Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PARTIAL PRESSURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,045 records · Page 58

Interactions of nickel/zirconia solid oxide fuel cell anodes with coal gas containing arsenic

The performance of anode-supported and electrolyte-supported solid oxide fuel cells was investigated in synthetic coal gas containing 0 to 10 ppm arsenic introduced as arsine. Arsenic was found to interact strongly with nickel in the anode, resulting in the formation of nickel-arsenic solid solution, Ni5As2 and Ni11As8, depending on temperature, arsenic concentration, and reaction time. For anode-supported cells, loss of electrical connectivity in the anode support was the principal mode of degradation, as nickel was converted to nickel arsenide phases that migrated to the surface to form large grains. Cell failure occurred well before the entire anode was converted to nickel arsenide, and followed a reciprocal square root of arsenic partial pressure dependence consistent with a diffusion-based rate-limiting step. Failure occurred more quickly with electrolyte-supported cells, which have a substantially smaller nickel inventory. For these cells, time to failure varied linearly with the reciprocal arsenic concentration in coal gas, and occurred when arsenic reached the anode/electrolyte interface. Test performed with nickel/zirconia coupons showed that arsenic was essentially completely captured in a narrow band near the fuel gas inlet.

Environmental Molecular Sciences Laboratory↗

Ambient Operation of Li/Air Batteries

In this work, Li/air batteries based on nonaqueous electrolytes were investigated in ambient conditions (with an oxygen partial pressure of 0.21 atm and relative humidity of ~20%). A heat-sealable polymer membrane was used as both an oxygen-diffusion membrane and as a moisture barrier for Li/air batteries. The membrane also can minimize the evaporation of the electrolyte from the batteries. Li/air batteries with this membrane can operate in ambient conditions for more than one month with a specific energy of 362 Wh kg-1, based on the total weight of the battery including its packaging. Among various carbon sources used in this work, Li/air batteries using Ketjenblack (KB) carbon-based air electrodes exhibited the highest specific energy. However, KB-based air electrodes expanded significantly and absorbed much more electrolyte than electrodes made from other carbon sources. The weight distribution of a typical Li/air battery using the KB-based air electrode was dominated by the electrolyte (~70%). Lithium-metal anodes and KB-carbon anodes account for only 5.12% and 5.78% of the battery weight, respectively. We also found that only ~ 20% of the mesopore volume of the air electrode was occupied by reaction products after discharge. To further improve the specific energy of the Li/air batteries, the microstructure of the carbon electrode needs to be further improved to absorb much less electrolyte while still holding significant amounts of reaction products

energy storage↗

Advanced Ceramic Interconnect Material for Solid Oxide Fuel Cells: Electrical and Thermal Properties of Calcium- and Nickel-Doped Yttrium Chromites

The structural, thermal and electrical characteristics of calcium- and nickel-doped yttrium chromites were studied for potential use as the interconnect material in high temperature solid oxide fuel cells (SOFCs) and other high temperature electrochemical and thermoelectric devices. The Y0.8Ca0.2Cr1-xNixO3±δ compositions with x=0-0.15 showed single phase orthorhombic perovskite structures between 25 and 1200 degrees C over a wide range of oxygen partial pressures. Nickel doping remarkably enhanced sintering behavior of otherwise refractory chromites, and densities 94% of theoretical density were obtained after sintering at 1400 degrees C in air with 15 at.% Ni. The thermal expansion coefficient (TEC) was increased with nickel content to closely match that of an 8 mol% yttria-stabilized zirconia (YSZ) electrolyte for 0.05 ≤ x ≤ 0.15. Nickel doping significantly improved the electrical conductivity in both oxidizing and reducing atmospheres. Undesirable oxygen ion leakage current was insignificant in dual atmosphere conditions. No interfacial interactions with YSZ were detected after firing at 1400 degrees C.

Yoon, Kyung J↗

New insights in the polarization resistance of anode-supported solid oxide fuel cells with La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 cathodes

In this study, the polarization resistance of the La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 (LSCF) solid oxide fuel cell (SOFC) cathode was investigated by I-V sweep and electrochemcial impedance spectroscopy under a series of dc bias voltages and cathode environments (i.e. stagnant air, flowing air, and flowing oxygen) at temperatures from 550 to 750 °C. In flowing oxygen, the polarization resistance of the fuel cell decreased considerably with the applied current density. A linear relationship was observed between the ohmic-free over-potential and the logarithm of the current density of the fuel cell at all the measuring temperatures. In stagnant or flowing air, a new arc related to the molecular oxygen diffusion in the pores of the cathode was identified at high temperatures and high current densities. The magnitude of this arc increased with the applied current density due to the decreased oxygen partial pressure at the interface of the cathode and the electrolyte. It is found that the performance of the fuel cell in air is mainly determined by the oxygen diffusion process. Elimination of this process by flowing oxygen to the cathode improved the cell performance significantly. At 750 °C, for a fuel cell with a laser-deposited Sm 0.2 Ce 0.8 O 1.9 (SDC) interlayer, an extraordinarily high power density of 2.6 W cm -2 at 0.7 V was achieved in flowing oxygen, as a result of reduced ohmic and polarization resistance of the fuel cell, which were 0.06 Ω cm 2 and 0.03 Ω cm 2 , respectively. The results indicate that optimization of the microstructure of the LSCF cathode or adoption of a new cell design which can mitigate the diffusion problem in the cathode might enhance cell performance significantly.

concentration polarization↗

A new composite cathode for intermediate temperature solid oxide fuel cells with zirconia-based electrolytes

Improving the electrocatalytic activity of electrode materials is vitally important to achieve practically meaningful performance for intermediate temperature solid oxide fuel cells (IT-SOFCs). Here the present work develops a composite cathode consisting of an electronic conductor Sr-doped LaMnO 3 (LSM) and an ionic conductor Y- and Ce- co-doped Bi 2 O 3 (BYC7). BYC7 is an excellent oxide-ion conductor, exhibiting a high and stable ionic conductivity of 0.008 S cm -1 at 500 °C. The polarization resistance of LSM-BYC7 cathode in a symmetrical cell with doped ZrO 2 as electrolyte varies from 5.76 at 500 °C to 0.25 Ω cm 2 at 650 °C. The surface diffusion and charge transfer at the triple phase boundaries are the rate determining steps based on the dependence of polarization resistance on partial pressure of oxygen. The maximum power density of a ZrO 2 -based anode-supported cell with LSM-BYC7 composite cathode is 56.4, 154.6, 327.9, and 451.0 mW cm-2 at 500, 550, 600, and 650 °C respectively. AC impedance analysis reveals that the performance of IT-SOFC prepared in this study is actually limited by the anode, not by LSM-BYC7 cathode.

25 ENERGY STORAGE↗

Analysis of alkaline exchange membrane fuel cells performance at different operating conditions using DC and AC methods

We report membrane electrode assemblies (MEAs) for anion exchange membrane fuel cells (AEMFCs) were manufactured from commercial materials: Pt/C catalyst, A201 AEM and AS4 ionomer by using an industrial mass-production digital printing method. The MEA designs selected are close to those recommended by US Department of Energy, including low loading of platinum on the cathode side (0.2 mg cm -2 ). Polarization curves and electrochemical impedance spectroscopy (EIS) were applied for MEA evaluation in fuel cell conditions with variation of gas humidification and oxygen partial pressure (air vs oxygen). The typical impedance curves recorded at H 2 /O 2 gas configuration consist of high- and medium-frequency arcs responsible for hydrogen oxidation and oxygen reduction, respectively. Operation with air as a cathode feed gas resulted in a decrease in AEMFC performance due to possible CO 2 poisoning and mass transfer losses. At the same time, EIS demonstrated formation of a low frequency loop due to diffusion limitations. Despite the low loading of platinum on the cathode (0.2 mg cm -2 ), a peak power density of ~330 mW cm -2 was achieved (at 50/50% of RH on anode and cathode), which is substantially higher performance than for AEMFC MEAs tested at similar conditions.

25 ENERGY STORAGE↗

Modeling Ni redistribution in the hydrogen electrode of solid oxide cells through Ni(OH) 2 diffusion and Ni-YSZ wettability change

Ni redistribution in the hydrogen electrodes of solid oxide cells is an important degradation mechanism. Its driving force is still under debate. This work focuses on the interplay between Ni(OH) 2 diffusion and Ni-YSZ wettability change. With a Ni(OH) 2 diffusion model developed in our previous work, we further employ three models for the Ni-YSZ contact angle to quantify the Ni-YSZ wettability change. The microstructure evolutions in a reconstructed Ni-YSZ electrode are simulated under selected experimental operating conditions. It is shown that the phenomenological model can capture the driving force of Ni spreading/detachment on YSZ surface and the Ni migration reported in experiments can be qualitatively reproduced through the competition between Ni(OH) 2 diffusion and Ni-YSZ wettability change. It is also found that the initial microstructure of the active layer and the microstructure characteristics in the support layer can strongly affect the distribution of steam partial pressure and overpotential, hence the Ni redistribution, in the active layer, which may explain the inconsistencies in experiments. Further, our results show that there are two missing pieces in current theory of Ni redistribution: a mechanism of fast Ni diffusion under humid atmosphere and the physical reason behind the Ni spreading/detachment.

25 ENERGY STORAGE↗

Ni coarsening under humid atmosphere in the electrode of solid oxide cells: A combined study of density-functional theory and phase-field modeling

Ni coarsening in solid oxide cell (SOC) electrodes is known to be significantly faster under a humid atmosphere. The underlying mechanisms, though, have not been fully understood. In this work, we examine the surface diffusion of Ni(OH) x by a combination of density-functional theory and phase-field modeling. Here, density-functional theory is used to evaluate the adsorption and diffusion of the Ni(OH) x species on Ni (111) surface, and the results are used to obtain the effective surface diffusivity of Ni versus steam and hydrogen gas partial pressures. This diffusivity is used as an input for a phase-field model to investigate the Ni coarsening in SOC electrodes. It is found that Ni(OH) x formed through chemical reaction cannot accelerate coarsening unless an extremely high steam to hydrogen ratio is reached. However, if Ni(OH) x is formed through electrochemical reactions near triple phase boundaries (TPBs), surface diffusion of Ni(OH) x may cause faster Ni coarsening in fuel cell mode under a large overpotential. Specifically, surface diffusion of Ni(OH) may be comparable to or faster than that of Ni under an overpotential that is large but still possible under fuel cell operating conditions.

25 ENERGY STORAGE↗

An infrared spectral database for gas-phase quantitation of volatile per- and polyfluoroalkyl substances (PFAS)

We report the construction of a database of vetted infrared spectra specifically targeting volatile fluorocarbon gases that may be emitted during thermal treatment of per- and polyfluoroalkyl substances (PFAS) to assist understanding of treatment processes and improve quantification. To populate this database, protocols derived from the Pacific Northwest National Laboratory (PNNL) infrared spectral database are used, curtailing the species selection for this data set. Each spectrum in the database is a weighted average derived from 10 or more individual measurements at different partial pressures (static method) or flow rates (dissemination method) to yield good fidelity of both strong and weak infrared signatures, with each composite spectrum ranging from = 6500 cm-1 to = 600 cm-1 with an apodized resolution of 0.112 cm-1. This resolution was chosen to fully resolve all spectral features, recognizing that atmospheric pressure broadening results in nearly all ro-vibrational lines having linewidths = 0.1 cm-1. As an example case, application of the database is demonstrated via identification and quantification of dominant 1H-perfluoroheptane and perfluorohept-1-ene fluorocarbon products resulting from thermal decomposition of perfluorooctanoate (PFOA) below 450 °C.

Infrared, Gas-phase spectra, FTIR, Spectral databa↗

A new defect chemistry model for Nb-doped SrCoO 2.5+δ: The role of oxygen interstitials and delocalized-to-localized electron holes

Here a new defect chemistry model featuring oxygen interstitials ( O" I ) and delocalized-to-localized d-electron holes (Co' Co 2.5 reference framework to elucidate transport properties of Nb-doped SrCoO 2.5+δ (SCN) system over a range of partial pressure of oxygen (Po 2 ) and temperature (T). With this new defect chemistry model, the electronic conductivity behaviors with T and Po2 can be well interpreted by the change in concentration of d-electron holes migrating with a constant mobility. The important concentration contours of electron holes, excess electrons and oxygen interstitials are mapped out on the T-Po 2 domain, from which hole-concentration and conductivity under iso-stoichiometry are reconstructed. The partial/integral molar thermodynamic properties and thermodynamic factor of the SCN solid solution are also determined. A transitional delocalized-to-localized hole-transport mechanism with decreasing oxygen stoichiometry is discussed based on p=p(T) obtained under constant oxygen stoichiometry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of laser power on oxygen and nitrogen concentration of commercially pure titanium manufactured by selective laser melting

Highlights: • The hardness and strength of pure titanium fabricated by SLM were increased with increasing the laser power. • During the SLM processing, the concentrations of oxygen and nitrogen in the SLM parts were increased. • The oxidation and nitriding were thermodynamically possible under SLM. - Abstract: This study analyzed the variation of mechanical properties and its causes with increasing the laser power in the fabrication of pure titanium by selective laser melting (SLM). SLM samples were fabricated using commercially pure titanium grade 1 powder when the scan speed was 1000 mm/s and the laser power as 120, 200, 280, 360, and 440 W, respectively. As the laser power increased, the hardness and strength of the samples increased gradually. During the SLM processing, the concentrations of oxygen and nitrogen in the SLM samples were increased, which resulted in the increase of hardness and strength. The SLM equipment used in this study removed oxygen in the chamber by flowing high purity argon gas and fabricates the sample while preserving the oxygen concentration in the atmosphere to 0.2%. Evaluating the possibility of oxidation and nitriding during the SLM process by thermodynamic analysis, it was found that the process occurred under conditions in which temperature and residual oxygen and nitrogen partial pressure led to oxidation and nitriding.

36 MATERIALS SCIENCE↗

A mechanistic interpretation of Nelson curves for PVP failures under high temperature hydrogen attack

As an empirically established design criterion, Nelson curves that relate the service temperature and the allowable hydrogen partial pressure have been developed and utilized for more than sixty years in pressure vessels and piping (PVP) safety design. Despite a relatively clear thermodynamic understanding of the high-temperature-hydrogen-attack (HTHA) problem, the detailed fracture process on the microstructural length scales, however, remains elusive, and a quantitative assessment of the PVP lifetime under HTHA from the available creep fracture dataset is still not possible. This work develops a microstructure-informed and micromechanics-based model by incorporating a synergy between hydrogen transport and intergranular-cavity-based fracture process. Based on the available creep lifetime data of C-0.5Mo steels, we are able to calibrate material constitutive parameters, and then conduct nonlinear finite element simulations that reveal a real-time stress-induced hydrogen diffusional transport along grain boundaries, coupled with a microstructure-explicit failure process, from which Nelson curves can be computed. Such failure analyses allow us to delineate two distinct regimes on the Nelson curves, i.e., dislocation-creep-controlled or grain boundary diffusion-assisted cavity growth. More importantly, we found that a small change of the pipe thickness and applied stresses can significantly shift these lifetime curves. However, these two parameters are usually not provided in Nelson curves, thus limiting their usage in material selection and safety design. In conclusion, this discrepancy can clearly be mitigated by extensive parametric studies from our micromechanical modeling/simulation framework.

36 MATERIALS SCIENCE↗

Hydrogen embrittlement of Zircaloy-4 fabricated by ultrasonic additive manufacturing

Ultrasonic additive manufacturing (UAM) was successfully applied to the zirconium material system to create a planar geometry. Following fabrication, SS-J3 type tensile specimens of the UAM and wrought Zircaloy-4 with a nominal gage section of 5×1.2×0.75 mm were machined for hydriding studies and mechanical testing. The SS-J3 type tensile specimens were gas-charged with hydrogen using a custom system that precisely controls hydrogen gas flow rate, hydrogen partial pressure, and temperature. To avoid altering the UAM material, the maximum process temperature was limited to 550°C. Using different initial hydrogen gas pressures and flow rates, various hydrogen contents (70–1755 wppm) were achieved for Zircaloy-4 specimens. Tensile testing shows that, regardless of hydrogen content, all UAM specimens measured yield strengths in the range of 557±16 MPa and ultimate tensile strengths of 660±4MPa. However, total elongation clearly decreased as a function of increasing hydrogen content. Further, at the lowest hydrogen content, the total plastic elongation measured 21.5%, and this value decreased to less than 2% when the hydrogen content was increased to 1000 wppm. Cross-sectional optical microscopy images revealed that the hydride distributions are randomly oriented. For the low hydrogen content specimen, these randomly distributed hydrides are isolated from each other. A sandwiched structure, consisting of high-density and low-density layers, was also observed for the specimens with hydrogen content between 200 and 400 wppm. As the hydrogen content increases, the hydrides diffuse into the low-density hydride layers to form a network across the whole specimen. Although the tensile properties of UAM and wrought Zircaloy-4 exhibit the same behavior with increasing hydrogen content, the distinctions in grain orientations led to differences in the hydride orientations at low and intermediate hydrogen concentrations.

36 MATERIALS SCIENCE↗

Trace level of atomic copper in N-doped graphene quantum dots switching the selectivity from C 1 to C 2 products in CO electroreduction

To unravel the relationship between trace Cu on the metal-free catalysts toward CO/CO 2 reduction reaction (CO/CO 2 RR), we investigated the effect of trace Cu loading in N-doped graphene quantum dots (NGQDs) on CO/CO 2 RR. A general trend is that increasing the Cu loading in NGQDs switches the selectivity from C 1 (CH 4 ) to C 2 products in CORR. When 2.5 μg/cm 2 Cu with the atomic size is loaded on NGQDs, the selectivity shifts from 62% Faradaic efficiency (FE) of CH 4 to 52% FE of C 2 products in CORR. Further increasing the atomic Cu loading to 3.8 μg/cm 2 promotes the FE of C 2 products to 78%. CO 2 RR requires one order of magnitude higher Cu loading than CORR to switch the selectivity from C 1 to C 2 products due to the low partial pressure of CO. Finally, this study clarifies the distinct impact of trace (ppm level) Cu on the activity/selectivity between CORR and CO 2 RR.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Challenges in computationally designing high temperature Fe-based austenitic alloys: Addressing the role of Ni additions

Alumina-forming austenitic (AFA) alloys are relatively inexpensive high performance materials which combine the creep resistance of low-cost austenitic alloys and the oxidation resistance of expensive alumina forming alloys. However, a fundamental understanding of the role of key alloying elements such as Ni, Cr, Al, Nb, Ti, V, B and C in the experimentally observed oxidation behavior of these alloys is still lacking. The present work is a first in a series of studies aiming to quantitatively describe the role of Ni in promoting or disrupting protective Al 2 O 3 scale formation on AFA alloys. Here, ternary Fe-Al-xNi model alloys with three different Ni contents were isothermally exposed in an atmosphere with a low partial pressure of oxygen between 800–1000 °C for 24 h to evaluate the role of Ni in the observed internal oxidation behavior. Increasing Ni contents had no impact on the internal oxidation behavior of the alloys. The experimental and theoretical analyses in the present work suggested a negligible effect of the internal oxide precipitates on the inward diffusion of oxygen, typically expected in these systems, while simultaneously highlighting the barriers in the development of reliable models for computation-assisted design of these alloys.

36 MATERIALS SCIENCE↗

Ultra-fast and sensitive magneto-optical hydrogen sensors using a magnetic nano-cap array

Magnetism in curved nano-geometries has opened a new path to design novel characteristics and phenomena that could greatly impact the future fundamental and applied studies of materials. Here, in this report, a hexagonally-packed array of magnetic nano-caps (or nano-patches, NP) exhibiting unique magnetic anisotropy and optimal nanostructure for fast hydrogen kinetics is explored as a sensing element for the spark-free magnetic-circular-dichroism (MCD) H 2 sensor. The MCD H 2 sensor outperforms the state-of-the-art optical sensors reported to date and satisfies the most challenging performance targets imposed by US Department of Energy. In particular, a Pd 67 Co 33 NP sensor exhibits response time of t 90 < 0.9 s, recovery time of t 10 < 9.0 s over the 1-100 mbar H 2 partial pressure range, and limit of detection (LOD) of ~1 ppm. The LOD improves to <700 ppb, when the signal-to-noise ratio is enhanced by stacking three NP arrays. Using a 30-nm TAF (Teflon AF 2400) polymer coating, the sorption kinetics of the Pd 67 Co 33 /TAF sensor are significantly accelerated, with t 90 < 0.4 s and t 10 < 2.8 s over the same pressure range. When the Pd 67 Co 33 /TAF sensor is further coated with a 100-nm poly(methyl methacrylate) (PMMA) layer, a rapid sorption time of t 90 < 0.5 s, LOD < 1 ppm and excellent sensor accuracy (<2.5% full scale) are maintained, while the sensor obtains strong selectivity against interference gases and moisture and a negligible aging effect. The MCD nano-cap sensor platform may have a great impact on the future deployment of H 2 fuel, H 2 environmental monitoring sensors, and fast proton-based magneto-ionic devices.

Fast and sensitive hydrogen sensors↗

EXPLORING THE STRUCTURE OF GLASS-FORMING LIQUIDS USING HIGH ENERGY X-RAY DIFFRACTION, CONTAINERLESS METHODOLOGY AND STATE-OF-THE-ART MOLECULAR DYNAMICS SIMULATION

High energy X-ray diffraction can be combined with containerless techniques to provide information on the atomic arrangements in glass-forming liquids in stable and metastable regimes. The high incident energies provide bulk diffraction data to high values of scattering vector which enables significantly more robust analysis of the local and medium-range order that influences important physical properties such as viscosity and crystal nucleation. These combined techniques have been applied to a range of oxide liquids. In this contribution we illustrate addition of further dimensions to phase space by controlling the partial pressure of oxygen that permits the study liquids containing iron. The advantages of rapid data acquisition are also demonstrated in a study of tellurite glass-forming systems where a transition from ergodic to non-ergodic regimes in the deeply supercooled liquid is shown. Finally we demonstrate how descriptions of the liquid structure can be developed by combining HEXRD with molecular dynamics simulations.

containerless techniques↗

Regenerable solvents mediate accelerated low temperature CO 2 capture and carbon mineralization of ash and nano-scale calcium carbonate formation

The dual need to remove CO 2 from our emissions and treat alkaline industrial residues such as ash materials motivate the design of innovative pathways to simultaneously capture and convert CO 2 into mineralized carbonates. Direct carbon mineralization is one approach that addresses the need to simultaneously treat alkaline industrial residues and mineralize CO 2 emissions. Low CO 2 solubility in water and slow kinetics at ambient temperature have challenged the direct carbon mineralization of alkaline industrial residues. Here, to address these challenges, the use of CO 2 capture solvents that enhance CO 2 solubility and facilitate accelerated carbon mineralization of fly ash at temperatures below 90 °C is investigated. Calcium carbonate formation results in the inherent regeneration of the solvent. The carbon mineralization extents of non-calcium carbonate content in fly ash were 50% and 51% and in waste ash were 58% and 62% in 2.5 M sodium glycinate and 30 wt% MEA solutions, respectively. The experiments were performed at 50 °C for 3 hours with CO 2 partial pressure of 1 atm in a continuously stirred slurry environment with 15 wt.% solid. Furthermore, nanoscale CaCO 3 is successfully synthesized from dissolved calcium using CO 2 -loaded sodium glycinate and surfactants such as CTAB (Cetyl Trimethyl Ammonium Bromide). Surfactants such as CTAB bind to the calcium carbonate surface and regulate the growth of calcium carbonate particles. These innovative approaches demonstrate the feasibility of directly storing CO 2 in fly ash and waste ash as calcium carbonate and producing nanoscale calcium carbonate using regenerable CO 2 capture solvents.

42 ENGINEERING↗