Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PLASMA POTENTIAL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Experimental validation of Mueller-Stokes theory and investigation of the influence of the Cotton-Mouton effect on polarimetry in a magnetized fusion plasma

Mueller-Stokes theory can be used to calculate the polarization evolution of an electromagnetic (EM) wave as it propagates through a magnetized plasma. Historically, the theory has been used to interpret polarimeter signals from systems operating on fusion plasmas. These interpretations have mostly employed approximations of Mueller-Stokes theory in regimes where either the Faraday rotation (FR) or the Cotton-Mouton (CM) effect is dominant. The current paper presents the first systematic comparison of polarimeter measurements with the predictions of full Mueller-Stokes theory where conditions transition smoothly from a FR-dominant (i.e., weak CM effect) plasma to one where the CM effect plays a significant role. A synthetic diagnostic code, based on Mueller-Stokes theory accurately reproduces the trends evident in the experimentally measured polarimeter phase over this entire operating range, thereby validating Mueller-Stokes theory. The synthetic diagnostic code is then used to investigate the influence of the CM effect on polarimetry measurements. As expected, the measurements are well approximated by the FR effect when the CM effect is predicted to be weak. However, the code shows that as the CM effect increases, it can compete with the FR effect in rotating the polarization of the EM-wave. This results in a reduced polarimeter response to the FR effect, just as observed in the experiment. The code also shows if sufficiently large, the CM effect can even reverse the handedness of a wave launched with circular polarization. This helps to understand the surprising experimental observations that the sensitivity to the FR effect can be nearly eliminated at high enough B{sub T} (2.0 T). The results also suggest that the CM effect on the plasma midplane can be exploited to potentially measure magnetic shear in tokamak plasmas. These results establish increased confidence in the use of such a synthetic diagnostic code to guide future polarimetry design and interpret the resultant experimental data.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

THE FERMI BUBBLES. II. THE POTENTIAL ROLES OF VISCOSITY AND COSMIC-RAY DIFFUSION IN JET MODELS

The origin of the Fermi bubbles recently detected by the Fermi Gamma-ray Space Telescope in the inner Galaxy is mysterious. In the companion paper Guo and Mathews (Paper I), we use hydrodynamic simulations to show that they could be produced by a recent powerful active galactic nucleus (AGN) jet event. Here, we further explore this scenario to study the potential roles of shear viscosity and cosmic-ray (CR) diffusion on the morphology and CR distribution of the bubbles. We show that even a relatively low level of viscosity ({mu}{sub visc} {approx}> 3 g cm{sup -1} s{sup -1}, or {approx}0.1%-1% of Braginskii viscosity in this context) could effectively suppress the development of Kelvin-Helmholtz instabilities at the bubble surface, resulting in smooth bubble edges as observed. Furthermore, viscosity reduces circulating motions within the bubbles, which would otherwise mix the CR-carrying jet backflow near bubble edges with the bubble interior. Thus viscosity naturally produces an edge-favored CR distribution, an important ingredient to produce the observed flat gamma-ray surface brightness distribution. Generically, such a CR distribution often produces a limb-brightened gamma-ray intensity distribution. However, we show that by incorporating CR diffusion that is strongly suppressed across the bubble surface (as inferred from sharp bubble edges) but is close to canonical values in the bubble interior, we obtain a reasonably flat gamma-ray intensity profile. The similarity of the resulting CR bubble with the observed Fermi bubbles strengthens our previous result in Paper I that the Fermi bubbles were produced by a recent AGN jet event. Studies of the nearby Fermi bubbles may provide a unique opportunity to study the potential roles of plasma viscosity and CR diffusion on the evolution of AGN jets and bubbles.

79 ASTRONOMY AND ASTROPHYSICS↗

EXCITATION OF KINETIC ALFVEN WAVES BY DENSITY STRIATION IN MAGNETO-PLASMAS

Field-aligned density striation is one of the most common inhomogeneity phenomena in magneto-plasmas, such as in the solar coronal plasma and terrestrial auroral plasma. Kinetic Alfven waves (KAWs) can play an important role in the inhomogeneous heating of coronal magneto-plasmas as well as in the local acceleration of auroral energetic electrons. In this paper, we study the dispersion and instability of KAWs in a magneto-plasma with density striation structures. Results show that KAWs become unstable in the presence of the density striation and the corresponding instability has a maximal growth rate at the perpendicular wavelength close to the spatial scale of the density gradient. Related experimental phenomena in both laboratory and space plasmas are discussed. It is suggested that the excitation of KAWs by the density striation of magneto-plasmas can be of potential importance in understanding the physics of the formation of magneto-plasma filaments and their heating mechanisms, which are often present in the terrestrial auroral plasma, the solar coronal plasma, and other astrophysical plasmas.

79 ASTRONOMY AND ASTROPHYSICS↗

Solenoid-free startup experiments in DIII-D

A series of DIII-D experiments was performed to investigate the potential for initiating plasma current using only poloidal field coils located outside the DIII-D central solenoid, i.e. 'solenoid-free'. Plasma current to 166 kA was achieved using 2-3MW of electron cyclotron (EC) heating and was limited by coil and power supply constraints. Flux conversion to plasma current was similar to standard DIII-D startup with some degradation at higher plasma current associated with stray fields and vertical stability issues. In preliminary solenoid-free experiments, neutral beam (NB) current drive (CD) levels were small and attributed to reduced CD efficiency associated with low electron temperature produced by the low current, low confinement plasma. Lack of plasma radial position control also contributed to a reduction of NBCD. Similarly, ECCD was small owing to low plasma temperature and outside EC launch which is required in the solenoid-free scenario. Synergistic experiments were carried out using standard solenoid initiated plasmas in order to study noninductive CD in limited, Lmode plasmas, typical of that generated by solenoid-free startup. While substantial noninductive current can be driven, self-sustaining levels of noninductive current have not yet been achieved with our present six-source co-injection NB system combined with EC and fast wave systems. At low plasma current and high levels of localized EC heating, substantial MHD is generated and this was seen to severely limit plasma performance. Although further optimization is possible in the limited plasma regime, full noninductive, steady-state operation may require diverted plasma with H-mode quality confinement. Discharges obtained during the solenoid-free campaign are compared with results of previous DIII-D campaigns aimed at achieving a steady state, noninductive CD solution.

FACILITY↗

Liquid lithium loop system to solve challenging technology issues for fusion power plant

Here, steady-state fusion power plant designs present major divertor technology challenges, including high divertor heat flux both in steady-state and during transients. In addition to these concerns, there are the unresolved technology issues of long term dust accumulation and associated tritium inventory and safety issues. It has been suggested that radiation-based liquid lithium (LL) divertor concepts with a modest lithium-loop could provide a possible solution for these outstanding fusion reactor technology issues, while potentially improving reactor plasma performance. The application of lithium (Li) in NSTX resulted in improved H-mode confinement, H-mode power threshold reduction, and reduction in the divertor peak heat flux while maintaining essentially Li-free core plasma operation even during H-modes. These promising results in NSTX and related modeling calculations motivated the radiative liquid lithium divertor (RLLD) concept and its variant, the active liquid lithium divertor concept (ARLLD), taking advantage of the enhanced or non-coronal Li radiation in relatively poorly confined divertor plasmas. To maintain the LL purity in a 1 GW-electric class fusion power plant, a closed LL loop system with a modest circulating capacity of ~ 1 liter/second (l/sec) is envisioned. We examined two key technology issues: 1) dust or solid particle removal and 2) real time recovery of tritium from LL while keeping the tritium inventory level to an acceptable level. By running the LL-loop continuously, it can carry the dust particles and impurities generated in the vacuum vessel to the outside where the dust / impurities can be removed by relatively simple dust filter, cold trap and/or centrifugal separation systems. With ~ 1 l/sec LL flow, even a small 0.1% dust content by weight (or 0.5 g per sec) suggests that the LL-loop could carry away nearly 16 tons of dust per year. In a 1 GW-electric (or ~ 3 GW fusion power) fusion power plant, about 0.5 g / sec of tritium is needed to maintain the fusion fuel cycle assuming ~ 1 % fusion burn efficiency. It appears feasible to recover tritium (T) in real time from LL while maintaining an acceptable T inventory level. Laboratory tests are being conducted to investigate T recovery feasibility with the surface cold trap (SCT) concept.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Prediction of electron density and pressure profile shapes on NSTX-U using neural networks

A new model for prediction of electron density and pressure profile shapes on NSTX and NSTX-U has been developed using neural networks. The model has been trained and tested on measured profiles from experimental discharges during the first operational campaign of NSTX-U. By projecting profiles onto empirically derived basis functions, the model is able to efficiently and accurately reproduce profile shapes. In order to project the performance of the model to upcoming NSTX-U operations, a large database of profiles from the operation of NSTX is used to test performance as a function of available data. The rapid execution time of the model is well suited to the planned applications, including optimization during scenario development activities, and real-time plasma control. A potential application of the model to real-time profile estimation is demonstrated.

Boyer, Mark↗

Final Report for "SciDAC Center for Simulation of Wave-Plasma Interactions (CSWPI)"

This project has provided for the participation of the PI (Dr. David Smithe) and other Tech-X Corporation personnel in the larger CSWPI (Center for the Study of Wave Plasma Interactions) SciDAC project. In addition to collaborative efforts in several areas, the PI's thrust research area has focused on the tokamak edge, in the vicinity of the antenna structure, and on the specific physics of interest to the edge, including RF sheath formation. This interest is being driven by a desire to understand measured anomalous power losses that are associated with the edge region. Realistic true 3D geometry simulation capability of the operating antenna, immersed in the edge plasma, has been developed. Geometry accuracy is at the same degree as CAD drawings themselves. In addition, the plasma model includes an RF sheath potential calculation for cells where the plasma is in contact with the metallic structure of the antenna. This capability, in a time-domain simulation, is presently unique. This model can be used to immediately estimate local sheaths (and possibly sputtering damage caused by them), and will be used in the future to model long-range sheaths. Modeling on this scale, in 3D, clearly requires very large scale parallel processing and advanced computing. Ultimately, the desire is to provide quantitative prediction of parasitic edge loss, and edge plasma behavior, analogous to the quantitative core models that have long been a staple of the RF modeling regime.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Comparison of ablators for the polar direct drive exploding pusher platform

We examine the performance of pure boron, boron carbide, high density carbon, and boron nitride ablators in the polar direct drive exploding pusher (PDXP) platform. The platform uses the polar direct drive conguration at the National Ignition Facility to drive high ion temperatures in a room temperature capsule and has potential applications for plasma physics studies and as a neutron source. The higher tensile strength of these materials compared to plastic enables a thinner ablator to support higher gas pressures, which could help optimize its performance for plasma physics experiments, while ablators containing boron enable the possiblity of collecting addtional data to constrain models of the platform. Applying recently developed and experimentally validated equation of state models for the boron materials, we examine the performance of these materials as ablators in 2D simulations, with particular focus on changes to the ablator and gas areal density, as well as the predicted symmetry of the inherently 2D implosion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Radio frequency studies in the NASA Lewis Bumay Torus

The fluctuations in potential of the plasma in the NASA Lewis Bumpy Torus were observed using capacitive probes over frequencies from 1 kHz to 25 MHz and a wide range of operating conditions. The spectra were found to differ greatly above and below a background gas pressure of 3.0.000034 torr deuterium. Above this pressure the spectrum was dominated by the ion spoke frequency and a spectral index was defined. Below this pressure the spectrum below 200 kHz was lower in lower in amplitude by a factor of ten and no spectral index could be defined. At these lower pressures, fluctuations that appeared to be ion spokes were observed, but had a dependence of frequency on operating conditions which was previously unreported.

Gerdin, G. A.↗

Radio frequency studies in the NASA Lewis Bumpy Torus

The fluctuations in potential of the plasma in the NASA Lewis Bumpy Torus are observed using capacitive probes over frequencies from 1 kHz to 25 MHz and a wide range of operating conditions. The spectra are found to differ greatly above and below a background gas pressure of .000034 torr deuterium. Above this pressure, the spectrum is dominated by the ion spoke frequency and a spectral index may be defined. Below this pressure, the spectrum below 200 kHz is lower in amplitude by a factor of ten and no spectral index can be defined. At these lower pressures, fluctuations appearing to be ion spokes are observed, but have a dependence of frequency on operating conditions which is previously unreported.

Gerdin, G. A.↗

A Van der Waals-like theory of plasma double layers

A theory describing plasma double layers in terms of multiple roots of the charge density expression is presented. The theory presented uses the fact that equilibrium plasmas shield small potential perturbations linearly; for high potentials, the shielding decreases. The approach is analogous to Van der Waals' theory of simple fluids in which inclusion of approximate expressions for both excluded volume and long range attractive forces sufficiently describes the first-order liquid-gas phase transition.

Katz, Ira↗

Current collection in a flowing magnetoplasma

Effects of plasma drift on the current collection by a long conducting cylinder in a magnetized plasma is studied by means of a 2 1/2 dimensional PIC code. It is found that for the drift velocity (V sub 0) perpendicular to the magnetic field (B sub 0), the electron current collected by a positive cylinder is considerably enhanced depending on the drift velocity. The distributions of plasma and the potential structure around the cylinder for several relative orientations between V sub 0 and B are presented along with the comparisons of current with and without the magnetic field. Simulations with the magnetic field in the simulation plane show that the potential structures around the cylinder are two-dimensional double layers with dimension (L) perpendicular to B much smaller than the dimension (L) parallel to B. In fact, L perpendicular is found to be approximately determined by the current limiting radius given by the Parker-Murphy model. However, it is found that the collected currents in the simulations are generally higher than those given by this model.

Singh, Nagendra↗

Investigating the Role of the Earth's Ionosphere in Space Weather: Modeling and Observations of High-Latitude Ionospheric Outflows

We will present what we believe to be the first reported observations of up- and downflows of topside ionospheric thermal plasmas from multiple near-simultaneous tracks through the high-latitude topside ionosphere. From several Southern polar passes, it has been possible to construct plots of field-aligned flows of 0+ observed by the Thermal Ion Dynamics Experiment(TIDE) on the POLAR spacecraft near 5000 km altitude together with vertical ion flow observations from one or more DMSP spacecraft near 800 km altitude. We also will present simultaneous observations of POLAR auroral LTVI images with field-aligned flows. We will further show new fluid-kinetic simulations of auroral ionospheric flows in the altitude range 120 km to several R-E as subjected to the synergistic auroral effects of soft electron precipitation, transverse wave-driven ion heating, and hot plasma-driven electric potentials.

Horwitz, J. L.↗

Interplanetary Causes of Great Magnetic Storms: Further Insights

We discuss possible interplanetary mechanisms for the creation of the great magnetic storms at the Earth. We consider the effects of interplanetary shock events on magneic cloud and sheath plasma, leading to potentially stronger interplanetary magnetic field magnitudes.

Magnetic Storms↗

European Strategy for Particle Physics -- Accelerator R&D Roadmap

The 2020 update of the European Strategy for Particle Physics emphasised the importance of an intensified and well-coordinated programme of accelerator R&D, supporting the design and delivery of future particle accelerators in a timely, affordable and sustainable way. This report sets out a roadmap for European accelerator R&D for the next five to ten years, covering five topical areas identified in the Strategy update. The R&D objectives include: improvement of the performance and cost-performance of magnet and radio-frequency acceleration systems; investigations of the potential of laser / plasma acceleration and energy-recovery linac techniques; and development of new concepts for muon beams and muon colliders. The goal of the roadmap is to document the collective view of the field on the next steps for the R&D programme, and to provide the evidence base to support subsequent decisions on prioritisation, resourcing and implementation.

43 PARTICLE ACCELERATORS↗

Collaborative Research: Unravelling the Physics Associated with the Production of Extremely Dense Plasma States of Microscale (Final Report) Nanosecond-pulsed Discharges

The aim of this project is to study and establish the physical mechanisms that contribute to the formation of anomalously dense plasmas in high-pressure nanosecond-pulsed discharges. These discharges have a broad range of applications such as plasma-assisted combustion, plasma flow actuators, biomedical sterilization and exotic materials synthesis. The structure and formation of these discharges, producing high plasma densities of ~10 14 -10 15 cm -3 , are well-studied and understood. Fast-pulsed microscale high-pressure discharges can be driven to even higher densities of > 10 19 cm -3 , approaching warm dense matter conditions. The mechanisms that generate these plasmas have not been understood. Analysis of the warm dense matter state under laboratory conditions is an expensive and non-trivial endeavor. For instance, dense plasmas can be generated by electrical explosions of metal foils and wires. Plasmas generated after the explosion have a short lifetime and often present difficult conditions for diagnostics. Generation of dense plasmas was also achieved during high-voltage nanosecond pulsed discharges when the so-called explosive electron emission is obtained. Unfortunately, this process is very difficult to control for the studies of warm dense matter. In our recent study, we have shown that additional heating of plasma by lasers can further increase the density of plasma and even lead to the fully ionized state. This method, potentially, allows better control of the plasma parameters. In this work, we studied a second stage laser-heated micro-discharge using a self-consistent one-dimensional particle-in-cell Monte Carlo-collision (1D PIC-MCC) model coupled with Maxwell’s equations. We predicted the generation of a fully ionized plasma on the picosecond time scale. However, this model considered the plasma as an ideal gas despite the high pressure and the nearly fully ionized state. The ideal plasma model assumes that the dilute gas approximation is valid, where the inter-particle interactions are negligible. For charged particles this assumption holds as long as the shielded Coulomb potential assumption is valid. For very high plasma densities, this concept breaks down since the Debye sphere surrounding each charged particle no longer contains enough electrons to statistically provide the shielding of the single particle Coulomb interaction potential. At such densities, the plasma can no longer be described as ideal and non-ideal coupling effects need to be considered. In this report, we elucidate our recent work of developing a PIC-MCC model with improvements for non-ideal plasma conditions due to Coulomb coupling at high densities. In particular, we study the interaction of green light radiation and a dense microplasma, and explore the non-ideal plasma effects in this interaction. In this computational model, we implement the two most important non-ideal effects: ionization potential depression (IPD) and enhanced collision cross sections. Our primary goal is to study the physics associated with electromagnetic (EM) wave heating, also called the second-stage wave-heating, and establish the role of plasma non-ideality in this phenomenon. Our secondary goal is to improve the chemistry mechanism of the 1D PIC-MCC model by including a more detailed excited species collision treatment. At high pressures, stepwise ionization from excited species might play an important role in the ionization process. Previously, this ionization mechanism was neglected due to the excitation collision cross section of xenon being smaller than that of ionization. However, a preliminary study showed that the excited species density in the initial microplasma was an order of magnitude higher than the electron density. Therefore, my aim is to determine the significance of this additional ionization pathway to the plasma generation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Beam excited acoustic instability in semiconductor quantum plasmas

The instability of hole-Acoustic waves due to electron beam in semiconductor quantum plasmas is examined using the quantum hydrodynamic model. The quantum effects are considered including Bohm potential, Fermi degenerate pressure, and exchange potential of the semiconductor quantum plasma species. Our model is applied to nano-sized GaAs semiconductor plasmas. The variation of the growth rate of the unstable mode is obtained over a wide range of system parameters. It is found that the thermal effects of semiconductor species have significance over the hole-Acoustic waves.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The Thermal Ion Dynamics Experiment and Plasma Source Instrument

The Thermal Ion Dynamics Experiment (TIDE) and the Plasma Source Instrument (PSI) have been developed in response to the requirements of the ISTP Program for three-dimensional (3D) plasma composition measurements capable of tracking the circulation of low-energy (0-500 eV) plasma through the polar magnetosphere. This plasma is composed of penetrating magnetosheath and escaping ionospheric components. It is in part lost to the downstream solar wind and in part recirculated within the magnetosphere, participating in the formation of the diamagnetic hot plasma sheet and ring current plasma populations. Significant obstacles which have previously made this task impossible include the low density and energy of the outflowing ionospheric plasma plume and the positive spacecraft floating potentials which exclude the lowest-energy plasma from detection on ordinary spacecraft. Based on a unique combination of focusing electrostatic ion optics and time of flight detection and mass analysis, TIDE provides the sensitivity (seven apertures of about 1 cm squared effective area each) and angular resolution (6 x 18 degrees) required for this purpose. PSI produces a low energy plasma locally at the POLAR spacecraft that provides the ion current required to balance the photoelectron current, along with a low temperature electron population, regulating the spacecraft potential slightly positive relative to the space plasma. TIDE/PSI will: (a) measure the density and flow fields of the solar and terrestrial plasmas within the high polar cap and magnetospheric lobes; (b) quantify the extent to which ionospheric and solar ions are recirculated within the distant magnetotail neutral sheet or lost to the distant tail and solar wind; (c) investigate the mass-dependent degree energization of these plasmas by measuring their thermodynamic properties; (d) investigate the relative roles of ionosphere and solar wind as sources of plasma to the plasma sheet and ring current.

Moore, T. E.↗