states for impeding undesired oxygen mobility and ensuring controlled oxygen activity, elucidated by density functional theory calculations. The increased disorder strengthens the reversible electrochemistry of lattice oxygen redox, leading to effectively suppressed P−O structural evolution and highly stable localized TMO 6 octahedral environments, as demonstrated by soft/hard X-ray absorption spectroscopy. Furthermore, through a comparative analysis of sodium-layered cathodes with different configuration entropy, we reveal that a high-entropy state induced by cationic disordering has the capacity to perturb cationic redox boundaries, significantly restraining the formation of detrimental O′3 phases. As a consequence, the high-voltage cycling stability has been greatly upgraded, up to 4.4 V versus Na + /Na, with an impressive 90.1 % capacity retention at 1 C over 100 cycles and 76.1 % capacity retention at 2 C over 300 cycles. In conclusion, the resilient oxygen redox, enabled through the control of ESD, broadens the horizons for entropy engineering and lays the foundation for advancements in high-energy, long-cycling, and safe batteries.

25 ENERGY STORAGE↗

Understanding the performance of membrane for direct air capture of CO 2

Abstract Direct air capture (DAC) of CO 2 is becoming increasingly important for reducing greenhouse gas concentrations in the atmosphere. However, the cost and energy requirements associated with DAC make it less economically feasible than carbon capture from flue gases. While various methods like solid sorbents and gas–liquid absorption have been explored for DAC, membrane processes have only recently been investigated. The objective of this study is to examine the separation performance of a membrane unit for capturing CO 2 from ambient air. The performance of a membrane depends on several factors, including the composition of the feed gas, pressure ratio, material selectivity, and membrane area. The single‐stage separation process with the co‐current flow and constant permeability flux model is evaluated using a commercial module integrated with a process simulator to separate a binary mixture of carbon dioxide and nitrogen to assess the sensitivity of selectivity on purity and recovery of CO 2 in permeate, and power requirement. Additionally, three levels of CO 2 reduction from the feed stream to the retentate stream (25%, 50%, and 75%) are studied. A trade‐off between purity and recovery factor is observed, and achieving high purity in permeate requires high concentration in the retentate.

Panja, Palash↗

3D Carbon Coating Enabled High‐capacity and Stable Micro‐sized Silicon Suboxide‐graphite Blended Anodes for Practical Lithium‐ion Batteries

Abstract Silicon oxide (SiO x ) is a promising anode candidate of lithium‐ion batteries (LIBs) owing to its extremely high specific capacity. However, the low initial Coulombic efficiency (ICE) and rapid capacity degradation of SiO x , triggered by the enormous volume variation upon repeated (de)lithiation, gravely hinder its practical use. Herein, two mass‐produced micro‐sized SiO x @C composites with obviously different morphologies for commercial LIBs are reported. Particularly, the SiO x ‐graphite blended anode (SiO x @3D‐G‐Gr) based on SiO x wrapped by three‐dimensional (3D) carbon layers (SiO x @3D‐G) exhibits a capacity of 519 mAh g −1 , an ICE of 90.0 % and a capacity retention of 83.4 % at 0.2 C over 100 cycles. which is far exceeding its counterpart SiO x @C‐H‐Gr (65.7 %). The obtained impressive properties of SiO x @3D‐G originate from the critical contribution of 3D carbon layers, which serves as the effective stress buffer and protective layer as well as the strong networks for electron/Li + transport. Accordingly, the full‐cell based on SiO x @3D‐G‐Gr anode and commercial LiCoO 2 cathode delivers a capacity of 803 mAh and an excellent capacity retention of 95.6 % (616 mAh, 96.6 % for graphite, respectively) at 1 C over 100 cycles with a stabilized CE of nearly 100 %. The micro‐sized SiO x @3D‐G showing a promising prospect in the commercial‐grade anodes in LIBs.

Electrochemistry↗

Biopolymer‐assisted Synthesis of P‐doped TiO 2 Nanoparticles for High‐performance Lithium‐ion Batteries: A Comprehensive Study

Abstract TiO 2 material has gained significant attention for large‐scale energy storage due to its abundant, low‐cost, and environmentally friendly properties, as well as the availability of various nanostructures. Phosphorus doping has been established as an effective technique for improving electronic conductivity and managing the slow ionic diffusion kinetics of TiO 2 . In this study, non‐doped and phosphorus doped TiO 2 materials were synthesized using sodium alginate biopolymer as chelating agent. The prepared materials were evaluated as anode materials for lithium‐ion batteries (LIBs). The electrodes exhibit remarkable electrochemical performance, including a high reversible capacity of 235 mAh g −1 at 0.1 C and excellent first coulombic efficiency of 99 %. An integrated approach, combining operando XRD and ex‐situ XAS, comprehensively investigates the relationship between phosphorus doping, material structure, and electrochemical performance, reinforced by analytical tools and first principles calculations. Furthermore, a full cell was designed using 2 %P‐doped TiO 2 anode and LiFePO 4 cathode. The output voltage was about 1.6 V with high initial specific capacity of 148 mAh g −1 , high rate‐capability of 120 mAh g −1 at 1 C, and high‐capacity retention of 96 % after 1000 cycles at 1 C.

El Halya, Nabil↗

Exposure History and its Effect Towards Stabilizing Li Exchange Across Disordered Rock Salt Interfaces

Abstract The application of lithium rich disordered rock salts (DRX) as cathode materials has greatly expanded the materials space for high energy density cathodes. These materials are able to consistently achieve capacities higher than via a complex percolation based intercalation mechanism. Most current DRX materials face significant capacity fade when cycled over an extended period. One of the factors responsible for this could be deleterious side effect of interface reactions between the electrode and electrolyte at high voltage. We aim to focus on one aspect of this interaction, i.e the effect of exposure to electrolyte on the surface and its effect on the electrochemical properties of (LMNOF) powder. LMNOF was systematically treated in an electrolyte solution for varying periods of time at an elevated temperature. Treated samples exhibit surface layer modification (removal of F rich surface layer), leading to a 10 % improvement in the capacity retention behavior of LMNOF. Surface and bulk based measurements indicate an increase in disorder and gradual removal of F and Li. All of these processes mimic an aging process similar to cycling. This a priori formed interface allows for increased stability with respect to retention of capacity and oxygen loss.

Satish, Rohit↗

Simultaneous Stabilization of LiNi 0.76 Mn 0.14 Co 0.10 O 2 Cathode and Lithium Metal Anode by Lithium Bis(oxalato)borate as Additive

Abstract The long‐term cycling performance, rate capability, and voltage stability of lithium (Li) metal batteries with LiNi 0.76 Mn 0.14 Co 0.10 O 2 (NMC76) cathodes is greatly enhanced by lithium bis(oxalato)borate (LiBOB) additive in the LiPF 6 ‐based electrolyte. With 2 % LiBOB in the electrolyte, a Li∥NMC76 cell is able to achieve a high capacity retention of 96.8 % after 200 cycles at C/3 rate (1 C=200 mA g −1 ), which is the best result reported for a Ni‐rich NMC cathode coupled with Li metal anode. The significantly enhanced electrochemical performance can be ascribed to the stabilization of both the NMC76 cathode/electrolyte and Li‐metal‐anode/electrolyte interfaces. The LiBOB‐containing electrolyte not only facilitates the formation of a more compact solid–electrolyte interphase on the Li metal surface, it also forms a enhanced cathode electrolyte interface layer, which efficiently prevents the corrosion of the cathode interface and mitigates the formation of the disordered rock‐salt phase after cycling. The fundamental findings of this work highlight the importance of recognizing the dual effects of electrolyte additives in simultaneously stabilizing both cathode and anode interfaces, so as to enhance the long‐term cycle life of high‐energy‐density battery systems.

Zhao, Wengao↗

Oriented, One‐Dimensional Tin Dioxide–Titanium Dioxide Composites as Anode Materials for Lithium‐Ion Batteries

Abstract Highly oriented columnar nanostructures of tin dioxide (SnO 2 ) and a composite tin dioxide material with a thin titanium dioxide coating (SnO 2 –TiO 2 ) are fabricated using aerosol chemical vapor deposition (ACVD) and are utilized as high‐capacity anode materials in lithium‐ion batteries. The SnO 2 nanostructures exhibit a specific capacity of 445 mAh g −1 after 100 cycles at a rate of 1 C, but experience substantial capacity fade at a charge rate of 2 C, and a capacity of 251 mAh g −1 after 100 cycles. To enhance the capacity retention a coating of TiO 2 is applied to the electrodes. Comparatively, the SnO 2 –TiO 2 electrode exhibits a capacity of 497 mAh g −1 after 100 cycles at a charge rate of 2 C. Diffusion measurements indicate that no inhibition of lithium diffusion occurs due to a thin TiO 2 coating. The superior capacity retention of the composite electrode may be attributed to the protection of SnO 2 from irreversible reactions using a TiO 2 coating.

Kacica, Clayton T.↗

Fluorinated Rocksalt‐Polyanion Cathode for Lithium‐Ion Batteries

Integrated rocksalt‐polyanion cathodes (DRXPS) are promising candidates for next‐generation lithium‐ion battery cathode materials that combine high energy density, stable cycling performance, and reduced reliance on Co and Ni. In this work, we investigated Li 3 Mn 1.6 P 0.4 O 5.4 F 0.6 , a new DRXPS cathode with fluoride incorporation. A pure spinel phase was formed and a discharge capacity retention of 84% was achieved after 200 cycles between 1.5 and 4.8 V versus Li/Li + . In comparison, the similarly synthesized Li 3 Mn 1.6 Nb 0.4 O 5.4 F 0.6 , in which all P 5+ was substituted by Nb 5+ while maintaining the same stoichiometry for all other elements, crystallized in a disordered rocksalt structure, and exhibited inferior capacity retention and rate capability than the P 5+ counterpart. Our findings expand the compositional space of DRXPS to include F − , justify the viability of integrating polyanion groups in rocksalt‐type cathodes, and highlight the superiority of P 5+ as a cation charge compensator compared to the commonly used Nb 5+ . This work thereby advances the design of robust, high‐performance cathode materials for sustainable batteries.

36 MATERIALS SCIENCE↗

Degradation in Photovoltaic Encapsulant Transmittance: Results of the Second PVQAT TG5 Artificial Weathering Study

The optical degradation of encapsulants from ultraviolet (UV) radiation has historically resulted in a significant loss in performance throughout the life of a photovoltaic (PV) module. International Electrotechnical Commission (IEC) test methods have recently been developed to screen for PV encapsulants prone to loss in optical performance. The present study was performed to benchmark polymeric packaging materials relative to IEC 62788-1-4 (covering the measurement of optical transmittance) and IEC 62788-1-7 (on the durability of transmittance), provide feedback toward improvement of the methods, and develop insight regarding optical degradation. Contemporary materials were examined, including poly(ethylene-co-vinyl acetate) (EVA), thermoplastic polyolefin (TPO), polyolefin elastomer (POE), and polyvinyl butyral (PVB) encapsulants; a poly(ethene-co-tetrafluoroethene)/poly(ethylene terephthalate) (ETFE/PET) transparent backsheet; and a polystyrene (PS) working reference material. The use of silica-, specialty-, and rolled-glass was also compared in laminated coupons. Specimen size was separately examined from 2.5 to 12.5 cm. Weathering was performed with a xenon source, using IEC TS 62788-7-2 methods A2, A3, A4, and A5 (chamber temperature of 55 degrees C, 65 degrees C, 75 degrees C, or 85 degrees C), respectively. Characterizations were made using a UV-visible-near-infrared (UV-VIS-NIR) spectrophotometer (transmittance and reflectance, with and without an integrating sphere), a UV-VIS fluorescence spectrophotometer, a camera, and an optical microscope. Performance was analyzed, including solar weighted transmittance, yellowness index, UV cut-off wavelength, and haze (scattering). Separate Arrhenius analyses were performed to assess retention of transmittance and changes in yellowness index. The activation energy for both characteristics was found to range from 15-80 kJ mol-1, with an average of 48 kJ mol-1, similar to the average of 45 kJ mol-1 identified in the previous international PV Quality Assurance Task Force (PVQAT) Task Group 5 (TG5) study of more traditional encapsulants. The separate degradation modes of discoloration and scattering were distinguished in the encapsulants using a comprehensive spectral characterization. Based on these results, the IEC 62788-1-7 pass/fail criteria of 5% change in transmittance was confirmed to identify a known bad encapsulant.

durability↗

Ionic Liquid–Directed Nanoporous TiNb 2 O 7 Anodes with Superior Performance for Fast–Rechargeable Lithium–Ion Batteries

Nanoporous TiNb 2 O 7 (NPTNO) material is synthesized by a sol–gel method with an ionic liquid (IL) as the nanoporous structure directing template. NPTNO exhibits a high reversible capacity of 210 mAh g –1 even at the charging rate of 50 C and an excellent cyclability of half-cell capacity retention of 74% for 1000 cycles at 5 C and LiNi 0.5 Mn 1.5 O 4 -coupled full-cell capacity retentions of 81% and 87% for 1000 cycles at 1 C and 2 C, respectively. The studies of the 1000 cycled NPTNO electrode illustrate that the IL-directed mesoporous structure can enhance the cyclability of NPTNO cells due to the alleviation of repetitive mechanical stress and volume fluctuation induced by the repetitive Li + insertion-extraction processes. The measured Li + diffusion coefficients from the galvanostatic intermittent titration technique suggest that the IL-templating strategy indeed ensures the fast rechargeability of NPTNO cells based on the fast Li + diffusion kinetics. Benefitting from the nanoporous structure, NPTNO with unhindered Li + diffusion pathways achieves a superior rate capability in the titanium-based oxide materials and the best full-cell cyclability in the TNO materials. Furthermore, the templating potential of IL is demonstrated, and the superb electrochemical performance establishes the IL-directed NPTNO as a promising anode candidate for fast-rechargeable LIBs.

25 ENERGY STORAGE↗

High Interfacial-Energy and Lithiophilic Janus Interphase Enables Stable Lithium Metal Anodes

The stability of solid electrolyte interphase (SEI) layers is critical for developing lithium (Li) metal batteries. However, the fabrication of stable SEI layers is plagued by un-controlled structures, properties, and functions. In this work a controllable design of an ordered LiF-rich and lithiophilic hybrid Janus interphase (LiF-HJI) is reported using organic fluorination reagent as a functional SEI precursor. The LiF-HJI with a lower crystalline LiF layer and an upper Li organosulfide layer provides high interfacial energy with the Li metal and strong Li-ion affinity, allows homogenous Li-ion distribution, fast and uniform Li-ion transport, and excellent mechanical and passivation properties, enabling stable Li metal anodes under harsh conditions, such as high deposition capacities (6 mA h cm -2 ), current densities (10 mA cm -2 ), and rates (5 C). Stable LiF-HJI@Li greatly improves cycling stability and capacity retention (80.1% after 300 cycles) of Li||LiNi 0.8 Co 0.1 Mn 0.1 O 2 cells at a commercial-level areal capacity (≈4.2 mA h cm -2 ). Even under a lean-electrolyte condition of 3 g Ah -1 , 80% capacity retention can be maintained after 100 cycles, demonstrating excellent cycling performance under such harsh conditions.

25 ENERGY STORAGE↗